URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [orpsocv2/] [boards/] [xilinx/] [ml501/] [rtl/] [verilog/] [xilinx_ddr2/] [ddr2_ctrl.v] - Rev 480
Compare with Previous | Blame | View Log
//***************************************************************************** // DISCLAIMER OF LIABILITY // // This file contains proprietary and confidential information of // Xilinx, Inc. ("Xilinx"), that is distributed under a license // from Xilinx, and may be used, copied and/or disclosed only // pursuant to the terms of a valid license agreement with Xilinx. // // XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION // ("MATERIALS") "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER // EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING WITHOUT // LIMITATION, ANY WARRANTY WITH RESPECT TO NONINFRINGEMENT, // MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Xilinx // does not warrant that functions included in the Materials will // meet the requirements of Licensee, or that the operation of the // Materials will be uninterrupted or error-free, or that defects // in the Materials will be corrected. Furthermore, Xilinx does // not warrant or make any representations regarding use, or the // results of the use, of the Materials in terms of correctness, // accuracy, reliability or otherwise. // // Xilinx products are not designed or intended to be fail-safe, // or for use in any application requiring fail-safe performance, // such as life-support or safety devices or systems, Class III // medical devices, nuclear facilities, applications related to // the deployment of airbags, or any other applications that could // lead to death, personal injury or severe property or // environmental damage (individually and collectively, "critical // applications"). Customer assumes the sole risk and liability // of any use of Xilinx products in critical applications, // subject only to applicable laws and regulations governing // limitations on product liability. // // Copyright 2006, 2007, 2008 Xilinx, Inc. // All rights reserved. // // This disclaimer and copyright notice must be retained as part // of this file at all times. //***************************************************************************** // ____ ____ // / /\/ / // /___/ \ / Vendor: Xilinx // \ \ \/ Version: 3.0 // \ \ Application: MIG // / / Filename: ddr2_ctrl.v // /___/ /\ Date Last Modified: $Date: 2008/12/23 14:26:00 $ // \ \ / \ Date Created: Wed Aug 30 2006 // \___\/\___\ // // //Device: Virtex-5 //Design Name: DDR/DDR2 //Purpose: // This module is the main control logic of the memory interface. All // commands are issued from here according to the burst, CAS Latency and the // user commands. //Reference: //Revision History: // Rev 1.2 - Fixed auto refresh to activate bug. KP 11-19-2007 // Rev 1.3 - For Dual Rank parts support CS logic modified. KP. 05/08/08 // Rev 1.4 - AUTO_REFRESH_WAIT state modified for Auto Refresh flag asserted // immediately after calibration is completed. KP. 07/28/08 // Rev 1.5 - Assignment of bank_valid_r is modified to fix a bug in // Bank Management logic. PK. 10/29/08 //***************************************************************************** `timescale 1ns/1ps module ddr2_ctrl # ( // Following parameters are for 72-bit RDIMM design (for ML561 Reference // board design). Actual values may be different. Actual parameters values // are passed from design top module ddr2_mig module. Please refer to // the ddr2_mig module for actual values. parameter BANK_WIDTH = 2, parameter COL_WIDTH = 10, parameter CS_BITS = 0, parameter CS_NUM = 1, parameter ROW_WIDTH = 14, parameter ADDITIVE_LAT = 0, parameter BURST_LEN = 4, parameter CAS_LAT = 5, parameter ECC_ENABLE = 0, parameter REG_ENABLE = 1, parameter TREFI_NS = 7800, parameter TRAS = 40000, parameter TRCD = 15000, parameter TRRD = 10000, parameter TRFC = 105000, parameter TRP = 15000, parameter TRTP = 7500, parameter TWR = 15000, parameter TWTR = 10000, parameter CLK_PERIOD = 3000, parameter MULTI_BANK_EN = 1, parameter TWO_T_TIME_EN = 0, parameter DDR_TYPE = 1 ) ( input clk, input rst, input [2:0] af_cmd, input [30:0] af_addr, input af_empty, input phy_init_done, output ctrl_ref_flag, output ctrl_af_rden, output reg ctrl_wren, output reg ctrl_rden, output [ROW_WIDTH-1:0] ctrl_addr, output [BANK_WIDTH-1:0] ctrl_ba, output ctrl_ras_n, output ctrl_cas_n, output ctrl_we_n, output [CS_NUM-1:0] ctrl_cs_n ); // input address split into various ranges localparam ROW_RANGE_START = COL_WIDTH; localparam ROW_RANGE_END = ROW_WIDTH + ROW_RANGE_START - 1; localparam BANK_RANGE_START = ROW_RANGE_END + 1; localparam BANK_RANGE_END = BANK_WIDTH + BANK_RANGE_START - 1; localparam CS_RANGE_START = BANK_RANGE_START + BANK_WIDTH; localparam CS_RANGE_END = CS_BITS + CS_RANGE_START - 1; // compare address (for determining bank/row hits) split into various ranges // (compare address doesn't include column bits) localparam CMP_WIDTH = CS_BITS + BANK_WIDTH + ROW_WIDTH; localparam CMP_ROW_RANGE_START = 0; localparam CMP_ROW_RANGE_END = ROW_WIDTH + CMP_ROW_RANGE_START - 1; localparam CMP_BANK_RANGE_START = CMP_ROW_RANGE_END + 1; localparam CMP_BANK_RANGE_END = BANK_WIDTH + CMP_BANK_RANGE_START - 1; localparam CMP_CS_RANGE_START = CMP_BANK_RANGE_END + 1; localparam CMP_CS_RANGE_END = CS_BITS + CMP_CS_RANGE_START-1; localparam BURST_LEN_DIV2 = BURST_LEN / 2; localparam OPEN_BANK_NUM = 4; localparam CS_BITS_FIX = (CS_BITS == 0) ? 