OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [CORTEX_AT91SAM3U256_IAR/] [system/] [board.h] - Rev 580

Compare with Previous | Blame | View Log

/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support
 * ----------------------------------------------------------------------------
 * Copyright (c) 2008, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */
 
//------------------------------------------------------------------------------
/// \dir
/// !Purpose
///
/// Definition and functions for using AT91SAM3UE-related features, such
/// has PIO pins, memories, etc.
///
/// !Usage
/// -# The code for booting the board is provided by board_cstartup.S and
///    board_lowlevel.c.
/// -# For using board PIOs, board characteristics (clock, etc.) and external
///    components, see board.h.
/// -# For manipulating memories (remapping, SDRAM, etc.), see board_memories.h.
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \unit
/// !Purpose
///
/// Definition of AT91SAM3UE-EK characteristics, AT91SAM3UE-dependant PIOs and
/// external components interfacing.
///
/// !Usage
/// -# For operating frequency information, see "SAM3UE-EK - Operating frequencies".
/// -# For using portable PIO definitions, see "SAM3UE-EK - PIO definitions".
/// -# Several USB definitions are included here (see "SAM3UE-EK - USB device").
//------------------------------------------------------------------------------
 
#ifndef BOARD_H
#define BOARD_H
 
//------------------------------------------------------------------------------
//         Headers
//------------------------------------------------------------------------------
 
#if defined(at91sam3u4)
    #include "at91sam3u4/chip.h"
    #include "at91sam3u4/AT91SAM3U4.h"
#else
    #error Board does not support the specified chip.
#endif
 
//------------------------------------------------------------------------------
//         Definitions
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - Board Description"
/// This page lists several definition related to the board description.
///
/// !Definitions
/// - BOARD_NAME
 
/// Name of the board.
#define BOARD_NAME "AT91SAM3U-EK"
/// Board definition.
#define at91sam3uek
/// Family definition (already defined).
#define at91sam3u
/// Core definition
#define cortexm3
// Chip type
//#define fpgasimulation
//------------------------------------------------------------------------------
 
#if defined(fpgasimulation)
#define PMC_BY_HARD
#endif
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - Operating frequencies"
/// This page lists several definition related to the board operating frequency
/// (when using the initialization done by board_lowlevel.c).
///
/// !Definitions
/// - BOARD_MAINOSC
/// - BOARD_MCK
 
/// Frequency of the board main oscillator.
#define BOARD_MAINOSC           12000000
 
/// Master clock frequency (when using board_lowlevel.c).
#if !defined(fpgasimulation)
#define BOARD_MCK               48000000
#else
#define BOARD_MCK               22579200
#endif
 
#if defined (fpgasimulation)
//#define BOARD_ConfigureSdram(...) { }
#endif // fpgasimulation
 
//------------------------------------------------------------------------------
// ADC
//------------------------------------------------------------------------------
/// ADC clock frequency, at 10-bit resolution (in Hz)
#define ADC_MAX_CK_10BIT         5000000
/// Startup time max, return from Idle mode (in µs)
#define ADC_STARTUP_TIME_MAX       15
/// Track and hold Acquisition Time min (in ns)
#define ADC_TRACK_HOLD_TIME_MIN  1200
 
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - USB device"
/// This page lists constants describing several characteristics (controller
/// type, D+ pull-up type, etc.) of the USB device controller of the chip/board.
///
/// !Constants
/// - BOARD_USB_UDP
/// - BOARD_USB_PULLUP_EXTERNAL
/// - BOARD_USB_NUMENDPOINTS
/// - BOARD_USB_ENDPOINTS_MAXPACKETSIZE
/// - BOARD_USB_ENDPOINTS_BANKS
 
/// Chip has a UDP controller.
#define BOARD_USB_UDPHS
 
/// Indicates the D+ pull-up is external.
#define BOARD_USB_PULLUP_INTERNAL
 
/// Number of endpoints in the USB controller.
#define BOARD_USB_NUMENDPOINTS              7
 
/// Returns the maximum packet size of the given endpoint.
#define BOARD_USB_ENDPOINTS_MAXPACKETSIZE(i) (((i == 0)||(i == 3)||(i == 4)) ? 64 :\
                                             (((i == 1) || (i == 2)) ? 512 : 1024))
 
