OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [setup-sparclite-sleb.html] - Rev 174

Compare with Previous | Blame | View Log

<!-- Copyright (C) 2003 Red Hat, Inc.                                -->
<!-- This material may be distributed only subject to the terms      -->
<!-- and conditions set forth in the Open Publication License, v1.0  -->
<!-- or later (the latest version is presently available at          -->
<!-- http://www.opencontent.org/openpub/).                           -->
<!-- Distribution of the work or derivative of the work in any       -->
<!-- standard (paper) book form is prohibited unless prior           -->
<!-- permission is obtained from the copyright holder.               -->
<HTML
><HEAD
><TITLE
>SPARClite Hardware Setup</TITLE
><meta name="MSSmartTagsPreventParsing" content="TRUE">
<META
NAME="GENERATOR"
CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
"><LINK
REL="HOME"
TITLE="eCos User Guide"
HREF="ecos-user-guide.html"><LINK
REL="UP"
TITLE="Target Setup"
HREF="appendix-target-setup.html"><LINK
REL="PREVIOUS"
TITLE="PowerPC Architectural Simulator Setup"
HREF="setup-ppc-sim.html"><LINK
REL="NEXT"
TITLE="SPARClite Architectural Simulator Setup"
HREF="setup-sparclite-sim.html"></HEAD
><BODY
CLASS="SECT1"
BGCOLOR="#FFFFFF"
TEXT="#000000"
LINK="#0000FF"
VLINK="#840084"
ALINK="#0000FF"
><DIV
CLASS="NAVHEADER"
><TABLE
SUMMARY="Header navigation table"
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TH
COLSPAN="3"
ALIGN="center"
>eCos User Guide</TH
></TR
><TR
><TD
WIDTH="10%"
ALIGN="left"
VALIGN="bottom"
><A
HREF="setup-ppc-sim.html"
ACCESSKEY="P"
>Prev</A
></TD
><TD
WIDTH="80%"
ALIGN="center"
VALIGN="bottom"
>Appendix A. Target Setup</TD
><TD
WIDTH="10%"
ALIGN="right"
VALIGN="bottom"
><A
HREF="setup-sparclite-sim.html"
ACCESSKEY="N"
>Next</A
></TD
></TR
></TABLE
><HR
ALIGN="LEFT"
WIDTH="100%"></DIV
><DIV
CLASS="SECT1"
><H1
CLASS="SECT1"
><A
NAME="SETUP-SPARCLITE-SLEB">SPARClite Hardware Setup</H1
><P
>The eCos Developer&#8217;s Kit package comes with a ROM
which provides GDB support for the Fujitsu SPARClite Evaluation
Board by way of CygMon<SPAN
CLASS="PRODUCTNAME"
>. </SPAN
></P
><P
>An image of this ROM is also provided at
	  <TT
CLASS="FILENAME"
>BASE_DIR/loaders/sparclite-sleb/cygmon.bin.</TT
> The
ROM is installed in socket IC9 on the evaluation board. Attention
should be paid to the correct orientation of the ROM during installation.</P
><P
>The GDB stub allows communication with GDB using a TCP channel
via the ethernet port at connector J5.</P
><DIV
CLASS="SECT2"
><H2
CLASS="SECT2"
><A
NAME="AEN3509">Ethernet Setup</H2
><P
>The ethernet setup is described in the board&#8217;s manual,
but here is a recapitulation.</P
><P
>Set the board&#8217;s ethernet address using SW1 on the
motherboard:</P
><TABLE
BORDER="5"
BGCOLOR="#E0E0F0"
WIDTH="70%"
><TR
><TD
><PRE
CLASS="PROGRAMLISTING"
>	    SW1-4 SW1-3 SW1-2 SW1-1    Ethernet Address
	    ----- ----- ----- -----    ----------------
	    OFF   OFF   OFF   OFF     No ethernet, use serial
	    OFF   OFF   OFF    ON     00:00:0E:31:00:01
	    OFF   OFF    ON   OFF     00:00:0E:31:00:02
	    OFF   OFF    ON    ON     00:00:0E:31:00:03
	    OFF    ON   OFF   OFF     00:00:0E:31:00:04
	    OFF    ON   OFF    ON     00:00:0E:31:00:05
	    OFF    ON    ON   OFF     00:00:0E:31:00:06
	    OFF    ON    ON    ON     00:00:0E:31:00:07
	    ON    OFF   OFF   OFF     00:00:0E:31:00:08
	    ON    OFF   OFF    ON     00:00:0E:31:00:09
	    ON    OFF    ON   OFF     00:00:0E:31:00:0A
	    ON    OFF    ON    ON     00:00:0E:31:00:0B
	    ON     ON   OFF   OFF     00:00:0E:31:00:0C
	    ON     ON   OFF    ON     00:00:0E:31:00:0D
	    ON     ON    ON   OFF     00:00:0E:31:00:0E
	    ON     ON    ON    ON     00:00:0E:31:00:0F</PRE
></TD
></TR
></TABLE
><DIV
CLASS="SECT3"
><H3
CLASS="SECT3"
><A
NAME="AEN3514">BOOTP/DHCP service on Linux</H3
><P
>Configure the BOOTP or DHCP server on the network to recognize
the evaluation board&#8217;s ethernet address so it can assign
the board an IP address. Below is a sample DHCP server configuration
from a Linux system (<TT
CLASS="FILENAME"
>/etc/dhcpd.conf</TT
>).
It shows a setup for three evaluation boards.</P
><TABLE
BORDER="5"
BGCOLOR="#E0E0F0"
WIDTH="70%"
><TR
><TD
><PRE
CLASS="PROGRAMLISTING"
>#
# DHCP server configuration.
#
allow bootp;
 
