URL
https://opencores.org/ocsvn/openrisc_me/openrisc_me/trunk
Subversion Repositories openrisc_me
[/] [openrisc/] [trunk/] [orpsocv2/] [boards/] [xilinx/] [ml501/] [rtl/] [verilog/] [xilinx_ddr2/] [ddr2_phy_init.v] - Rev 475
Go to most recent revision | Compare with Previous | Blame | View Log
//***************************************************************************** // DISCLAIMER OF LIABILITY // // This file contains proprietary and confidential information of // Xilinx, Inc. ("Xilinx"), that is distributed under a license // from Xilinx, and may be used, copied and/or disclosed only // pursuant to the terms of a valid license agreement with Xilinx. // // XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION // ("MATERIALS") "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER // EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING WITHOUT // LIMITATION, ANY WARRANTY WITH RESPECT TO NONINFRINGEMENT, // MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Xilinx // does not warrant that functions included in the Materials will // meet the requirements of Licensee, or that the operation of the // Materials will be uninterrupted or error-free, or that defects // in the Materials will be corrected. Furthermore, Xilinx does // not warrant or make any representations regarding use, or the // results of the use, of the Materials in terms of correctness, // accuracy, reliability or otherwise. // // Xilinx products are not designed or intended to be fail-safe, // or for use in any application requiring fail-safe performance, // such as life-support or safety devices or systems, Class III // medical devices, nuclear facilities, applications related to // the deployment of airbags, or any other applications that could // lead to death, personal injury or severe property or // environmental damage (individually and collectively, "critical // applications"). Customer assumes the sole risk and liability // of any use of Xilinx products in critical applications, // subject only to applicable laws and regulations governing // limitations on product liability. // // Copyright 2006, 2007, 2008 Xilinx, Inc. // All rights reserved. // // This disclaimer and copyright notice must be retained as part // of this file at all times. //***************************************************************************** // ____ ____ // / /\/ / // /___/ \ / Vendor: Xilinx // \ \ \/ Version: 3.0 // \ \ Application: MIG // / / Filename: ddr2_phy_init.v // /___/ /\ Date Last Modified: $Date: 2008/12/23 14:26:00 $ // \ \ / \ Date Created: Thu Aug 24 2006 // \___\/\___\ // //Device: Virtex-5 //Design Name: DDR2 //Purpose: //Reference: // This module is the intialization control logic of the memory interface. // All commands are issued from here acoording to the burst, CAS Latency and // the user commands. //Revision History: // Rev 1.1 - Localparam WR_RECOVERY added and mapped to // load mode register. PK. 14/7/08 // Rev 1.2 - To issue an Auto Refresh command to each chip during various // calibration stages logic modified. PK. 08/10/08 //***************************************************************************** `timescale 1ns/1ps module ddr2_phy_init # ( // Following parameters are for 72-bit RDIMM design (for ML561 Reference // board design). Actual values may be different. Actual parameters values // are passed from design top module ddr2_mig module. Please refer to // the ddr2_mig module for actual values. parameter BANK_WIDTH = 2, parameter CKE_WIDTH = 1, parameter COL_WIDTH = 10, parameter CS_BITS = 0, parameter CS_NUM = 1, parameter DQ_WIDTH = 72, parameter ODT_WIDTH = 1, parameter ROW_WIDTH = 14, parameter ADDITIVE_LAT = 0, parameter BURST_LEN = 4, parameter TWO_T_TIME_EN = 0, parameter BURST_TYPE = 0, parameter CAS_LAT = 5, parameter ODT_TYPE = 1, parameter REDUCE_DRV = 0, parameter REG_ENABLE = 1, parameter TWR = 15000, parameter CLK_PERIOD = 3000, parameter DDR_TYPE = 1, parameter SIM_ONLY = 0 ) ( input clk0, input clkdiv0, input rst0, input rstdiv0, input [3:0] calib_done, input ctrl_ref_flag, input calib_ref_req, output reg [3:0] calib_start, output reg calib_ref_done, output reg phy_init_wren, output reg phy_init_rden, output [ROW_WIDTH-1:0] phy_init_addr, output [BANK_WIDTH-1:0] phy_init_ba, output phy_init_ras_n, output phy_init_cas_n, output phy_init_we_n, output [CS_NUM-1:0] phy_init_cs_n, output [CKE_WIDTH-1:0] phy_init_cke, output reg phy_init_done, output phy_init_data_sel ); // time to wait between consecutive commands in PHY_INIT - this is a // generic number, and must be large enough to account for worst case // timing parameter (tRFC - refresh-to-active) across all memory speed // grades and operating frequencies. Expressed in CLKDIV clock cycles. localparam CNTNEXT_CMD = 7'b1111111; // time to wait between read and read or precharge for stage 3 & 4 // the larger CNTNEXT_CMD can also be used, use smaller number to // speed up calibration - avoid tRAS violation, and speeds up simulation localparam CNTNEXT_RD = 4'b1111; // Write recovery (WR) time - is defined by // tWR (in nanoseconds) by tCK (in nanoseconds) and rounding up a // noninteger value to the next integer localparam integer WR_RECOVERY = ((TWR + CLK_PERIOD) - 1)/CLK_PERIOD; localparam CS_BITS_FIX = (CS_BITS == 0) ? 