URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [ref/] [hs7729pci.html] - Rev 611
Go to most recent revision | Compare with Previous | Blame | View Log
<!-- Copyright (C) 2003 Red Hat, Inc. --> <!-- This material may be distributed only subject to the terms --> <!-- and conditions set forth in the Open Publication License, v1.0 --> <!-- or later (the latest version is presently available at --> <!-- http://www.opencontent.org/openpub/). --> <!-- Distribution of the work or derivative of the work in any --> <!-- standard (paper) book form is prohibited unless prior --> <!-- permission is obtained from the copyright holder. --> <HTML ><HEAD ><TITLE >SuperH/SH3(SH7729) Hitachi HS7729PCI</TITLE ><meta name="MSSmartTagsPreventParsing" content="TRUE"> <META NAME="GENERATOR" CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+ "><LINK REL="HOME" TITLE="eCos Reference Manual" HREF="ecos-ref.html"><LINK REL="UP" TITLE="Installation and Testing" HREF="installation-and-testing.html"><LINK REL="PREVIOUS" TITLE="SuperH/SH3(SH7709) Hitachi Solution Engine 7709" HREF="se7709.html"><LINK REL="NEXT" TITLE="SuperH/SH3(SH77X9) Hitachi Solution Engine 77X9" HREF="se77x9.html"></HEAD ><BODY CLASS="SECT1" BGCOLOR="#FFFFFF" TEXT="#000000" LINK="#0000FF" VLINK="#840084" ALINK="#0000FF" ><DIV CLASS="NAVHEADER" ><TABLE SUMMARY="Header navigation table" WIDTH="100%" BORDER="0" CELLPADDING="0" CELLSPACING="0" ><TR ><TH COLSPAN="3" ALIGN="center" >eCos Reference Manual</TH ></TR ><TR ><TD WIDTH="10%" ALIGN="left" VALIGN="bottom" ><A HREF="se7709.html" ACCESSKEY="P" >Prev</A ></TD ><TD WIDTH="80%" ALIGN="center" VALIGN="bottom" >Chapter 5. Installation and Testing</TD ><TD WIDTH="10%" ALIGN="right" VALIGN="bottom" ><A HREF="se77x9.html" ACCESSKEY="N" >Next</A ></TD ></TR ></TABLE ><HR ALIGN="LEFT" WIDTH="100%"></DIV ><DIV CLASS="SECT1" ><H1 CLASS="SECT1" ><A NAME="HS7729PCI">SuperH/SH3(SH7729) Hitachi HS7729PCI</H1 ><DIV CLASS="SECT2" ><H2 CLASS="SECT2" ><A NAME="AEN7363">Overview</H2 ><P >RedBoot uses the COM1 and COM2 serial ports (and the debug port on the motherboard). The default serial port settings are 38400,8,N,1. Ethernet is also supported using a D-Link DFE-530TX PCI plugin card. Management of onboard flash is also supported. </P ><P >The following RedBoot configurations are supported: <DIV CLASS="INFORMALTABLE" ><A NAME="AEN7373"><P ></P ><TABLE BORDER="1" CLASS="CALSTABLE" ><THEAD ><TR ><TH ALIGN="LEFT" VALIGN="TOP" >Configuration</TH ><TH ALIGN="LEFT" VALIGN="TOP" >Mode</TH ><TH ALIGN="LEFT" VALIGN="TOP" >Description</TH ><TH ALIGN="LEFT" VALIGN="TOP" >File</TH ></TR ></THEAD ><TBODY ><TR ><TD ALIGN="LEFT" VALIGN="TOP" >ROM</TD ><TD ALIGN="LEFT" VALIGN="TOP" >[ROM]</TD ><TD ALIGN="LEFT" VALIGN="TOP" >RedBoot running from the board's flash boot sector.</TD ><TD ALIGN="LEFT" VALIGN="TOP" >redboot_ROM.ecm</TD ></TR ><TR ><TD ALIGN="LEFT" VALIGN="TOP" >RAM</TD ><TD ALIGN="LEFT" VALIGN="TOP" >[RAM]</TD ><TD ALIGN="LEFT" VALIGN="TOP" >RedBoot running from RAM with RedBoot in the flash boot sector.