Subversion Repositories openrisc

/*==========================================================================
//
//      sam7ex256_misc.c
//
//      HAL misc board support code for Olimex SAM7-EX256 board
//
//==========================================================================
// ####ECOSGPLCOPYRIGHTBEGIN####                                            
// -------------------------------------------                              
// This file is part of eCos, the Embedded Configurable Operating System.   
// Copyright (C) 2006 Free Software Foundation, Inc.                        
//
// eCos is free software; you can redistribute it and/or modify it under    
// the terms of the GNU General Public License as published by the Free     
// Software Foundation; either version 2 or (at your option) any later      
// version.                                                                 
//
// eCos is distributed in the hope that it will be useful, but WITHOUT      
// ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or    
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License    
// for more details.                                                        
//
// You should have received a copy of the GNU General Public License        
// along with eCos; if not, write to the Free Software Foundation, Inc.,    
// 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.            
//
// As a special exception, if other files instantiate templates or use      
// macros or inline functions from this file, or you compile this file      
// and link it with other works to produce a work based on this file,       
// this file does not by itself cause the resulting work to be covered by   
// the GNU General Public License. However the source code for this file    
// must still be made available in accordance with section (3) of the GNU   
// General Public License v2.                                               
//
// This exception does not invalidate any other reasons why a work based    
// on this file might be covered by the GNU General Public License.         
// -------------------------------------------                              
// ####ECOSGPLCOPYRIGHTEND####                                              
//==========================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):    Uwe Kindler
// Contributors: Andrew Lunn, John Eigelaar
// Date:         2006-12-30
// Purpose:      HAL board support
// Description:  Implementations of HAL board interfaces
//
//####DESCRIPTIONEND####
//
//========================================================================*/
 
#include <pkgconf/system.h>
#include <pkgconf/hal.h>
 
#include <cyg/hal/hal_io.h>             // IO macros
 
//
// The development board does not contain any leds but a nokia 320 x 320 
// pixel lcd. We use the backlight of the lcd as a simple 1-bit LED
//
void hal_at91_led (int val)
{
    HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB20, AT91_PIN_OUT);
    HAL_ARM_AT91_GPIO_PUT(AT91_GPIO_PB20, (val & 1));
}
 
//
// Initialisation of Micrel KS8721 ethernet phy
//
void hal_plf_eth_init(void)
{
   cyg_uint32 stat;
 
   // Enable the PIOB Clock
   HAL_WRITE_UINT32(AT91_PMC + AT91_PMC_PCER, AT91_PMC_PCER_PIOB);
 
   // PU = Enables PCS_LPBK mode at power-up / reset.
   HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB15, AT91_PIN_IN);
   HAL_ARM_AT91_GPIO_CFG_PULLUP(AT91_GPIO_PB15, AT91_PIN_PULLUP_DISABLE);
 
   // PU = Enables ISOLATE mode at power-up /reset.
   HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB7, AT91_PIN_IN);
   HAL_ARM_AT91_GPIO_CFG_PULLUP(AT91_GPIO_PB7, AT91_PIN_PULLUP_DISABLE);
 
   // PU = Enables RMII mode at power-up / reset
   // TODO: The errata reports that the RMII mode for the SAM7X does not work.
   //      It would probably still be a good idea to use the RMII/MII CDL 
   //      configuration to select the appropriate mode here
   HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB16, AT91_PIN_IN);
   HAL_ARM_AT91_GPIO_CFG_PULLUP(AT91_GPIO_PB16, AT91_PIN_PULLUP_DISABLE);
 
   // PU = Enable RMII_BTB mode at power-up / reset.
   HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB4, AT91_PIN_IN);
   HAL_ARM_AT91_GPIO_CFG_PULLUP(AT91_GPIO_PB4, AT91_PIN_PULLUP_DISABLE);
 
   // Power Down Mode = 1 = normal operation
   HAL_ARM_AT91_GPIO_CFG_DIRECTION(AT91_GPIO_PB18, AT91_PIN_OUT);
   HAL_ARM_AT91_GPIO_PUT(AT91_GPIO_PB18, 1);
 
   // All the lines setup correctly. Now do a external reset and let the phy 
   // start up in the correct mode
   HAL_WRITE_UINT32(AT91_RST+AT91_RST_RMR,AT91_RST_RMR_KEY|(1<<0x8));
   HAL_WRITE_UINT32(AT91_RST+AT91_RST_RCR,AT91_RST_RCR_KEY|AT91_RST_RCR_EXTRST);
 
   do 
   {
     HAL_READ_UINT32(AT91_RST+AT91_RST_RSR,stat);
   } while (!(stat & AT91_RST_RSR_NRST_SET));
}
 
 
//--------------------------------------------------------------------------
// EOF sam7ex256_misc.c