OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [ARM7_STR75x_GCC/] [serial/] [serial.c] - Rev 578

Go to most recent revision | Compare with Previous | Blame | View Log

/*
    FreeRTOS V6.1.1 - Copyright (C) 2011 Real Time Engineers Ltd.
 
    ***************************************************************************
    *                                                                         *
    * If you are:                                                             *
    *                                                                         *
    *    + New to FreeRTOS,                                                   *
    *    + Wanting to learn FreeRTOS or multitasking in general quickly       *
    *    + Looking for basic training,                                        *
    *    + Wanting to improve your FreeRTOS skills and productivity           *
    *                                                                         *
    * then take a look at the FreeRTOS books - available as PDF or paperback  *
    *                                                                         *
    *        "Using the FreeRTOS Real Time Kernel - a Practical Guide"        *
    *                  http://www.FreeRTOS.org/Documentation                  *
    *                                                                         *
    * A pdf reference manual is also available.  Both are usually delivered   *
    * to your inbox within 20 minutes to two hours when purchased between 8am *
    * and 8pm GMT (although please allow up to 24 hours in case of            *
    * exceptional circumstances).  Thank you for your support!                *
    *                                                                         *
    ***************************************************************************
 
    This file is part of the FreeRTOS distribution.
 
    FreeRTOS is free software; you can redistribute it and/or modify it under
    the terms of the GNU General Public License (version 2) as published by the
    Free Software Foundation AND MODIFIED BY the FreeRTOS exception.
    ***NOTE*** The exception to the GPL is included to allow you to distribute
    a combined work that includes FreeRTOS without being obliged to provide the
    source code for proprietary components outside of the FreeRTOS kernel.
    FreeRTOS is distributed in the hope that it will be useful, but WITHOUT
    ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
    FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
    more details. You should have received a copy of the GNU General Public 
    License and the FreeRTOS license exception along with FreeRTOS; if not it 
    can be viewed here: http://www.freertos.org/a00114.html and also obtained 
    by writing to Richard Barry, contact details for whom are available on the
    FreeRTOS WEB site.
 
    1 tab == 4 spaces!
 
    http://www.FreeRTOS.org - Documentation, latest information, license and
    contact details.
 
    http://www.SafeRTOS.com - A version that is certified for use in safety
    critical systems.
 
    http://www.OpenRTOS.com - Commercial support, development, porting,
    licensing and training services.
*/
 
/*
	BASIC INTERRUPT DRIVEN SERIAL PORT DRIVER FOR UART0.
*/
 
 
/*-----------------------------------------------------------
 * Components that can be compiled to either ARM or THUMB mode are
 * contained in this file.c  The ISR routines, which can only be compiled
 * to ARM mode, are contained in serialISR.c.
 *----------------------------------------------------------*/
 
 
 
/* Library includes. */
#include "75x_uart.h"
#include "75x_gpio.h"
#include "75x_eic.h"
#include "75x_mrcc.h"
 
/* Scheduler includes. */
#include "FreeRTOS.h"
#include "queue.h"
 
/* Demo application includes. */
#include "serial.h"
 
#define serINVALID_QUEUE				( ( xQueueHandle ) 0 )
#define serNO_BLOCK						( ( portTickType ) 0 )
 
/*-----------------------------------------------------------*/
 
/* Queues used to hold received characters, and characters waiting to be
transmitted. */
static xQueueHandle xRxedChars;
static xQueueHandle xCharsForTx;
 
static volatile portBASE_TYPE xQueueEmpty = pdTRUE;
 
/*-----------------------------------------------------------*/
 
/* The interrupt service routine - called from the assembly entry point. */
void vSerialISR( void );
void vConfigureQueues( xQueueHandle xQForRx, xQueueHandle xQForTx, volatile portBASE_TYPE *pxEmptyFlag );
 
/*-----------------------------------------------------------*/
 
/*
 * See the serial2.h header file.
 */
xComPortHandle xSerialPortInitMinimal( unsigned long ulWantedBaud, unsigned portBASE_TYPE uxQueueLength )
{
xComPortHandle xReturn;
UART_InitTypeDef UART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
EIC_IRQInitTypeDef  EIC_IRQInitStructure;	
 
	/* Create the queues used to hold Rx and Tx characters. */
	xRxedChars = xQueueCreate( uxQueueLength, ( unsigned portBASE_TYPE ) sizeof( signed char ) );
	xCharsForTx = xQueueCreate( uxQueueLength + 1, ( unsigned portBASE_TYPE ) sizeof( signed char ) );
 