/// Returns the number of FIFO banks for the given endpoint.
#define BOARD_USB_ENDPOINTS_BANKS(i)        ((i == 0) ? 1 : ((i == 1) || (i == 2)) ? 2 : 3)
 
/// USB attributes configuration descriptor (bus or self powered, remote wakeup)
#define BOARD_USB_BMATTRIBUTES              USBConfigurationDescriptor_SELFPOWERED_RWAKEUP
//#define BOARD_USB_BMATTRIBUTES            USBConfigurationDescriptor_SELFPOWERED_NORWAKEUP
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - PIO definitions"
/// This pages lists all the pio definitions contained in board.h. The constants
/// are named using the following convention: PIN_* for a constant which defines
/// a single Pin instance (but may include several PIOs sharing the same
/// controller), and PINS_* for a list of Pin instances.
///
/// !ADC
/// - PIN_ADC0_AD0
/// - PIN_ADC0_AD1
/// - PIN_ADC0_AD2
/// - PIN_ADC0_AD3
/// - PIN_ADC0_AD4
/// - PIN_ADC0_AD5
/// - PIN_ADC0_AD6
/// - PIN_ADC0_AD7
/// - PINS_ADC0
///
/// !CAN
/// - PIN_CAN_TRANSCEIVER_RS
/// - PIN_CAN1_TRANSCEIVER_TXD
/// - PIN_CAN1_TRANSCEIVER_RXD
/// - PIN_CAN2_TRANSCEIVER_TXD
/// - PIN_CAN2_TRANSCEIVER_RXD
/// - PINS_CAN_TRANSCEIVER_TXD
/// - PINS_CAN_TRANSCEIVER_RXD
///
/// !DBGU
/// - PINS_DBGU
///
/// !Joystick buttons
/// - PIN_JOYSTICK_UP
/// - PIN_JOYSTICK_DOWN
/// - PIN_JOYSTICK_LEFT
/// - PIN_JOYSTICK_RIGHT
/// - PIN_JOYSTICK_LCLIC, PIN_JOYSTICK_PUSH
/// - PINS_JOYSTICK_MOVE, PINS_JOYSTICK_CLIC, PINS_JOYSTICK
/// - JOYSTICK_UP
/// - JOYSTICK_DOWN
/// - JOYSTICK_LEFT
/// - JOYSTICK_RIGHT
/// - JOYSTICK_LCLIC, JOYSTICK_PUSH
///
/// !EBI
/// - PIN_EBI_DATA_BUS
/// - PIN_EBI_NCS0
/// - PIN_EBI_NRD
/// - PIN_EBI_NWE
/// - PIN_EBI_ADDR_BUS
/// - PIN_EBI_PSRAM_NBS
/// - PIN_EBI_A1
/// - PIN_EBI_LCD_RS
///
/// !LEDs
/// - PIN_LED_DS1
/// - PIN_LED_DS2
/// - PIN_LED_DS3
/// - PIN_LED_DS4
/// - PINS_LEDS
/// - LED_DS1
/// - LED_DS2
/// - LED_DS3
/// - LED_DS4
///
/// !MCI
/// - PINS_MCI
///
/// !Push buttons
/// - PIN_PUSHBUTTON_1
/// - PIN_PUSHBUTTON_2
/// - PIN_PUSHBUTTON_3
/// - PIN_PUSHBUTTON_4
/// - PINS_PUSHBUTTONS
/// - PUSHBUTTON_BP1
/// - PUSHBUTTON_BP2
/// - PUSHBUTTON_BP3
/// - PUSHBUTTON_BP4
///
/// !PWMC
/// - PIN_PWMC_PWM0
/// - PIN_PWMC_PWM1
/// - PIN_PWMC_PWM2
/// - PIN_PWMC_PWM3
/// - PIN_PWMC_PWM4
/// - PIN_PWMC_PWM5
/// - PIN_PWMC_PWM6
/// - PIN_PWMC_PWM7
/// - PIN_PWM_LED0
/// - PIN_PWM_LED1
/// - CHANNEL_PWM_LED0
/// - CHANNEL_PWM_LED1
///
/// !SPI0
/// - PIN_SPI0_MISO
/// - PIN_SPI0_MOSI
/// - PIN_SPI0_SPCK
/// - PINS_SPI0
/// - PIN_SPI0_NPCS3
///
/// !SPI1
/// - PIN_SPI1_MISO
/// - PIN_SPI1_MOSI
/// - PIN_SPI1_SPCK
/// - PINS_SPI1
/// - PIN_SPI1_NPCS3
///
/// ! SSC
/// - PIN_SSC_TD
/// - PIN_SSC_TK
/// - PIN_SSC_TF
/// - PINS_SSC_CODEC
///
/// ! PCK0
/// - PIN_PCK0
///
/// !TWI
/// - PIN_TWI_TWD0
/// - PIN_TWI_TWCK0
/// - PINS_TWI
///
/// !USART0
/// - PIN_USART0_RXD
/// - PIN_USART0_TXD
/// - PIN_USART0_CTS
/// - PIN_USART0_RTS
/// - PIN_USART0_SCK
///
/// !USB
/// - PIN_USB_PULLUP
///
 
