OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [ecos-3.0/] [packages/] [redboot/] [current/] [cdl/] [redboot.cdl] - Rev 786

Compare with Previous | Blame | View Log

# ====================================================================
#
#      redboot.cdl
#
#      Redboot package configuration data
#
# ====================================================================
## ####ECOSGPLCOPYRIGHTBEGIN####                                            
## -------------------------------------------                              
## This file is part of eCos, the Embedded Configurable Operating System.   
## Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2008, 2009 Free Software Foundation, Inc.
##
## eCos is free software; you can redistribute it and/or modify it under    
## the terms of the GNU General Public License as published by the Free     
## Software Foundation; either version 2 or (at your option) any later      
## version.                                                                 
##
## eCos is distributed in the hope that it will be useful, but WITHOUT      
## ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or    
## FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License    
## for more details.                                                        
##
## You should have received a copy of the GNU General Public License        
## along with eCos; if not, write to the Free Software Foundation, Inc.,    
## 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.            
##
## As a special exception, if other files instantiate templates or use      
## macros or inline functions from this file, or you compile this file      
## and link it with other works to produce a work based on this file,       
## this file does not by itself cause the resulting work to be covered by   
## the GNU General Public License. However the source code for this file    
## must still be made available in accordance with section (3) of the GNU   
## General Public License v2.                                               
##
## This exception does not invalidate any other reasons why a work based    
## on this file might be covered by the GNU General Public License.         
## -------------------------------------------                              
## ####ECOSGPLCOPYRIGHTEND####                                              
# ====================================================================
######DESCRIPTIONBEGIN####
#
# Author(s):      gthomas
# Original data:  gthomas
# Contributors:   Philippe Robin, Andrew Lunn, tkoeller
# Date:           2000-05-01
#
#####DESCRIPTIONEND####
#
# ====================================================================
cdl_package CYGPKG_REDBOOT {
    display       "Redboot ROM monitor"
    doc           redboot-guide/redboot-guide.html
    define_header redboot.h
    description   "
           This package supports the Redboot \[stand-alone debug monitor\]
           using eCos as the underlying board support mechanism."

    # Use of separate interrupt stack causes problems when running
    # programs as they can end up trashing RedBoot's stack
    requires { CYGIMP_HAL_COMMON_INTERRUPTS_USE_INTERRUPT_STACK == 0 }

    # Since the CYGDAT_REDBOOT_CONSOLE_DEV setting ends up in the platform
    # HAL header, we need to include that here (via hal.h).
    define_proc {
        puts $::cdl_header "#include <pkgconf/hal.h>"
    }

    cdl_component CYGSEM_REDBOOT_ELF {
        flavor bool
        display       "Include support for ELF file format"
        default_value 1

        cdl_option CYGOPT_REDBOOT_ELF_VIRTUAL_ADDRESS {
            display "Use the virtual address in the ELF headers"
            flavor bool
            default_value 0
            description "
                The ELF headers contain both a virtual and a physical address
                for where code/data should be loaded. By default the physical
                address is used but sometimes it is necassary to use the
                virtual address because of bugy toolchains"
        }
    }


    cdl_interface CYGINT_REDBOOT_LOAD_METHOD {
        display "Methods of loading images using redboot"
    }

    cdl_component CYGBLD_BUILD_REDBOOT {
        display "Build Redboot ROM ELF image"
        default_value 0
        requires CYGPKG_INFRA
        requires CYGPKG_ISOINFRA

        requires ! CYGDBG_HAL_DEBUG_GDB_CTRLC_SUPPORT
        requires ! CYGDBG_HAL_COMMON_INTERRUPTS_SAVE_MINIMUM_CONTEXT
        requires ! CYGDBG_HAL_COMMON_CONTEXT_SAVE_MINIMUM
        requires CYGSEM_HAL_VIRTUAL_VECTOR_SUPPORT
        requires CYGSEM_HAL_VIRTUAL_VECTOR_CLAIM_COMMS

        requires CYGINT_ISO_STRING_MEMFUNCS 
        requires CYGINT_ISO_STRING_STRFUNCS
        requires CYGINT_REDBOOT_LOAD_METHOD

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_GDB {
            display       "Include GDB support in RedBoot"
            no_define
            default_value 1
            active_if     CYGINT_HAL_DEBUG_GDB_STUBS
            requires      CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS
            requires      CYGDBG_HAL_DEBUG_GDB_BREAK_SUPPORT
            description "
              RedBoot normally includes support for the GDB debugging
              protocols. This option allows this to be disabled which
              may yield a substantial savings in terms of code and memory 
              usage by RedBoot."
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_THREADS {
            display "Threads debugging support"
            no_define
            description "
              Enabling this option will include special code in the
              GDB stubs to support debugging of threaded programs.  In
              the case of eCos programs, this support allows GDB to
              have complete access to the eCos threads in the
              program."
            active_if { CYG_HAL_STARTUP != "RAM" }
            requires  CYGDBG_HAL_DEBUG_GDB_THREAD_SUPPORT
        }

        cdl_option CYGDAT_REDBOOT_CUSTOM_VERSION {
            display        "Customized version string"
            flavor         booldata
            default_value  0
            description    "
              Use this option to define a customized version \"string\" for
              RedBoot.  Note: this value is only cosmetic, displayed by the
              \"version\" command, but is useful for providing site specific
              information about the RedBoot configuration."
        }

        cdl_option CYGNUM_REDBOOT_CMD_LINE_EDITING {
            display          "Enable command line editing"
            flavor           data
            default_value    16
            description      "
               If this option is non-zero, RedBoot will remember the
               last N command lines.  These lines may be reused.
               Enabling this history will also enable rudimentary
               editting of the lines themselves."
        }

        cdl_option CYGSEM_REDBOOT_CMD_LINE_ANSI_SEQUENCES {
            display          "Enable command line editing using ANSI arrows, etc"
            flavor           bool
            default_value    1
            active_if        CYGNUM_REDBOOT_CMD_LINE_EDITING != 0
            description      "
               If this option is enabled, RedBoot will accept standard ANSI key
               sequences for cursor movement (along with the emacs style keys)."
        }

