URL
https://opencores.org/ocsvn/openrisc_2011-10-31/openrisc_2011-10-31/trunk
Subversion Repositories openrisc_2011-10-31
[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [packages/] [cygmon/] [v2_0/] [misc/] [Notes_CygMon_PID] - Rev 277
Go to most recent revision | Compare with Previous | Blame | View Log
===========================================================================
#####ECOSGPLCOPYRIGHTBEGIN####
## -------------------------------------------
## This file is part of eCos, the Embedded Configurable Operating System.
## Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
##
## eCos is free software; you can redistribute it and/or modify it under
## the terms of the GNU General Public License as published by the Free
## Software Foundation; either version 2 or (at your option) any later version.
##
## eCos is distributed in the hope that it will be useful, but WITHOUT ANY
## WARRANTY; without even the implied warranty of MERCHANTABILITY or
## FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
## for more details.
##
## You should have received a copy of the GNU General Public License along
## with eCos; if not, write to the Free Software Foundation, Inc.,
## 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
##
## As a special exception, if other files instantiate templates or use macros
## or inline functions from this file, or you compile this file and link it
## with other works to produce a work based on this file, this file does not
## by itself cause the resulting work to be covered by the GNU General Public
## License. However the source code for this file must still be made available
## in accordance with section (3) of the GNU General Public License.
##
## This exception does not invalidate any other reasons why a work based on
## this file might be covered by the GNU General Public License.
##
## Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
## at http://sources.redhat.com/ecos/ecos-license/
## -------------------------------------------
#####ECOSGPLCOPYRIGHTEND####
===========================================================================
28 Jan 2000
How to build and install CygMon on the PID
Make CygMon image
~~~~~~~~~~~~~~~~~
Configure and build using the 'cygmon' template for the PID
target. These are the necessary CLI instructions. It can also be done
from the Configtool by selecting the appropriate templates.
% cd /tmp
% mkdir cygmon
% cd cygmon
% ecosconfig new pid cygmon
% ecosconfig tree
% make
This will install some files in ./install/bin:
cygmon.elf: The built CygMon image
cygmon.bin: The image converted to binary (suitable for burning to ROM)
cygmon.img: The relocated ELF image (suitable for FLASH writing, see below)
cygmon.srec: The image converted to srecords
Make FLASH tool
~~~~~~~~~~~~~~~
Again, these are the necessary CLI instructions. It can also be done
from the Configtool by selecting the appropriate templates, and
enabling the option.
% cd /tmp
% mkdir pid-flash
% cd pid-flash
% ecosconfig new pid
% <edit ecos.ecc, enabling the CYGBLD_BUILD_FLASH_TOOL option:>
--- ecos.ecc.orig Fri Jan 28 11:21:43 2000
+++ ecos.ecc Fri Jan 28 11:22:01 2000
@@ -150,7 +150,7 @@
cdl_option CYGBLD_BUILD_FLASH_TOOL {
# Flavor: bool
# No user value, uncomment the following line to provide one.
- # user_value 0
+ user_value 1
# value_source default
# Default value: 0
# Requires: CYG_HAL_STARTUP == "RAM"
% ecosconfig resolve
% ecosconfig tree
% make
The flash tool is installed in ./install/bin
Prepare board for CygMon
~~~~~~~~~~~~~~~~~~~~~~~~
1. Set jumper 7-8 on LK6 [using the Angle code in the 16 bit EPROM]
2. Set jumper 5-6 on LK6 [select 8bit ROM mode]
3. Set jumper LK18 [ROM remap - this is also required for eCos]
4. Set S1 to 0-0-1-1 [20MHz operation]
Program FLASH
~~~~~~~~~~~~~
1. Download the CygMon relocated image onto the PID board:
% cd /tmp
% arm-elf-gdb -nw cygmon/install/bin/cygmon.img
(gdb) target rdi s=<serial device>
Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID
Built with Serial(x1), Parallel, DCC
Rebuilt on Apr 7 1998 at 22:20:43
Serial Rate: 9600
Connected to ARM RDI target.
(gdb) load
Loading section .rom_vectors, size 0x60 lma 0x60000
Loading section .text, size 0xeea8 lma 0x60060
Loading section .rodata, size 0x304c lma 0x6ef08
Loading section .data, size 0x7f8 lma 0x71f54
Start address 0x60060 , load size 75596
Transfer rate: 5548 bits/sec.
(gdb) quit
This will download the stubs onto the board at 0x60000..0x80000
Use /dev/ttyS0, COM1 or similar for the <serial device> name.
2. Now download the FLASH programmer tool
% arm-elf-gdb -nw pid-flash/install/bin/prog_flash.img
(gdb) target rdi s=<serial device>
Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID
Built with Serial(x1), Parallel, DCC
Rebuilt on Apr 7 1998 at 22:20:43
Serial Rate: 9600
Connected to ARM RDI target.
(gdb) load
Loading section .rom_vectors, size 0x60 lma 0x4000
Loading section .text, size 0x4964 lma 0x4060
Loading section .rodata, size 0x384 lma 0x89c4
Loading section .data, size 0x28c lma 0x8d48
Start address 0x4060 , load size 20436
Transfer rate: 5449 bits/sec.
(gdb) cont
3. The FLASH tool will output some text on the board serial port B at
38400 baud:
ARM eCos
FLASH here!
manuf: 8, device: 40
Error: Wrong Manufaturer: 08
... Please change FLASH jumper
4. This text is repeated until you remove the jumper 7-8 on LK6. Then
the output should be:
manuf: 1F, device: A4
AT29C040A recognised
About to program FLASH using data at 60000..80000
*** Press RESET now to abort!
5. You have about 10 seconds to abort the operation by pressing
reset. After this timeout, the FLASH programming happens:
...Programming FLASH
All done!
6. Quit/kill the GDB process which will hang.
7. Next time you reset the board, CygMon will be in control, communicating
on serial port A at 38400 baud. See documentation for further details
on how to connect with GDB.
Go to most recent revision | Compare with Previous | Blame | View Log