1 : CS_BITS; // calculation counters based on clock cycle and memory parameters // TRAS: ACTIVE->PRECHARGE interval - 2 localparam integer TRAS_CYC = (TRAS + CLK_PERIOD)/CLK_PERIOD; // TRCD: ACTIVE->READ/WRITE interval - 3 (for DDR2 factor in ADD_LAT) localparam integer TRRD_CYC = (TRRD + CLK_PERIOD)/CLK_PERIOD; localparam integer TRCD_CYC = (((TRCD + CLK_PERIOD)/CLK_PERIOD) > ADDITIVE_LAT )? ((TRCD+CLK_PERIOD)/ CLK_PERIOD) - ADDITIVE_LAT : 0; // TRFC: REFRESH->REFRESH, REFRESH->ACTIVE interval - 2 localparam integer TRFC_CYC = (TRFC + CLK_PERIOD)/CLK_PERIOD; // TRP: PRECHARGE->COMMAND interval - 2 // for precharge all add 1 extra clock cycle localparam integer TRP_CYC = ((TRP + CLK_PERIOD)/CLK_PERIOD) +1; // TRTP: READ->PRECHARGE interval - 2 (Al + BL/2 + (max (TRTP, 2tck))-2 localparam integer TRTP_TMP_MIN = (((TRTP + CLK_PERIOD)/CLK_PERIOD) >= 2)? ((TRTP + CLK_PERIOD)/CLK_PERIOD) : 2; localparam integer TRTP_CYC = TRTP_TMP_MIN + ADDITIVE_LAT + BURST_LEN_DIV2 - 2; // TWR: WRITE->PRECHARGE interval - 2 localparam integer WR_LAT = (DDR_TYPE > 0) ? CAS_LAT + ADDITIVE_LAT - 1 : 1; localparam integer TWR_CYC = ((TWR + CLK_PERIOD)/CLK_PERIOD) + WR_LAT + BURST_LEN_DIV2 ; // TWTR: WRITE->READ interval - 3 (for DDR1, TWTR = 2 clks) // DDR2 = CL-1 + BL/2 +TWTR localparam integer TWTR_TMP_MIN = (TWTR + CLK_PERIOD)/CLK_PERIOD; localparam integer TWTR_CYC = (DDR_TYPE > 0) ? (TWTR_TMP_MIN + (CAS_LAT -1) + BURST_LEN_DIV2 ): 2; // TRTW: READ->WRITE interval - 3 // DDR1: CL + (BL/2) // DDR2: (BL/2) + 2. Two more clocks are added to // the DDR2 counter to account for the delay in // arrival of the DQS during reads (pcb trace + buffer // delays + memory parameters). localparam TRTW_CYC = (DDR_TYPE > 0) ? BURST_LEN_DIV2 + 4 : (CAS_LAT == 25) ? 2 + BURST_LEN_DIV2 : CAS_LAT + BURST_LEN_DIV2; localparam integer CAS_LAT_RD = (CAS_LAT == 25) ? 2 : CAS_LAT; // Make sure all values >= 0 (some may be = 0) localparam TRAS_COUNT = (TRAS_CYC > 0) ? TRAS_CYC : 0; localparam TRCD_COUNT = (TRCD_CYC > 0) ? TRCD_CYC : 0; localparam TRRD_COUNT = (TRRD_CYC > 0) ? TRRD_CYC : 0; localparam TRFC_COUNT = (TRFC_CYC > 0) ? TRFC_CYC : 0; localparam TRP_COUNT = (TRP_CYC > 0) ? TRP_CYC : 0; localparam TRTP_COUNT = (TRTP_CYC > 0) ? TRTP_CYC : 0; localparam TWR_COUNT = (TWR_CYC > 0) ? TWR_CYC : 0; localparam TWTR_COUNT = (TWTR_CYC > 0) ? TWTR_CYC : 0; localparam TRTW_COUNT = (TRTW_CYC > 0) ? TRTW_CYC : 0; // Auto refresh interval localparam TREFI_COUNT = ((TREFI_NS * 1000)/CLK_PERIOD) - 1; // memory controller states localparam CTRL_IDLE = 5'h00; localparam CTRL_PRECHARGE = 5'h01; localparam CTRL_PRECHARGE_WAIT = 5'h02; localparam CTRL_AUTO_REFRESH = 5'h03; localparam CTRL_AUTO_REFRESH_WAIT = 5'h04; localparam CTRL_ACTIVE = 5'h05; localparam CTRL_ACTIVE_WAIT = 5'h06; localparam CTRL_BURST_READ = 5'h07; localparam CTRL_READ_WAIT = 5'h08; localparam CTRL_BURST_WRITE = 5'h09; localparam CTRL_WRITE_WAIT = 5'h0A; localparam CTRL_PRECHARGE_WAIT1 = 5'h0B; reg [CMP_WIDTH-1:0] act_addr_r; wire [30:0] af_addr_r; reg [30:0] af_addr_r1; reg [30:0] af_addr_r2; reg [30:0] af_addr_r3; wire [2:0] af_cmd_r; reg [2:0] af_cmd_r1; reg [2:0] af_cmd_r2; reg af_valid_r; reg af_valid_r1; reg af_valid_r2; reg [CS_BITS_FIX :0] auto_cnt_r; reg auto_ref_r; reg [(OPEN_BANK_NUM*CMP_WIDTH)-1:0] bank_cmp_addr_r; reg [OPEN_BANK_NUM-1:0] bank_hit; reg [OPEN_BANK_NUM-1:0] bank_hit_r; reg [OPEN_BANK_NUM-1:0] bank_hit_r1; reg [OPEN_BANK_NUM-1:0] bank_valid_r; reg bank_conflict_r; reg conflict_resolved_r; reg ctrl_af_rden_r; reg conflict_detect_r; wire conflict_detect; reg cs_change_r; reg cs_change_sticky_r; reg [ROW_WIDTH-1:0] ddr_addr_r; wire [ROW_WIDTH-1:0] ddr_addr_col; wire [ROW_WIDTH-1:0] ddr_addr_row; reg [BANK_WIDTH-1:0] ddr_ba_r; reg ddr_cas_n_r; reg [CS_NUM-1:0] ddr_cs_n_r; reg ddr_ras_n_r; reg ddr_we_n_r; reg [4:0] next_state; reg no_precharge_wait_r; reg no_precharge_r; reg no_precharge_r1; reg phy_init_done_r; reg [4:0] precharge_ok_cnt_r; reg precharge_ok_r; reg [4:0] ras_cnt_r; reg [3:0] rcd_cnt_r; reg rcd_cnt_ok_r; reg [2:0] rdburst_cnt_r; reg rdburst_ok_r; reg rdburst_rden_ok_r; reg rd_af_flag_r; wire rd_flag; reg rd_flag_r; reg [4:0] rd_to_wr_cnt_r; reg rd_to_wr_ok_r; reg ref_flag_r; reg [11:0] refi_cnt_r; reg refi_cnt_ok_r; reg rst_r /* synthesis syn_preserve = 1 */; reg rst_r1 /* synthesis syn_maxfan = 10 */; reg [7:0] rfc_cnt_r; reg rfc_ok_r; reg [3:0] row_miss; reg [3:0] row_conflict_r; reg [3:0] rp_cnt_r; reg rp_cnt_ok_r; reg [CMP_WIDTH-1:0] sb_open_add_r; reg [4:0] state_r; reg [4:0] state_r1; wire sm_rden; reg sm_rden_r; reg [2:0] trrd_cnt_r; reg trrd_cnt_ok_r; reg [2:0] two_t_enable_r; reg [CS_NUM-1:0] two_t_enable_r1; reg [2:0] wrburst_cnt_r; reg wrburst_ok_r; reg wrburst_wren_ok_r; wire wr_flag; reg wr_flag_r; reg [4:0] wr_to_rd_cnt_r; reg wr_to_rd_ok_r; // XST attributes for local reset "tree" // synthesis attribute shreg_extract of rst_r is "no"; // synthesis attribute shreg_extract of rst_r1 is "no"; // synthesis attribute equivalent_register_removal of rst_r is "no" //*************************************************************************** // sm_rden is used to assert read enable to the address FIFO assign sm_rden = ((state_r == CTRL_BURST_WRITE) || (state_r == CTRL_BURST_READ)) ; // Assert this when approaching refresh and not in an access reg ref_approaching; always @(posedge clk) ref_approaching <= (refi_cnt_r >= (TREFI_COUNT -80)) & ~af_valid_r2; reg ref_just_happened; always @(posedge clk) ref_just_happened <= (refi_cnt_r < 12'h30) & ~af_valid_r2; // assert read flag to the adress FIFO assign ctrl_af_rden = (sm_rden || rd_af_flag_r) & !(ref_approaching | ref_just_happened); // local reset "tree" for controller logic only. Create this to ease timing // on reset path. Prohibit equivalent register removal on RST_R to prevent // "sharing" with other local reset trees (caution: make sure global fanout // limit is set to large enough value, otherwise SLICES may be used for // fanout control on RST_R. always @(posedge clk) begin rst_r <= rst; rst_r1 <= rst_r; end //***************************************************************** // interpret commands from Command/Address FIFO //***************************************************************** assign wr_flag = (af_valid_r2) ? ((af_cmd_r2 == 3'b000) ? 1'b1 : 1'b0): 1'b0; assign rd_flag = (af_valid_r2) ? ((af_cmd_r2 == 3'b001) ? 1'b1 : 1'b0): 1'b0; always @(posedge clk) begin rd_flag_r <= rd_flag; wr_flag_r <= wr_flag; end ////////////////////////////////////////////////// // The data from the address FIFO is fetched and // stored in two register stages. The data will be // pulled out of the second register stage whenever // the state machine can handle new data from the // address FIFO. // This flag is asserted when there is no // cmd & address in the pipe. When there is // valid cmd & addr from the address FIFO the // af_valid signals will be asserted. This flag will // be set the cycle af_valid_r is de-asserted. always @(posedge clk) begin // for simulation purposes - to force CTRL_AF_RDEN low during reset if (rst_r1) rd_af_flag_r <= 1'd0; else if (rd_af_flag_r) // jb - probably should find a way // to stop this toggling all the time rd_af_flag_r <= 0; // jb else if((ctrl_af_rden_r) || (/*rd_af_flag_r &&*/ (af_valid_r || af_valid_r1))) // Fixed bug where third addresses would get lost (pulled off fifo and // then clobbered by other value later, thus ignored/skipped) - just // make sure we don't get too excited and pull too many off at once - jb rd_af_flag_r <= 1'd0; else if (~af_valid_r1 || ~af_valid_r) rd_af_flag_r <= 1'd1; end // always @ (posedge clk) // First register stage for the cmd & add from the FIFO. // The af_valid_r signal gives the status of the data // in this stage. The af_valid_r will be asserted when there // is valid data. This register stage will be updated // 1. read to the FIFO and the FIFO not empty // 2. After write and read states // 3. The valid signal is not asserted in the last stage. always @(posedge clk) begin if (rst_r1)begin af_valid_r <= 1'd0; end else begin if (ctrl_af_rden_r || sm_rden_r || ~af_valid_r1 || ~af_valid_r2)begin af_valid_r <= ctrl_af_rden_r; end end end // The output register in the FIFO is used. The addr // and command are already registered in the FIFO. assign af_addr_r = af_addr; assign af_cmd_r = af_cmd; // Second register stage for the cmd & add from the FIFO. // The af_valid_r1 signal gives the status of the data // in this stage. The af_valid_r will be asserted when there // is valid data. This register stage will be updated // 1. read to the FIFO and the FIFO not empty and there // is no valid data on this stage // 2. After write and read states // 3. The valid signal is not asserted in the last stage. always@(posedge clk) begin if (rst_r1)begin af_valid_r1 <= 1'd0; af_addr_r1 <= {31{1'bx}}; af_cmd_r1 <= {3{1'bx}}; end else if (~af_valid_r1 || sm_rden_r || ~af_valid_r2) begin af_valid_r1 <= af_valid_r; af_addr_r1 <= af_addr_r; af_cmd_r1 <= af_cmd_r; end end // The state machine uses the address and command in this // register stage. The data is fetched from the second // register stage whenever the state machine can accept new // addr. The conflict flags are also generated based on the // second register stage and updated when the new address // is loaded for the state machine. always@(posedge clk) begin if (rst_r1)begin af_valid_r2 <= 1'd0; af_addr_r2 <= {31{1'bx}}; af_cmd_r2 <= {3{1'bx}}; bank_hit_r <= {OPEN_BANK_NUM{1'bx}}; bank_conflict_r <= 1'bx; row_conflict_r <= 4'bx; end else if(sm_rden || ~af_valid_r2)begin af_valid_r2 <= af_valid_r1; af_addr_r2 <= af_addr_r1; af_cmd_r2 <= af_cmd_r1; if(MULTI_BANK_EN)begin bank_hit_r <= bank_hit; row_conflict_r <= row_miss; bank_conflict_r <= (~(|bank_hit)); end else begin bank_hit_r <= {OPEN_BANK_NUM{1'b0}}; bank_conflict_r <= 1'd0; row_conflict_r[0] <= (af_addr_r1[CS_RANGE_END:ROW_RANGE_START] != sb_open_add_r[CMP_WIDTH-1:0]); end end end // always@ (posedge clk) //detecting cs change for multi chip select case generate if(CS_NUM > 1) begin: gen_cs_change always @(posedge clk) begin if(sm_rden || ~af_valid_r2)begin cs_change_r <= af_addr_r1[CS_RANGE_END:CS_RANGE_START] != af_addr_r2[CS_RANGE_END:CS_RANGE_START] ; cs_change_sticky_r <= af_addr_r1[CS_RANGE_END:CS_RANGE_START] != af_addr_r2[CS_RANGE_END:CS_RANGE_START] ; end else cs_change_r <= 1'd0; end end // block: gen_cs_change else begin: gen_cs_0 always @(posedge clk) begin cs_change_r <= 1'd0; cs_change_sticky_r <= 1'd0; end end endgenerate assign conflict_detect = (MULTI_BANK_EN) ? ((|(row_conflict_r[3:0] & bank_hit_r[3:0])) | bank_conflict_r) & af_valid_r2 : row_conflict_r[0] & af_valid_r2; always @(posedge clk) begin conflict_detect_r <= conflict_detect; sm_rden_r <= sm_rden; af_addr_r3 <= af_addr_r2; ctrl_af_rden_r <= ctrl_af_rden & ~af_empty; end // conflict resolved signal. When this signal is asserted // the conflict is resolved. The address to be compared // for the conflict_resolved_r will be stored in act_add_r // when the bank is opened. always @(posedge clk) begin conflict_resolved_r <= (act_addr_r == af_addr_r2[CS_RANGE_END:ROW_RANGE_START]); if((state_r == CTRL_ACTIVE)) act_addr_r <= af_addr_r2[CS_RANGE_END:ROW_RANGE_START]; end //*************************************************************************** // Bank management logic // Semi-hardcoded for now for 4 banks // will keep multiple banks open if MULTI_BANK_EN is true. //*************************************************************************** genvar bank_i; generate // if multiple bank option chosen if(MULTI_BANK_EN) begin: gen_multi_bank_open for (bank_i = 0; bank_i < OPEN_BANK_NUM; bank_i = bank_i + 1) begin: gen_bank_hit1 // asserted if bank address match + open bank entry is valid always @(*) begin bank_hit[bank_i] = ((bank_cmp_addr_r[(CMP_WIDTH*(bank_i+1))-1: (CMP_WIDTH*bank_i)+ROW_WIDTH] == af_addr_r1[CS_RANGE_END:BANK_RANGE_START]) && bank_valid_r[bank_i]); // asserted if row address match (no check for bank entry valid, rely // on this term to be used in conjunction with BANK_HIT[]) row_miss[bank_i] = (bank_cmp_addr_r[(CMP_WIDTH*bank_i)+ROW_WIDTH-1: (CMP_WIDTH*bank_i)] != af_addr_r1[ROW_RANGE_END:ROW_RANGE_START]); end end always @(posedge clk) begin no_precharge_wait_r <= bank_valid_r[3] & bank_conflict_r; bank_hit_r1 <= bank_hit_r; end always@(*) no_precharge_r = ~bank_valid_r[3] & bank_conflict_r; always@(posedge clk) no_precharge_r1 <= no_precharge_r; always @(posedge clk) begin // Clear all bank valid bits during AR (i.e. since all banks get // precharged during auto-refresh) if ((state_r1 == CTRL_AUTO_REFRESH)) begin bank_valid_r <= {OPEN_BANK_NUM{1'b0}}; bank_cmp_addr_r <= {(OPEN_BANK_NUM*CMP_WIDTH-1){1'b0}}; end else begin if (state_r1 == CTRL_ACTIVE) begin // 00 is always going to have the latest bank and row. bank_cmp_addr_r[CMP_WIDTH-1:0] <= af_addr_r3[CS_RANGE_END:ROW_RANGE_START]; // This indicates the bank was activated bank_valid_r[0] <= 1'b1; case ({bank_hit_r1[2:0]}) 3'b001: begin bank_cmp_addr_r[CMP_WIDTH-1:0] <= af_addr_r3[CS_RANGE_END:ROW_RANGE_START]; // This indicates the bank was activated bank_valid_r[0] <= 1'b1; end 3'b010: begin //(b0->b1) bank_cmp_addr_r[(2*CMP_WIDTH)-1:CMP_WIDTH] <= bank_cmp_addr_r[CMP_WIDTH-1:0]; bank_valid_r[1] <= bank_valid_r[0]; end 3'b100:begin //(b0->b1, b1->b2) bank_cmp_addr_r[(2*CMP_WIDTH)-1:CMP_WIDTH] <= bank_cmp_addr_r[CMP_WIDTH-1:0]; bank_cmp_addr_r[(3*CMP_WIDTH)-1:2*CMP_WIDTH] <= bank_cmp_addr_r[(2*CMP_WIDTH)-1:CMP_WIDTH]; bank_valid_r[1] <= bank_valid_r[0]; bank_valid_r[2] <= bank_valid_r[1]; end