/// ADC_AD0 pin definition.
#define PIN_ADC0_AD0 {1 << 21, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD1 pin definition.
#define PIN_ADC0_AD1 {1 << 30, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD2 pin definition.
#define PIN_ADC0_AD2 {1 << 3, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD3 pin definition.
#define PIN_ADC0_AD3 {1 << 4, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD4 pin definition.
#define PIN_ADC0_AD4 {1 << 15, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD5 pin definition.
#define PIN_ADC0_AD5 {1 << 16, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD6 pin definition.
#define PIN_ADC0_AD6 {1 << 17, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_INPUT, PIO_DEFAULT}
/// ADC_AD7 pin definition.
#define PIN_ADC0_AD7 {1 << 18, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_INPUT, PIO_DEFAULT}
 
/// Pins ADC
#define PINS_ADC PIN_ADC0_AD0, PIN_ADC0_AD1, PIN_ADC0_AD2, PIN_ADC0_AD3, PIN_ADC0_AD4, PIN_ADC0_AD5, PIN_ADC0_AD6, PIN_ADC0_AD7
 
/// CAN Definition
/// RS: Select input for high speed mode or silent mode
//#define PIN_CAN_TRANSCEIVER_RS  {1<<23, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
//
///// TXD: Transmit data input
//#define PIN_CAN1_TRANSCEIVER_TXD  {1<<27, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
///// RXD: Receive data output
//#define PIN_CAN1_TRANSCEIVER_RXD  {1<<26, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// TXD: Transmit data input
//#define PIN_CAN2_TRANSCEIVER_TXD  {1<<29, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
///// RXD: Receive data output
//#define PIN_CAN2_TRANSCEIVER_RXD  {1<<28, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
///// TXD pins
//#define PINS_CAN_TRANSCEIVER_TXD  PIN_CAN1_TRANSCEIVER_TXD, PIN_CAN2_TRANSCEIVER_TXD
///// RXD pins
//#define PINS_CAN_TRANSCEIVER_RXD  PIN_CAN1_TRANSCEIVER_RXD, PIN_CAN2_TRANSCEIVER_RXD
 
/// DBGU pins (DTXD and DRXD) definitions, PA11,12.
#define PINS_DBGU  {0x00001800, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
 
/// EBI
#define PIN_EBI_DATA_BUS            {0xfe01fe00, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}, \
                                        {1 << 6, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_B, PIO_PULLUP}
#define PIN_EBI_NCS0                {1 << 20, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_NRD                 {1 << 19, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_NWE                 {1 << 23, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_PSRAM_ADDR_BUS      {0x3f00fff, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_PSRAM_NBS           {1 << 7, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_B, PIO_PULLUP}, \
                                        {1 << 15, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_A1                  {1 << 8, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_B, PIO_PULLUP}
 
#define PIN_EBI_NCS2                {1 << 16, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_LCD_RS              {1 << 8, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_B, PIO_PULLUP}
 
 
/// LED #0 pin definition.
#define PIN_LED_0   {1 << 0, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT}
/// LED #1 pin definition.
#define PIN_LED_1   {1 << 2, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_OUTPUT_1, PIO_DEFAULT}
/// LED #2 pin definition.
#define PIN_LED_2   {1 << 1, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_OUTPUT_1, PIO_DEFAULT}
/// List of all LEDs definitions.
#define PINS_LEDS   PIN_LED_0, PIN_LED_1, PIN_LED_2
 
