Subversion Repositories openrisc

#ifndef CYGONCE_HAL_PLATFORM_SETUP_H
#define CYGONCE_HAL_PLATFORM_SETUP_H
 
/*=============================================================================
//
//      hal_platform_setup.h
//
//      Platform specific support for HAL (assembly code)
//
//=============================================================================
// ####ECOSGPLCOPYRIGHTBEGIN####                                            
// -------------------------------------------                              
// This file is part of eCos, the Embedded Configurable Operating System.   
// Copyright (C) 1998, 1999, 2000, 2001, 2002 Free Software Foundation, Inc.
//
// eCos is free software; you can redistribute it and/or modify it under    
// the terms of the GNU General Public License as published by the Free     
// Software Foundation; either version 2 or (at your option) any later      
// version.                                                                 
//
// eCos is distributed in the hope that it will be useful, but WITHOUT      
// ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or    
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License    
// for more details.                                                        
//
// You should have received a copy of the GNU General Public License        
// along with eCos; if not, write to the Free Software Foundation, Inc.,    
// 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.            
//
// As a special exception, if other files instantiate templates or use      
// macros or inline functions from this file, or you compile this file      
// and link it with other works to produce a work based on this file,       
// this file does not by itself cause the resulting work to be covered by   
// the GNU General Public License. However the source code for this file    
// must still be made available in accordance with section (3) of the GNU   
// General Public License v2.                                               
//
// This exception does not invalidate any other reasons why a work based    
// on this file might be covered by the GNU General Public License.         
// -------------------------------------------                              
// ####ECOSGPLCOPYRIGHTEND####                                              
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):    gthomas
// Contributors: gthomas
// Date:         2000-05-08
// Purpose:      Intel SA1110/Assabet platform specific support routines
// Description: 
// Usage:        #include <cyg/hal/hal_platform_setup.h>
//     Only used by "vectors.S"         
//
//####DESCRIPTIONEND####
//
//===========================================================================*/
 
#include <pkgconf/system.h>             // System-wide configuration info
#include CYGBLD_HAL_VARIANT_H           // Variant (SA11x0) specific configuration
#include CYGBLD_HAL_PLATFORM_H          // Platform specific configuration
#include <cyg/hal/hal_sa11x0.h>         // Variant specific hardware definitions
#include <cyg/hal/hal_mmu.h>            // MMU definitions
#include <cyg/hal/cerf.h>            // Platform specific hardware definitions
 
#if defined(CYG_HAL_STARTUP_ROM)
#define PLATFORM_SETUP1 _platform_setup1
#define CYGHWR_HAL_ARM_HAS_MMU
 
#if (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 59000)
#define SA11X0_PLL_CLOCK 0x0        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 73700)
#define SA11X0_PLL_CLOCK 0x1
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 88500)
#define SA11X0_PLL_CLOCK 0x2        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 103200) 
#define SA11X0_PLL_CLOCK 0x3        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 118000)
#define SA11X0_PLL_CLOCK 0x4        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 132700)
#define SA11X0_PLL_CLOCK 0x5        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 147500)
#define SA11X0_PLL_CLOCK 0x6        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 162200)
#define SA11X0_PLL_CLOCK 0x7        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 176900)
#define SA11X0_PLL_CLOCK 0x8        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 191700)
#define SA11X0_PLL_CLOCK 0x9        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 206400)
#define SA11X0_PLL_CLOCK 0xA        
#elif (CYGHWR_HAL_ARM_SA11X0_PROCESSOR_CLOCK == 221200)
#define SA11X0_PLL_CLOCK 0xB        
#else
#error Invalid processor clock speed
#endif
 
#define CAS0_WAVEFORM_VALUE	0xAAAAAA9F
#define CAS1_WAVEFORM_VALUE	0xAAAAAAAA
#define CAS2_WAVEFORM_VALUE	0xAAAAAAAA
 
#define MSC0VALUE		    0xFFFCFFFC
#define MSC1VALUE		    0xFFFFFFFF
#define MSC2VALUE		    0xFFFFFFFF
 
