OpenCores
URL https://opencores.org/ocsvn/openrisc_2011-10-31/openrisc_2011-10-31/trunk

Subversion Repositories openrisc_2011-10-31

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [OpenRISC_SIM_GCC/] [drivers/] [uart.c] - Rev 620

Go to most recent revision | Compare with Previous | Blame | View Log

#include "support.h"
#include "board.h"
 
#include "uart.h"
 
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
 
#define WAIT_FOR_XMITR \
        do { \
                lsr = REG8(UART_BASE + UART_LSR); \
        } while ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
 
#define WAIT_FOR_THRE \
        do { \
                lsr = REG8(UART_BASE + UART_LSR); \
        } while ((lsr & UART_LSR_THRE) != UART_LSR_THRE)
 
#define CHECK_FOR_CHAR (REG8(UART_BASE + UART_LSR) & UART_LSR_DR)
 
#define WAIT_FOR_CHAR \
         do { \
                lsr = REG8(UART_BASE + UART_LSR); \
         } while ((lsr & UART_LSR_DR) != UART_LSR_DR)
 
#define UART_TX_BUFF_LEN 32
#define UART_TX_BUFF_MASK (UART_TX_BUFF_LEN -1)
 
void uart_init(void) {
	int divisor;
 
	/* Diable interrupt */
	REG8(UART_BASE + UART_IER) = 0x0;
 
	/* Reset receiver and transmiter */
	/* Set RX interrupt for each byte */
	REG8(UART_BASE + UART_FCR) = UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | UART_FCR_TRIGGER_1;
 
	/* Enable RX interrupt */
	REG8(UART_BASE + UART_IER) = UART_IER_RDI | UART_IER_THRI;
 
	/* Set 8 bit char, 1 stop bit, no parity */
	REG8(UART_BASE + UART_LCR) = UART_LCR_WLEN8 & ~(UART_LCR_STOP | UART_LCR_PARITY);
 
	/* Set baud rate */
	divisor = IN_CLK / (16 * UART_BAUD_RATE);
	REG8(UART_BASE + UART_LCR) |= UART_LCR_DLAB;
	REG8(UART_BASE + UART_DLL) = divisor & 0x000000ff;
	REG8(UART_BASE + UART_DLM) = (divisor >> 8) & 0x000000ff;
	REG8(UART_BASE + UART_LCR) &= ~(UART_LCR_DLAB);
 
	return;
}
 
void uart_putc(char c) {
	unsigned char lsr;
 
	WAIT_FOR_THRE;
	REG8(UART_BASE + UART_TX) = c;
	if(c == '\n') {
		WAIT_FOR_THRE;
		REG8(UART_BASE + UART_TX) = '\r';
	}
	WAIT_FOR_XMITR;
}
 
 
char uart_getc(void) {
	unsigned char lsr;
	char c;
 
	WAIT_FOR_CHAR;
	c = REG8(UART_BASE + UART_RX);
	return c;
}
 
void uart_print_str(char *p) {
	while(*p != 0) {
		uart_putc(*p);
		p++;
	}
}
 
void uart_put_int(int n) {
	int  a;
	char c;
	if (n<0) {
		uart_putc('-');
		n = -n;
	}
 
	a = n/10;
	if(a) uart_put_int(a);
 
	c = '0' + (n % 10);
	uart_putc(c);
}
 
 
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.