///// MCI pins definition.
#define PINS_MCI  {0x1f8, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_PULLUP}, \
                      {1 << 3, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
 
/// MCI pin Card Detect
#define PIN_MCI_CD \
    {AT91C_PIO_PA25, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_PULLUP}
 
/// Push button #0 definition.
#define PIN_PUSHBUTTON_1    {1 << 18, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_DEGLITCH | PIO_PULLUP}
/// Push button #1 definition.
#define PIN_PUSHBUTTON_2    {1 << 19, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_DEGLITCH | PIO_PULLUP}
/// Push button #2 definition
/// List of all push button definitions.
#define PINS_PUSHBUTTONS    PIN_PUSHBUTTON_1, PIN_PUSHBUTTON_2
 
/// Push button #1 index.
#define PUSHBUTTON_BP1   0
/// Push button #2 index.
#define PUSHBUTTON_BP2   1
 
/// Simulated joystick LEFT index.
#define JOYSTICK_LEFT       0
/// Simulated joystick RIGHT index.
#define JOYSTICK_RIGHT      1
 
/// SPI0 MISO pin definition.
#define PIN_SPI0_MISO  {1 << 13, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// SPI0 MOSI pin definition.
#define PIN_SPI0_MOSI  {1 << 14, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// SPI0 SPCK pin definition.
#define PIN_SPI0_SPCK  {1 << 15, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/// SPI0 chip select 2 pin definition.
//#define PIN_SPI0_NPCS2_PC14  {1 <<  14, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT}
#define PIN_SPI0_NPCS2_PC14  {1 <<  14, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_OUTPUT_0, PIO_PULLUP}
/// List of SPI0 pin definitions (MISO, MOSI & SPCK).
#define PINS_SPI0      PIN_SPI0_MISO, PIN_SPI0_MOSI, PIN_SPI0_SPCK
 
/// SSC pins definition.
#define PIN_SSC_TD      {0x1 << 26, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SSC_TK      {0x1 << 28, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SSC_TF      {0x1 << 30, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PINS_SSC_CODEC       PIN_SSC_TD,  PIN_SSC_TK, PIN_SSC_TF
 
/// PCK0
#define PIN_PCK0        {0x1 << 21, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
 
/// TWI pins definition.
#define TWI_V3XX
#define PIN_TWI_TWD0    {0x1 << 9, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_TWI_TWCK0    {0x1 << 10, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PINS_TWI0     PIN_TWI_TWD0, PIN_TWI_TWCK0
#define PIN_TWI_TWD1    {0x1 << 24, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_TWI_TWCK1    {0x1 << 25, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PINS_TWI1     PIN_TWI_TWD1, PIN_TWI_TWCK1
 
/// USART0
#define PIN_USART0_RXD    {0x1 << 19, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART0_TXD    {0x1 << 18, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART0_CTS    {0x1 << 8, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART0_RTS    {0x1 << 7, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART0_SCK    {0x1 << 17, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
 
/// USART1
#define PIN_USART1_RXD    {0x1 << 21, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART1_TXD    {0x1 << 20, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_USART1_CTS    {0x1 << 23, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
#define PIN_USART1_RTS    {0x1 << 22, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
#define PIN_USART1_SCK    {0x1 << 24, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
 
/// USB VBus monitoring pin definition.
#define PIN_USB_VBUS    {1 << 31, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_PULLUP}
 