</TD ><TD ALIGN="LEFT" VALIGN="TOP" >redboot_RAM.ecm</TD ></TR ></TBODY ></TABLE ><P ></P ></DIV ></P ></DIV ><DIV CLASS="SECT2" ><H2 CLASS="SECT2" ><A NAME="AEN7392">Initial Installation Method</H2 ><P >A ROM mode RedBoot image must be programmed into the two EPROMs. Two files with a split version of the ROM mode image is provided: it is also possible to recreate these from the <TT CLASS="FILENAME" >redboot.bin</TT > file, but requires the <SPAN CLASS="APPLICATION" >split_word.c</SPAN > program in <TT CLASS="FILENAME" >hal/sh/hs7729pci/<TT CLASS="REPLACEABLE" ><I >VERSION</I ></TT >/misc</TT > to be built and executed with the <TT CLASS="FILENAME" >redboot.bin</TT > filename as sole argument.</P ><P >After doing this it is advised that another ROM mode image of RedBoot is programmed into the on-board flash, and that copy be used for booting the board. This allows for software programmed updates of RedBoot instead of having to reprogram the EPROMs.</P ><P ></P ><OL TYPE="1" ><LI ><P >Program the EPROMs with RedBoot. The .lo image should go in socket M1 and the .hi image in socket M2.</P ></LI ><LI ><P >Set switch SW1-6 to ON [boot from EPROM]</P ></LI ><LI ><P >Follow the instructions under Flash management for updating the flash copy of RedBoot, but force the flash destination address with <TABLE BORDER="5" BGCOLOR="#E0E0F0" WIDTH="70%" ><TR ><TD ><PRE CLASS="SCREEN" ><TT CLASS="USERINPUT" ><B >-f 0x80400000</B ></TT ></PRE ></TD ></TR ></TABLE > due to setting of the SW1-6 switch.</P ></LI ><LI ><P >Set switch SW1-6 to OFF [boot from flash] and reboot the board. You should now see the RedBoot banner. At this time you may want to issue the command <B CLASS="COMMAND" >fis init</B > to initialize the flash table with the correct addresses.</P ></LI ></OL ></DIV ><DIV CLASS="SECT2" ><H2 CLASS="SECT2" ><A NAME="AEN7413">Special RedBoot Commands</H2 ><P >The <B CLASS="COMMAND" >exec</B > command which allows the loading and execution of Linux kernels is supported for this board (see <A HREF="executing-programs.html" >the Section called <I >Executing Programs from RedBoot</I > in Chapter 2</A >). The <B CLASS="COMMAND" >exec</B > parameters used for the HS7729PCI are:</P ><P ></P ><DIV CLASS="VARIABLELIST" ><DL ><DT >-b <TT CLASS="REPLACEABLE" ><I ><addr></I ></TT ></DT ><DD ><P >Parameter block address. This is normally the first page of the kernel image and defaults to 0x8c101000</P ></DD ><DT >-i <TT CLASS="REPLACEABLE" ><I ><addr></I ></TT ></DT ><DD ><P >Start address of initrd image</P ></DD ><DT >-j <TT CLASS="REPLACEABLE" ><I ><size></I ></TT ></DT ><DD ><P >Size of initrd image</P ></DD ><DT >-c <TT CLASS="REPLACEABLE" ><I >"args"</I ></TT ></DT ><DD ><P >Kernel arguments string</P ></DD ><DT >-m <TT CLASS="REPLACEABLE" ><I ><flags></I ></TT ></DT ><DD ><P >Mount rdonly flags. If set to a non-zero value the root partition will be mounted read-only.