#define DRAM_CONFIG_VALUE	0x72547254
#define RFSH_CONFIG_VALUE	0x003002D1
 
// Macros that handle the red debug LED wired to GPIO-1
 
        .macro    _LED_ON,led
        ldr     r1,=SA11X0_GPIO_PIN_OUTPUT_SET
        mov     r0,#(1<<\led)
        str     r0,[r1]
        // Delay	
        ldr     r1,=10000
10:     sub     r1,r1,#1
        cmp     r1,#0
        bne     10b 
        .endm
 
        .macro    _LED_OFF,led
        ldr     r1,=SA11X0_GPIO_PIN_OUTPUT_CLEAR
        mov     r0,#(1<<\led)
        str     r0,[r1]
        // Delay	
        ldr     r1,=10000
10:     sub     r1,r1,#1
        cmp     r1,#0
        bne     10b 
        .endm
 
// This macro represents the initial startup code for the platform        
        .macro  _platform_setup1
 
        // Disable all interrupts (ICMR not specified on power-up)
        ldr     r1,=SA11X0_ICMR
        mov     r0,#0
        str     r0,[r1]
 
	    // Initialize the CPU.
		mov     r0, #0x0 		//  Get a zero to turn things off
		mcr     p15, 0, r0, c1, c0, 0 	//  MMU off
		mcr     p15, 0, r0, c8, c7, 0 	//  Flush TLB
		mcr     p15, 0, r0, c7, c7, 0 	//  Flush caches
		nop
		nop
		nop
        nop
 
        // Disable IRQs and FIQs
        mov     r0, #(CPSR_IRQ_DISABLE | \
                      CPSR_FIQ_DISABLE | \
                      CPSR_SUPERVISOR_MODE)
        msr     cpsr, r0
 
	    // Set up GPIOs (LED1 off)
        ldr     r1,=SA11X0_GPIO_PIN_DIRECTION
        ldr     r2,=0x0320000f          // Set LT1348,DREN,RXEN,CF and LEDs to be output
        str     r2,[r1]
        ldr     r3,=SA11X0_GPIO_PIN_OUTPUT_SET
        ldr     r2,=0x0300000f          // Set the LT1348,DREN,RXEN and LEDs to 1.
        str     r2,[r3] 
        ldr     r3,=SA11X0_GPIO_PIN_OUTPUT_CLEAR
        ldr     r2,=0x0020000f          // Set CF reset,LEDS OFF
        str     r2,[r3] 
 
        // Turn on LED 0
        _LED_ON 0
 
        // Disable clock switching
        mcr     p15,0,r0,\
                SA11X0_TEST_CLOCK_AND_IDLE_REGISTER,\
                SA11X0_DISABLE_CLOCK_SWITCHING_RM,\
                SA11X0_DISABLE_CLOCK_SWITCHING_OPCODE
 
        // Set up processor clock
        ldr     r1,=SA11X0_PWR_MGR_PLL_CONFIG
        ldr     r2,=SA11X0_PLL_CLOCK
        str     r2,[r1]
 
        // Turn clock switching back on
        mcr     p15,0,r0,\
                SA11X0_TEST_CLOCK_AND_IDLE_REGISTER,\
                SA11X0_ENABLE_CLOCK_SWITCHING_RM,\
                SA11X0_ENABLE_CLOCK_SWITCHING_OPCODE
        nop
        nop
 
        // Let the PLL settle down	
        ldr     r1,=20000
10:     sub     r1,r1,#1
        cmp     r1,#0
        bne     10b 
 
        // Turn on LED 1
        _LED_ON 1
 
        // Initialize DRAM controller
        ldr     r1,=dram_table
        ldr     r2,=__exception_handlers
        sub     r1,r1,r2
        ldr     r2,[r1],#4                      // First control register
10:     ldr     r3,[r1],#4
        str     r3,[r2]
        ldr     r2,[r1],#4                      // Next control register
        cmp     r2,#0
        bne     10b
 
        // Turn on LED 2
        _LED_ON 2
 
        // Enable UART
        ldr     r1,=SA1110_GPCLK_CONTROL_0
        ldr     r2,=SA1110_GPCLK_SUS_UART
        str     r2,[r1]
 