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - External components"
/// This page lists the definitions related to external on-board components
/// located in the board.h file for the AT91SAM3UE-EK.
///
/// !AT45 Dataflash Card
/// - BOARD_AT45_A_SPI_BASE
/// - BOARD_AT45_A_SPI_ID
/// - BOARD_AT45_A_SPI_PINS
/// - BOARD_AT45_A_SPI
/// - BOARD_AT45_A_NPCS
/// - BOARD_AT45_A_NPCS_PIN
///
/// !AT45 Dataflash (serial onboard DataFlash)
/// - BOARD_AT45_B_SPI_BASE
/// - BOARD_AT45_B_SPI_ID
/// - BOARD_AT45_B_SPI_PINS
/// - BOARD_AT45_B_SPI
/// - BOARD_AT45_B_NPCS
/// - BOARD_AT45_B_NPCS_PIN
///
/// !AT26 Serial Flash
/// - BOARD_AT26_A_SPI_BASE
/// - BOARD_AT26_A_SPI_ID
/// - BOARD_AT26_A_SPI_PINS
/// - BOARD_AT26_A_SPI
/// - BOARD_AT26_A_NPCS
/// - BOARD_AT26_A_NPCS_PIN
///
/// !SD Card
/// - MCI2_INTERFACE
/// - BOARD_SD_MCI_BASE
/// - BOARD_SD_MCI_ID
/// - BOARD_SD_PINS
/// - BOARD_SD_SLOT
///
/// !PSRAM
/// - BOARD_PSRAM_PINS
/// - BOARD_LCD_PINS
 
/// Base address of SPI peripheral connected to the dataflash.
//#define BOARD_AT45_A_SPI_BASE         AT91C_BASE_SPI0
///// Identifier of SPI peripheral connected to the dataflash.
//#define BOARD_AT45_A_SPI_ID           AT91C_ID_SPI0
///// Pins of the SPI peripheral connected to the dataflash.
//#define BOARD_AT45_A_SPI_PINS         PINS_SPI0
///// Dataflahs SPI number.
//#define BOARD_AT45_A_SPI              0
///// Chip select connected to the dataflash.
//#define BOARD_AT45_A_NPCS             3
///// Chip select pin connected to the dataflash.
//#define BOARD_AT45_A_NPCS_PIN         PIN_SPI0_NPCS3
 
/// Base address of SPI peripheral connected to the dataflash.
//#define BOARD_AT45_B_SPI_BASE         AT91C_BASE_SPI1
///// Identifier of SPI peripheral connected to the dataflash.
//#define BOARD_AT45_B_SPI_ID           AT91C_ID_SPI1
///// Pins of the SPI peripheral connected to the dataflash.
//#define BOARD_AT45_B_SPI_PINS         PINS_SPI1
///// Dataflahs SPI number.
//#define BOARD_AT45_B_SPI              1
///// Chip select connected to the dataflash.
//#define BOARD_AT45_B_NPCS             3
///// Chip select pin connected to the dataflash.
//#define BOARD_AT45_B_NPCS_PIN         PIN_SPI1_NPCS3
 
/// Base address of SPI peripheral connected to the serialflash.
//#define BOARD_AT26_A_SPI_BASE         AT91C_BASE_SPI0
///// Identifier of SPI peripheral connected to the serialflash.
//#define BOARD_AT26_A_SPI_ID           AT91C_ID_SPI0
///// Pins of the SPI peripheral connected to the serialflash.
//#define BOARD_AT26_A_SPI_PINS         PINS_SPI0
///// Serialflash SPI number.
//#define BOARD_AT26_A_SPI              0
///// Chip select connected to the serialflash.
//#define BOARD_AT26_A_NPCS             3
///// Chip select pin connected to the serialflash.
//#define BOARD_AT26_A_NPCS_PIN         PIN_SPI0_NPCS3
 
/// HS MCI interface
#define MCI2_INTERFACE
/// Base address of the MCI peripheral connected to the SD card.
#define BOARD_SD_MCI_BASE           AT91C_BASE_MCI0//AT91C_BASE_MCI
///// Peripheral identifier of the MCI connected to the SD card.
#define BOARD_SD_MCI_ID             AT91C_ID_MCI0 //AT91C_ID_MCI
///// MCI pins that shall be configured to access the SD card.
#define BOARD_SD_PINS               PINS_MCI
///// MCI slot to which the SD card is connected to.
#define BOARD_SD_SLOT               MCI_SD_SLOTA
///// MCI Card Detect pin.
#define BOARD_SD_PIN_CD             PIN_MCI_CD
 
#define BOARD_PSRAM_PINS            PIN_EBI_DATA_BUS, PIN_EBI_NCS0, PIN_EBI_NRD, PIN_EBI_NWE, \
                                        PIN_EBI_PSRAM_ADDR_BUS, PIN_EBI_PSRAM_NBS, PIN_EBI_A1
 
/// Indicates board has an HX8347 external component to manage LCD.
#define BOARD_LCD_HX8347
 
