Subversion Repositories openrisc_2011-10-31

/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support 
 * ----------------------------------------------------------------------------
 * Copyright (c) 2008, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */
 
//------------------------------------------------------------------------------
//         Headers
//------------------------------------------------------------------------------
 
#include "board.h"
#include "board_memories.h"
 
//------------------------------------------------------------------------------
//         Local definitions
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// \page "SAM9XE - Oscillator & PLL Parameters"
/// This page lists the parameters which are set for the PLL and main
/// oscillator configuration.
///
/// !Parameters
/// - BOARD_OSCOUNT
/// - BOARD_CKGR_PLLA
/// - BOARD_PLLACOUNT
/// - BOARD_MULA
/// - BOARD_DIVA
/// - BOARD_CKGR_PLLB
/// - BOARD_PLLBCOUNT
/// - BOARD_MULB
/// - BOARD_DIVB
/// - BOARD_USBDIV
/// - BOARD_PRESCALER
 
/// Main oscillator startup time (in number of slow clock ticks). 
#define BOARD_OSCOUNT           (AT91C_CKGR_OSCOUNT & (64 << 8))
 
/// PLLA frequency range.
#define BOARD_CKGR_PLLA         (AT91C_CKGR_SRCA | AT91C_CKGR_OUTA_2)
/// PLLA startup time (in number of slow clock ticks).
#define BOARD_PLLACOUNT         (63 << 8)
/// PLLA MUL value.
#define BOARD_MULA              (AT91C_CKGR_MULA & (96 << 16))
/// PLLA DIV value.
#define BOARD_DIVA              (AT91C_CKGR_DIVA & 9)
 
/// PLLB frequency range
#define BOARD_CKGR_PLLB         AT91C_CKGR_OUTB_1
/// PLLB startup time (in number of slow clock ticks).
#define BOARD_PLLBCOUNT         BOARD_PLLACOUNT
/// PLLB MUL value.
#define BOARD_MULB              (124 << 16)
/// PLLB DIV value.
#define BOARD_DIVB              12
 
/// USB PLL divisor value to obtain a 48MHz clock.
#define BOARD_USBDIV            AT91C_CKGR_USBDIV_2
/// Master clock prescaler value.
#define BOARD_PRESCALER         AT91C_PMC_MDIV_2
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
//         Local functions
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// Default spurious interrupt handler
//------------------------------------------------------------------------------
void DefaultSpuriousHandler(void)
{
    while (1);
}
 
//------------------------------------------------------------------------------
/// Default handler for fast interrupt requests.
//------------------------------------------------------------------------------
void DefaultFiqHandler(void)
{
    while (1);
}
 
//------------------------------------------------------------------------------
/// Default handler for standard interrupt requests.
//------------------------------------------------------------------------------
void DefaultIrqHandler(void)
{
    while (1);
}
 
//------------------------------------------------------------------------------
//         Global functions
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// Performs the low-level initialization of the chip.
//------------------------------------------------------------------------------
void LowLevelInit(void)
{
    unsigned char i;
 
    // Set flash wait states
    //----------------------
    AT91C_BASE_EFC->EFC_FMR = 6 << 8;
 
//#if !defined(sdram)
    // Initialize main oscillator
    //---------------------------
    AT91C_BASE_PMC->PMC_MOR = BOARD_OSCOUNT | AT91C_CKGR_MOSCEN;
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MOSCS));
 
    // Initialize PLLA at 200MHz (198.656)
    AT91C_BASE_PMC->PMC_PLLAR = BOARD_CKGR_PLLA
                                | BOARD_PLLACOUNT
                                | BOARD_MULA
                                | BOARD_DIVA;
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCKA));
 
    // Initialize PLLB for USB usage
    AT91C_BASE_PMC->PMC_PLLBR = BOARD_USBDIV
                                | BOARD_CKGR_PLLB
                                | BOARD_PLLBCOUNT
                                | BOARD_MULB
                                | BOARD_DIVB;
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCKB));
 
    // Wait for the master clock if it was already initialized
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY));
 
    // Switch to fast clock
    //---------------------
    // Switch to main oscillator + prescaler
    AT91C_BASE_PMC->PMC_MCKR = BOARD_PRESCALER;
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY));
 
    // Switch to PLL + prescaler
    AT91C_BASE_PMC->PMC_MCKR |= AT91C_PMC_CSS_PLLA_CLK;
    while (!(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY));
//#endif //#if !defined(sdram)
 
    // Initialize AIC
    //---------------
    AT91C_BASE_AIC->AIC_IDCR = 0xFFFFFFFF;
    AT91C_BASE_AIC->AIC_SVR[0] = (unsigned int) DefaultFiqHandler;
    for (i = 1; i < 31; i++) {
 
        AT91C_BASE_AIC->AIC_SVR[i] = (unsigned int) DefaultIrqHandler;
    }
    AT91C_BASE_AIC->AIC_SPU = (unsigned int) DefaultSpuriousHandler;
 
    // Unstack nested interrupts
    for (i = 0; i < 8 ; i++) {
 
        AT91C_BASE_AIC->AIC_EOICR = 0;
    }
 
    // Watchdog initialization
    //------------------------
    AT91C_BASE_WDTC->WDTC_WDMR = AT91C_WDTC_WDDIS;
 
    // Remap
    //------
    BOARD_RemapRam();
 
    // Disable RTT and PIT interrupts (potential problem when program A
    // configures RTT, then program B wants to use PIT only, interrupts
    // from the RTT will still occur since they both use AT91C_ID_SYS)
    AT91C_BASE_RTTC->RTTC_RTMR &= ~(AT91C_RTTC_ALMIEN | AT91C_RTTC_RTTINCIEN);
    AT91C_BASE_PITC->PITC_PIMR &= ~AT91C_PITC_PITIEN;
}