URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [ecos-3.0/] [packages/] [hal/] [sh/] [edk7708/] [current/] [src/] [edk.S] - Rev 838
Go to most recent revision | Compare with Previous | Blame | View Log
##=============================================================================
##
## edk.S
##
## EDK board hardware setup
##
##=============================================================================
## ####ECOSGPLCOPYRIGHTBEGIN####
## -------------------------------------------
## This file is part of eCos, the Embedded Configurable Operating System.
## Copyright (C) 1998, 1999, 2000, 2001, 2002 Free Software Foundation, Inc.
##
## eCos is free software; you can redistribute it and/or modify it under
## the terms of the GNU General Public License as published by the Free
## Software Foundation; either version 2 or (at your option) any later
## version.
##
## eCos is distributed in the hope that it will be useful, but WITHOUT
## ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
## FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
## for more details.
##
## You should have received a copy of the GNU General Public License
## along with eCos; if not, write to the Free Software Foundation, Inc.,
## 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
##
## As a special exception, if other files instantiate templates or use
## macros or inline functions from this file, or you compile this file
## and link it with other works to produce a work based on this file,
## this file does not by itself cause the resulting work to be covered by
## the GNU General Public License. However the source code for this file
## must still be made available in accordance with section (3) of the GNU
## General Public License v2.
##
## This exception does not invalidate any other reasons why a work based
## on this file might be covered by the GNU General Public License.
## -------------------------------------------
## ####ECOSGPLCOPYRIGHTEND####
##=============================================================================
#######DESCRIPTIONBEGIN####
##
## Author(s): jskov
## Contributors:jskov
## Date: 1999-05-03
## Purpose: EDK7708 board hardware setup
## Description: This file contains any code needed to initialize the
## hardware on a Hitachi SH3 EDK7708 board.
##
######DESCRIPTIONEND####
##
##=============================================================================
#include <pkgconf/hal.h>
#include <cyg/hal/sh_regs.h>
.globl _hal_hardware_init
_hal_hardware_init:
// Set up the Bus State Controller
mov.l $BSC_settings_table,r3
1: mov.w @r3+,r0 // Address (or zero)
cmp/eq #0,r0
bt 2f
mov.w @r3+,r1 // data
bra 1b
mov.w r1,@r0 // delay slot
2:
rts
nop
.align 2
$BSC_settings_table:
.long BSC_settings_table
BSC_settings_table:
# These are the settings set by the Hitachi ROM Monitor.
# BCR2: Bus size of areas 1-6 to 32 bits
.word CYGARC_REG_BCR2
.word 0x3ffc
# BCR1: Areas 2 and 3 are SDRAM
.word CYGARC_REG_BCR1
.word 0x080c
# BCR2: Bus size of areas 1-6 to 32 bits [note: second write!]
.word CYGARC_REG_BCR2
.word 0x3ffc
# WCR1: 3 wait-state cycles inserted for all areas
.word CYGARC_REG_WCR1
.word 0x3fff
# WCR2: extra wait states and full pitch for burst
.word CYGARC_REG_WCR2
.word 0xffd7
# MCR: RAS/CAS & burst timing area 2/3
.word CYGARC_REG_MCR
.word 0x963c
#if 0
# DCR: RAS/CAS & burst timing area 2
.word CYGARC_REG_DCR
.word 0x0000
# PCR: PCMCIA disabled
.word CYGARC_REG_PCR
.word 0x0000
#endif
# RTCNT: refresh counter (needs a5 in top byte to accept write)
.word CYGARC_REG_RTCNT
.word (0xa500 | 0x0000)
# RTCOR: refresh time constant (needs a5 in top byte to accept write)
.word CYGARC_REG_RTCOR
.word (0xa500 | 0x003b)
# RFCR: refresh count register (needs a4 in top byte to accept write)
.word CYGARC_REG_RFCR
.word (0xa400 | 0x0000)
# RTCSR: refresh timer control (needs a5 in top byte to accept write)
.word CYGARC_REG_RTCSR
.word (0xa500 | 0x0008)
# Set SDMR to 0x220
.word 0xd880
.word 0
# Table end
.word 0
#------------------------------------------------------------------------------
# end of edk.S
Go to most recent revision | Compare with Previous | Blame | View Log