        cdl_option CYGBLD_REDBOOT_CMD_LINE_HISTORY {
            display        "Enable history command and expansion"
            requires       { CYGNUM_REDBOOT_CMD_LINE_EDITING > 0 }
            flavor         bool
            default_value  1
            description  "
              Enabling this option will allow RedBoot to provide a
              history command to list previous commands. Also enables
              history expansion via '!'  character similar to bash
              shell."
        }

        cdl_option CYGBLD_REDBOOT_MAX_MEM_SEGMENTS {
            display        "Number of unique RAM segments on platform"
            flavor         data
            default_value  1
            description  "
              Change this option to be the number of memory segments which are
              supported by the platform.  If the value is greater than 1, then
              a platform specific function must provide information about the
              additional segments."
        }
    
        cdl_component CYGBLD_BUILD_REDBOOT_WITH_ZLIB {
            display       "Include support gzip/zlib decompression"
            active_if     CYGPKG_COMPRESS_ZLIB
            default_value 1
            implements    CYGINT_COMPRESS_ZLIB_LOCAL_ALLOC
            compile       decompress.c

            cdl_option CYGNUM_REDBOOT_LOAD_ZLIB_BUFFER {
                display       "Size of zlib decompression buffer"
                flavor        data
                default_value 64
                legal_values  5 to 256
                description   "
                    This is the size of the buffer filled with incoming data
                    during load before calls are made to the decompressor
                    function. For ethernet downloads this can be made bigger
                    (at the cost of memory), but for serial downloads on slow
                    processors it may be necessary to reduce the size to
                    avoid serial overruns. zlib appears to bail out if less 
                    than five bytes are available initially so this is the 
                    minimum."
            }
            cdl_option CYGPRI_REDBOOT_ZLIB_FLASH {
                 display       "Support compression of Flash images"
                 active_if     CYGPKG_REDBOOT_FLASH
                 active_if     !CYGSEM_IO_FLASH_READ_INDIRECT
                 calculated    1
                 description   "
                        This CDL indicates whether flash images can
                        be decompressed from gzip/zlib format into RAM."
            }

            cdl_option CYGBLD_BUILD_REDBOOT_WITH_GUNZIP {
                 display       "Include GZIP uncompress command"
                 default_value 0
                 description   "
                        Enable this option to include a 'gunzip' command 
                        to uncompress GZIP compressed data."
                 compile -library=libextras.a gunzip.c
            }
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_XYZMODEM {
            display       "Include support for xyzModem downloads"
            doc           ref/download-command.html
            no_define
            default_value 1
            implements    CYGINT_REDBOOT_LOAD_METHOD
            compile -library=libextras.a xyzModem.c
        }

        cdl_option CYGBLD_REDBOOT_LOAD_INTO_FLASH {
            display       "Allow the load-command write into Flash."
            default_value 0
            active_if     CYGPKG_REDBOOT_FLASH
            requires      CYGSEM_REDBOOT_VALIDATE_USER_RAM_LOADS
            compile       flash_load.c
            description "
                Write images direct to Flash via the load command.
                We assume anything which is invalid RAM is flash, hence
                the requires statement"
        }
        cdl_option CYGBLD_BUILD_REDBOOT_WITH_CKSUM {
            display       "Include POSIX checksum command"
            doc           ref/cksum-command.html
            default_value 1
            requires      CYGPKG_CRC
            compile -library=libextras.a cksum.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_MFILL {
            display       "Include memory fill command"
            doc           ref/mfill-command.html
            default_value 1
            compile -library=libextras.a mfill.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_MCMP {
            display       "Include memory compare command"
            doc           ref/mcmp-command.html
            default_value 1
            compile -library=libextras.a mcmp.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_MCOPY {
            display       "Include memory copy command"
            doc           ref/mcopy-command.html
            default_value 1
            compile -library=libextras.a mcopy.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_DUMP {
            display       "Include memory dump command"
            doc           ref/dump-command.html
            default_value 1
            compile -library=libextras.a dump.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_CACHES {
            display       "Include cache command"
            doc           ref/cache-command.html
            default_value 1
            compile -library=libextras.a caches.c
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_EXEC {
            display       "Include exec command"
            doc           ref/exec-command.html
            default_value 1
            # Implemented within the platform HAL
        }

        cdl_option CYGBLD_BUILD_REDBOOT_WITH_IOMEM {
            display       "Include I/O Memory commands 'iopeek' and 'iopoke'"
            default_value 0
            compile -library=libextras.a iomem.c
        }

        no_define
        description "
            This option enables the building of the Redboot ELF image.
            The image may require further relocation or symbol
            stripping before being converted to a binary image.
            This is handled by a rule in the target CDL."

    
        cdl_option CYGDBG_REDBOOT_TICK_GRANULARITY {
            display          "Granularity of timer/ticks"
            flavor           data
            legal_values     { 50 100 250 500 1000 }    
            default_value    250
            description      "
                This option controls the granularity of the timers.
                Faster CPUs can afford higher granularity (lower values)
                which should give higher network performance since the stack
                is purely polled."
        }

        compile main.c
        compile misc_funs.c io.c parse.c ticks.c syscall.c alias.c
        compile -library=libextras.a load.c

        make -priority 320 {
            <PREFIX>/bin/redboot.elf : $(PREFIX)/lib/target.ld $(PREFIX)/lib/vectors.o $(PREFIX)/lib/libtarget.a $(PREFIX)/lib/libextras.a
                    @sh -c "mkdir -p $(dir $@)"
                    $(CC) -c $(INCLUDE_PATH) $(ACTUAL_CFLAGS) -o $(PREFIX)/lib/version.o $(REPOSITORY)/$(PACKAGE)/src/version.c
                    $(CC) $(LDFLAGS) -L$(PREFIX)/lib -Ttarget.ld -o $@ $(PREFIX)/lib/version.o
        }