/// LCD pins definition.
#define BOARD_LCD_PINS              PIN_EBI_DATA_BUS, PIN_EBI_LCD_RS, PIN_EBI_NRD, PIN_EBI_NWE, \
                                        PIN_EBI_NCS2
/// Backlight pin definition.
#define BOARD_BACKLIGHT_PIN       {1 << 19, AT91C_BASE_PIOC, AT91C_ID_PIOC, \
                                      PIO_OUTPUT_0, PIO_DEFAULT}
/// Define HX8347 base address.
#define BOARD_LCD_BASE            0x62000000
/// Define HX8347 register select signal.
#define BOARD_LCD_RS              (1 << 1)
/// Display width in pixels.
#define BOARD_LCD_WIDTH             240
/// Display height in pixels.
#define BOARD_LCD_HEIGHT            320
 
/// Indicates board has an ADS7843 external component to manage Touch Screen
#define BOARD_TSC_ADS7843
 
/// Touchscreen controller IRQ pin definition.
#define PIN_TCS_IRQ {AT91C_PIO_PA24, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_PULLUP}
/// Touchscreen controller Busy pin definition.
#define PIN_TCS_BUSY {AT91C_PIO_PA2, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_PULLUP}
 
/// Base address of SPI peripheral connected to the touchscreen controller.
#define BOARD_TSC_SPI_BASE         AT91C_BASE_SPI0
/// Identifier of SPI peripheral connected to the touchscreen controller.
#define BOARD_TSC_SPI_ID           AT91C_ID_SPI0
/// Pins of the SPI peripheral connected to the touchscreen controller.
#define BOARD_TSC_SPI_PINS         PINS_SPI0
/// Chip select connected to the touchscreen controller.
#define BOARD_TSC_NPCS             2//2
/// Chip select pin connected to the touchscreen controller.
#define BOARD_TSC_NPCS_PIN         PIN_SPI0_NPCS2_PC14
 
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - Memories"
/// This page lists definitions related to internal & external on-board memories.
///
/// !Embedded Flash
/// - BOARD_FLASH_EFC
 
/// Internal SRAM address
#define AT91C_ISRAM                   AT91C_IRAM
#define AT91C_ISRAM_SIZE         AT91C_IRAM_SIZE
 
#define AT91C_IFLASH                   (0x80000)
#define AT91C_IFLASH_SIZE              (0x20000)
#define AT91C_IFLASH_PAGE_SIZE             (256) // Internal FLASH 0 Page Size: 256 bytes
#define AT91C_IFLASH_NB_OF_PAGES           (512) // Internal FLASH 0 Number of Pages: 512
#define AT91C_IFLASH_LOCK_REGION_SIZE     (8192) // Internal FLASH 0 Lock Region Size: 8 Kbytes
#define AT91C_IFLASH_NB_OF_LOCK_BITS        (16) // Internal FLASH 0 Number of Lock Bits: 32
#if 0
#define AT91C_IFLASH1                 (0x100000)
#define AT91C_IFLASH1_SIZE             (0x20000)
#define AT91C_IFLASH1_PAGE_SIZE            (256) // Internal FLASH 1 Page Size: 256 bytes
#define AT91C_IFLASH1_NB_OF_PAGES          (512) // Internal FLASH 1 Number of Pages: 512
#define AT91C_IFLASH1_LOCK_REGION_SIZE   (8192) // Internal FLASH 1 Lock Region Size: 8 Kbytes
#define AT91C_IFLASH1_NB_OF_LOCK_BITS       (16) // Internal FLASH 1 Number of Lock Bits: 32
#endif
/// Indicates chip has an EFC.
#define AT91C_BASE_EFC    AT91C_BASE_EFC0
//------------------------------------------------------------------------------
 
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - External components"
/// This page lists the definitions related to external on-board components
/// located in the board.h file for the SAM3UE-EK.
///
/// !ISO7816
/// - PIN_SMARTCARD_CONNECT
/// - PIN_ISO7816_RSTMC
/// - PINS_ISO7816
 