subnet 192.168.1.0 netmask 255.255.255.0 {
  host mb831evb {
    hardware ethernet 00:00:0e:31:00:01;
    fixed-address mb831evb;
  }
  host mb832evb {
    hardware ethernet 00:00:0e:31:00:02;
    fixed-address mb832evb;
  }
  host mb833evb {
    hardware ethernet 00:00:0e:31:00:03;
    fixed-address mb833evb;
  }
} </PRE
></TD
></TR
></TABLE
></DIV
><DIV
CLASS="SECT3"
><H3
CLASS="SECT3"
><A
NAME="AEN3519">BOOTP/DHCP boot process</H3
><P
>Even when configured to use a TCP channel, CygMon will still
print a boot message to the serial channel. If the BOOTP process
was successful and an IP address was found, a message &#8220;BOOTP
found xxx.xxx.xxx.xxx&#8221; will be printed where xxx.xxx.xxx.xxx
is the IP address assigned by the BOOTP or DHCP server. If the BOOTP
process fails, a message indicating failure will be printed and
the serial port will be used as the debug channel.</P
><P
>Once the board finds an IP address it will respond to ICMP
echo request packets (ping). This gives a simple means to test the
health of the board.</P
><P
>As described in &#8220;Ethernet Setup&#8221; on&nbsp;page&nbsp;72,
it should now be possible to connect to the SPARClite board from
within GDB by using the command:</P
><TABLE
BORDER="5"
BGCOLOR="#E0E0F0"
WIDTH="70%"
><TR
><TD
><PRE
CLASS="PROGRAMLISTING"
>(gdb) target remote &lt;host&#62;:1000</PRE
></TD
></TR
></TABLE
></DIV
></DIV
><DIV
CLASS="SECT2"
><H2
CLASS="SECT2"
><A
NAME="AEN3525">Serial Setup</H2
><P
>The CygMon stubs also allow communication with GDB by way
of the serial port at connector CON1. The communication parameters
are fixed at 19200 baud, 8 data bits, no parity bit and 1 stop bit
(8-N-1). No flow control is employed. Connection to the host computer
should be made using a null modem cable. A gender changer may also
be required.</P
></DIV
></DIV
><DIV
CLASS="NAVFOOTER"
><HR
ALIGN="LEFT"
WIDTH="100%"><TABLE
SUMMARY="Footer navigation table"
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
><A
HREF="setup-ppc-sim.html"
ACCESSKEY="P"
>Prev</A
></TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
><A
HREF="ecos-user-guide.html"
ACCESSKEY="H"
>Home</A
></TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
><A
HREF="setup-sparclite-sim.html"
ACCESSKEY="N"
>Next</A
></TD
></TR
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
>PowerPC Architectural Simulator Setup</TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
><A
HREF="appendix-target-setup.html"
ACCESSKEY="U"
>Up</A
></TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
>SPARClite Architectural Simulator Setup</TD
></TR
></TABLE
></DIV
></BODY
></HTML
>

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.