default: begin //(b0->b1, b1->b2, b2->b3) bank_cmp_addr_r[(2*CMP_WIDTH)-1:CMP_WIDTH] <= bank_cmp_addr_r[CMP_WIDTH-1:0]; bank_cmp_addr_r[(3*CMP_WIDTH)-1:2*CMP_WIDTH] <= bank_cmp_addr_r[(2*CMP_WIDTH)-1:CMP_WIDTH]; bank_cmp_addr_r[(4*CMP_WIDTH)-1:3*CMP_WIDTH] <= bank_cmp_addr_r[(3*CMP_WIDTH)-1:2*CMP_WIDTH]; bank_valid_r[1] <= bank_valid_r[0]; bank_valid_r[2] <= bank_valid_r[1]; bank_valid_r[3] <= bank_valid_r[2]; end endcase end end end end else begin: gen_single_bank_open // single bank option always @(posedge clk) begin no_precharge_r <= 1'd0; no_precharge_r1 <= 1'd0; no_precharge_wait_r <= 1'd0; if (rst_r1) sb_open_add_r <= {CMP_WIDTH{1'b0}}; else if (state_r == CTRL_ACTIVE) sb_open_add_r <= af_addr_r2[CS_RANGE_END:ROW_RANGE_START]; end end endgenerate //*************************************************************************** // Timing counters //*************************************************************************** //***************************************************************** // Write and read enable generation for PHY //***************************************************************** // write burst count. Counts from (BL/2 to 1). // Also logic for controller write enable. always @(posedge clk) begin if (state_r == CTRL_BURST_WRITE) begin wrburst_cnt_r <= BURST_LEN_DIV2; end else if (wrburst_cnt_r >= 3'd1) wrburst_cnt_r <= wrburst_cnt_r - 1; end // always @ (posedge clk) always @(posedge clk) begin if (rst_r1) begin ctrl_wren <= 1'b0; end else if (state_r == CTRL_BURST_WRITE) begin ctrl_wren <= 1'b1; end else if (wrburst_wren_ok_r) ctrl_wren <= 1'b0; end always @(posedge clk) begin if ((state_r == CTRL_BURST_WRITE) && (BURST_LEN_DIV2 > 2)) wrburst_ok_r <= 1'd0; else if ((wrburst_cnt_r <= 3'd3) || (BURST_LEN_DIV2 <= 2)) wrburst_ok_r <= 1'b1; end // flag to check when wrburst count has reached // a value of 1. This flag is used in the ctrl_wren // logic always @(posedge clk) begin if(wrburst_cnt_r == 3'd2) wrburst_wren_ok_r <=1'b1; else wrburst_wren_ok_r <= 1'b0; end // read burst count. Counts from (BL/2 to 1) always @(posedge clk) begin if (state_r == CTRL_BURST_READ) begin rdburst_cnt_r <= BURST_LEN_DIV2; end else if (rdburst_cnt_r >= 3'd1) rdburst_cnt_r <= rdburst_cnt_r - 1; end // always @ (posedge clk) always @(posedge clk) begin if (rst_r1) begin ctrl_rden <= 1'b0; end else if (state_r == CTRL_BURST_READ) begin ctrl_rden <= 1'b1; end else if (rdburst_rden_ok_r) ctrl_rden <= 1'b0; end // the rd_burst_ok_r signal will be asserted one cycle later // in multi chip select cases if the back to back read is to // different chip selects. The cs_changed_sticky_r signal will // be asserted only for multi chip select cases. always @(posedge clk) begin if ((state_r == CTRL_BURST_READ) && (BURST_LEN_DIV2 > 2)) rdburst_ok_r <= 1'd0; else if ((rdburst_cnt_r <=( 3'd3 - cs_change_sticky_r)) || (BURST_LEN_DIV2 <= 2)) rdburst_ok_r <= 1'b1; end // flag to check when rdburst count has reached // a value of 1. This flag is used in the ctrl_rden // logic always @(posedge clk) begin if (rdburst_cnt_r == 3'd2) rdburst_rden_ok_r <= 1'b1; else rdburst_rden_ok_r <= 1'b0; end //***************************************************************** // Various delay counters // The counters are checked for value of <= 3 to determine the // if the count values are reached during different commands. // It is checked for 3 because // 1. The counters are loaded during the state when the command // state is reached (+1) // 2. After the <= 3 condition is reached the sm takes two cycles // to transition to the new command state (+2) //***************************************************************** // tRP count - precharge command period always @(posedge clk) begin if (state_r == CTRL_PRECHARGE) rp_cnt_r <= TRP_COUNT; else if (rp_cnt_r != 4'd0) rp_cnt_r <= rp_cnt_r - 1; end always @(posedge clk) begin if (state_r == CTRL_PRECHARGE) rp_cnt_ok_r <= 1'd0; else if (rp_cnt_r <= 4'd3) rp_cnt_ok_r <= 1'd1; end // tRFC count - refresh-refresh, refresh-active always @(posedge clk) begin if (state_r == CTRL_AUTO_REFRESH) rfc_cnt_r <= TRFC_COUNT; else if (rfc_cnt_r != 8'd0) rfc_cnt_r <= rfc_cnt_r - 1; end always @(posedge clk) begin if (state_r == CTRL_AUTO_REFRESH) rfc_ok_r <= 1'b0; else if(rfc_cnt_r <= 8'd3) rfc_ok_r <= 1'b1; end // tRCD count - active to read/write always @(posedge clk) begin if (state_r == CTRL_ACTIVE) rcd_cnt_r <= TRCD_COUNT; else if (rcd_cnt_r != 4'd0) rcd_cnt_r <= rcd_cnt_r - 1; end always @(posedge clk) begin if ((state_r == CTRL_ACTIVE) && (TRCD_COUNT > 2)) rcd_cnt_ok_r <= 1'd0; else if (rcd_cnt_r <= 4'd3) rcd_cnt_ok_r <= 1; end // tRRD count - active to active always @(posedge clk) begin if (state_r == CTRL_ACTIVE) trrd_cnt_r <= TRRD_COUNT; else