/// Smartcard detection pin
//#define PIN_SMARTCARD_CONNECT   {1 << 5, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_INPUT, PIO_DEFAULT}
/// PIN used for reset the smartcard
//#define PIN_ISO7816_RSTMC       {1 << 7, AT91C_BASE_PIOA, AT91C_ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
/// Pins used for connect the smartcard
//#define PINS_ISO7816            PIN_USART0_TXD, PIN_USART0_SCK, PIN_ISO7816_RSTMC
 
/// Dma channel number
#define BOARD_MCI_DMA_CHANNEL                         0
/// MCI0 DMA hardware handshaking ID
#define DMA_HW_SRC_REQ_ID_MCI0      AT91C_HDMA_SRC_PER_0
#define DMA_HW_DEST_REQ_ID_MCI0     AT91C_HDMA_DST_PER_0
/// MCI1 DMA hardware handshaking ID
#define DMA_HW_SRC_REQ_ID_MCI1      AT91C_HDMA_SRC_PER_13
#define DMA_HW_DEST_REQ_ID_MCI1     AT91C_HDMA_DST_PER_13
/// SD DMA hardware handshaking ID
#define BOARD_SD_DMA_HW_SRC_REQ_ID      DMA_HW_SRC_REQ_ID_MCI0
#define BOARD_SD_DMA_HW_DEST_REQ_ID     DMA_HW_DEST_REQ_ID_MCI0
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM3UE-EK - Individual chip definition"
/// This page lists the definitions related to different chip's definition
/// located in the board.h file for the SAM3UE-EK.
 
/// DBGU
#define BOARD_DBGU_ID               AT91C_ID_DBGU
 
/// Rtc
#define BOARD_RTC_ID                AT91C_ID_RTC
 
/// Twi eeprom
#define BOARD_ID_TWI_EEPROM         AT91C_ID_TWI1
#define BOARD_BASE_TWI_EEPROM       AT91C_BASE_TWI1
#define BOARD_PINS_TWI_EEPROM       PINS_TWI1
 
/// USART
#define BOARD_PIN_USART_RXD        PIN_USART1_RXD
#define BOARD_PIN_USART_TXD        PIN_USART1_TXD
#define BOARD_PIN_USART_CTS        PIN_USART1_CTS
#define BOARD_PIN_USART_RTS        PIN_USART1_RTS
#define BOARD_USART_BASE           AT91C_BASE_US1
#define BOARD_ID_USART             AT91C_ID_US1
 
/// Interrupt source
typedef enum IRQn
{
/******  Cortex-M3 Processor Exceptions Numbers ***************************************************/
  NonMaskableInt_IRQn         = -14,    /*!< 2 Non Maskable Interrupt                             */
  MemoryManagement_IRQn       = -12,    /*!< 4 Cortex-M3 Memory Management Interrupt              */
  BusFault_IRQn               = -11,    /*!< 5 Cortex-M3 Bus Fault Interrupt                      */
  UsageFault_IRQn             = -10,    /*!< 6 Cortex-M3 Usage Fault Interrupt                    */
  SVCall_IRQn                 = -5,     /*!< 11 Cortex-M3 SV Call Interrupt                       */
  DebugMonitor_IRQn           = -4,     /*!< 12 Cortex-M3 Debug Monitor Interrupt                 */
  PendSV_IRQn                 = -2,     /*!< 14 Cortex-M3 Pend SV Interrupt                       */
  SysTick_IRQn                = -1,     /*!< 15 Cortex-M3 System Tick Interrupt                   */
 