1 : CS_BITS; localparam INIT_CAL1_READ = 5'h00; localparam INIT_CAL2_READ = 5'h01; localparam INIT_CAL3_READ = 5'h02; localparam INIT_CAL4_READ = 5'h03; localparam INIT_CAL1_WRITE = 5'h04; localparam INIT_CAL2_WRITE = 5'h05; localparam INIT_CAL3_WRITE = 5'h06; localparam INIT_DUMMY_ACTIVE_WAIT = 5'h07; localparam INIT_PRECHARGE = 5'h08; localparam INIT_LOAD_MODE = 5'h09; localparam INIT_AUTO_REFRESH = 5'h0A; localparam INIT_IDLE = 5'h0B; localparam INIT_CNT_200 = 5'h0C; localparam INIT_CNT_200_WAIT = 5'h0D; localparam INIT_PRECHARGE_WAIT = 5'h0E; localparam INIT_MODE_REGISTER_WAIT = 5'h0F; localparam INIT_AUTO_REFRESH_WAIT = 5'h10; localparam INIT_DEEP_MEMORY_ST = 5'h11; localparam INIT_DUMMY_ACTIVE = 5'h12; localparam INIT_CAL1_WRITE_READ = 5'h13; localparam INIT_CAL1_READ_WAIT = 5'h14; localparam INIT_CAL2_WRITE_READ = 5'h15; localparam INIT_CAL2_READ_WAIT = 5'h16; localparam INIT_CAL3_WRITE_READ = 5'h17; localparam INIT_CAL3_READ_WAIT = 5'h18; localparam INIT_CAL4_READ_WAIT = 5'h19; localparam INIT_CALIB_REF = 5'h1A; localparam INIT_ZQCL = 5'h1B; localparam INIT_WAIT_DLLK_ZQINIT = 5'h1C; localparam INIT_CNTR_INIT = 4'h0; localparam INIT_CNTR_PRECH_1 = 4'h1; localparam INIT_CNTR_EMR2_INIT = 4'h2; localparam INIT_CNTR_EMR3_INIT = 4'h3; localparam INIT_CNTR_EMR_EN_DLL = 4'h4; localparam INIT_CNTR_MR_RST_DLL = 4'h5; localparam INIT_CNTR_CNT_200_WAIT = 4'h6; localparam INIT_CNTR_PRECH_2 = 4'h7; localparam INIT_CNTR_AR_1 = 4'h8; localparam INIT_CNTR_AR_2 = 4'h9; localparam INIT_CNTR_MR_ACT_DLL = 4'hA; localparam INIT_CNTR_EMR_DEF_OCD = 4'hB; localparam INIT_CNTR_EMR_EXIT_OCD = 4'hC; localparam INIT_CNTR_DEEP_MEM = 4'hD; localparam INIT_CNTR_PRECH_3 = 4'hE; localparam INIT_CNTR_DONE = 4'hF; localparam DDR1 = 0; localparam DDR2 = 1; localparam DDR3 = 2; reg [CS_BITS_FIX :0] auto_cnt_r; reg [1:0] burst_addr_r; reg [1:0] burst_cnt_r; wire [1:0] burst_val; wire cal_read; wire cal_write; wire cal_write_read; reg cal1_started_r; reg cal2_started_r; reg cal4_started_r; reg [3:0] calib_done_r; reg calib_ref_req_posedge; reg calib_ref_req_r; reg [15:0] calib_start_shift0_r; reg [15:0] calib_start_shift1_r; reg [15:0] calib_start_shift2_r; reg [15:0] calib_start_shift3_r; reg [1:0] chip_cnt_r; reg [4:0] cke_200us_cnt_r; reg cke_200us_cnt_en_r; reg [7:0] cnt_200_cycle_r; reg cnt_200_cycle_done_r; reg [6:0] cnt_cmd_r; reg cnt_cmd_ok_r; reg [3:0] cnt_rd_r; reg cnt_rd_ok_r; reg ctrl_ref_flag_r; reg done_200us_r; reg [ROW_WIDTH-1:0] ddr_addr_r; reg [ROW_WIDTH-1:0] ddr_addr_r1; reg [BANK_WIDTH-1:0] ddr_ba_r; reg [BANK_WIDTH-1:0] ddr_ba_r1; reg ddr_cas_n_r; reg ddr_cas_n_r1; reg [CKE_WIDTH-1:0] ddr_cke_r; reg [CS_NUM-1:0] ddr_cs_n_r; reg [CS_NUM-1:0] ddr_cs_n_r1; reg [CS_NUM-1:0] ddr_cs_disable_r; reg ddr_ras_n_r; reg ddr_ras_n_r1; reg ddr_we_n_r; reg ddr_we_n_r1; wire [15:0] ext_mode_reg; reg [3:0] init_cnt_r; reg init_done_r; reg [4:0] init_next_state; reg [4:0] init_state_r; reg [4:0] init_state_r1; reg [4:0] init_state_r1_2t; reg [4:0] init_state_r2; wire [15:0] load_mode_reg; wire [15:0] load_mode_reg0; wire [15:0] load_mode_reg1; wire [15:0] load_mode_reg2; wire [15:0] load_mode_reg3; reg phy_init_done_r; reg phy_init_done_r1; reg phy_init_done_r2; reg phy_init_done_r3; reg refresh_req; wire [3:0] start_cal; //*************************************************************************** //***************************************************************** // DDR1 and DDR2 Load mode register // Mode Register (MR): // [15:14] - unused - 00 // [13] - reserved - 0 // [12] - Power-down mode - 0 (normal) // [11:9] - write recovery - for Auto Precharge (tWR/tCK) // [8] - DLL reset - 0 or 1 // [7] - Test Mode - 0 (normal) // [6:4] - CAS latency - CAS_LAT // [3] - Burst Type - BURST_TYPE // [2:0] - Burst Length - BURST_LEN //***************************************************************** generate if (DDR_TYPE == DDR2) begin: gen_load_mode_reg_ddr2 assign load_mode_reg[2:0] = (BURST_LEN == 8) ? 3'b011 : ((BURST_LEN == 4) ? 3'b010 : 3'b111); assign load_mode_reg[3] = BURST_TYPE; assign load_mode_reg[6:4] = (CAS_LAT == 3) ? 3'b011 : ((CAS_LAT == 4) ? 3'b100 : ((CAS_LAT == 5) ? 3'b101 : 3'b111)); assign load_mode_reg[7] = 1'b0; assign load_mode_reg[8] = 1'b0; // init value only (DLL not reset) assign load_mode_reg[11:9] = (WR_RECOVERY == 6) ? 3'b101 : ((WR_RECOVERY == 5) ? 