Subversion Repositories openrisc

//==========================================================================
//
//        can_busload.c
//
//        CAN bus load test
//
//==========================================================================
// ####ECOSGPLCOPYRIGHTBEGIN####                                            
// -------------------------------------------                              
// This file is part of eCos, the Embedded Configurable Operating System.   
// Copyright (C) 1998, 1999, 2000, 2001, 2002 Free Software Foundation, Inc.
//
// eCos is free software; you can redistribute it and/or modify it under    
// the terms of the GNU General Public License as published by the Free     
// Software Foundation; either version 2 or (at your option) any later      
// version.                                                                 
//
// eCos is distributed in the hope that it will be useful, but WITHOUT      
// ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or    
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License    
// for more details.                                                        
//
// You should have received a copy of the GNU General Public License        
// along with eCos; if not, write to the Free Software Foundation, Inc.,    
// 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.            
//
// As a special exception, if other files instantiate templates or use      
// macros or inline functions from this file, or you compile this file      
// and link it with other works to produce a work based on this file,       
// this file does not by itself cause the resulting work to be covered by   
// the GNU General Public License. However the source code for this file    
// must still be made available in accordance with section (3) of the GNU   
// General Public License v2.                                               
//
// This exception does not invalidate any other reasons why a work based    
// on this file might be covered by the GNU General Public License.         
// -------------------------------------------                              
// ####ECOSGPLCOPYRIGHTEND####                                              
//==========================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):     Uwe Kindler
// Contributors:  Uwe Kindler
// Date:          2007-06-26
// Description:   CAN bus load test
//####DESCRIPTIONEND####
 
 
//===========================================================================
//                                INCLUDES
//===========================================================================
#include <pkgconf/system.h>
 
#include <cyg/infra/testcase.h>         // test macros
#include <cyg/infra/cyg_ass.h>          // assertion macros
#include <cyg/infra/diag.h>
 
// Package requirements
#if defined(CYGPKG_IO_CAN) && defined(CYGPKG_KERNEL)
 
#include <pkgconf/kernel.h>
#include <cyg/io/io.h>
#include <cyg/io/canio.h>
 
 
// Package option requirements
#if defined(CYGFUN_KERNEL_API_C)
 
#include <cyg/hal/hal_arch.h>           // CYGNUM_HAL_STACK_SIZE_TYPICAL
#include <cyg/kernel/kapi.h>
 
// We need two CAN channels
#if defined(CYGPKG_DEVS_CAN_LPC2XXX_CAN0) && defined(CYGPKG_DEVS_CAN_LPC2XXX_CAN1)
 
 
// The same baud rates are required because we send from one channel to the other one
#if CYGNUM_DEVS_CAN_LPC2XXX_CAN0_KBAUD == CYGNUM_DEVS_CAN_LPC2XXX_CAN1_KBAUD
 
 
// We need a large RX buffer
#ifdef CYGNUM_DEVS_CAN_LPC2XXX_CAN0_QUEUESIZE_RX_1024
 
#include "can_test_aux.inl" // include CAN test auxiliary functions
//===========================================================================
//                               DATA TYPES
//===========================================================================
typedef struct st_thread_data
{
    cyg_thread   obj;
    long         stack[CYGNUM_HAL_STACK_SIZE_TYPICAL];
    cyg_handle_t hdl;
} thread_data_t;
 
 
//===========================================================================
//                              LOCAL DATA
//===========================================================================
cyg_thread_entry_t can0_thread;
thread_data_t      can0_thread_data;
cyg_io_handle_t    hCAN_Tbl[2];
 
 
//===========================================================================
// Thread 0
//===========================================================================
void can0_thread(cyg_addrword_t data)
{
    cyg_uint32      len;
    cyg_can_message tx_msg;
    cyg_can_event   rx_event;
    cyg_uint32      i;
    cyg_uint32      rx_msg_cnt = 0;
 
 
    //
    // Prepeare message - we use a data length of 0 bytes here. Each received message
    // causes an iterrupt. The shortest message is a 0 data byte message. This will generate
    // the highest interrupt rate
    //
    CYG_CAN_MSG_SET_PARAM(tx_msg, 0, CYGNUM_CAN_ID_STD, 0, CYGNUM_CAN_FRAME_DATA);
 