/******  AT91SAM3U4 specific Interrupt Numbers *********************************************************/
 IROn_SUPC                = AT91C_ID_SUPC , // SUPPLY CONTROLLER
 IROn_RSTC                = AT91C_ID_RSTC , // RESET CONTROLLER
 IROn_RTC                 = AT91C_ID_RTC  , // REAL TIME CLOCK
 IROn_RTT                 = AT91C_ID_RTT  , // REAL TIME TIMER
 IROn_WDG                 = AT91C_ID_WDG  , // WATCHDOG TIMER
 IROn_PMC                 = AT91C_ID_PMC  , // PMC
 IROn_EFC0                = AT91C_ID_EFC0 , // EFC0
 IROn_EFC1                = AT91C_ID_EFC1 , // EFC1
 IROn_DBGU                = AT91C_ID_DBGU , // DBGU
 IROn_HSMC4               = AT91C_ID_HSMC4, // HSMC4
 IROn_PIOA                = AT91C_ID_PIOA , // Parallel IO Controller A
 IROn_PIOB                = AT91C_ID_PIOB , // Parallel IO Controller B
 IROn_PIOC                = AT91C_ID_PIOC , // Parallel IO Controller C
 IROn_US0                 = AT91C_ID_US0  , // USART 0
 IROn_US1                 = AT91C_ID_US1  , // USART 1
 IROn_US2                 = AT91C_ID_US2  , // USART 2
 IROn_US3                 = AT91C_ID_US3  , // USART 3
 IROn_MCI0                = AT91C_ID_MCI0 , // Multimedia Card Interface
 IROn_TWI0                = AT91C_ID_TWI0 , // TWI 0
 IROn_TWI1                = AT91C_ID_TWI1 , // TWI 1
 IROn_SPI0                = AT91C_ID_SPI0 , // Serial Peripheral Interface
 IROn_SSC0                = AT91C_ID_SSC0 , // Serial Synchronous Controller 0
 IROn_TC0                 = AT91C_ID_TC0  , // Timer Counter 0
 IROn_TC1                 = AT91C_ID_TC1  , // Timer Counter 1
 IROn_TC2                 = AT91C_ID_TC2  , // Timer Counter 2
 IROn_PWMC                = AT91C_ID_PWMC , // Pulse Width Modulation Controller
 IROn_ADCC0               = AT91C_ID_ADCC0, // ADC controller0
 IROn_ADCC1               = AT91C_ID_ADCC1, // ADC controller1
 IROn_HDMA                = AT91C_ID_HDMA , // HDMA
 IROn_UDPHS               = AT91C_ID_UDPHS // USB Device High Speed
} IRQn_Type;  
 
/// Dummy define SDRAM bus width 
#define BOARD_SDRAM_BUSWIDTH    32
 
//------------------------------------------------------------------------------
 
 
#define PIN_EBI_NANDOE          {1 << 17, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_NANDWE          {1 << 18, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_NANDCLE         {1 << 22, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
#define PIN_EBI_NANDALE         {1 << 21, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
 
#ifdef CHIP_NAND_CTRL
/// Nandflash chip enable pin definition.
#define BOARD_NF_CE_PIN         {1 << 12, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/// Nandflash ready/busy pin definition.
#define BOARD_NF_RB_PIN         {1 << 24, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_PERIPH_A, PIO_PULLUP}
 
/// Nandflash controller peripheral pins definition.
#define PINS_NANDFLASH          BOARD_NF_CE_PIN, BOARD_NF_RB_PIN, PIN_EBI_NANDOE, PIN_EBI_NANDWE,\
                                PIN_EBI_NANDCLE, PIN_EBI_NANDALE, PIN_EBI_DATA_BUS
 
/// Address for transferring command bytes to the nandflash.
#define BOARD_NF_COMMAND_ADDR   0x60000000
/// Address for transferring address bytes to the nandflash.
#define BOARD_NF_ADDRESS_ADDR   0x61200000
/// Address for transferring data bytes to the nandflash.
#define BOARD_NF_DATA_ADDR      0x61000000
 
#else
/// Nandflash controller peripheral pins definition.
#define PINS_NANDFLASH          BOARD_NF_CE_PIN, BOARD_NF_RB_PIN, PIN_EBI_NANDOE, PIN_EBI_NANDWE,\
                                PIN_EBI_NANDCLE, PIN_EBI_NANDALE
/// Nandflash chip enable pin definition.
#define BOARD_NF_CE_PIN         {1 << 12, AT91C_BASE_PIOC, AT91C_ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
/// Nandflash ready/busy pin definition.
#define BOARD_NF_RB_PIN         {1 << 24, AT91C_BASE_PIOB, AT91C_ID_PIOB, PIO_INPUT, PIO_PULLUP}
/// Address for transferring command bytes to the nandflash.
#define BOARD_NF_COMMAND_ADDR   0x61400000
/// Address for transferring address bytes to the nandflash.
#define BOARD_NF_ADDRESS_ADDR   0x61200000
/// Address for transferring data bytes to the nandflash.
#define BOARD_NF_DATA_ADDR      0x61000000
 
#endif
 
#endif //#ifndef BOARD_H
 
 

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.