3'b100 : ((WR_RECOVERY == 4) ? 3'b011 : ((WR_RECOVERY == 3) ? 3'b010 : 3'b001))); assign load_mode_reg[15:12] = 4'b000; end else if (DDR_TYPE == DDR1)begin: gen_load_mode_reg_ddr1 assign load_mode_reg[2:0] = (BURST_LEN == 8) ? 3'b011 : ((BURST_LEN == 4) ? 3'b010 : ((BURST_LEN == 2) ? 3'b001 : 3'b111)); assign load_mode_reg[3] = BURST_TYPE; assign load_mode_reg[6:4] = (CAS_LAT == 2) ? 3'b010 : ((CAS_LAT == 3) ? 3'b011 : ((CAS_LAT == 25) ? 3'b110 : 3'b111)); assign load_mode_reg[12:7] = 6'b000000; // init value only assign load_mode_reg[15:13] = 3'b000; end endgenerate //***************************************************************** // DDR1 and DDR2 ext mode register // Extended Mode Register (MR): // [15:14] - unused - 00 // [13] - reserved - 0 // [12] - output enable - 0 (enabled) // [11] - RDQS enable - 0 (disabled) // [10] - DQS# enable - 0 (enabled) // [9:7] - OCD Program - 111 or 000 (first 111, then 000 during init) // [6] - RTT[1] - RTT[1:0] = 0(no ODT), 1(75), 2(150), 3(50) // [5:3] - Additive CAS - ADDITIVE_CAS // [2] - RTT[0] // [1] - Output drive - REDUCE_DRV (= 0(full), = 1 (reduced) // [0] - DLL enable - 0 (normal) //***************************************************************** generate if (DDR_TYPE == DDR2) begin: gen_ext_mode_reg_ddr2 assign ext_mode_reg[0] = 1'b0; assign ext_mode_reg[1] = REDUCE_DRV; assign ext_mode_reg[2] = ((ODT_TYPE == 1) || (ODT_TYPE == 3)) ? 1'b1 : 1'b0; assign ext_mode_reg[5:3] = (ADDITIVE_LAT == 0) ? 3'b000 : ((ADDITIVE_LAT == 1) ? 3'b001 : ((ADDITIVE_LAT == 2) ? 3'b010 : ((ADDITIVE_LAT == 3) ? 3'b011 : ((ADDITIVE_LAT == 4) ? 3'b100 : 3'b111)))); assign ext_mode_reg[6] = ((ODT_TYPE == 2) || (ODT_TYPE == 3)) ? 1'b1 : 1'b0; assign ext_mode_reg[9:7] = 3'b000; assign ext_mode_reg[10] = 1'b0; assign ext_mode_reg[15:10] = 6'b000000; end else if (DDR_TYPE == DDR1)begin: gen_ext_mode_reg_ddr1 assign ext_mode_reg[0] = 1'b0; assign ext_mode_reg[1] = REDUCE_DRV; assign ext_mode_reg[12:2] = 11'b00000000000; assign ext_mode_reg[15:13] = 3'b000; end endgenerate //***************************************************************** // DDR3 Load mode reg0 // Mode Register (MR0): // [15:13] - unused - 000 // [12] - Precharge Power-down DLL usage - 0 (DLL frozen, slow-exit), // 1 (DLL maintained) // [11:9] - write recovery for Auto Precharge (tWR/tCK = 6) // [8] - DLL reset - 0 or 1 // [7] - Test Mode - 0 (normal) // [6:4],[2] - CAS latency - CAS_LAT // [3] - Burst Type - BURST_TYPE // [1:0] - Burst Length - BURST_LEN //***************************************************************** generate if (DDR_TYPE == DDR3) begin: gen_load_mode_reg0_ddr3 assign load_mode_reg0[1:0] = (BURST_LEN == 8) ? 2'b00 : ((BURST_LEN == 4) ? 2'b10 : 2'b11); // Part of CAS latency. This bit is '0' for all CAS latencies assign load_mode_reg0[2] = 1'b0; assign load_mode_reg0[3] = BURST_TYPE; assign load_mode_reg0[6:4] = (CAS_LAT == 5) ? 3'b001 : (CAS_LAT == 6) ? 3'b010 : 3'b111; assign load_mode_reg0[7] = 1'b0; // init value only (DLL reset) assign load_mode_reg0[8] = 1'b1; assign load_mode_reg0[11:9] = 3'b010; // Precharge Power-Down DLL 'slow-exit' assign load_mode_reg0[12] = 1'b0; assign load_mode_reg0[15:13] = 3'b000; end endgenerate //***************************************************************** // DDR3 Load mode reg1 // Mode Register (MR1): // [15:13] - unused - 00 // [12] - output enable - 0 (enabled for DQ, DQS, DQS#) // [11] - TDQS enable - 0 (TDQS disabled and DM enabled) // [10] - reserved - 0 (must be '0') // [9] - RTT[2] - 0 // [8] - reserved - 0 (must be '0') // [7] - write leveling - 0 (disabled), 1 (enabled) // [6] - RTT[1] - RTT[1:0] = 0(no ODT), 1(75), 2(150), 3(50) // [5] - Output driver impedance[1] - 0 (RZQ/6 and RZQ/7) // [4:3] - Additive CAS - ADDITIVE_CAS // [2] - RTT[0] // [1] - Output driver impedance[0] - 0(RZQ/6), or 1 (RZQ/7) // [0] - DLL enable - 0 (normal) //***************************************************************** generate if (DDR_TYPE == DDR3) begin: gen_ext_mode_reg1_ddr3 // DLL enabled during Imitialization assign load_mode_reg1[0] = 1'b0; // RZQ/6 assign load_mode_reg1[1] = REDUCE_DRV; assign load_mode_reg1[2] = ((ODT_TYPE == 1) || (ODT_TYPE == 3)) ? 1'b1 : 1'b0; assign load_mode_reg1[4:3] = (ADDITIVE_LAT == 0) ? 2'b00 : ((ADDITIVE_LAT == 1) ? 2'b01 : ((ADDITIVE_LAT == 2) ? 2'b10 : 3'b111)); // RZQ/6 assign load_mode_reg1[5] = 1'b0; assign load_mode_reg1[6] = ((ODT_TYPE == 2) || (ODT_TYPE == 3)) ? 