if (trrd_cnt_r != 3'd0) trrd_cnt_r <= trrd_cnt_r - 1; end always @(posedge clk) begin if (state_r == CTRL_ACTIVE) trrd_cnt_ok_r <= 1'd0; else if (trrd_cnt_r <= 3'd3) trrd_cnt_ok_r <= 1; end // tRAS count - active to precharge always @(posedge clk) begin if (state_r == CTRL_ACTIVE) ras_cnt_r <= TRAS_COUNT; else if (ras_cnt_r != 5'd0) ras_cnt_r <= ras_cnt_r - 1; end // counter for write to prcharge // read to precharge and // activate to precharge // precharge_ok_cnt_r is added with trtp count, // there can be cases where the sm can go from // activate to read and the act->pre count time // would not have been satisfied. The rd->pre // time is very less. wr->pre time is almost the // same as act-> pre always @(posedge clk) begin if (state_r == CTRL_BURST_READ) begin // assign only if the cnt is < TRTP_COUNT if (precharge_ok_cnt_r < TRTP_COUNT) precharge_ok_cnt_r <= TRTP_COUNT; end else if (state_r == CTRL_BURST_WRITE) precharge_ok_cnt_r <= TWR_COUNT; else if (state_r == CTRL_ACTIVE) precharge_ok_cnt_r <= TRAS_COUNT; else if (precharge_ok_cnt_r != 5'd0) precharge_ok_cnt_r <= precharge_ok_cnt_r - 1; end always @(posedge clk) begin if ((state_r == CTRL_BURST_READ) || (state_r == CTRL_BURST_WRITE)|| (state_r == CTRL_ACTIVE)) precharge_ok_r <= 1'd0; else if(precharge_ok_cnt_r <= 5'd3) precharge_ok_r <=1'd1; end // write to read counter // write to read includes : write latency + burst time + tWTR always @(posedge clk) begin if (rst_r1) wr_to_rd_cnt_r <= 5'd0; else if (state_r == CTRL_BURST_WRITE) wr_to_rd_cnt_r <= (TWTR_COUNT); else if (wr_to_rd_cnt_r != 5'd0) wr_to_rd_cnt_r <= wr_to_rd_cnt_r - 1; end always @(posedge clk) begin if (state_r == CTRL_BURST_WRITE) wr_to_rd_ok_r <= 1'd0; else if (wr_to_rd_cnt_r <= 5'd3) wr_to_rd_ok_r <= 1'd1; end // read to write counter always @(posedge clk) begin if (rst_r1) rd_to_wr_cnt_r <= 5'd0; else if (state_r == CTRL_BURST_READ) rd_to_wr_cnt_r <= (TRTW_COUNT); else if (rd_to_wr_cnt_r != 5'd0) rd_to_wr_cnt_r <= rd_to_wr_cnt_r - 1; end always @(posedge clk) begin if (state_r == CTRL_BURST_READ) rd_to_wr_ok_r <= 1'b0; else if (rd_to_wr_cnt_r <= 5'd3) rd_to_wr_ok_r <= 1'b1; end always @(posedge clk) begin if(refi_cnt_r == (TREFI_COUNT -1)) refi_cnt_ok_r <= 1'b1; else refi_cnt_ok_r <= 1'b0; end // auto refresh interval counter in refresh_clk domain always @(posedge clk) begin if ((rst_r1) || (refi_cnt_ok_r)) begin refi_cnt_r <= 12'd0; end else begin refi_cnt_r <= refi_cnt_r + 1; end end // always @ (posedge clk) // auto refresh flag always @(posedge clk) begin if (refi_cnt_ok_r) begin ref_flag_r <= 1'b1; end else begin ref_flag_r <= 1'b0; end end // always @ (posedge clk) assign ctrl_ref_flag = ref_flag_r; //refresh flag detect //auto_ref high indicates auto_refresh requirement //auto_ref is held high until auto refresh command is issued. always @(posedge clk)begin if (rst_r1) auto_ref_r <= 1'b0; else if (ref_flag_r) auto_ref_r <= 1'b1; else if (state_r == CTRL_AUTO_REFRESH) auto_ref_r <= 1'b0; end // keep track of which chip selects got auto-refreshed (avoid auto-refreshing // all CS's at once to avoid current spike) always @(posedge clk)begin if (rst_r1 || (state_r1 == CTRL_PRECHARGE)) auto_cnt_r <= 'd0; else if (state_r1 == CTRL_AUTO_REFRESH) auto_cnt_r <= auto_cnt_r + 1; end // register for timing purposes. Extra delay doesn't really matter always @(posedge clk) phy_init_done_r <= phy_init_done; always @(posedge clk)begin if (rst_r1) begin state_r <= CTRL_IDLE; state_r1 <= CTRL_IDLE; end else begin state_r <= next_state; state_r1 <= state_r; end end //*************************************************************************** // main control state machine //*************************************************************************** always @(*) begin next_state = state_r; (* full_case, parallel_case *) case (state_r) CTRL_IDLE: begin // perform auto refresh as soon as we are done with calibration. // The calibration logic does not do any refreshes. if (phy_init_done_r) next_state = CTRL_AUTO_REFRESH; end CTRL_PRECHARGE: begin if (auto_ref_r) next_state = CTRL_PRECHARGE_WAIT1; // when precharging an LRU bank, do not have to go to wait state // since we can't possibly be activating row in same bank next // disabled for 2t timing. There needs to be a gap between cmds // in 2t timing else if (no_precharge_wait_r && !TWO_T_TIME_EN) next_state = CTRL_ACTIVE; else next_state = CTRL_PRECHARGE_WAIT; end CTRL_PRECHARGE_WAIT:begin if (rp_cnt_ok_r)begin if (auto_ref_r) // precharge again to make sure we close all the banks next_state = CTRL_PRECHARGE; else next_state = CTRL_ACTIVE; end end CTRL_PRECHARGE_WAIT1: if (rp_cnt_ok_r) next_state = CTRL_AUTO_REFRESH; CTRL_AUTO_REFRESH: next_state = CTRL_AUTO_REFRESH_WAIT; CTRL_AUTO_REFRESH_WAIT: //staggering Auto refresh for multi // chip select designs. The SM waits // for the rfc time before issuing the // next auto refresh. if (auto_cnt_r < (CS_NUM))begin if (rfc_ok_r ) next_state = CTRL_AUTO_REFRESH; end else if (rfc_ok_r)begin if(auto_ref_r) // MIG 2.3: For deep designs if Auto Refresh // flag asserted immediately after calibration is completed next_state = CTRL_PRECHARGE; else if ( wr_flag || rd_flag) next_state = CTRL_ACTIVE; end CTRL_ACTIVE: next_state = CTRL_ACTIVE_WAIT; CTRL_ACTIVE_WAIT: begin if (rcd_cnt_ok_r) begin if ((conflict_detect_r && ~conflict_resolved_r) || auto_ref_r) begin if (no_precharge_r1 && ~auto_ref_r && trrd_cnt_ok_r) next_state = CTRL_ACTIVE; else if(precharge_ok_r) next_state = CTRL_PRECHARGE; end else if ((wr_flag_r) && (rd_to_wr_ok_r)) next_state = CTRL_BURST_WRITE; else if ((rd_flag_r)&& (wr_to_rd_ok_r)) next_state = CTRL_BURST_READ; end end // beginning of write burst CTRL_BURST_WRITE: begin if (BURST_LEN_DIV2 == 1) begin // special case if BL = 2 (i.e. burst lasts only one clk cycle) if (wr_flag) // if we have another non-conflict write command right after the // current write, then stay in this state next_state = CTRL_BURST_WRITE; else // otherwise, if we're done with this burst, and have no write // immediately scheduled after this one, wait until write-read // delay has passed next_state = CTRL_WRITE_WAIT; end else // otherwise BL > 2, and we have at least one more write cycle for // current burst next_state = CTRL_WRITE_WAIT; // continuation of write burst (also covers waiting after write burst // has completed for write-read delay to pass) end CTRL_WRITE_WAIT: begin if ((conflict_detect) || auto_ref_r) begin if (no_precharge_r && ~auto_ref_r && wrburst_ok_r) next_state = CTRL_ACTIVE; else if (precharge_ok_r) next_state = CTRL_PRECHARGE; end else if (wrburst_ok_r && wr_flag) next_state = CTRL_BURST_WRITE; else if ((rd_flag) && (wr_to_rd_ok_r)) next_state = CTRL_BURST_READ; end CTRL_BURST_READ: begin if (BURST_LEN_DIV2 == 1) begin // special case if BL = 2 (i.e. burst lasts only one clk cycle) if (rd_flag) next_state = CTRL_BURST_READ; else next_state = CTRL_READ_WAIT; end else next_state = CTRL_READ_WAIT; end CTRL_READ_WAIT: begin if ((conflict_detect) || auto_ref_r)begin if (no_precharge_r && ~auto_ref_r && rdburst_ok_r) next_state = CTRL_ACTIVE; else if (precharge_ok_r) next_state = CTRL_PRECHARGE; // for burst of 4 in multi chip select // if there is a change in cs wait one cycle before the // next read command. cs_change_r will be asserted. end else if (rdburst_ok_r && rd_flag && ~cs_change_r) next_state = CTRL_BURST_READ; else if (wr_flag && (rd_to_wr_ok_r)) next_state = CTRL_BURST_WRITE; end endcase end //*************************************************************************** // control signals to memory //*************************************************************************** always @(posedge clk) begin if ((state_r == CTRL_AUTO_REFRESH) || (state_r == CTRL_ACTIVE) || (state_r == CTRL_PRECHARGE)) begin ddr_ras_n_r <= 1'b0; two_t_enable_r[0] <= 1'b0; end else begin if (TWO_T_TIME_EN) ddr_ras_n_r <= two_t_enable_r[0] ; else ddr_ras_n_r <= 1'd1; two_t_enable_r[0] <= 1'b1; end end always @(posedge clk)begin if ((state_r == CTRL_BURST_WRITE) || (state_r == CTRL_BURST_READ) || (state_r == CTRL_AUTO_REFRESH)) begin ddr_cas_n_r <= 1'b0; two_t_enable_r[1] <= 1'b0; end else begin if (TWO_T_TIME_EN) ddr_cas_n_r <= two_t_enable_r[1]; else ddr_cas_n_r <= 1'b1; two_t_enable_r[1] <= 1'b1; end end always @(posedge clk) begin if ((state_r == CTRL_BURST_WRITE) || (state_r == CTRL_PRECHARGE)) begin ddr_we_n_r <= 1'b0; two_t_enable_r[2] <= 1'b0; end else begin if(TWO_T_TIME_EN) ddr_we_n_r <= two_t_enable_r[2]; else ddr_we_n_r <= 1'b1; two_t_enable_r[2] <= 1'b1; end end // turn off auto-precharge when issuing commands (A10 = 0) // mapping the col add for linear addressing. generate if (TWO_T_TIME_EN) begin: gen_addr_col_two_t if (COL_WIDTH == ROW_WIDTH-1) begin: gen_ddr_addr_col_0 assign ddr_addr_col = {af_addr_r3[COL_WIDTH-1:10], 1'b0, af_addr_r3[9:0]}; end else begin if (COL_WIDTH > 10) begin: gen_ddr_addr_col_1 assign ddr_addr_col = {{(ROW_WIDTH-COL_WIDTH-1){1'b0}}, af_addr_r3[COL_WIDTH-1:10], 1'b0, af_addr_r3[9:0]}; end else begin: gen_ddr_addr_col_2 assign ddr_addr_col = {{(ROW_WIDTH-COL_WIDTH-1){1'b0}}, 1'b0, af_addr_r3[COL_WIDTH-1:0]}; end end end else begin: gen_addr_col_one_t if (COL_WIDTH == ROW_WIDTH-1) begin: gen_ddr_addr_col_0_1 assign ddr_addr_col = {af_addr_r2[COL_WIDTH-1:10], 1'b0, af_addr_r2[9:0]}; end else begin if (COL_WIDTH > 10) begin: gen_ddr_addr_col_1_1 assign ddr_addr_col = {{(ROW_WIDTH-COL_WIDTH-1){1'b0}}, af_addr_r2[COL_WIDTH-1:10], 1'b0, af_addr_r2[9:0]}; end else begin: gen_ddr_addr_col_2_1 assign ddr_addr_col = {{(ROW_WIDTH-COL_WIDTH-1){1'b0}}, 1'b0, af_addr_r2[COL_WIDTH-1:0]}; end end end endgenerate // Assign address during row activate generate if (TWO_T_TIME_EN) assign ddr_addr_row = af_addr_r3[ROW_RANGE_END:ROW_RANGE_START]; else assign ddr_addr_row = af_addr_r2[ROW_RANGE_END:ROW_RANGE_START]; endgenerate always @(posedge clk)begin if ((state_r == CTRL_ACTIVE) || ((state_r1 == CTRL_ACTIVE) && TWO_T_TIME_EN)) ddr_addr_r <= ddr_addr_row; else if ((state_r == CTRL_BURST_WRITE) || (state_r == CTRL_BURST_READ) || (((state_r1 == CTRL_BURST_WRITE) || (state_r1 == CTRL_BURST_READ)) && TWO_T_TIME_EN)) ddr_addr_r <= ddr_addr_col; else if (((state_r == CTRL_PRECHARGE) || ((state_r1 == CTRL_PRECHARGE) && TWO_T_TIME_EN)) && auto_ref_r) begin // if we're precharging as a result of AUTO-REFRESH, precharge all banks ddr_addr_r <= {ROW_WIDTH{1'b0}}; ddr_addr_r[10] <= 1'b1; end else if ((state_r == CTRL_PRECHARGE) || ((state_r1 == CTRL_PRECHARGE) && TWO_T_TIME_EN)) // if we're precharging to close a specific bank/row, set A10=0 ddr_addr_r <= {ROW_WIDTH{1'b0}}; else ddr_addr_r <= {ROW_WIDTH{1'bx}}; end always @(posedge clk)begin // whenever we're precharging, we're either: (1) precharging all banks (in // which case banks bits are don't care, (2) precharging the LRU bank, // b/c we've exceeded the limit of # of banks open (need to close the LRU // bank to make room for a new one), (3) we haven't exceed the maximum # // of banks open, but we trying to open a different row in a bank that's // already open if (((state_r == CTRL_PRECHARGE) || ((state_r1 == CTRL_PRECHARGE) && TWO_T_TIME_EN)) && bank_conflict_r && MULTI_BANK_EN) // When LRU bank needs to be closed ddr_ba_r <= bank_cmp_addr_r[(3*CMP_WIDTH)+CMP_BANK_RANGE_END: (3*CMP_WIDTH)+CMP_BANK_RANGE_START]; else begin // Either precharge due to refresh or bank hit case if (TWO_T_TIME_EN) ddr_ba_r <= af_addr_r3[BANK_RANGE_END:BANK_RANGE_START]; else ddr_ba_r <= af_addr_r2[BANK_RANGE_END:BANK_RANGE_START]; end end // chip enable generation logic generate // if only one chip select, always assert it after reset if (CS_BITS == 0) begin: gen_ddr_cs_0 always @(posedge clk) if (rst_r1) ddr_cs_n_r[0] <= 1'b1; else ddr_cs_n_r[0] <= 1'b0; // otherwise if we have multiple chip selects end else begin: gen_ddr_cs_1 if(TWO_T_TIME_EN) begin: gen_2t_cs always @(posedge clk) if (rst_r1) ddr_cs_n_r <= {CS_NUM{1'b1}}; else if ((state_r1 == CTRL_AUTO_REFRESH)) begin // if auto-refreshing, only auto-refresh one CS at any time (avoid // beating on the ground plane by refreshing all CS's at same time) ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[auto_cnt_r] <= 1'b0; end else if (auto_ref_r && (state_r1 == CTRL_PRECHARGE)) begin ddr_cs_n_r <= {CS_NUM{1'b0}}; end else if ((state_r1 == CTRL_PRECHARGE) && ( bank_conflict_r && MULTI_BANK_EN))begin // precharging the LRU bank ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[bank_cmp_addr_r[(3*CMP_WIDTH)+CMP_CS_RANGE_END: (3*CMP_WIDTH)+CMP_CS_RANGE_START]] <= 1'b0; end else begin // otherwise, check the upper address bits to see which CS to assert ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[af_addr_r3[CS_RANGE_END:CS_RANGE_START]] <= 1'b0; end // else: !if(((state_r == CTRL_PRECHARGE) ||... end else begin: gen_1t_cs // block: gen_2t_cs always @(posedge clk) if (rst_r1) ddr_cs_n_r <= {CS_NUM{1'b1}}; else if ((state_r == CTRL_AUTO_REFRESH) ) begin // if auto-refreshing, only auto-refresh one CS at any time (avoid // beating on the ground plane by refreshing all CS's at same time) ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[auto_cnt_r] <= 1'b0; end else if (auto_ref_r && (state_r == CTRL_PRECHARGE) ) begin ddr_cs_n_r <= {CS_NUM{1'b0}}; end else if ((state_r == CTRL_PRECHARGE) && (bank_conflict_r && MULTI_BANK_EN))begin // precharging the LRU bank ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[bank_cmp_addr_r[(3*CMP_WIDTH)+CMP_CS_RANGE_END: (3*CMP_WIDTH)+CMP_CS_RANGE_START]] <= 1'b0; end else begin // otherwise, check the upper address bits to see which CS to assert ddr_cs_n_r <= {CS_NUM{1'b1}}; ddr_cs_n_r[af_addr_r2[CS_RANGE_END:CS_RANGE_START]] <= 1'b0; end // else: !if(((state_r == CTRL_PRECHARGE) ||... end // block: gen_1t_cs end endgenerate // registring the two_t timing enable signal. // This signal will be asserted (low) when the // chip select has to be asserted. always @(posedge clk)begin if(&two_t_enable_r) two_t_enable_r1 <= {CS_NUM{1'b1}}; else two_t_enable_r1 <= {CS_NUM{1'b0}}; end assign ctrl_addr = ddr_addr_r; assign ctrl_ba = ddr_ba_r; assign ctrl_ras_n = ddr_ras_n_r; assign ctrl_cas_n = ddr_cas_n_r; assign ctrl_we_n = ddr_we_n_r; assign ctrl_cs_n = (TWO_T_TIME_EN) ? (ddr_cs_n_r | two_t_enable_r1) : ddr_cs_n_r; endmodule