OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [OpenRISC_SIM_GCC/] [drivers/] [uart.c] - Rev 622

Compare with Previous | Blame | View Log

#include "board.h"
#include "uart.h"
#include "support.h"
 
#ifdef UART_NUM_CORES
const int UART_BASE_ADR[UART_NUM_CORES] = {UART0_BASE, UART1_BASE};
const int UART_BAUDS[UART_NUM_CORES] = {UART0_BAUD_RATE, UART1_BAUS_RATE};
#else
const int UART_BASE_ADR[1] = {UART0_BASE};
const int UART_BAUDS[1] = {UART0_BAUD_RATE};
#endif
 
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
 
#define WAIT_FOR_XMITR(core)			\
        do { \
                lsr = REG8(UART_BASE_ADR[core] + UART_LSR); \
        } while ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
 
#define WAIT_FOR_THRE(core)			\
        do { \
                lsr = REG8(UART_BASE_ADR[core] + UART_LSR); \
        } while ((lsr & UART_LSR_THRE) != UART_LSR_THRE)
 
#define CHECK_FOR_CHAR(core) (REG8(UART_BASE_ADR[core] + UART_LSR) & UART_LSR_DR)
 
#define WAIT_FOR_CHAR(core)			\
         do { \
                lsr = REG8(UART_BASE_ADR[core] + UART_LSR); \
         } while ((lsr & UART_LSR_DR) != UART_LSR_DR)
 
void uart_init(int core)
{
	int divisor;
	float float_divisor;
 
	/* Reset receiver and transmiter */
	REG8(UART_BASE_ADR[core] + UART_FCR) = UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | UART_FCR_TRIGGER_14;
 
	/* Disable all interrupts */
	REG8(UART_BASE_ADR[core] + UART_IER) = 0x00;
 
	/* Set 8 bit char, 1 stop bit, no parity */
	REG8(UART_BASE_ADR[core] + UART_LCR) = UART_LCR_WLEN8 & ~(UART_LCR_STOP | UART_LCR_PARITY);
 
	/* Set baud rate */
	float_divisor = (float) IN_CLK/(16 * UART_BAUDS[core]);
	float_divisor += 0.50f; // Ensure round up
	divisor = (int) float_divisor;
 
	REG8(UART_BASE_ADR[core] + UART_LCR) |= UART_LCR_DLAB;
	REG8(UART_BASE_ADR[core] + UART_DLL) = divisor & 0x000000ff;
	REG8(UART_BASE_ADR[core] + UART_DLM) = (divisor >> 8) & 0x000000ff;
	REG8(UART_BASE_ADR[core] + UART_LCR) &= ~(UART_LCR_DLAB);
 
	return;
}
 
void uart_putc(int core, char c)
{
	unsigned char lsr;
 
	WAIT_FOR_THRE(core);
	REG8(UART_BASE_ADR[core] + UART_TX) = c;
	if(c == '\n') {
		WAIT_FOR_THRE(core);
		REG8(UART_BASE_ADR[core] + UART_TX) = '\r';
	}
	WAIT_FOR_XMITR(core);
}
 
// Only used when we know THRE is empty, typically in interrupt
void uart_putc_noblock(int core, char c)
{
	REG8(UART_BASE_ADR[core] + UART_TX) = c;
}
 
char uart_getc(int core)
{
	unsigned char lsr;
	char c;
 
	WAIT_FOR_CHAR(core);
	c = REG8(UART_BASE_ADR[core] + UART_RX);
	return c;
}
 
char uart_getc_noblock(int core)
{
	char c;
 
	c = REG8(UART_BASE_ADR[core] + UART_RX);
	return c;
}
 
int uart_check_for_char(int core)
{
	return CHECK_FOR_CHAR(core);
}
 
void uart_rxint_enable(int core)
{
	REG8(UART_BASE_ADR[core] + UART_IER) |= UART_IER_RDI;
}
 
void uart_rxint_disable(int core)
{
	REG8(UART_BASE_ADR[core] + UART_IER) &= ~(UART_IER_RDI);
}
 
void uart_txint_enable(int core)
{
	REG8(UART_BASE_ADR[core] + UART_IER) |= UART_IER_THRI;
}
 
void uart_txint_disable(int core)
{
	REG8(UART_BASE_ADR[core] + UART_IER) &= ~(UART_IER_THRI);
}
 
char uart_get_iir(int core)
{
	return REG8(UART_BASE_ADR[core] + UART_IIR);
}
 
 
char uart_get_lsr(int core)
{
	return REG8(UART_BASE_ADR[core] + UART_LSR);
}
 
 
char uart_get_msr(int core)
{
	return REG8(UART_BASE_ADR[core] + UART_MSR);
}
 
 
void uart_print_str(char *p) 
{
	while(*p != 0) {
		uart_putc(0, *p);
		p++;
	}
}
 
void uart_print_int(int n) 
{
	int  a;
	char c;
	if (n<0) {
		uart_putc(0, '-');
		n = -n;
	}
 
	a = n/10;
	if(a) uart_print_int(a);
 
	c = '0' + (n % 10);
	uart_putc(0, c);
}
 

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.