        cdl_component CYGPKG_REDBOOT_NETWORKING {
            display       "Redboot Networking"
            flavor        bool
            active_if     CYGPKG_IO_ETH_DRIVERS
            default_value 1
            implements    CYGINT_REDBOOT_LOAD_METHOD
            compile net/udp.c net/ip.c net/pktbuf.c net/cksum.c
            compile net/enet.c net/icmp.c net/tcp.c net/timers.c net/arp.c
            compile net/inet_addr.c
            compile -library=libextras.a net/ping.c net/net_io.c 
            description "This option includes networking support in RedBoot."
            define_proc {
                puts $::cdl_system_header "#define CYGNUM_HAL_VIRTUAL_VECTOR_AUX_CHANNELS 1"
            }
    
            cdl_option CYGDBG_REDBOOT_NET_DEBUG {
                display          "Print net debug information"
                flavor           bool
                default_value    0
                description      "
                    This option is overriden by the configuration stored 
                    in flash."
            }
    
            cdl_option CYGSEM_REDBOOT_NET_TFTP_DOWNLOAD {
                display          "Support TFTP for download"
                flavor           bool
                default_value    1
                compile          -library=libextras.a net/tftp_client.c
                description      "
                    This option enables the use of the TFTP protocol for 
                    download"
            }
    
            cdl_option CYGSEM_REDBOOT_NET_HTTP_DOWNLOAD {
                display          "Support HTTP for download"
                flavor           bool
                default_value    1
                compile          -library=libextras.a net/http_client.c
                description      "
                    This option enables the use of the HTTP protocol for 
                    download"
            }
    
            cdl_component CYGDAT_REDBOOT_DEFAULT_IP_ADDR {
                display          "Default IP address"
                flavor           booldata
                default_value    CYGSEM_REDBOOT_FLASH_CONFIG ? 0 : \
                                    { "0, 0, 0, 0" }
                description      "
                    This IP address is the default used by RedBoot if
                    a BOOTP/DHCP server does not respond. The numbers
                    should be separated by *commas*, and not dots. If
                    an IP address is configured into the Flash
                    configuration, that will be used in preference."
    
                cdl_option CYGDAT_REDBOOT_DEFAULT_BOOTP_SERVER_IP_ADDR {
                     display           "Default bootp server"
                     flavor            booldata
                     default_value     CYGSEM_REDBOOT_FLASH_CONFIG ? 0 : \
                                          { "0, 0, 0, 0" }
                     description       "
                          This IP address is the default server
                          address used by RedBoot if a BOOTP/DHCP
                          server does not respond. The numbers should
                          be separated by *commas*, and not dots. If
                          an IP address is configured into the Flash
                          configuration, that will be used in
                          preference."
                }
            }

            cdl_component CYGPKG_REDBOOT_NETWORKING_BOOTP {
                display          "Enable BOOTP/DHCP support"
                flavor           bool
                default_value    1
                compile          net/bootp.c
                description      "
                    Use BOOTP/DHCP protocol to obtain pertinent IP
                    addresses, such as the client, server, gateway,
                    etc."
                
                cdl_component CYGSEM_REDBOOT_NETWORKING_DHCP {
                    display          "Enable DHCP in addition to BOOTP support"
                    flavor           bool
                    default_value    1
                    description      "
                    Enables DHCP protocol in addition to BOOTP.  If not enabled,
                    only BOOTP will be suported."
                }

                cdl_component CYGSEM_REDBOOT_NETWORKING_BOOTP_VERBOSE {
                    display          "Enable verbose output from BOOTP/DHCP code"
                    flavor           bool
                    default_value    0
                    description      "
                    Enable more verbose output from BOOTP/DHCP that logs rx/tx
                    packet types and state-machine transitions."
                }

                cdl_option CYGSEM_REDBOOT_DEFAULT_NO_BOOTP {
                    display          "Do not try to use BOOTP/DHCP"
                    flavor           bool
                    default_value    0
                    description      "
                         By default Redboot tries to use BOOTP/DHCP to
                         get an IP address when BOOTP/DHCP support is
                         present in Redboot. If there's no BOOTP/DHCP
                         server on your network use this option to
                         avoid waiting for the BOOTP/DHCP timeouts and
                         retries. This option is overriden by the
                         configuration stored in flash."
                }
            }

            cdl_component CYGSEM_REDBOOT_NETWORKING_USE_GATEWAY {
                display          "Use a gateway for non-local IP traffic"
                flavor           bool
                default_value    1
                description      "
                  Enabling this option will allow the RedBoot networking
                stack to use a \[single\] gateway to reach a non-local
                IP address.  If disabled, RedBoot will only be able to
                reach nodes on the same subnet."
    
                cdl_component CYGDAT_REDBOOT_DEFAULT_GATEWAY_IP_ADDR {
                    display          "Default gateway IP address"
                    flavor           booldata
                    default_value    CYGSEM_REDBOOT_FLASH_CONFIG ? 0 : \
                                        { "0, 0, 0, 0" }
                    description      "
                        This IP address is the default used by RedBoot
                        if a BOOTP/DHCP server does not respond. The
                        numbers should be separated by *commas*, and
                        not dots. If an IP address is configured into
                        the Flash configuration, that will be used in
                        preference."
                }
    
                cdl_component CYGDAT_REDBOOT_DEFAULT_IP_ADDR_MASK {
                    display          "Default IP address mask"
                    flavor           booldata
                    default_value    CYGSEM_REDBOOT_FLASH_CONFIG ? 0 : \
                                        { "255, 255, 255, 0" }
                    description      "
                        This IP address mask is the default used by
                        RedBoot if a BOOTP/DHCP server does not
                        respond. The numbers should be separated by
                        *commas*, and not dots. If an IP address is
                        configured into the Flash configuration, that
                        will be used in preference."
                }
            }
    
            cdl_option CYGNUM_REDBOOT_NETWORKING_TCP_PORT {
                display          "TCP port to listen for incoming connections"
                flavor           data
                default_value    9000
                description      "
                   RedBoot will 'listen' on this port for incoming TCP 
                   connections. This allows outside connections to be made 
                   to the platform, either for GDB or RedBoot commands."
            }
    
            cdl_option CYGNUM_REDBOOT_NETWORKING_MAX_PKTBUF {
                display          "Number of \[network\] packet buffers"
                flavor           data
                default_value    4
                legal_values     3 to 8
                description      "
                   RedBoot may need to buffer network data to support
                   various connections.  This option allows control
                   over the number of such buffered packets, and in
                   turn, controls the amount of memory used by RedBoot
                   (which is not available to user applications).
                   Each packet buffer takes up about 1514 bytes.
                   Note: there is little need to make this larger than
                   the default."
            }
    
            cdl_component CYGPKG_REDBOOT_NETWORKING_DNS {
                display         "DNS support"
                default_value   1
                active_if       CYGPKG_NS_DNS
                requires        !CYGPKG_NS_DNS_BUILD
                compile         net/dns.c
                description     "
                    When this option is enabled, RedBoot will be built with
                    support for DNS, allowing use of hostnames on the command
                    line."
            