1'b1 : 1'b0; // Make zero WRITE_LEVEL assign load_mode_reg1[7] = 0; assign load_mode_reg1[8] = 1'b0; assign load_mode_reg1[9] = 1'b0; assign load_mode_reg1[10] = 1'b0; assign load_mode_reg1[15:11] = 5'b00000; end endgenerate //***************************************************************** // DDR3 Load mode reg2 // Mode Register (MR2): // [15:11] - unused - 00 // [10:9] - RTT_WR - 00 (Dynamic ODT off) // [8] - reserved - 0 (must be '0') // [7] - self-refresh temperature range - // 0 (normal), 1 (extended) // [6] - Auto Self-Refresh - 0 (manual), 1(auto) // [5:3] - CAS Write Latency (CWL) - // 000 (5 for 400 MHz device), // 001 (6 for 400 MHz to 533 MHz devices), // 010 (7 for 533 MHz to 667 MHz devices), // 011 (8 for 667 MHz to 800 MHz) // [2:0] - Partial Array Self-Refresh (Optional) - // 000 (full array) //***************************************************************** generate if (DDR_TYPE == DDR3) begin: gen_ext_mode_reg2_ddr3 assign load_mode_reg2[2:0] = 3'b000; assign load_mode_reg2[5:3] = (CAS_LAT == 5) ? 3'b000 : (CAS_LAT == 6) ? 3'b001 : 3'b111; assign load_mode_reg2[6] = 1'b0; // Manual Self-Refresh assign load_mode_reg2[7] = 1'b0; assign load_mode_reg2[8] = 1'b0; assign load_mode_reg2[10:9] = 2'b00; assign load_mode_reg2[15:11] = 5'b00000; end endgenerate //***************************************************************** // DDR3 Load mode reg3 // Mode Register (MR3): // [15:3] - unused - All zeros // [2] - MPR Operation - 0(normal operation), 1(data flow from MPR) // [1:0] - MPR location - 00 (Predefined pattern) //***************************************************************** generate if (DDR_TYPE == DDR3)begin: gen_ext_mode_reg3_ddr3 assign load_mode_reg3[1:0] = 2'b00; assign load_mode_reg3[2] = 1'b0; assign load_mode_reg3[15:3] = 13'b0000000000000; end endgenerate //*************************************************************************** // Logic for calibration start, and for auto-refresh during cal request // CALIB_REF_REQ is used by calibration logic to request auto-refresh // durign calibration (used to avoid tRAS violation is certain calibration // stages take a long time). Once the auto-refresh is complete and cal can // be resumed, CALIB_REF_DONE is asserted by PHY_INIT. //*************************************************************************** // generate pulse for each of calibration start controls assign start_cal[0] = ((init_state_r1 == INIT_CAL1_READ) && (init_state_r2 != INIT_CAL1_READ)); assign start_cal[1] = ((init_state_r1 == INIT_CAL2_READ) && (init_state_r2 != INIT_CAL2_READ)); assign start_cal[2] = ((init_state_r1 == INIT_CAL3_READ) && (init_state_r2 == INIT_CAL3_WRITE_READ)); assign start_cal[3] = ((init_state_r1 == INIT_CAL4_READ) && (init_state_r2 == INIT_DUMMY_ACTIVE_WAIT)); // Generate positive-edge triggered, latched signal to force initialization // to pause calibration, and to issue auto-refresh. Clear flag as soon as // refresh initiated always @(posedge clkdiv0) if (rstdiv0) begin calib_ref_req_r <= 1'b0; calib_ref_req_posedge <= 1'b0; refresh_req <= 1'b0; end else begin calib_ref_req_r <= calib_ref_req; calib_ref_req_posedge <= calib_ref_req & ~calib_ref_req_r; if (init_state_r1 == INIT_AUTO_REFRESH) refresh_req <= 1'b0; else if (calib_ref_req_posedge) refresh_req <= 1'b1; end // flag to tell cal1 calibration was started. // This flag is used for cal1 auto refreshes // some of these bits may not be needed - only needed for those stages that // need refreshes within the stage (i.e. very long stages) always @(posedge clkdiv0) if (rstdiv0) begin cal1_started_r <= 1'b0; cal2_started_r <= 1'b0; cal4_started_r <= 1'b0; end else begin if (calib_start[0]) cal1_started_r <= 1'b1; if (calib_start[1]) cal2_started_r <= 1'b1; if (calib_start[3]) cal4_started_r <= 1'b1; end // Delay start of each calibration by 16 clock cycles to // ensure that when calibration logic begins, that read data is already // appearing on the bus. Don't really need it, it's more for simulation // purposes. Each circuit should synthesize using an SRL16. // In first stage of calibration periodic auto refreshes // will be issued to meet memory timing. calib_start_shift0_r[15] will be // asserted more than once.calib_start[0] is anded with cal1_started_r so // that it is asserted only once. cal1_refresh_done is anded with // cal1_started_r so that it is asserted after the auto refreshes. always @(posedge clkdiv0) begin calib_start_shift0_r <= {calib_start_shift0_r[14:0], start_cal[0]}; calib_start_shift1_r <= {calib_start_shift1_r[14:0], start_cal[1]}; calib_start_shift2_r <= {calib_start_shift2_r[14:0], start_cal[2]}; calib_start_shift3_r <= {calib_start_shift3_r[14:0], start_cal[3]}; calib_start[0] <= calib_start_shift0_r[15] & ~cal1_started_r; calib_start[1] <= calib_start_shift1_r[15] & ~cal2_started_r; calib_start[2] <= calib_start_shift2_r[15]; calib_start[3] <= calib_start_shift3_r[15] & ~cal4_started_r; calib_ref_done <= calib_start_shift0_r[15] | calib_start_shift1_r[15] | calib_start_shift3_r[15]; end // generate delay for various states that require it (no maximum delay // requirement, make sure that terminal count is large