URL https://opencores.org/ocsvn/openrisc_me/openrisc_me/trunk
Subversion Repositories openrisc_me

[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [setup-arm-ep7212.html] - Rev 446

Go to most recent revision | Compare with Previous | Blame | View Log
<!-- Copyright (C) 2003 Red Hat, Inc.                                -->
<!-- This material may be distributed only subject to the terms      -->
<!-- and conditions set forth in the Open Publication License, v1.0  -->
<!-- or later (the latest version is presently available at          -->
<!-- http://www.opencontent.org/openpub/).                           -->
<!-- Distribution of the work or derivative of the work in any       -->
<!-- standard (paper) book form is prohibited unless prior           -->
<!-- permission is obtained from the copyright holder.               -->
<HTML
><HEAD
><TITLE
>Cirrus Logic ARM EP7212 Development Board
Hardware Setup</TITLE
><meta name="MSSmartTagsPreventParsing" content="TRUE">
<META
NAME="GENERATOR"
CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
"><LINK
REL="HOME"
TITLE="eCos User Guide"
HREF="ecos-user-guide.html"><LINK
REL="UP"
TITLE="Target Setup"
HREF="appendix-target-setup.html"><LINK
REL="PREVIOUS"
TITLE="Cirrus Logic ARM EP7211 Development
Board Hardware Setup"
HREF="setup-arm-ep7211.html"><LINK
REL="NEXT"
TITLE="Cirrus Logic ARM EP7312 Development Board
Hardware Setup"
HREF="setup-arm-ep7312.html"></HEAD
><BODY
CLASS="SECT1"
BGCOLOR="#FFFFFF"
TEXT="#000000"
LINK="#0000FF"
VLINK="#840084"
ALINK="#0000FF"
><DIV
CLASS="NAVHEADER"
><TABLE
SUMMARY="Header navigation table"
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TH
COLSPAN="3"
ALIGN="center"
>eCos User Guide</TH
></TR
><TR
><TD
WIDTH="10%"
ALIGN="left"
VALIGN="bottom"
><A
HREF="setup-arm-ep7211.html"
ACCESSKEY="P"
>Prev</A
></TD
><TD
WIDTH="80%"
ALIGN="center"
VALIGN="bottom"
>Appendix A. Target Setup</TD
><TD
WIDTH="10%"
ALIGN="right"
VALIGN="bottom"
><A
HREF="setup-arm-ep7312.html"
ACCESSKEY="N"
>Next</A
></TD
></TR
></TABLE
><HR
ALIGN="LEFT"
WIDTH="100%"></DIV
><DIV
CLASS="SECT1"
><H1
CLASS="SECT1"
><A
NAME="SETUP-ARM-EP7212">Cirrus Logic ARM EP7212 Development Board
Hardware Setup</H1
><P
>The Cirrus Logic EP7212 Development Board is almost identical
to the EP7211 Development Board from a hardware setup viewpoint,
and is based on the same port of eCos. Therefore the earlier documentation
for the EP7211 Development Board can be considered equivalent, but
with the following changes:</P
><P
></P
><UL
><LI
><P
>The first serial port is silk screened as "UART 1" on
the EP7211 Development Board, but is silk screened as "Serial Port
0" on the EP7212 Development Board. Similarly "UART 2" is silk screened
as "Serial Port 1" on the EP7212 Development Board.</P
></LI
><LI
><P
>JP2 (used to control reprogramming of the FLASH) is not
silkscreened with "Boot Enable".</P
></LI
><LI
><P
>To setup the EP7212 Development Board for use with the
ARM Multi-ICE JTAG debugging interface unit, it is necessary to
connect TEST0 and TEST1 of the EP7212 to ground.  On the Development
Board, this is accomplished by placing shorting blocks on JP47 and
JP48. When the shorting blocks are fitted, the board can only be
operated through the Multi-ICE - debugging over a serial line is
not possible.</P
></LI
><LI
><P
>Pre-built GDB stubs are
	      provided in the directory
	      <TT
CLASS="FILENAME"
>loaders/arm-edb7212</TT
> relative to the
	      root of your eCos installation</P
></LI
><LI
><P
>When rebuilding the GDB stub ROM image, change the "Cirrus
Logic processor variant" option (CYGHWR_HAL_ARM_EDB7XXX_VARIANT)
from the EP7211 to the EP7212. This can be selected in the 
<SPAN
CLASS="emphasis"
><I
CLASS="EMPHASIS"
>eCos Configuration Tool</I
></SPAN
>
, or if using ecosconfig, can be set by uncommenting the user_value
property of this option in ecos.ecc and setting it to "EP7212".</P
></LI
></UL
></DIV
><DIV
CLASS="NAVFOOTER"
><HR
ALIGN="LEFT"
WIDTH="100%"><TABLE
SUMMARY="Footer navigation table"
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
><A
HREF="setup-arm-ep7211.html"
ACCESSKEY="P"
>Prev</A
></TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
><A
HREF="ecos-user-guide.html"
ACCESSKEY="H"
>Home</A
></TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
><A
HREF="setup-arm-ep7312.html"
ACCESSKEY="N"
>Next</A
></TD
></TR
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
>Cirrus Logic ARM EP7211 Development
Board Hardware Setup</TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
><A
HREF="appendix-target-setup.html"
ACCESSKEY="U"
>Up</A
></TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
>Cirrus Logic ARM EP7312 Development Board
Hardware Setup</TD
></TR
></TABLE
></DIV
></BODY
></HTML
>
Go to most recent revision | Compare with Previous | Blame | View Log
Browse

Tools

Subversion Repositories openrisc_me

[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [setup-arm-ep7212.html] - Rev 446