                cdl_option CYGPKG_REDBOOT_NETWORKING_DNS_IP {
                    display         "Default DNS IP"
                    flavor          data
                    active_if       !CYGSEM_REDBOOT_FLASH_CONFIG
                    default_value   { "0.0.0.0" }
                    description "
                      This option sets the IP of the default DNS. The IP can be
                      changed at runtime as well."
                }

                cdl_option CYGNUM_REDBOOT_NETWORKING_DNS_TIMEOUT {
                    display         "Timeout in DNS lookup"
                    flavor          data
                    default_value   10
                    description "
                      This option sets the timeout used when looking up an
                      address via the DNS. Default is 10 seconds."
                }
    
                cdl_component CYGPKG_REDBOOT_NETWORKING_DNS_WITH_DOMAIN {
                    display         "Support the use of a domain name"
                    flavor          bool
                    default_value   0
                    description     "
                       This option controls if Redboot supports domain
                       names when performing DNS lookups"
                       
                    cdl_option    CYGPKG_REDBOOT_NETWORKING_DNS_DEFAULT_DOMAIN {
                        display         "Default DNS domain"
                        flavor          booldata
                        default_value   0
                        description "
                            This option sets the default DNS domain name.
                            This value will be overwritten by the value in
                            flash or a domain returned by DHCP"
                    }

                    cdl_option    CYGPKG_REDBOOT_NETWORKING_DNS_FCONFIG_DOMAIN {
                        display         "Get DNS domain from Flash"
                        flavor          bool
                        active_if       CYGSEM_REDBOOT_FLASH_CONFIG
                        default_value   0
                        description "
                            This option enables getting the domain name 
                            from the flash configuration. This can later be 
                            overwritten by a value learnt from DHCP"
                    }

                    cdl_option    CYGPKG_REDBOOT_NETWORKING_DNS_DHCP_DOMAIN {
                        display         "Use DNS domain from DHCP"
                        flavor          bool
                        default_value   0
                        description "
                            This option enables the use of the domain name
                            returned by DHCP."
                    }

                    cdl_option CYGNUM_REDBOOT_NETWORK_DNS_DOMAIN_BUFSIZE {
                        display         "BOOTP/DHCP DNS domain buffer size"
                        flavor          data
                        default_value   32
                        description "
                           This options sets the size of the static
                           buffer used by BOOTP/DHCP to store the DNS
                           domain name. The domain name will not be
                           set if the buffer is too small to hold it."
                    }
                }
            }

            cdl_option CYGDAT_REDBOOT_DEFAULT_NETWORK_DEVICE {
                display         "Default network device driver"
                flavor          data
                active_if       { CYGHWR_NET_DRIVERS > 1 }
                default_value   { "\"\"" }
                description     "
                    This is the name of the default network device to use."
            }

            cdl_option CYGSEM_REDBOOT_NETWORK_INIT_ONE_DEVICE {
                display         "Initialize only one net device"
                flavor          bool
                active_if       { CYGHWR_NET_DRIVERS > 1 }
                default_value   0
                description     "
                    This option tells RedBoot to stop initializing network
                    devices when it finds the first device which is
                    successfully initialized. The default behavior causes
                    all network devices to be initialized."
            }
        }
    
        cdl_option CYGPKG_REDBOOT_ANY_CONSOLE {
            display       "Let RedBoot use any I/O channel for its console."
            flavor        bool
            default_value 1
            description   "
              If this option is enabled then RedBoot will attempt to use all
              defined serial I/O channels for its console device.  Once input
              arrives at one of these channels then the console will use only
              that port."
        }
    
        cdl_option CYGSEM_REDBOOT_VARIABLE_BAUD_RATE {
            display       "Let RedBoot adjust the baud off the serial console."
            flavor        bool
            default_value 1
            active_if     CYGINT_HAL_VIRTUAL_VECTOR_COMM_BAUD_SUPPORT
            description   "
              If this option is enabled then RedBoot will support commands 
              to set and query the baud rate on the selected console."     
        }
    
        cdl_option CYGSEM_REDBOOT_PLF_STARTUP {
            display       "Run a platform specific startup function."
            flavor        bool
            default_value 0
            description   "
              If this option is enabled then RedBoot will execute a platform
              specific startup function before entering into its command line
              processing.  This allows the platform to perform any special
              setups before RedBoot actually starts running.  Note: the entire
              RedBoot environment will already be initialized at this point."
        }
    
        cdl_option CYGSEM_REDBOOT_PLF_ESA_VALIDATE {
            display       "Run a platform specific ESA validation function."
            flavor        bool
            default_value 0
            description   "
              If this option is enabled then RedBoot will execute a platform
              specific function to validate an ethernet ESA.  This would be
              useful if the address must conform to standards set by the
              hardware manufacturer, etc."
        }
    
        cdl_option CYGPKG_REDBOOT_MAX_CMD_LINE {
            display       "Maximum command line length"
            flavor        data
            default_value 256
            description   "
              This option allows control over how long the CLI command line
              should be.  This space will be allocated statically
              rather than from RedBoot's stack."
        }
    
        cdl_option CYGNUM_REDBOOT_CLI_IDLE_TIMEOUT {
            display       "Command processing idle timeout (ms)"
            flavor        data
            default_value 10
            description   "
              This option controls the timeout period before the
              command processing is considered 'idle'.  Making this
              number smaller will cause idle processing to take place
              more often, etc.  The default value of 10ms is a reasonable
              tradeoff between responsiveness and overhead."
        }
    
        cdl_option CYGSEM_REDBOOT_VALIDATE_USER_RAM_LOADS {
            display       "Validate RAM addresses during load"
            flavor        bool
            default_value 1
            description   "