	/* If the queues were created correctly then setup the serial port
	hardware. */
	if( ( xRxedChars != serINVALID_QUEUE ) && ( xCharsForTx != serINVALID_QUEUE ) )
	{
 
		vConfigureQueues( xRxedChars, xCharsForTx, &xQueueEmpty );
 
		portENTER_CRITICAL();
		{
			/* Enable the UART0 Clock. */
			MRCC_PeripheralClockConfig( MRCC_Peripheral_UART0, ENABLE );
 
			/* Configure the UART0_Tx as alternate function */
			GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
			GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_11;
			GPIO_Init(GPIO0, &GPIO_InitStructure);
 
			/* Configure the UART0_Rx as input floating */
			GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
			GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
			GPIO_Init(GPIO0, &GPIO_InitStructure);
 
			/* Configure UART0. */
			UART_InitStructure.UART_WordLength = UART_WordLength_8D;
			UART_InitStructure.UART_StopBits = UART_StopBits_1;
			UART_InitStructure.UART_Parity = UART_Parity_No;
			UART_InitStructure.UART_BaudRate = ulWantedBaud;
			UART_InitStructure.UART_HardwareFlowControl = UART_HardwareFlowControl_None;
			UART_InitStructure.UART_Mode = UART_Mode_Tx_Rx;
			UART_InitStructure.UART_TxFIFOLevel = UART_FIFOLevel_1_2; /* FIFO size 16 bytes, FIFO level 8 bytes */
			UART_InitStructure.UART_RxFIFOLevel = UART_FIFOLevel_1_2; /* FIFO size 16 bytes, FIFO level 8 bytes */
			UART_Init(UART0, &UART_InitStructure);
 
			/* Enable the UART0 */
			UART_Cmd(UART0, ENABLE);
 
			/* Configure the IEC for the UART interrupts. */			
			EIC_IRQInitStructure.EIC_IRQChannelCmd = ENABLE;
			EIC_IRQInitStructure.EIC_IRQChannel = UART0_IRQChannel;
			EIC_IRQInitStructure.EIC_IRQChannelPriority = 1;
			EIC_IRQInit(&EIC_IRQInitStructure);
 
			xQueueEmpty = pdTRUE;
			UART_ITConfig( UART0, UART_IT_Transmit | UART_IT_Receive, ENABLE );
		}
		portEXIT_CRITICAL();
	}
	else
	{
		xReturn = ( xComPortHandle ) 0;
	}
 
	/* This demo file only supports a single port but we have to return
	something to comply with the standard demo header file. */
	return xReturn;
}
/*-----------------------------------------------------------*/
 
signed portBASE_TYPE xSerialGetChar( xComPortHandle pxPort, signed char *pcRxedChar, portTickType xBlockTime )
{
	/* The port handle is not required as this driver only supports one port. */
	( void ) pxPort;
 
	/* Get the next character from the buffer.  Return false if no characters
	are available, or arrive before xBlockTime expires. */
	if( xQueueReceive( xRxedChars, pcRxedChar, xBlockTime ) )
	{
		return pdTRUE;
	}
	else
	{
		return pdFALSE;
	}
}
/*-----------------------------------------------------------*/
 
void vSerialPutString( xComPortHandle pxPort, const signed char * const pcString, unsigned short usStringLength )
{
signed char *pxNext;
 
	/* A couple of parameters that this port does not use. */
	( void ) usStringLength;
	( void ) pxPort;
 
	/* NOTE: This implementation does not handle the queue being full as no
	block time is used! */
 
	/* The port handle is not required as this driver only supports UART0. */
	( void ) pxPort;
 
	/* Send each character in the string, one at a time. */
	pxNext = ( signed char * ) pcString;
	while( *pxNext )
	{
		xSerialPutChar( pxPort, *pxNext, serNO_BLOCK );
		pxNext++;
	}
}
/*-----------------------------------------------------------*/
 
signed portBASE_TYPE xSerialPutChar( xComPortHandle pxPort, signed char cOutChar, portTickType xBlockTime )
{
portBASE_TYPE xReturn;
 
	/* Place the character in the queue of characters to be transmitted. */
	portENTER_CRITICAL();
	{
		if( xQueueEmpty == pdTRUE )
		{
			UART0->DR = cOutChar;
			xReturn = pdPASS;
		}
		else
		{
			if( xQueueSend( xCharsForTx, &cOutChar, xBlockTime ) != pdPASS )
			{
				xReturn = pdFAIL;
			}			
			else
			{
				xReturn = pdPASS;				
			}
		}
 
		xQueueEmpty = pdFALSE;
	}
	portEXIT_CRITICAL();
 
	return xReturn;
}
/*-----------------------------------------------------------*/
 
void vSerialClose( xComPortHandle xPort )
{
	/* Not supported as not required by the demo application. */
}
/*-----------------------------------------------------------*/
 
 
 
 
 
 
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.