        // Release DRAM hold (set by RESET)
        ldr     r1,=SA11X0_PWR_MGR_SLEEP_STATUS
        ldr     r2,=SA11X0_DRAM_CONTROL_HOLD
        str     r2,[r1]
 
        // Perform 8 reads from unmapped/unenabled DRAM
        ldr     r1,=SA11X0_RAM_BANK0_BASE
	    ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
        ldr     r2,[r1]
 
	    // Enable DRAM bank 0
        ldr     r1,=SA11X0_DRAM_CONFIGURATION
        ldr     r2,=DRAM_CONFIG_VALUE
	    ldr     r3,=0x00030003
        orr     r2, r2, r3
        str     r2,[r1]
 
	    // Wait for the DRAM to come up.
        mov     r1, #0x400
0:	    subs    r1, r1, #1
        bne     0b
 
	    // Turn on LED 3
        _LED_ON 3
 
        b       19f
 
// DRAM controller initialization        
dram_table:
        .word   SA11X0_DRAM0_CAS_0,           CAS0_WAVEFORM_VALUE
        .word   SA11X0_DRAM0_CAS_1,           CAS1_WAVEFORM_VALUE
        .word   SA11X0_DRAM0_CAS_2,           CAS2_WAVEFORM_VALUE
        .word   SA11X0_DRAM2_CAS_0,           CAS0_WAVEFORM_VALUE
        .word   SA11X0_DRAM2_CAS_1,           CAS1_WAVEFORM_VALUE
        .word   SA11X0_DRAM2_CAS_2,           CAS2_WAVEFORM_VALUE
        .word   SA11X0_REFRESH_CONFIGURATION, RFSH_CONFIG_VALUE
        .word   SA11X0_DRAM_CONFIGURATION,    DRAM_CONFIG_VALUE 
	    .word   SA11X0_STATIC_CONTROL_0,      MSC0VALUE
	    .word   SA11X0_STATIC_CONTROL_1,      MSC1VALUE
	    .word   SA11X0_STATIC_CONTROL_2,      MSC2VALUE
	    .word   0, 0
 
19:
        // Wakeup from deep sleep mode
        ldr     r1,=SA11X0_RESET_STATUS
        ldr     r2,[r1]
        cmp     r2,#SA11X0_SLEEP_MODE_RESET
        bne     45f
        ldr     r1,=SA11X0_PWR_MGR_SCRATCHPAD
        ldr     r1,[r1]
        mov     pc,r1
        nop
45:     nop
 
        // Release peripheral hold (set by RESET)
        ldr     r1,=SA11X0_PWR_MGR_SLEEP_STATUS
        ldr     r2,=SA11X0_PERIPHERAL_CONTROL_HOLD
        str     r2,[r1]
 
        // Set up a stack [for calling C code]
        ldr     r1,=__startup_stack
        ldr     r2,=SA11X0_RAM_BANK0_BASE
        orr     sp,r1,r2
 
        // Create MMU tables
        bl      hal_mmu_init
 
        // Turn OFF LED 0 
        _LED_OFF 0
 
        // Enable MMU
        ldr     r2,=10f
       	ldr	    r1,=MMU_Control_Init|MMU_Control_M
	    mcr	    MMU_CP,0,r1,MMU_Control,c0
	    mov	    pc,r2    /* Change address spaces */
	    nop
 	    nop
	    nop
 
10:
        // Turn OFF LED 1 
        _LED_OFF 1
 
        // Save shadow copy of BCR, also hardware configuration
        ldr     r1,=_cerf_BCR
        str     r2,[r1]
        .endm
 
#else // defined(CYG_HAL_STARTUP_ROM)
#define PLATFORM_SETUP1
#endif
 
#define PLATFORM_VECTORS         _platform_vectors
        .macro  _platform_vectors
        .globl  _cerf_BCR
_cerf_BCR:   .long   0       // Board Control register shadow
        .endm                                        
 
/*---------------------------------------------------------------------------*/
/* end of hal_platform_setup.h                                               */
#endif /* CYGONCE_HAL_PLATFORM_SETUP_H */