              This option controls whether or not RedBoot will make
              sure that memory being used by the \"load\" command is
              in fact in user RAM.  Leaving the option enabled makes
              for a safer environment, but this check may not be valid
              on all platforms, thus the ability to disable it.  
              ** Disable this only with great care **"
        }
    
        cdl_option CYGNUM_REDBOOT_FLASH_BASE {
            display       "Base address of flash device redboot should use"
            flavor        booldata
            description   "
                This option controls how redboot finds the flash
                device. Setting this option to an address will
                cause redboot to use that address as the base of the 
                flash device."
        }

        cdl_component CYGPKG_REDBOOT_FLASH {
            display       "Allow RedBoot to support FLASH programming"
            flavor        bool
            default_value 1
            active_if     CYGHWR_IO_FLASH_DEVICE
            description   "
              If this option is enabled then RedBoot will provide commands
              to manage images in FLASH memory.  These images can be loaded
              into memory for execution or executed in place."
            compile -library=libextras.a flash.c
    
            cdl_option CYGOPT_REDBOOT_FLASH_BYTEORDER {
                display         "Byte order used to store info in flash."
                flavor          data
                default_value   { "NATURAL" }
                legal_values    {"NATURAL" "MSBFIRST" "LSBFIRST" }
                description "
                    This option controls the byte ordering used to store
                    the FIS directory info and flash config info."
            }
    
            cdl_option CYGOPT_REDBOOT_FIS {
                display         "RedBoot Flash Image System support"
                default_value   1
                doc             ref/flash-image-system.html
                description "
                    This option enables the Flash Image System commands
                    and support within RedBoot.  If disabled, simple Flash
                    access commands such as \"fis write\" will still exist.
                    This option would be disabled for targets that need simple
                    FLASH manipulation, but do not have the need or space for
                    complete image management."
            }

            cdl_option CYGDAT_REDBOOT_FIS_MAX_FREE_CHUNKS {
                display        "Max number of chunks of free space to manage"
                flavor         booldata
                default_value  32
                description    "

                  If this option is defined then \"fis free\" will
                  rely on the FIS directory to determine what space is
                  free within the FLASH.  This option controls the
                  maximum number of free segment which can be handled
                  (typically this number is small).  If this option is
                  not enabled, the the archaic behaviour of actually
                  scanning the FLASH for erased sectors (unreliable)
                  will be used to determine what's free and what's
                  not."
            }
    
            cdl_component CYGPKG_REDBOOT_FIS_CONTENTS {
                display       "Flash Image System default directory contents"
                active_if     CYGOPT_REDBOOT_FIS
                calculated    1
    
                cdl_option CYGNUM_REDBOOT_FIS_DIRECTORY_BLOCK {
                    display         "Flash block containing the Directory"
                    flavor          data
                    default_value   (-1)
                    description "
                      Which block of flash should hold the directory
                      information. Positive numbers are absolute block
                      numbers.  Negative block numbers count backwards
                      from the last block.  eg 2 means block 2, -2
                      means the last but one block."
                }
    
                cdl_component CYGOPT_REDBOOT_REDUNDANT_FIS {
                    display         "Redundant Flash Image System Directory Support"
                    default_value   0
                    requires { 0 == CYGSEM_REDBOOT_FLASH_COMBINED_FIS_AND_CONFIG }
                    description "
                              This option enables the use of a redundant FIS
                              directory within RedBoot.  If enabled a flash block
                              will be reserved for a second copy of the fis
                              directory. Doing this allow for power failure safe
                              updates of the directory by the application."
      
                    cdl_option CYGNUM_REDBOOT_FIS_REDUNDANT_DIRECTORY_BLOCK {
                        display         "Flash block containing the backup Directory"
                        flavor          data
                        default_value   (-3)
                        requires { CYGNUM_REDBOOT_FIS_REDUNDANT_DIRECTORY_BLOCK !=
                                   CYGNUM_REDBOOT_FIS_DIRECTORY_BLOCK }
                        description "
                                 Which block of flash should hold the redundant
                                 directory information. Positive numbers are
                                 absolute block numbers. Negative block numbers
                                 count backwards from the last block. eg 2 means
                                 block 2, -2 means the last but one block."
                    }
                }
    
                cdl_option CYGOPT_REDBOOT_FIS_RESERVED_BASE {
                    display         "Pseudo-file to describe reserved area"
                    active_if       { 0 != CYGNUM_REDBOOT_FLASH_RESERVED_BASE }
                    default_value   1
                    description "
                        If an area of FLASH is reserved, it is informative to
                        have a fis entry describing it.  This option controls
                        creation of such an entry by default in the fis init
                        command."
                }
    
                cdl_option CYGOPT_REDBOOT_FIS_REDBOOT {
                    display         "File to describe RedBoot boot image"
                    default_value   1
                    description "
                        Normally a ROM-startup RedBoot image is first in the
                        FLASH, and the system boots using that image.  This
                        option controls creation of an entry describing it in
                        the fis init command.  It might be disabled if a
                        platform has an immutable boot image of its own, where
                        we use a POST-startup RedBoot instead, which performs
                        less board initialization."
                }
    
                cdl_component CYGOPT_REDBOOT_FIS_REDBOOT_POST {
                    display         "File to describe RedBoot POST-compatible image"
                    default_value   !CYGOPT_REDBOOT_FIS_REDBOOT
                    description "
                        This option controls creation of an entry describing a
                        POST-startup RedBoot image in the fis init command.
                        Not all platforms support POST-startup.  A platform
                        might have both for testing purposes, where the
                        eventual user would substitute their own POST code for
                        the initial ROM-startup RedBoot, and then jump to the
                        POST-compatible RedBoot immediately following."
                    cdl_option CYGNUM_REDBOOT_FIS_REDBOOT_POST_OFFSET {
                        display    "Offset of POST image from FLASH start"
                        flavor     booldata
                        default_value 0
                        requires   { CYGNUM_REDBOOT_FIS_REDBOOT_POST_OFFSET >= \
                                     CYGBLD_REDBOOT_FLASH_BOOT_OFFSET }
                        description "
                        This option specifies the offset for a POST image from
                        the start of FLASH.  If unset, then the fis entry
                        describing the POST image will be placed where
                        convenient."
                    }
                }   
    
