OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [orpsocv2/] [boards/] [xilinx/] [ml501/] [rtl/] [verilog/] [include/] [uart_defines.v] - Rev 503

Go to most recent revision | Compare with Previous | Blame | View Log

//////////////////////////////////////////////////////////////////////
////                                                              ////
////  uart_defines.v                                              ////
////                                                              ////
////                                                              ////
////  This file is part of the "UART 16550 compatible" project    ////
////  http://www.opencores.org/cores/uart16550/                   ////
////                                                              ////
////  Documentation related to this project:                      ////
////  - http://www.opencores.org/cores/uart16550/                 ////
////                                                              ////
////  Projects compatibility:                                     ////
////  - WISHBONE                                                  ////
////  RS232 Protocol                                              ////
////  16550D uart (mostly supported)                              ////
////                                                              ////
////  Overview (main Features):                                   ////
////  Defines of the Core                                         ////
////                                                              ////
////  Known problems (limits):                                    ////
////  None                                                        ////
////                                                              ////
////  To Do:                                                      ////
////  Nothing.                                                    ////
////                                                              ////
////  Author(s):                                                  ////
////      - gorban@opencores.org                                  ////
////      - Jacob Gorban                                          ////
////      - Igor Mohor (igorm@opencores.org)                      ////
////                                                              ////
////  Created:        2001/05/12                                  ////
////  Last Updated:   2001/05/17                                  ////
////                  (See log for the revision history)          ////
////                                                              ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
////                                                              ////
//// Copyright (C) 2000, 2001 Authors                             ////
////                                                              ////
//// This source file may be used and distributed without         ////
//// restriction provided that this copyright statement is not    ////
//// removed from the file and that any derivative work contains  ////
//// the original copyright notice and the associated disclaimer. ////
////                                                              ////
//// This source file is free software; you can redistribute it   ////
//// and/or modify it under the terms of the GNU Lesser General   ////
//// Public License as published by the Free Software Foundation; ////
//// either version 2.1 of the License, or (at your option) any   ////
//// later version.                                               ////
////                                                              ////
//// This source is distributed in the hope that it will be       ////
//// useful, but WITHOUT ANY WARRANTY; without even the implied   ////
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR      ////
//// PURPOSE.  See the GNU Lesser General Public License for more ////
//// details.                                                     ////
////                                                              ////
//// You should have received a copy of the GNU Lesser General    ////
//// Public License along with this source; if not, download it   ////
//// from http://www.opencores.org/lgpl.shtml                     ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
//
// CVS Revision History
//
// $Log: not supported by cvs2svn $
// Revision 1.13  2003/06/11 16:37:47  gorban
// This fixes errors in some cases when data is being read and put to the FIFO at the same time. Patch is submitted by Scott Furman. Update is very recommended.
//
// Revision 1.12  2002/07/22 23:02:23  gorban
// Bug Fixes:
//  * Possible loss of sync and bad reception of stop bit on slow baud rates fixed.
//   Problem reported by Kenny.Tung.
//  * Bad (or lack of ) loopback handling fixed. Reported by Cherry Withers.
//
// Improvements:
//  * Made FIFO's as general inferrable memory where possible.
//  So on FPGA they should be inferred as RAM (Distributed RAM on Xilinx).
//  This saves about 1/3 of the Slice count and reduces P&R and synthesis times.
//
//  * Added optional baudrate output (baud_o).
//  This is identical to BAUDOUT* signal on 16550 chip.
//  It outputs 16xbit_clock_rate - the divided clock.
//  It's disabled by default. Define UART_HAS_BAUDRATE_OUTPUT to use.
//
// Revision 1.10  2001/12/11 08:55:40  mohor
// Scratch register define added.
//
// Revision 1.9  2001/12/03 21:44:29  gorban
// Updated specification documentation.
// Added full 32-bit data bus interface, now as default.
// Address is 5-bit wide in 32-bit data bus mode.
// Added wb_sel_i input to the core. It's used in the 32-bit mode.
// Added debug interface with two 32-bit read-only registers in 32-bit mode.
// Bits 5 and 6 of LSR are now only cleared on TX FIFO write.
// My small test bench is modified to work with 32-bit mode.
//
// Revision 1.8  2001/11/26 21:38:54  gorban
// Lots of fixes:
// Break condition wasn't handled correctly at all.
// LSR bits could lose their values.
// LSR value after reset was wrong.
// Timing of THRE interrupt signal corrected.
// LSR bit 0 timing corrected.
//
// Revision 1.7  2001/08/24 21:01:12  mohor
// Things connected to parity changed.
// Clock devider changed.
//
// Revision 1.6  2001/08/23 16:05:05  mohor
// Stop bit bug fixed.
// Parity bug fixed.
// WISHBONE read cycle bug fixed,
// OE indicator (Overrun Error) bug fixed.
// PE indicator (Parity Error) bug fixed.
// Register read bug fixed.
//
// Revision 1.5  2001/05/31 20:08:01  gorban
// FIFO changes and other corrections.
//
// Revision 1.4  2001/05/21 19:12:02  gorban
// Corrected some Linter messages.
//
// Revision 1.3  2001/05/17 18:34:18  gorban
// First 'stable' release. Should be sythesizable now. Also added new header.
//
// Revision 1.0  2001-05-17 21:27:11+02  jacob
// Initial revision
//
//
 
// remove comments to restore to use the new version with 8 data bit interface
// in 32bit-bus mode, the wb_sel_i signal is used to put data in correct place
// also, in 8-bit version there'll be no debugging features included
// CAUTION: doesn't work with current version of OR1200
`define DATA_BUS_WIDTH_8
 
