URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [MicroBlaze/] [system.mhs] - Rev 664
Go to most recent revision | Compare with Previous | Blame | View Log
# ##############################################################################
# Created by Base System Builder Wizard for Xilinx EDK 7.1.2 Build EDK_H.12.5.1
# Sun Nov 13 16:46:19 2005
# Target Board: Xilinx Virtex 4 ML403 Evaluation Platform Rev 1
# Family: virtex4
# Device: xc4vfx12
# Package: ff668
# Speed Grade: -10
# Processor: Microblaze
# System clock frequency: 100.000000 MHz
# Debug interface: On-Chip HW Debug Module
# On Chip Memory : 64 KB
# ##############################################################################
PARAMETER VERSION = 2.1.0
PORT fpga_0_RS232_Uart_RX_pin = fpga_0_RS232_Uart_RX, DIR = INPUT
PORT fpga_0_RS232_Uart_TX_pin = fpga_0_RS232_Uart_TX, DIR = OUTPUT
PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR = INOUT, VEC = [0:3]
PORT fpga_0_LEDs_Positions_GPIO_IO_pin = fpga_0_LEDs_Positions_GPIO_IO, DIR = INOUT, VEC = [0:4]
PORT sys_clk_pin = dcm_clk_s, DIR = INPUT, SIGIS = DCMCLK
PORT sys_rst_pin = sys_rst_s, DIR = INPUT
BEGIN microblaze
PARAMETER INSTANCE = microblaze_0
PARAMETER HW_VER = 4.00.a
PARAMETER C_DEBUG_ENABLED = 1
PARAMETER C_NUMBER_OF_PC_BRK = 2
PARAMETER C_NUMBER_OF_RD_ADDR_BRK = 1
PARAMETER C_NUMBER_OF_WR_ADDR_BRK = 1
BUS_INTERFACE DLMB = dlmb
BUS_INTERFACE ILMB = ilmb
BUS_INTERFACE DOPB = mb_opb
BUS_INTERFACE IOPB = mb_opb
PORT CLK = sys_clk_s
PORT DBG_CAPTURE = DBG_CAPTURE_s
PORT DBG_CLK = DBG_CLK_s
PORT DBG_REG_EN = DBG_REG_EN_s
PORT DBG_TDI = DBG_TDI_s
PORT DBG_TDO = DBG_TDO_s
PORT DBG_UPDATE = DBG_UPDATE_s
PORT Interrupt = Interrupt
END
BEGIN opb_v20
PARAMETER INSTANCE = mb_opb
PARAMETER HW_VER = 1.10.c
PARAMETER C_EXT_RESET_HIGH = 0
PORT SYS_Rst = sys_rst_s
PORT OPB_Clk = sys_clk_s
END
BEGIN opb_mdm
PARAMETER INSTANCE = debug_module
PARAMETER HW_VER = 2.00.a
PARAMETER C_MB_DBG_PORTS = 1
PARAMETER C_USE_UART = 1
PARAMETER C_UART_WIDTH = 8
PARAMETER C_BASEADDR = 0x41400000
PARAMETER C_HIGHADDR = 0x4140ffff
BUS_INTERFACE SOPB = mb_opb
PORT OPB_Clk = sys_clk_s
PORT DBG_CAPTURE_0 = DBG_CAPTURE_s
PORT DBG_CLK_0 = DBG_CLK_s
PORT DBG_REG_EN_0 = DBG_REG_EN_s
PORT DBG_TDI_0 = DBG_TDI_s
PORT DBG_TDO_0 = DBG_TDO_s
PORT DBG_UPDATE_0 = DBG_UPDATE_s
END
BEGIN lmb_v10
PARAMETER INSTANCE = ilmb
PARAMETER HW_VER = 1.00.a
PARAMETER C_EXT_RESET_HIGH = 0
PORT SYS_Rst = sys_rst_s
PORT LMB_Clk = sys_clk_s
END
BEGIN lmb_v10
PARAMETER INSTANCE = dlmb
PARAMETER HW_VER = 1.00.a
PARAMETER C_EXT_RESET_HIGH = 0
PORT SYS_Rst = sys_rst_s
PORT LMB_Clk = sys_clk_s
END
BEGIN lmb_bram_if_cntlr
