URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [connecting-target-sim.html] - Rev 811
Go to most recent revision | Compare with Previous | Blame | View Log
<!-- Copyright (C) 2003 Red Hat, Inc. --> <!-- This material may be distributed only subject to the terms --> <!-- and conditions set forth in the Open Publication License, v1.0 --> <!-- or later (the latest version is presently available at --> <!-- http://www.opencontent.org/openpub/). --> <!-- Distribution of the work or derivative of the work in any --> <!-- standard (paper) book form is prohibited unless prior --> <!-- permission is obtained from the copyright holder. --> <HTML ><HEAD ><TITLE >Using A Simulator Target</TITLE ><meta name="MSSmartTagsPreventParsing" content="TRUE"> <META NAME="GENERATOR" CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+ "><LINK REL="HOME" TITLE="eCos User Guide" HREF="ecos-user-guide.html"><LINK REL="UP" TITLE="Target Setup" HREF="user-guide-installation-target.html"><LINK REL="PREVIOUS" TITLE="Connecting Via Ethernet" HREF="connecting-target-ethernet.html"><LINK REL="NEXT" TITLE="Using A Synthetic Target" HREF="connecting-target-synth.html"></HEAD ><BODY CLASS="SECT1" BGCOLOR="#FFFFFF" TEXT="#000000" LINK="#0000FF" VLINK="#840084" ALINK="#0000FF" ><DIV CLASS="NAVHEADER" ><TABLE SUMMARY="Header navigation table" WIDTH="100%" BORDER="0" CELLPADDING="0" CELLSPACING="0" ><TR ><TH COLSPAN="3" ALIGN="center" >eCos User Guide</TH ></TR ><TR ><TD WIDTH="10%" ALIGN="left" VALIGN="bottom" ><A HREF="connecting-target-ethernet.html" ACCESSKEY="P" >Prev</A ></TD ><TD WIDTH="80%" ALIGN="center" VALIGN="bottom" >Chapter 9. Target Setup</TD ><TD WIDTH="10%" ALIGN="right" VALIGN="bottom" ><A HREF="connecting-target-synth.html" ACCESSKEY="N" >Next</A ></TD ></TR ></TABLE ><HR ALIGN="LEFT" WIDTH="100%"></DIV ><DIV CLASS="SECT1" ><H1 CLASS="SECT1" ><A NAME="CONNECTING-TARGET-SIM">Using A Simulator Target</H1 ><P >GDB connects to all simulator targets using the same basic command, although each simulator may require additional options. These are listed in the document describing the target, and should be used when connecting.</P ><P >Connect to the target by issuing the following command in GDB console mode:</P ><TABLE BORDER="5" BGCOLOR="#E0E0F0" WIDTH="70%" ><TR ><TD ><PRE CLASS="PROGRAMLISTING" >(gdb) target sim [target specific options]</PRE ></TD ></TR ></TABLE ><P >In Insight, connect by opening the <SPAN CLASS="emphasis" ><I CLASS="EMPHASIS" >File->Target Settings</I ></SPAN > window and enter:</P ><TABLE BORDER="5" BGCOLOR="#E0E0F0" WIDTH="70%" ><TR ><TD ><PRE CLASS="PROGRAMLISTING" >Target: Simulator Options: [target specific options]</PRE ></TD ></TR ></TABLE ><P >Set other options according to preference, close the window and select <SPAN CLASS="emphasis" ><I CLASS="EMPHASIS" >Run->Connect to target</I ></SPAN >.</P ></DIV ><DIV CLASS="NAVFOOTER" ><HR ALIGN="LEFT" WIDTH="100%"><TABLE SUMMARY="Footer navigation table" WIDTH="100%" BORDER="0" CELLPADDING="0" CELLSPACING="0" ><TR ><TD WIDTH="33%" ALIGN="left" VALIGN="top" ><A HREF="connecting-target-ethernet.html" ACCESSKEY="P" >Prev</A ></TD ><TD WIDTH="34%" ALIGN="center" VALIGN="top" ><A HREF="ecos-user-guide.html" ACCESSKEY="H" >Home</A ></TD ><TD WIDTH="33%" ALIGN="right" VALIGN="top" ><A HREF="connecting-target-synth.html" ACCESSKEY="N" >Next</A ></TD ></TR ><TR ><TD WIDTH="33%" ALIGN="left" VALIGN="top" >Connecting Via Ethernet</TD ><TD WIDTH="34%" ALIGN="center" VALIGN="top" ><A HREF="user-guide-installation-target.html" ACCESSKEY="U" >Up</A ></TD ><TD WIDTH="33%" ALIGN="right" VALIGN="top" >Using A Synthetic Target</TD ></TR ></TABLE ></DIV ></BODY ></HTML >
Go to most recent revision | Compare with Previous | Blame | View Log