                cdl_option CYGOPT_REDBOOT_FIS_REDBOOT_BACKUP {
                    display         "File to describe RedBoot backup image"
                    default_value   0
                    description "
                        This option controls creation of an entry describing a
                        backup RedBoot image in the fis init command.
                        Conventionally a RAM-startup RedBoot image is kept
                        under this name for use in updating the ROM-based
                        RedBoot that boots the board."
                }
    
                cdl_option CYGOPT_REDBOOT_FIS_DIRECTORY_ARM_SIB_ID {
                    display         "Include ARM SIB ID in FIS"
                    default_value   0
                    description "
                      If set, this option will cause the last 5 words of
                      the FIS to include the special ID needed for the
                      flash to be recognized as a reserved area for RedBoot
                      by an ARM BootRom monitor."
                }
    
                cdl_option CYGNUM_REDBOOT_FIS_DIRECTORY_ENTRY_SIZE {
                    display         "Size of FIS directory entry"
                    flavor              data
                    default_value   256
                    description "
                      The FIS directory is limited to one single flash
                      sector. If your flash has tiny sectors, you may wish
                      to reduce this value in order to get more slots in
                      the FIS directory."
                }
    
                cdl_option CYGNUM_REDBOOT_FIS_DIRECTORY_ENTRY_COUNT {
                    display         "Number of FIS directory entries"
                    flavor          data
                    default_value   8
                    description "
                      The FIS directory normally occupies a single flash
                      sector. Adjusting this value can allow for more than
                      one flash sector to be used, which is useful if your
                      sectors are very small."
                }
    
                cdl_option CYGBLD_REDBOOT_MIN_IMAGE_SIZE {
                    display       "Maximum RedBoot image size"
                    flavor        data
                    default_value { CYGOPT_REDBOOT_FIS_REDBOOT ? 0x20000 : 0 }
                    description "
                      This option controls the maximum length reserved
                      for the RedBoot boot image in the FIS table.
                      This should be a multiple of the flash's erase
                      block size."
                }
        
                cdl_option CYGBLD_REDBOOT_FLASH_BOOT_OFFSET {
                    display       "Offset from start of FLASH to RedBoot boot image"
                    flavor        data
                    default_value CYGNUM_REDBOOT_FLASH_RESERVED_BASE
                    requires      { CYGNUM_REDBOOT_FLASH_RESERVED_BASE <= \
                                    CYGBLD_REDBOOT_FLASH_BOOT_OFFSET }
                    description "
                      This option controls where the RedBoot boot image is 
                      located relative to the start of FLASH."
                }
        
                cdl_option CYGNUM_REDBOOT_FLASH_RESERVED_BASE {
                    display       "Size of reserved area at start of FLASH"
                    flavor        data
                    default_value 0
                    description "
                      This option reserves an area at the start of
                      FLASH where RedBoot will never interfere; it is
                      expected that this area contains
                      (non-RedBoot-based) POST code or some other boot
                      monitor that executes before RedBoot."
                }

                cdl_option CYGNUM_REDBOOT_FLASH_RESERVED_DEVICES {
                    display         "List of Flash devices that are reserved"
                    flavor          booldata
                    default_value   0
                    description     "This option lists the base addresses of any Flash
                                     devices that should not be managed by the flash
                                     image system. In particular, this means that these
                                     devices will not be considered when looking for free
                                     space in which to create new files. It should consist
                                     of a comma-separated list of (virtual) addresses."
                }
            }
    
            cdl_option CYGSEM_REDBOOT_FLASH_LOCK_SPECIAL {
                display       "Keep all RedBoot FLASH data blocks locked."
                flavor        bool
                default_value 1
                active_if     { CYGHWR_IO_FLASH_BLOCK_LOCKING != 0 }
                description "
                  When this option is enabled, RedBoot will keep configuration
                  data and the FIS directory blocks implicitly locked.  While
                  this is somewhat safer, it does add overhead during updates."
            }
    
            cdl_option CYGSEM_REDBOOT_FIS_CRC_CHECK {
                display       "Use CRC checksums on FIS images."
                flavor        bool
                default_value 1
                requires      CYGPKG_CRC
                description "
                  When this option is enabled, RedBoot will use CRC checksums
                  when reading and writing flash images."
            }
    
            cdl_interface CYGINT_REDBOOT_ARM_FLASH_SIB_SUPPORTED {
                display       "ARM FLASH drivers support SIB flash block structure"
                active_if     CYGPKG_HAL_ARM
                description   "This interface is implemented by a flash driver
                               to indicate that it supports the ARM SIB flash
                               block structure"
            }
    
            cdl_option CYGHWR_REDBOOT_ARM_FLASH_SIB {
                display       "Use ARM SIB flash block structure"
                flavor        bool
                active_if     CYGINT_REDBOOT_ARM_FLASH_SIB_SUPPORTED
                default_value 1
                description "
                  This option is used to interpret ARM Flash System 
                  information blocks."
            }
        }
    
        cdl_component CYGSEM_REDBOOT_FLASH_CONFIG {
            display       "Keep RedBoot configuration data in FLASH"
            flavor        bool
            default_value { CYGPKG_IO_FLASH != 0 }
            compile       fconfig.c
            description "
              When this option is enabled, RedBoot will keep configuration
              data in a separate block of FLASH memory.  This data will
              include such items as the node IP address or startup scripts."