PARAMETER INSTANCE = dlmb_cntlr
PARAMETER HW_VER = 1.00.b
PARAMETER C_BASEADDR = 0x00000000
PARAMETER C_HIGHADDR = 0x0000ffff
BUS_INTERFACE SLMB = dlmb
BUS_INTERFACE BRAM_PORT = dlmb_port
END
BEGIN lmb_bram_if_cntlr
PARAMETER INSTANCE = ilmb_cntlr
PARAMETER HW_VER = 1.00.b
PARAMETER C_BASEADDR = 0x00000000
PARAMETER C_HIGHADDR = 0x0000ffff
BUS_INTERFACE SLMB = ilmb
BUS_INTERFACE BRAM_PORT = ilmb_port
END
BEGIN bram_block
PARAMETER INSTANCE = lmb_bram
PARAMETER HW_VER = 1.00.a
BUS_INTERFACE PORTA = ilmb_port
BUS_INTERFACE PORTB = dlmb_port
END
BEGIN opb_uartlite
PARAMETER INSTANCE = RS232_Uart
PARAMETER HW_VER = 1.00.b
PARAMETER C_BAUDRATE = 9600
PARAMETER C_DATA_BITS = 8
PARAMETER C_ODD_PARITY = 0
PARAMETER C_USE_PARITY = 0
PARAMETER C_CLK_FREQ = 100000000
PARAMETER C_BASEADDR = 0x40600000
PARAMETER C_HIGHADDR = 0x4060ffff
BUS_INTERFACE SOPB = mb_opb
PORT OPB_Clk = sys_clk_s
PORT Interrupt = RS232_Uart_Interrupt
PORT RX = fpga_0_RS232_Uart_RX
PORT TX = fpga_0_RS232_Uart_TX
END
BEGIN opb_gpio
PARAMETER INSTANCE = LEDs_4Bit
PARAMETER HW_VER = 3.01.b
PARAMETER C_GPIO_WIDTH = 4
PARAMETER C_IS_DUAL = 0
PARAMETER C_IS_BIDIR = 1
PARAMETER C_ALL_INPUTS = 0
PARAMETER C_BASEADDR = 0x40020000
PARAMETER C_HIGHADDR = 0x4002ffff
BUS_INTERFACE SOPB = mb_opb
PORT OPB_Clk = sys_clk_s
PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO
END
BEGIN opb_gpio
PARAMETER INSTANCE = LEDs_Positions
PARAMETER HW_VER = 3.01.b
PARAMETER C_GPIO_WIDTH = 5
PARAMETER C_IS_DUAL = 0
PARAMETER C_IS_BIDIR = 1
PARAMETER C_ALL_INPUTS = 0
PARAMETER C_BASEADDR = 0x40000000
PARAMETER C_HIGHADDR = 0x4000ffff
BUS_INTERFACE SOPB = mb_opb
PORT OPB_Clk = sys_clk_s
PORT GPIO_IO = fpga_0_LEDs_Positions_GPIO_IO
END
BEGIN opb_timer
PARAMETER INSTANCE = opb_timer_1
PARAMETER HW_VER = 1.00.b
PARAMETER C_COUNT_WIDTH = 32
PARAMETER C_ONE_TIMER_ONLY = 1
PARAMETER C_BASEADDR = 0x41c00000
PARAMETER C_HIGHADDR = 0x41c0ffff
BUS_INTERFACE SOPB = mb_opb
PORT OPB_Clk = sys_clk_s
PORT Interrupt = opb_timer_1_Interrupt
END
BEGIN opb_intc
PARAMETER INSTANCE = opb_intc_0
PARAMETER HW_VER = 1.00.c
PARAMETER C_BASEADDR = 0x41200000
PARAMETER C_HIGHADDR = 0x4120ffff
PARAMETER C_HAS_IPR = 0
BUS_INTERFACE SOPB = mb_opb
PORT Irq = Interrupt
PORT Intr = RS232_Uart_Interrupt & opb_timer_1_Interrupt
END
BEGIN dcm_module
PARAMETER INSTANCE = dcm_0
PARAMETER HW_VER = 1.00.a
PARAMETER C_CLK0_BUF = TRUE
PARAMETER C_CLKIN_PERIOD = 10.000000
PARAMETER C_CLK_FEEDBACK = 1X
PARAMETER C_EXT_RESET_HIGH = 1
PORT CLKIN = dcm_clk_s
PORT CLK0 = sys_clk_s
PORT CLKFB = sys_clk_s
PORT RST = net_gnd
PORT LOCKED = dcm_0_lock
END
Go to most recent revision | Compare with Previous | Blame | View Log