`ifdef DATA_BUS_WIDTH_8
 `define UART_ADDR_WIDTH 3
 `define UART_DATA_WIDTH 8
`else
 `define UART_ADDR_WIDTH 5
 `define UART_DATA_WIDTH 32
`endif
 
// Uncomment this if you want your UART to have
// 16xBaudrate output port.
// If defined, the enable signal will be used to drive baudrate_o signal
// It's frequency is 16xbaudrate
 
// `define UART_HAS_BAUDRATE_OUTPUT
 
// Register addresses
`define UART_REG_RB	`UART_ADDR_WIDTH'd0	// receiver buffer
`define UART_REG_TR  `UART_ADDR_WIDTH'd0	// transmitter
`define UART_REG_IE	`UART_ADDR_WIDTH'd1	// Interrupt enable
`define UART_REG_II  `UART_ADDR_WIDTH'd2	// Interrupt identification
`define UART_REG_FC  `UART_ADDR_WIDTH'd2	// FIFO control
`define UART_REG_LC	`UART_ADDR_WIDTH'd3	// Line Control
`define UART_REG_MC	`UART_ADDR_WIDTH'd4	// Modem control
`define UART_REG_LS  `UART_ADDR_WIDTH'd5	// Line status
`define UART_REG_MS  `UART_ADDR_WIDTH'd6	// Modem status
`define UART_REG_SR  `UART_ADDR_WIDTH'd7	// Scratch register
`define UART_REG_DL1	`UART_ADDR_WIDTH'd0	// Divisor latch bytes (1-2)
`define UART_REG_DL2	`UART_ADDR_WIDTH'd1
 
// Interrupt Enable register bits
`define UART_IE_RDA	0	// Received Data available interrupt
`define UART_IE_THRE	1	// Transmitter Holding Register empty interrupt
`define UART_IE_RLS	2	// Receiver Line Status Interrupt
`define UART_IE_MS	3	// Modem Status Interrupt
 
// Interrupt Identification register bits
`define UART_II_IP	0	// Interrupt pending when 0
`define UART_II_II	3:1	// Interrupt identification
 
// Interrupt identification values for bits 3:1
`define UART_II_RLS	3'b011	// Receiver Line Status
`define UART_II_RDA	3'b010	// Receiver Data available
`define UART_II_TI	3'b110	// Timeout Indication
`define UART_II_THRE	3'b001	// Transmitter Holding Register empty
`define UART_II_MS	3'b000	// Modem Status
 
// FIFO Control Register bits
`define UART_FC_TL	1:0	// Trigger level
 
// FIFO trigger level values
`define UART_FC_1		2'b00
`define UART_FC_4		2'b01
`define UART_FC_8		2'b10
`define UART_FC_14	2'b11
 
// Line Control register bits
`define UART_LC_BITS	1:0	// bits in character
`define UART_LC_SB	2	// stop bits
`define UART_LC_PE	3	// parity enable
`define UART_LC_EP	4	// even parity
`define UART_LC_SP	5	// stick parity
`define UART_LC_BC	6	// Break control
`define UART_LC_DL	7	// Divisor Latch access bit
 
// Modem Control register bits
`define UART_MC_DTR	0
`define UART_MC_RTS	1
`define UART_MC_OUT1	2
`define UART_MC_OUT2	3
`define UART_MC_LB	4	// Loopback mode
 
// Line Status Register bits
`define UART_LS_DR	0	// Data ready
`define UART_LS_OE	1	// Overrun Error
`define UART_LS_PE	2	// Parity Error
`define UART_LS_FE	3	// Framing Error
`define UART_LS_BI	4	// Break interrupt
`define UART_LS_TFE	5	// Transmit FIFO is empty
`define UART_LS_TE	6	// Transmitter Empty indicator
`define UART_LS_EI	7	// Error indicator
 
// Modem Status Register bits
`define UART_MS_DCTS	0	// Delta signals
`define UART_MS_DDSR	1
`define UART_MS_TERI	2
`define UART_MS_DDCD	3
`define UART_MS_CCTS	4	// Complement signals
`define UART_MS_CDSR	5
`define UART_MS_CRI	6
`define UART_MS_CDCD	7
 
// FIFO parameter defines
 
`define UART_FIFO_WIDTH	8
`define UART_FIFO_DEPTH	16
`define UART_FIFO_POINTER_W	4
`define UART_FIFO_COUNTER_W	5
// receiver fifo has width 11 because it has break, parity and framing error bits
`define UART_FIFO_REC_WIDTH  11
 
 
`define VERBOSE_WB  0           // All activity on the WISHBONE is recorded
`define VERBOSE_LINE_STATUS 0   // Details about the lsr (line status register)
`define FAST_TEST   1           // 64/1024 packets are sent
 
// Defines hard baud prescaler register - uncomment to enable
//`define PRESCALER_PRESET_HARD
// 115200 baud preset values
// 20MHz: prescaler 10.8 (11, rounded up)
//`define PRESCALER_HIGH_PRESET 8'd0
//`define PRESCALER_LOW_PRESET 8'd11
// 50MHz: prescaler 27.1
//`define PRESCALER_HIGH_PRESET 8'd0
//`define PRESCALER_LOW_PRESET 8'd27
// 66MHz: prescaler 36.1
//`define PRESCALER_HIGH_PRESET 8'd0
//`define PRESCALER_LOW_PRESET 8'd36
 
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.