            cdl_option CYGNUM_REDBOOT_FLASH_CONFIG_SIZE {
                display       "Length of configuration data in FLASH"
                flavor        data
                default_value 4096
                description "
                  This option is used to control the amount of memory and FLASH
                  to be used for configuration options (persistent storage)."
            }

            cdl_option CYGHWR_REDBOOT_FLASH_CONFIG_MEDIA {
                display       "Style of media used for persistent data storage"
                flavor        data
                legal_values  { "FLASH" "EEPROM" }
                default_value { "FLASH" }
                description "
                  Persistent data storage can either be held in 'norma' FLASH
                  or some other device (represented by the 'EEPROM' choice).
                  The different styles utilize different access methods."
            }

            cdl_option CYGSEM_REDBOOT_FLASH_COMBINED_FIS_AND_CONFIG {
                display       "Merged config data and FIS directory"
                flavor        bool              
                active_if     { CYGOPT_REDBOOT_FIS && \
                               (CYGHWR_REDBOOT_FLASH_CONFIG_MEDIA == "FLASH") }
                default_value 1
                description "
                  If this option is set, then the FIS directory and FLASH 
                  configuration database will be stored in the same physical
                  FLASH block."
            }

            cdl_option CYGNUM_REDBOOT_FLASH_CONFIG_BLOCK {
                display       "Which block of flash to use" 
                flavor         data
                default_value  (-2)
                description "
                  Which block of flash should hold the configuration 
                  information. Positive numbers are absolute block numbers. 
                  Negative block numbers count backwards from the last block.
                  eg 2 means block 2, -2 means the last but one block."
            }

            cdl_option CYGSEM_REDBOOT_FLASH_ALIASES {
                display       "Support simple macros/aliases in FLASH"
                flavor        bool
                default_value 1
                description "
                  This option is used to allow support for simple text-based
                  macros (aliases).  These aliases are kept in the FLASH
                  configuration data (persistent storage)."
            }

            cdl_option CYGNUM_REDBOOT_FLASH_STRING_SIZE {
                display       "Length of strings in FLASH configuration data"
                flavor        data
                default_value 128
                description "
                  This option is used to control the amount of memory
                  and FLASH to be used for string configuration
                  options (persistent storage)."
            }

            cdl_option CYGNUM_REDBOOT_FLASH_SCRIPT_SIZE {
                display       "Length of configuration script(s) in FLASH"
                flavor        data
                default_value 512
                description "
                  This option is used to control the amount of memory and 
                  FLASH to be used for configuration options (persistent 
                  storage)."
            }

            cdl_option CYGSEM_REDBOOT_FLASH_CONFIG_READONLY_FALLBACK {
                display       "Fallback to read-only FLASH configuration"
                flavor        bool
                default_value { (CYGHWR_REDBOOT_FLASH_CONFIG_MEDIA == "FLASH") }
                description "
                  This option will cause the configuration information to
                  revert to the readonly information stored in the FLASH.
                  The option only takes effect after 
                    1) the config_ok flag has been set to be true,
                       indicating that at one time the copy in RAM was valid;
                  and
                    2) the information in RAM has been verified to be invalid"
                  
            }
        }
    
        cdl_component CYGPKG_REDBOOT_FILEIO {
            display       "Allow RedBoot to support fileio"
            flavor        bool
            default_value 1
            active_if     CYGPKG_IO_FILEIO
            requires      CYGPKG_IO
            description   "
              If this option is enabled then RedBoot will provide commands
              to load files from fileio file systems such as JFFS2."
            compile -library=libextras.a fs/fileio.c

            cdl_option CYGBLD_REDBOOT_FILEIO_WITH_LS {
                display       "Include an ls command"
                flavor        bool
                default_value 1
                description   "
                   If this option is enabled a simple ls command will be
                   included in redboot so the contents of a directory
                   can be listed"
            }
        }

        cdl_component CYGPKG_REDBOOT_DISK {
            display       "Allow RedBoot to support disks"
            flavor        bool
            default_value 1
            description   "
              If this option is enabled then RedBoot will provide commands
              to load disk files."

            cdl_option CYGSEM_REDBOOT_DISK {
                display   "Include Redboot commands for disk access"
                default_value { CYGINT_REDBOOT_DISK_DRIVERS != 0 }
                compile -library=libextras.a fs/disk.c
            }

            cdl_interface CYGINT_REDBOOT_DISK_DRIVERS {
                display  "Hardware drivers for disk-type devices"
            }
    
            cdl_option CYGNUM_REDBOOT_MAX_DISKS {
                display       "Maximum number of supported disks"
                flavor        data
                default_value 4
                description "
                  This option controls the number of disks supported by 
                  RedBoot."
            }
    
            cdl_option CYGNUM_REDBOOT_MAX_PARTITIONS {
                display       "Maximum number of partitions per disk"
                flavor        data
                default_value 8
                description "
                  This option controls the maximum number of supported 
                  partitions per disk."
            }
    
            cdl_component CYGSEM_REDBOOT_DISK_IDE {
                display       "Support IDE disks."
                flavor        bool
                default_value 1
                active_if     { CYGINT_HAL_PLF_IF_IDE != 0 }
                description "
                  When this option is enabled, RedBoot will support IDE disks."
                compile -library=libextras.a fs/ide.c
                implements    CYGINT_REDBOOT_DISK_DRIVERS

                cdl_option CYGSEM_REDBOOT_DISK_IDE_VMWARE {
                    display       "Work with VMware virtual disks"
                    flavor        bool
                    default_value 0
                    description "
                        This option controls the disk driver behavior at 
                        ide-init"
                }
            }
    
            cdl_component CYGSEM_REDBOOT_DISK_EXT2FS {
                display       "Support Linux second extended filesystems."
                flavor        bool
                default_value 1
                description "
                  When this option is enabled, RedBoot will support EXT2 
                  filesystems."
                compile -library=libextras.a fs/e2fs.c
            }
    
            cdl_component CYGSEM_REDBOOT_DISK_ISO9660 {
                display       "Support ISO9660 filesystems."
                flavor        bool
                calculated    0
                description "
                  When this option is enabled, RedBoot will support ISO9660 
                  filesystems."
                compile -library=libextras.a fs/iso9660fs.c
            }
        }
    
        cdl_component CYGPKG_REDBOOT_BOOT_SCRIPT {
            display         "Boot scripting"
            doc             ref/persistent-state-flash.html
            flavor          none
            no_define
            description     "
                    This contains options related to RedBoot's boot script
                    functionality."
            
