OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [Common/] [drivers/] [Atmel/] [at91lib/] [peripherals/] [supc/] [supc.c] - Rev 609

Go to most recent revision | Compare with Previous | Blame | View Log

/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support 
 * ----------------------------------------------------------------------------
 * Copyright (c) 2008, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */
 
//------------------------------------------------------------------------------
//         Headers
//------------------------------------------------------------------------------
 
#include "supc.h"
#include <board.h>
#include <utility/assert.h>
 
//------------------------------------------------------------------------------
//         Local definitions
//------------------------------------------------------------------------------
 
/// Key value for the SUPC_MR register.
#define SUPC_KEY            ((unsigned int) (0xA5 << 24))
 
//------------------------------------------------------------------------------
//         Global functions
//------------------------------------------------------------------------------
 
//------------------------------------------------------------------------------
/// Enables the SLCD power supply.
/// \param internal  If 1, the power supply is configured as internal; otherwise
///                  it is set at external.
//------------------------------------------------------------------------------
void SUPC_EnableSlcd(unsigned char internal)
{
    if (internal) {
 
         AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_LCDMODE) | AT91C_SUPC_LCDMODE_INTERNAL;
    }
    else {
 
        AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_LCDMODE) | AT91C_SUPC_LCDMODE_EXTERNAL;
    }
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_LCDS) != AT91C_SUPC_LCDS);
}
 
//------------------------------------------------------------------------------
/// Disables the SLCD power supply.
//------------------------------------------------------------------------------
void SUPC_DisableSlcd(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_LCDMODE);
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_LCDS) == AT91C_SUPC_LCDS);
}
 
//------------------------------------------------------------------------------
/// Sets the output voltage of the SLCD charge pump.
/// \param voltage  Output voltage.
//------------------------------------------------------------------------------
void SUPC_SetSlcdVoltage(unsigned int voltage)
{
    SANITY_CHECK((voltage & ~AT91C_SUPC_LCDOUT) == 0);
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_LCDOUT) | voltage;
}
 
#if !defined(__ICCARM__)
__attribute__ ((section (".ramfunc"))) // GCC
#endif
//------------------------------------------------------------------------------
/// Enables the flash power supply with the given wake-up setting.
/// \param time  Wake-up time.
//------------------------------------------------------------------------------
void SUPC_EnableFlash(unsigned int time)
{
    AT91C_BASE_SUPC->SUPC_FWUTR = time;
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | AT91C_BASE_SUPC->SUPC_MR | AT91C_SUPC_FLASHON;
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_FLASHS) != AT91C_SUPC_FLASHS);
}
 
#if !defined(__ICCARM__)
__attribute__ ((section (".ramfunc"))) // GCC
#endif
//------------------------------------------------------------------------------
/// Disables the flash power supply.
//------------------------------------------------------------------------------
void SUPC_DisableFlash(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_FLASHON);
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_FLASHS) == AT91C_SUPC_FLASHS);
}
 
//------------------------------------------------------------------------------
/// Sets the voltage regulator output voltage.
/// \param voltage  Voltage to set.
//------------------------------------------------------------------------------
void SUPC_SetVoltageOutput(unsigned int voltage)
{
    SANITY_CHECK((voltage & ~AT91C_SUPC_VRVDD) == 0);
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_VRVDD) | voltage;
}
 
//------------------------------------------------------------------------------
/// Puts the voltage regulator in deep mode.
//------------------------------------------------------------------------------
void SUPC_EnableDeepMode(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | AT91C_BASE_SUPC->SUPC_MR | AT91C_SUPC_VRDEEP;
}
 
//------------------------------------------------------------------------------
/// Puts the voltage regulator in normal mode.
//------------------------------------------------------------------------------
void SUPC_DisableDeepMode(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_VRDEEP);
}
 
//-----------------------------------------------------------------------------
/// Enables the backup SRAM power supply, so its data is saved while the device
/// is in backup mode.
//-----------------------------------------------------------------------------
void SUPC_EnableSram(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | AT91C_BASE_SUPC->SUPC_MR | AT91C_SUPC_SRAMON;
}
 
//-----------------------------------------------------------------------------
/// Disables the backup SRAM power supply.
//-----------------------------------------------------------------------------
void SUPC_DisableSram(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_SRAMON);
}
 
//-----------------------------------------------------------------------------
/// Enables the RTC power supply.
//-----------------------------------------------------------------------------
void SUPC_EnableRtc(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | AT91C_BASE_SUPC->SUPC_MR | AT91C_SUPC_RTCON;
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_RTS) != AT91C_SUPC_RTS);
}
 
//-----------------------------------------------------------------------------
/// Disables the RTC power supply.
//-----------------------------------------------------------------------------
void SUPC_DisableRtc(void)
{
    AT91C_BASE_SUPC->SUPC_MR = SUPC_KEY | (AT91C_BASE_SUPC->SUPC_MR & ~AT91C_SUPC_RTCON);
    while ((AT91C_BASE_SUPC->SUPC_SR & AT91C_SUPC_RTS) == AT91C_SUPC_RTS);
}
 
//-----------------------------------------------------------------------------
/// Sets the BOD sampling mode (or disables it).
/// \param mode  BOD sampling mode.
//-----------------------------------------------------------------------------
void SUPC_SetBodSampling(unsigned int mode)
{
    SANITY_CHECK((mode & ~AT91C_SUPC_BODSMPL) == 0);
    AT91C_BASE_SUPC->SUPC_BOMR &= ~AT91C_SUPC_BODSMPL;
    AT91C_BASE_SUPC->SUPC_BOMR |= mode;
}
 
//------------------------------------------------------------------------------
/// Disables the voltage regulator, which makes the device enter backup mode.
//------------------------------------------------------------------------------
void SUPC_DisableVoltageRegulator(void)
{
    AT91C_BASE_SUPC->SUPC_CR = SUPC_KEY | AT91C_SUPC_VROFF;
    while (1);
}
 
//------------------------------------------------------------------------------
/// Shuts the device down so it enters Off mode.
//------------------------------------------------------------------------------
void SUPC_Shutdown(void)
{
    AT91C_BASE_SUPC->SUPC_CR = SUPC_KEY | AT91C_SUPC_SHDW;
    while (1);
}
 
//------------------------------------------------------------------------------
/// Sets the wake-up sources when in backup mode.
/// \param sources  Wake-up sources to enable.
//------------------------------------------------------------------------------
void SUPC_SetWakeUpSources(unsigned int sources)
{
    SANITY_CHECK((sources & ~0x0000000B) == 0);
    AT91C_BASE_SUPC->SUPC_WUMR &= ~0x0000000B;
    AT91C_BASE_SUPC->SUPC_WUMR |= sources;
}
 
//------------------------------------------------------------------------------
/// Sets the wake-up inputs when in backup mode.
/// \param inputs  Wake up inputs to enable.
//------------------------------------------------------------------------------
void SUPC_SetWakeUpInputs(unsigned int inputs)
{
    SANITY_CHECK((inputs & ~0xFFFF) == 0);
    AT91C_BASE_SUPC->SUPC_WUIR &= ~0xFFFF;
    AT91C_BASE_SUPC->SUPC_WUIR |= inputs;
}
 
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.