    //
    // Now send 1024 CAN messages as fast as possible to stress the receiver of CAN
    // channel 1
    //
    for (i = 0; i< 1024; ++i)
    {
        tx_msg.id = i; 
        len = sizeof(tx_msg);
        if (ENOERR != cyg_io_write(hCAN_Tbl[1], &tx_msg, &len))
        {
            CYG_TEST_FAIL_FINISH("Error writing to channel 0");    
        }
    }
 
    //
    // Now try to receive all 1024 CAN messages. If all messages are received
    // and no overrun occured then the message processing is fast enought
    //
    while (1)
    {
        len = sizeof(rx_event);  
        //
        // First receive CAN event from real CAN hardware
        //
        len = sizeof(rx_event);
        if (ENOERR != cyg_io_read(hCAN_Tbl[0], &rx_event, &len))
        {
            CYG_TEST_FAIL_FINISH("Error reading from channel 1");   
        }
 
        if (rx_event.flags & CYGNUM_CAN_EVENT_RX)
        {
            print_can_msg(&rx_event.msg, "RX chan 1:");
            rx_msg_cnt++;
            if (rx_msg_cnt == 1024)
            {
                CYG_TEST_PASS_FINISH("CAN load test OK");        
            }
        } // if (rx_event.flags & CYGNUM_CAN_EVENT_RX)
        else
        {
            print_can_flags(rx_event.flags, "");  
            if (rx_event.flags & CYGNUM_CAN_EVENT_OVERRUN_RX)
            {
                CYG_TEST_FAIL_FINISH("RX overrun for channel 1");       
            }
 
            if (rx_event.flags & CYGNUM_CAN_EVENT_ERR_PASSIVE)
            {
                CYG_TEST_FAIL_FINISH("Channel 1 error passive event");       
            }
 
            if (rx_event.flags & CYGNUM_CAN_EVENT_BUS_OFF)
            {
                CYG_TEST_FAIL_FINISH("Channel 1 bus off event");       
            }
        }
    } // while (1)
}
 
 
//===========================================================================
// Entry point
//===========================================================================
void cyg_start(void)
{
    CYG_TEST_INIT();
 
    //
    // open CAN device driver channel 1
    //
    if (ENOERR != cyg_io_lookup(CYGPKG_DEVS_CAN_LPC2XXX_CAN0_NAME, &hCAN_Tbl[0])) 
    {
        CYG_TEST_FAIL_FINISH("Error opening CAN channel 0");
    }
 
 
    //
    // open CAN device driver channel 2
    //
    if (ENOERR != cyg_io_lookup(CYGPKG_DEVS_CAN_LPC2XXX_CAN1_NAME, &hCAN_Tbl[1])) 
    {
        CYG_TEST_FAIL_FINISH("Error opening CAN channel 1");
    }
 
    //
    // create the main thread
    //
    cyg_thread_create(5, can0_thread, 
                        (cyg_addrword_t) 0,
                        "can_tx_thread", 
                        (void *) can0_thread_data.stack, 
                        1024 * sizeof(long),
                        &can0_thread_data.hdl, 
                        &can0_thread_data.obj);
 
    cyg_thread_resume(can0_thread_data.hdl);
 
    cyg_scheduler_start();
}
#else // CYGNUM_DEVS_CAN_LPC2XXX_CAN0_QUEUESIZE_RX_1024
#define N_A_MSG "Channel 0 needs RX buffer size for 1024 events"
#endif
 
#else // CYGNUM_DEVS_CAN_LPC2XXX_CAN0_KBAUD == CYGNUM_DEVS_CAN_LPC2XXX_CAN1_KBAUD
#define N_A_MSG "Baudrate of channel 0 and 1 need to be equal"
#endif
 
#else // defined(CYGPKG_DEVS_CAN_LPC2XXX_CAN0) && defined(CYGPKG_DEVS_CAN_LPC2XXX_CAN1)
#define N_A_MSG "Needs support for CAN channel 1 and 2"
#endif
 
#else // CYGFUN_KERNEL_API_C
#define N_A_MSG "Needs kernel C API"
#endif
 
#else // CYGPKG_IO_CAN && CYGPKG_KERNEL
#define N_A_MSG "Needs Kernel"
#endif
 
#ifdef N_A_MSG
void
cyg_start( void )
{
    CYG_TEST_INIT();
    CYG_TEST_NA(N_A_MSG);
}
#endif // N_A_MSG
 
//---------------------------------------------------------------------------
// EOF can_busload.c