            cdl_option CYGFUN_REDBOOT_BOOT_SCRIPT {
                    display         "Boot scripting enabled"
                    flavor          bool
                    active_if       { CYGDAT_REDBOOT_DEFAULT_BOOT_SCRIPT || \
                                      CYGSEM_REDBOOT_FLASH_CONFIG }
                    calculated      1
                    description "
                      This option controls whether RedBoot boot script
                      functionality is enabled." 
            }
    
            cdl_option CYGDAT_REDBOOT_DEFAULT_BOOT_SCRIPT {
                    display         "Use default RedBoot boot script"
                    flavor          booldata
                    default_value   0
                    description "
                      If enabled, this option will tell RedBoot to use the 
                      value of this option as a default boot script."
            }
    
            cdl_option CYGNUM_REDBOOT_BOOT_SCRIPT_TIMEOUT_RESOLUTION {
                display       "Resolution (in ms) for script timeout value."
                flavor        data
                default_value 1000
                description "
                  This option controls the resolution of the script
                  timeout.  The value is specified in milliseconds
                  (ms), thus to have the script timeout be defined in
                  terms of tenths of seconds, use 100."    
            }
    
            cdl_option CYGNUM_REDBOOT_BOOT_SCRIPT_DEFAULT_TIMEOUT {
                display       "Script default timeout value"
                flavor        data
                default_value 10
                description "
                  This option is used to set the default timeout for startup
                  scripts, when they are enabled."
            }
        }
    
        cdl_option CYGSEM_REDBOOT_RTC {
            display      "Support RTC for time & date functions"
            active_if    { CYGPKG_IO_WALLCLOCK }
            default_value 1
            description  "
              When this option is enabled, RedBoot will support commands to
              query and set the real time clock (time and date)"
            compile -library=libextras.a time_date.cxx
        }
    
        cdl_option CYGPRI_REDBOOT_ROM_MONITOR {
            display      "Behave like a ROM monitor"
            active_if    { CYG_HAL_STARTUP == "ROM" || \
                           CYG_HAL_STARTUP == "ROMRAM" }
            requires     CYGSEM_HAL_ROM_MONITOR
            calculated   1
            no_define
            description  "
              Enabling this option will allow RedBoot to provide ROM 
              monitor-style services to programs which it executes."
        }
    
        cdl_component CYGSEM_REDBOOT_BSP_SYSCALLS {
            display       "Allow RedBoot to handle GNUPro application 'syscalls'."
            flavor        bool
            default_value 0
            description   "
              If this option is enabled then RedBoot will install a
              syscall handler to support debugging of applications
              based on GNUPro newlib/bsp."
    
            cdl_option CYGSEM_REDBOOT_BSP_SYSCALLS_GPROF {
                display "Support additional syscalls for 'gprof' profiling"
                flavor  bool
                default_value 1
                active_if       { 0 < CYGINT_REDBOOT_BSP_SYSCALLS_GPROF_SUPPORT }
                description "
                    Support additional syscalls to support a periodic callback
                    function for histogram-style profiling, and an enquire/set
                    of the tick rate.
                    The application must use the GNUPro newlib facilities
                    to set this up."
            }
    
            cdl_interface CYGINT_REDBOOT_BSP_SYSCALLS_GPROF_SUPPORT {
                display "Does the HAL support 'gprof' profiling?"
                no_define
            }

            cdl_option CYGOPT_REDBOOT_BSP_SYSCALLS_EXIT_WITHOUT_TRAP {
                display "Do not raise SIGTRAP when program exits"
                default_value 0
                description "
                    For some (single shot) newlib based programs,
                    exiting and returning a termination status may be
                    the normal expected behavior."
            }
        }
    
        cdl_component CYGOPT_REDBOOT_FIS_ZLIB_COMMON_BUFFER {
            display             "Use a common buffer for Zlib and FIS"
            flavor              bool
            active_if           { CYGBLD_BUILD_REDBOOT_WITH_ZLIB && \
                              CYGOPT_REDBOOT_FIS }
            default_value       0
            description         "
                Use a common memory buffer for both the zlib workspace
                and FIS directory operations. This can save a substantial
                amount of RAM, especially when flash sectors are large."
    
            cdl_option CYGNUM_REDBOOT_FIS_ZLIB_COMMON_BUFFER_SIZE {
                display             "Size of Zlib/FIS common buffer"
                flavor              data
                default_value   0xc000
                legal_values    0x4000 to 0x80000000
                description     "
                    Size of common buffer to allocate. Must be at least the
                    size of one flash sector."
            }
        }

        cdl_component CYGMEM_REDBOOT_WORKSPACE_HEAP {
            display             "Allocate heap in RedBoot workspace"
            flavor              bool
            active_if           CYGPKG_MEMALLOC
            active_if           CYGPKG_MEMALLOC_MALLOC_ALLOCATORS
            default_value       0
            description         "
                    If the MEMALLOC package is present, it usually allocates
                    the whole of memory not used by the program to the heap.
                    In RedBoot this is not a good idea, since we need space to
                    load application programs. Setting this option causes RedBoot
                    to allocate the heap at the top of RAM by reserving part of
                    RedBoot's workspace memory, leaving the rest of memory free."

            cdl_option CYGMEM_REDBOOT_WORKSPACE_HEAP_SIZE {
                display         "Size of RedBoot heap"
                flavor          data
                default_value   0x10000
                legal_values    0x4000 to 0x80000000
                description     "
                    Size of RedBoot heap. This defines how much memory is to be
                    allocated for the heap."
            }
        }

        cdl_option CYGNUM_REDBOOT_GETC_BUFFER {
            display       "Buffer size in getc when loading images"
            flavor        data
            default_value { CYGPKG_REDBOOT_FILEIO ? 4096 : 256 }
            description   "
                When loading images a buffer is used between redboot and the
                underlying storage medium, eg a filesystem, or a socket etc.
                The size of this buffer can have a big impart on load speed."
        }

    }
}

# EOF redboot.cdl

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.