Subversion Repositories openrisc

2009-03-23  John Dallaway  <john@dallaway.org.uk>

        * include/hal_platform_setup.h: Tweak LED manipulation routines to
        allow building for Thumb.

2009-01-31  Bart Veer <bartv@ecoscentric.com>

        * cdl/hal_arm_at91_eb40a.cdl: update compiler flags for gcc 4.x

2009-01-24  Bart Veer <bartv@ecoscentric.com>

        * cdl/hal_arm_at91_eb40a.cdl: switch from arm-elf-gcc to
        arm-eabi-gcc. Remove -mno-short-load-words.

2004-09-16  Andrea Michelotti <amichelotti@atmel.com>

        * include/hal_platform_ints.h: When CYGHWR_HAL_ARM_AT91_FIQ is defined 
          CYGNUM_HAL_ISR_MIN is equal to zero.
        
2004-08-30  Thomas Koeller <thomas.koeller@baslerweb.com>

        * cdl//hal_arm_at91_eb42.cdl: Undid last change. These
        options are not really common among all platforms.

2004-02-12  Jani Monoses <jani@iv.ro>

        * cdl/hal_arm_at91_eb40a.cdl: Move configuration options 
        common to all AT91 EB boards up to AT91 variant .cdl.
        
2003-12-16  Gary Thomas  <gary@mlbassoc.com>

        * misc/redboot_ROMRAM.ecm: 
        CYGNUM_FLASH_WORKSPACE_SIZE is no longer used.

2003-09-30 Jani Monoses <jani@iv.ro> 

        * cdl/hal_arm_at91_eb40a.cdl: Interfaces are already implemented by
        AT91 variant .cdl, do not duplicate them here.
        
2003-07-15  Jonathan Larmour  <jifl@eCosCentric.com>

        * include/hal_platform_ints.h (HAL_PLATFORM_RESET): Actually use
        hal_at91_reset_cpu().

2003-06-11  Oyvind Harboe  <oyvind.harboe@zylin.com>
        
        * src/eb40a_misc.c:
        LED routines were using the wrong bits.
        
        * include/plf_io.h
        LED defines were using the wrong bits
        Added defines for the EB40a board push buttons
        
2003-05-12  Nick Garnett  <nickg@balti.calivar.com>

        * src/eb40a_misc.c:
        Renamed and changed behaviour of led routines. They now all have
        hal_at91_ in front to prevent namespace pollution, and all now
        just take a simple 8 bit mask and adapt to the specific pin
        assignments internally.

        * cdl/hal_arm_at91_eb40a.cdl: Added requirement for
        CYGHWR_HAL_ARM_AT91 == "R40008" to customize the variant HAL to
        the device on this board.

        * include/hal_platform_setup.h: Added _led_init and _led macros to
        initialize and work board LEDs. Ensured that LEDs work even in RAM
        startup.

        * include/pkgconf/mlt_arm_at91_eb40a_ram.ldi: 
        * include/pkgconf/mlt_arm_at91_eb40a_ram.h: 
        * include/pkgconf/mlt_arm_at91_eb40a_rom.ldi: 
        * include/pkgconf/mlt_arm_at91_eb40a_rom.h: 
        * include/pkgconf/mlt_arm_at91_eb40a_romram.ldi: 
        * include/pkgconf/mlt_arm_at91_eb40a_romram.h:
        Changed RAM configuration to work only within the 256K of SRAM
        normally shipped with these boards.

2002-07-14  Tim Drury <tdrury@siliconmotorsports.com>

        * adapted from Thomas Koeller's <Thomas.Koeller@baslerweb.com> EB40
        patch to the original AT91 ecos base.  Fixed up FLASH, RAM, and SRAM
        sizes and locations throughout.  My EB40A board came with 1MB on-board
        SRAM although the docs state SRAM is NOT included, so this port
        reflects my on-board SRAM.
        * cdl/hal_arm_at91_eb40a.cdl - changed to 66MHz clock
        * include/hal_platform_setup.h - wait states for FLASH and SRAM are the
        same as EB40 (oddly enough).  The parts are faster but so is the AT91
        part, so the pre- and post-wait state numbers came out the same.
        * include/plf_io.h - added EB40A on-board LED definitions
        * include/pkgconf/* - changed all .h and .ldi files to reflect new
        FLASH, SRAM, and RAM sizes and locations.  NOTE: I do not use Windows
        so someone else will have to create the .mlt files that the GUI
        configuration tool needs to generate the .h and .ldi files.
        * misc/*.ecm - changed to use AT49LV1614 FLASH
        * src/eb40a_misc.c - added led_on(), led_off(), and get_leds()


//===========================================================================
// ####GPLCOPYRIGHTBEGIN####                                                
// -------------------------------------------                              
// This file is part of eCos, the Embedded Configurable Operating System.   
// Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003, 2009 Free Software Foundation, Inc.
//
// This program is free software; you can redistribute it and/or modify     
// it under the terms of the GNU General Public License as published by     
// the Free Software Foundation; either version 2 or (at your option) any   
// later version.                                                           
//
// This program is distributed in the hope that it will be useful, but      
// WITHOUT ANY WARRANTY; without even the implied warranty of               
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU        
// General Public License for more details.                                 
//
// You should have received a copy of the GNU General Public License        
// along with this program; if not, write to the                            
// Free Software Foundation, Inc., 51 Franklin Street,                      
// Fifth Floor, Boston, MA  02110-1301, USA.                                
// -------------------------------------------                              
// ####GPLCOPYRIGHTEND####                                                  
//===========================================================================