enough to cover // all cases) always @(posedge clkdiv0) begin case (init_state_r) INIT_PRECHARGE_WAIT, INIT_MODE_REGISTER_WAIT, INIT_AUTO_REFRESH_WAIT, INIT_DUMMY_ACTIVE_WAIT, INIT_CAL1_WRITE_READ, INIT_CAL1_READ_WAIT, INIT_CAL2_WRITE_READ, INIT_CAL2_READ_WAIT, INIT_CAL3_WRITE_READ: cnt_cmd_r <= cnt_cmd_r + 1; default: cnt_cmd_r <= 7'b0000000; endcase end // assert when count reaches the value always @(posedge clkdiv0) begin if(cnt_cmd_r == CNTNEXT_CMD) cnt_cmd_ok_r <= 1'b1; else cnt_cmd_ok_r <= 1'b0; end always @(posedge clkdiv0) begin case (init_state_r) INIT_CAL3_READ_WAIT, INIT_CAL4_READ_WAIT: cnt_rd_r <= cnt_rd_r + 1; default: cnt_rd_r <= 4'b0000; endcase end always @(posedge clkdiv0) begin if(cnt_rd_r == CNTNEXT_RD) cnt_rd_ok_r <= 1'b1; else cnt_rd_ok_r <= 1'b0; end //*************************************************************************** // Initial delay after power-on //*************************************************************************** // register the refresh flag from the controller. // The refresh flag is in full frequency domain - so a pulsed version must // be generated for half freq domain using 2 consecutive full clk cycles // The registered version is used for the 200us counter always @(posedge clk0) ctrl_ref_flag_r <= ctrl_ref_flag; always @(posedge clkdiv0) cke_200us_cnt_en_r <= ctrl_ref_flag || ctrl_ref_flag_r; // 200us counter for cke always @(posedge clkdiv0) if (rstdiv0) begin // skip power-up count if only simulating if (SIM_ONLY) cke_200us_cnt_r <= 5'b00001; else cke_200us_cnt_r <= 5'd27; end else if (cke_200us_cnt_en_r) cke_200us_cnt_r <= cke_200us_cnt_r - 1; always @(posedge clkdiv0) if (rstdiv0) done_200us_r <= 1'b0; else if (!done_200us_r) done_200us_r <= (cke_200us_cnt_r == 5'b00000); // 200 clocks counter - count value : h'64 required for initialization // Counts 100 divided by two clocks always @(posedge clkdiv0) if (rstdiv0 || (init_state_r == INIT_CNT_200)) cnt_200_cycle_r <= 8'h64; else if (init_state_r == INIT_ZQCL) // ddr3 cnt_200_cycle_r <= 8'hC8; else if (cnt_200_cycle_r != 8'h00) cnt_200_cycle_r <= cnt_200_cycle_r - 1; always @(posedge clkdiv0) if (rstdiv0 || (init_state_r == INIT_CNT_200) || (init_state_r == INIT_ZQCL)) cnt_200_cycle_done_r <= 1'b0; else if (cnt_200_cycle_r == 8'h00) cnt_200_cycle_done_r <= 1'b1; //***************************************************************** // handle deep memory configuration: // During initialization: Repeat initialization sequence once for each // chip select. Note that we could perform initalization for all chip // selects simulataneously. Probably fine - any potential SI issues with // auto refreshing all chip selects at once? // Once initialization complete, assert only CS[1] for calibration. //***************************************************************** always @(posedge clkdiv0) if (rstdiv0) begin chip_cnt_r <= 2'b00; end else if (init_state_r == INIT_DEEP_MEMORY_ST) begin if (chip_cnt_r != CS_NUM) chip_cnt_r <= chip_cnt_r + 1; else chip_cnt_r <= 2'b00; // MIG 2.4: Modified to issue an Auto Refresh commmand // to each chip select during various calibration stages end else if (init_state_r == INIT_PRECHARGE && init_done_r) begin chip_cnt_r <= 2'b00; end else if (init_state_r1 == INIT_AUTO_REFRESH && init_done_r) begin if (chip_cnt_r < (CS_NUM-1)) chip_cnt_r <= chip_cnt_r + 1; end // keep track of which chip selects got auto-refreshed (avoid auto-refreshing // all CS's at once to avoid current spike) always @(posedge clkdiv0)begin if (rstdiv0 || init_state_r == INIT_PRECHARGE) auto_cnt_r <= 'd0; else if (init_state_r == INIT_AUTO_REFRESH && init_done_r) begin if (auto_cnt_r < CS_NUM) auto_cnt_r <= auto_cnt_r + 1; end end always @(posedge clkdiv0) if (rstdiv0) begin ddr_cs_n_r <= {CS_NUM{1'b1}}; end else begin ddr_cs_n_r <= {CS_NUM{1'b1}}; if ((init_state_r == INIT_DUMMY_ACTIVE) || ((init_state_r == INIT_PRECHARGE) && (~init_done_r))|| (init_state_r == INIT_LOAD_MODE) || (init_state_r == INIT_AUTO_REFRESH) || (init_state_r == INIT_ZQCL ) || (((init_state_r == INIT_CAL1_READ) || (init_state_r == INIT_CAL2_READ) || (init_state_r == INIT_CAL3_READ) || (init_state_r == INIT_CAL4_READ) || (init_state_r == INIT_CAL1_WRITE) || (init_state_r == INIT_CAL2_WRITE) || (init_state_r == INIT_CAL3_WRITE)) && (burst_cnt_r == 2'b00))) ddr_cs_n_r[chip_cnt_r] <= 1'b0; else if (init_state_r == INIT_PRECHARGE) ddr_cs_n_r <= {CS_NUM{1'b0}}; else ddr_cs_n_r[chip_cnt_r] <= 1'b1; end //*************************************************************************** // Write/read burst logic //*************************************************************************** assign cal_write = ((init_state_r == INIT_CAL1_WRITE) || (init_state_r == INIT_CAL2_WRITE) || (init_state_r == INIT_CAL3_WRITE)); assign cal_read = ((init_state_r == INIT_CAL1_READ) || (init_state_r == INIT_CAL2_READ) || (init_state_r == INIT_CAL3_READ) || (init_state_r == INIT_CAL4_READ)); assign cal_write_read = ((init_state_r == INIT_CAL1_READ) || (init_state_r == INIT_CAL2_READ) || (init_state_r == INIT_CAL3_READ) || (init_state_r == INIT_CAL4_READ) || (init_state_r == INIT_CAL1_WRITE) || (init_state_r == INIT_CAL2_WRITE) || (init_state_r == INIT_CAL3_WRITE)); assign burst_val = (BURST_LEN == 4) ? 