</P ></DD ><DT >-f <TT CLASS="REPLACEABLE" ><I ><flags></I ></TT ></DT ><DD ><P >RAM disk flags. Should normally be 0x4000</P ></DD ><DT >-r <TT CLASS="REPLACEABLE" ><I ><device number></I ></TT ></DT ><DD ><P >Root device specification. /dev/ram is 0x0101</P ></DD ><DT >-l <TT CLASS="REPLACEABLE" ><I ><type></I ></TT ></DT ><DD ><P >Loader type</P ></DD ></DL ></DIV ><P >Finally the kernel entry address can be specified as an optional argument. The default is 0x8c102000</P ><P >On the HS7729PCI, Linux expects to be loaded at address 0x8c101000 with the entry point at 0x8c102000. This is configurable in the kernel using the CONFIG_MEMORY_START option.</P ></DIV ><DIV CLASS="SECT2" ><H2 CLASS="SECT2" ><A NAME="AEN7462">Memory Maps</H2 ><P >RedBoot sets up the following memory map on the HS7729PCI board.<TABLE BORDER="5" BGCOLOR="#E0E0F0" WIDTH="70%" ><TR ><TD ><PRE CLASS="PROGRAMLISTING" >Physical Address Range Description ----------------------- ----------- 0x80000000 - 0x803fffff Flash (MBM29LV160) 0x80400000 - 0x807fffff EPROM (M27C800) 0x82000000 - 0x82ffffff SRAM 0x89000000 - 0x89ffffff SRAM 0x8c000000 - 0x8fffffff SDRAM 0xa8000000 - 0xa800ffff SuperIO (FDC37C935A) 0xa8400000 - 0xa87fffff USB function (ML60851C) 0xa8800000 - 0xa8bfffff USB host (SL11HT) 0xa8c00000 - 0xa8c3ffff Switches 0xa8c40000 - 0xa8c7ffff LEDs 0xa8c80000 - 0xa8cfffff Interrupt controller 0xb0000000 - 0xb3ffffff PCI (SD0001) 0xb8000000 - 0xbbffffff PCMCIA (MaruBun)</PRE ></TD ></TR ></TABLE ></P ></DIV ><DIV CLASS="SECT2" ><H2 CLASS="SECT2" ><A NAME="AEN7466">Rebuilding RedBoot</H2 ><P >These shell variables provide the platform-specific information needed for building RedBoot according to the procedure described in <A HREF="rebuilding-redboot.html" >Chapter 3</A >: <TABLE BORDER="5" BGCOLOR="#E0E0F0" WIDTH="70%" ><TR ><TD ><PRE CLASS="PROGRAMLISTING" >export TARGET=hs7729pci export ARCH_DIR=sh export PLATFORM_DIR=hs7729pci</PRE ></TD ></TR ></TABLE ></P ><P >The names of configuration files are listed above with the description of the associated modes.</P ></DIV ></DIV ><DIV CLASS="NAVFOOTER" ><HR ALIGN="LEFT" WIDTH="100%"><TABLE SUMMARY="Footer navigation table" WIDTH="100%" BORDER="0" CELLPADDING="0" CELLSPACING="0" ><TR ><TD WIDTH="33%" ALIGN="left" VALIGN="top" ><A HREF="se7709.html" ACCESSKEY="P" >Prev</A ></TD ><TD WIDTH="34%" ALIGN="center" VALIGN="top" ><A HREF="ecos-ref.html" ACCESSKEY="H" >Home</A ></TD ><TD WIDTH="33%" ALIGN="right" VALIGN="top" ><A HREF="se77x9.html" ACCESSKEY="N" >Next</A ></TD ></TR ><TR ><TD WIDTH="33%" ALIGN="left" VALIGN="top" >SuperH/SH3(SH7709) Hitachi Solution Engine 7709</TD ><TD WIDTH="34%" ALIGN="center" VALIGN="top" ><A HREF="installation-and-testing.html" ACCESSKEY="U" >Up</A ></TD ><TD WIDTH="33%" ALIGN="right" VALIGN="top" >SuperH/SH3(SH77X9) Hitachi Solution Engine 77X9</TD ></TR ></TABLE ></DIV ></BODY ></HTML >
Go to most recent revision | Compare with Previous | Blame | View Log