2'b00 : (BURST_LEN == 8) ? 2'b01 : 2'b00; // keep track of current address - need this if burst length < 8 for // stage 2-4 calibration writes and reads. Make sure value always gets // initialized to 0 before we enter write/read state. This is used to // keep track of when another burst must be issued always @(posedge clkdiv0) if (cal_write_read) burst_addr_r <= burst_addr_r + 2; else burst_addr_r <= 2'b00; // write/read burst count always @(posedge clkdiv0) if (cal_write_read) if (burst_cnt_r == 2'b00) burst_cnt_r <= burst_val; else // SHOULD THIS BE -2 CHECK THIS LOGIC burst_cnt_r <= burst_cnt_r - 1; else burst_cnt_r <= 2'b00; // indicate when a write is occurring always @(posedge clkdiv0) // MIG 2.1: Remove (burst_addr_r<4) term - not used // phy_init_wren <= cal_write && (burst_addr_r < 3'd4); phy_init_wren <= cal_write; // used for read enable calibration, pulse to indicate when read issued always @(posedge clkdiv0) // MIG 2.1: Remove (burst_addr_r<4) term - not used // phy_init_rden <= cal_read && (burst_addr_r < 3'd4); phy_init_rden <= cal_read; //*************************************************************************** // Initialization state machine //*************************************************************************** always @(posedge clkdiv0) // every time we need to initialize another rank of memory, need to // reset init count, and repeat the entire initialization (but not // calibration) sequence if (rstdiv0 || (init_state_r == INIT_DEEP_MEMORY_ST)) init_cnt_r <= INIT_CNTR_INIT; else if ((DDR_TYPE == DDR1) && (init_state_r == INIT_PRECHARGE) && (init_cnt_r == INIT_CNTR_PRECH_1)) // skip EMR(2) and EMR(3) register loads init_cnt_r <= INIT_CNTR_EMR_EN_DLL; else if ((DDR_TYPE == DDR1) && (init_state_r == INIT_LOAD_MODE) && (init_cnt_r == INIT_CNTR_MR_ACT_DLL)) // skip OCD calibration for DDR1 init_cnt_r <= INIT_CNTR_DEEP_MEM; else if ((DDR_TYPE == DDR3) && (init_state_r == INIT_ZQCL)) // skip states for DDR3 init_cnt_r <= INIT_CNTR_DEEP_MEM; else if ((init_state_r == INIT_LOAD_MODE) || ((init_state_r == INIT_PRECHARGE) && (init_state_r1 != INIT_CALIB_REF))|| ((init_state_r == INIT_AUTO_REFRESH) && (~init_done_r))|| (init_state_r == INIT_CNT_200)) init_cnt_r <= init_cnt_r + 1; always @(posedge clkdiv0) begin if ((init_state_r == INIT_IDLE) && (init_cnt_r == INIT_CNTR_DONE)) begin phy_init_done_r <= 1'b1; end else phy_init_done_r <= 1'b0; end // phy_init_done to the controller and the user interface. // It is delayed by four clocks to account for the // multi cycle path constraint to the (phy_init_data_sel) // to the phy layer. always @(posedge clkdiv0)begin phy_init_done_r1 <= phy_init_done_r; phy_init_done_r2 <= phy_init_done_r1; phy_init_done_r3 <= phy_init_done_r2; phy_init_done <= phy_init_done_r3; end // Instantiate primitive to allow this flop to be attached to multicycle // path constraint in UCF. This signal goes to PHY_WRITE and PHY_CTL_IO // datapath logic only. Because it is a multi-cycle path, it can be // clocked by either CLKDIV0 or CLK0. FDRSE u_ff_phy_init_data_sel ( .Q (phy_init_data_sel), .C (clkdiv0), .CE (1'b1), .D (phy_init_done_r1), .R (1'b0), .S (1'b0) ) /* synthesis syn_preserve=1 */ /* synthesis syn_replicate = 0 */; //synthesis translate_off always @(posedge calib_done[0]) $display ("First Stage Calibration completed at time %t", $time); always @(posedge calib_done[1]) $display ("Second Stage Calibration completed at time %t", $time); always @(posedge calib_done[2]) begin $display ("Third Stage Calibration completed at time %t", $time); end always @(posedge calib_done[3]) begin $display ("Fourth Stage Calibration completed at time %t", $time); $display ("Calibration completed at time %t", $time); end //synthesis translate_on always @(posedge clkdiv0) begin if ((init_cnt_r >= INIT_CNTR_DEEP_MEM))begin init_done_r <= 1'b1; end else init_done_r <= 1'b0; end //***************************************************************** always @(posedge clkdiv0) if (rstdiv0) begin init_state_r <= INIT_IDLE; init_state_r1 <= INIT_IDLE; init_state_r2 <= INIT_IDLE; calib_done_r <= 4'b0000; end else begin init_state_r <= init_next_state; init_state_r1 <= init_state_r; init_state_r2 <= init_state_r1; calib_done_r <= calib_done; // register for timing end always @(*) begin init_next_state = init_state_r; (* full_case, parallel_case *) case (init_state_r) INIT_IDLE: begin if (done_200us_r) begin (* parallel_case *) case (init_cnt_r) INIT_CNTR_INIT: init_next_state = INIT_CNT_200; INIT_CNTR_PRECH_1: init_next_state = INIT_PRECHARGE; INIT_CNTR_EMR2_INIT: init_next_state = INIT_LOAD_MODE; // EMR(2) INIT_CNTR_EMR3_INIT: init_next_state = INIT_LOAD_MODE; // EMR(3); INIT_CNTR_EMR_EN_DLL: init_next_state = INIT_LOAD_MODE; // EMR, enable DLL INIT_CNTR_MR_RST_DLL: init_next_state = INIT_LOAD_MODE; // MR, reset DLL INIT_CNTR_CNT_200_WAIT:begin if(DDR_TYPE == DDR3) init_next_state = INIT_ZQCL; // DDR3 else // Wait 200cc after reset DLL init_next_state = INIT_CNT_200; end INIT_CNTR_PRECH_2: init_next_state = INIT_PRECHARGE; INIT_CNTR_AR_1: init_next_state = INIT_AUTO_REFRESH; INIT_CNTR_AR_2: init_next_state = INIT_AUTO_REFRESH; INIT_CNTR_MR_ACT_DLL: init_next_state = INIT_LOAD_MODE; // MR, unreset DLL INIT_CNTR_EMR_DEF_OCD: init_next_state = INIT_LOAD_MODE; // EMR, OCD default INIT_CNTR_EMR_EXIT_OCD: init_next_state = INIT_LOAD_MODE; // EMR, enable OCD exit INIT_CNTR_DEEP_MEM: begin if ((chip_cnt_r < CS_NUM-1)) init_next_state = INIT_DEEP_MEMORY_ST; else if (cnt_200_cycle_done_r) init_next_state = INIT_DUMMY_ACTIVE; else init_next_state = INIT_IDLE; end INIT_CNTR_PRECH_3: init_next_state = INIT_PRECHARGE; INIT_CNTR_DONE: init_next_state = INIT_IDLE; default : init_next_state = INIT_IDLE; endcase end end INIT_CNT_200: init_next_state = INIT_CNT_200_WAIT; INIT_CNT_200_WAIT: if (cnt_200_cycle_done_r) init_next_state = INIT_IDLE; INIT_PRECHARGE: init_next_state = INIT_PRECHARGE_WAIT; INIT_PRECHARGE_WAIT: if (cnt_cmd_ok_r)begin if (init_done_r && (!(&calib_done_r))) init_next_state = INIT_AUTO_REFRESH; else init_next_state = INIT_IDLE; end INIT_ZQCL: init_next_state = INIT_WAIT_DLLK_ZQINIT; INIT_WAIT_DLLK_ZQINIT: if (cnt_200_cycle_done_r) init_next_state = INIT_IDLE; INIT_LOAD_MODE: init_next_state = INIT_MODE_REGISTER_WAIT; INIT_MODE_REGISTER_WAIT: if (cnt_cmd_ok_r) init_next_state = INIT_IDLE; INIT_AUTO_REFRESH: init_next_state = INIT_AUTO_REFRESH_WAIT; INIT_AUTO_REFRESH_WAIT: // MIG 2.4: Modified to issue an Auto Refresh commmand // to each chip select during various calibration stages if (auto_cnt_r < CS_NUM && init_done_r) begin if (cnt_cmd_ok_r) init_next_state = INIT_AUTO_REFRESH; end else if (cnt_cmd_ok_r)begin if(init_done_r) init_next_state = INIT_DUMMY_ACTIVE; else init_next_state = INIT_IDLE; end INIT_DEEP_MEMORY_ST: init_next_state = INIT_IDLE; // single row activate. All subsequent calibration writes and // read will take place in this row INIT_DUMMY_ACTIVE: init_next_state = INIT_DUMMY_ACTIVE_WAIT; INIT_DUMMY_ACTIVE_WAIT: if (cnt_cmd_ok_r)begin if (~calib_done_r[0]) begin // if returning to stg1 after refresh, don't need to write if (cal1_started_r) init_next_state = INIT_CAL1_READ; // if first entering stg1, need to write training pattern else init_next_state = INIT_CAL1_WRITE; end else if (~calib_done[1]) begin if (cal2_started_r) init_next_state = INIT_CAL2_READ; else init_next_state = INIT_CAL2_WRITE; end else if (~calib_done_r[2]) init_next_state = INIT_CAL3_WRITE; else init_next_state = INIT_CAL4_READ; end // Stage 1 calibration (write and continuous read) INIT_CAL1_WRITE: if (burst_addr_r == 2'b10) init_next_state = INIT_CAL1_WRITE_READ; INIT_CAL1_WRITE_READ: if (cnt_cmd_ok_r) init_next_state = INIT_CAL1_READ; INIT_CAL1_READ: // Stage 1 requires inter-stage auto-refresh if (calib_done_r[0] || refresh_req) init_next_state = INIT_CAL1_READ_WAIT; INIT_CAL1_READ_WAIT: if (cnt_cmd_ok_r) init_next_state = INIT_CALIB_REF; // Stage 2 calibration (write and continuous read) INIT_CAL2_WRITE: if (burst_addr_r == 2'b10) init_next_state = INIT_CAL2_WRITE_READ; INIT_CAL2_WRITE_READ: if (cnt_cmd_ok_r) init_next_state = INIT_CAL2_READ; INIT_CAL2_READ: // Stage 2 requires inter-stage auto-refresh if (calib_done_r[1] || refresh_req) init_next_state = INIT_CAL2_READ_WAIT; INIT_CAL2_READ_WAIT: if(cnt_cmd_ok_r) init_next_state = INIT_CALIB_REF; // Stage 3 calibration (write and continuous read) INIT_CAL3_WRITE: if (burst_addr_r == 2'b10) init_next_state = INIT_CAL3_WRITE_READ; INIT_CAL3_WRITE_READ: if (cnt_cmd_ok_r) init_next_state = INIT_CAL3_READ; INIT_CAL3_READ: if (burst_addr_r == 2'b10) init_next_state = INIT_CAL3_READ_WAIT; INIT_CAL3_READ_WAIT: begin if (cnt_rd_ok_r) if (calib_done_r[2]) begin init_next_state = INIT_CALIB_REF; end else init_next_state = INIT_CAL3_READ; end // Stage 4 calibration (continuous read only, same pattern as stage 3) // only used if DQS_GATE supported INIT_CAL4_READ: if (burst_addr_r == 2'b10) init_next_state = INIT_CAL4_READ_WAIT; INIT_CAL4_READ_WAIT: begin if (cnt_rd_ok_r) // Stage 4 requires inter-stage auto-refresh if (calib_done_r[3] || refresh_req) init_next_state = INIT_PRECHARGE; else init_next_state = INIT_CAL4_READ; end INIT_CALIB_REF: init_next_state = INIT_PRECHARGE; endcase end //*************************************************************************** // Memory control/address //*************************************************************************** always @(posedge clkdiv0) if ((init_state_r == INIT_DUMMY_ACTIVE) || (init_state_r == INIT_PRECHARGE) || (init_state_r == INIT_LOAD_MODE) || (init_state_r == INIT_AUTO_REFRESH)) begin ddr_ras_n_r <= 1'b0; end else begin ddr_ras_n_r <= 1'b1; end always @(posedge clkdiv0) if ((init_state_r == INIT_LOAD_MODE) || (init_state_r == INIT_AUTO_REFRESH) || (cal_write_read && (burst_cnt_r == 2'b00))) begin ddr_cas_n_r <= 1'b0; end else begin ddr_cas_n_r <= 1'b1; end always @(posedge clkdiv0) if ((init_state_r == INIT_LOAD_MODE) || (init_state_r == INIT_PRECHARGE) || (init_state_r == INIT_ZQCL) || (cal_write && (burst_cnt_r == 2'b00)))begin ddr_we_n_r <= 1'b0; end else begin ddr_we_n_r <= 1'b1; end //***************************************************************** // memory address during init //***************************************************************** always @(posedge clkdiv0) begin if ((init_state_r == INIT_PRECHARGE) || (init_state_r == INIT_ZQCL))begin // Precharge all - set A10 = 1 ddr_addr_r <= {ROW_WIDTH{1'b0}}; ddr_addr_r[10] <= 1'b1; ddr_ba_r <= {BANK_WIDTH{1'b0}}; end else if (init_state_r == INIT_LOAD_MODE) begin ddr_ba_r <= {BANK_WIDTH{1'b0}}; ddr_addr_r <= {ROW_WIDTH{1'b0}}; case (init_cnt_r) // EMR (2) INIT_CNTR_EMR2_INIT: begin ddr_ba_r[1:0] <= 2'b10; ddr_addr_r <= {ROW_WIDTH{1'b0}}; end // EMR (3) INIT_CNTR_EMR3_INIT: begin ddr_ba_r[1:0] <= 2'b11; if(DDR_TYPE == DDR3) ddr_addr_r <= load_mode_reg3[ROW_WIDTH-1:0]; else ddr_addr_r <= {ROW_WIDTH{1'b0}}; end // EMR write - A0 = 0 for DLL enable INIT_CNTR_EMR_EN_DLL: begin ddr_ba_r[1:0] <= 2'b01; if(DDR_TYPE == DDR3) ddr_addr_r <= load_mode_reg1[ROW_WIDTH-1:0]; else ddr_addr_r <= ext_mode_reg[ROW_WIDTH-1:0]; end // MR write, reset DLL (A8=1) INIT_CNTR_MR_RST_DLL: begin if(DDR_TYPE == DDR3) ddr_addr_r <= load_mode_reg0[ROW_WIDTH-1:0]; else ddr_addr_r <= load_mode_reg[ROW_WIDTH-1:0]; ddr_ba_r[1:0] <= 2'b00; ddr_addr_r[8] <= 1'b1; end // MR write, unreset DLL (A8=0) INIT_CNTR_MR_ACT_DLL: begin ddr_ba_r[1:0] <= 2'b00; ddr_addr_r <= load_mode_reg[ROW_WIDTH-1:0]; end // EMR write, OCD default state INIT_CNTR_EMR_DEF_OCD: begin ddr_ba_r[1:0] <= 2'b01; ddr_addr_r <= ext_mode_reg[ROW_WIDTH-1:0]; ddr_addr_r[9:7] <= 3'b111; end // EMR write - OCD exit INIT_CNTR_EMR_EXIT_OCD: begin ddr_ba_r[1:0] <= 2'b01; ddr_addr_r <= ext_mode_reg[ROW_WIDTH-1:0]; end default: begin ddr_ba_r <= {BANK_WIDTH{1'bx}}; ddr_addr_r <= {ROW_WIDTH{1'bx}}; end endcase end else if (cal_write_read) begin // when writing or reading for Stages 2-4, since training pattern is // either 4 (stage 2) or 8 (stage 3-4) long, if BURST LEN < 8, then // need to issue multiple bursts to read entire training pattern ddr_addr_r[ROW_WIDTH-1:3] <= {ROW_WIDTH-4{1'b0}}; ddr_addr_r[2:0] <= {burst_addr_r, 1'b0}; ddr_ba_r <= {BANK_WIDTH-1{1'b0}}; end else if (init_state_r == INIT_DUMMY_ACTIVE) begin // all calibration writing read takes place in row 0x0 only ddr_ba_r <= {BANK_WIDTH{1'b0}}; ddr_addr_r <= {ROW_WIDTH{1'b0}}; end else begin // otherwise, cry me a river ddr_ba_r <= {BANK_WIDTH{1'bx}}; ddr_addr_r <= {ROW_WIDTH{1'bx}}; end end // Keep CKE asserted after initial power-on delay always @(posedge clkdiv0) ddr_cke_r <= {CKE_WIDTH{done_200us_r}}; // register commands to memory. Two clock cycle delay from state -> output always @(posedge clk0) begin ddr_addr_r1 <= ddr_addr_r; ddr_ba_r1 <= ddr_ba_r; ddr_cas_n_r1 <= ddr_cas_n_r; ddr_ras_n_r1 <= ddr_ras_n_r; ddr_we_n_r1 <= ddr_we_n_r; ddr_cs_n_r1 <= ddr_cs_n_r; end // always @ (posedge clk0) always @(posedge clk0) init_state_r1_2t <= init_state_r1; // logic to toggle chip select. The chip_select is // clocked of clkdiv0 and will be asserted for // two clock cycles. always @(posedge clk0) begin if(rst0) ddr_cs_disable_r <= {CS_NUM{1'b0}}; else begin if(| ddr_cs_disable_r) ddr_cs_disable_r <= {CS_NUM{1'b0}}; else begin if (TWO_T_TIME_EN) begin if (init_state_r1_2t == INIT_PRECHARGE && init_done_r) ddr_cs_disable_r <= 'd3; else ddr_cs_disable_r[chip_cnt_r] <= ~ddr_cs_n_r1[chip_cnt_r]; end else begin if (init_state_r1 == INIT_PRECHARGE && init_done_r) ddr_cs_disable_r <= 'd3; else ddr_cs_disable_r[chip_cnt_r] <= ~ddr_cs_n_r[chip_cnt_r]; end end end end assign phy_init_addr = ddr_addr_r; assign phy_init_ba = ddr_ba_r; assign phy_init_cas_n = ddr_cas_n_r; assign phy_init_cke = ddr_cke_r; assign phy_init_ras_n = ddr_ras_n_r; assign phy_init_we_n = ddr_we_n_r; assign phy_init_cs_n = (TWO_T_TIME_EN) ? ddr_cs_n_r1 | ddr_cs_disable_r : ddr_cs_n_r| ddr_cs_disable_r; endmodule
Go to most recent revision | Compare with Previous | Blame | View Log