URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [lwIP_AVR32_UC3/] [DRIVERS/] [USART/] [usart.h] - Rev 867
Go to most recent revision | Compare with Previous | Blame | View Log
/*This file is prepared for Doxygen automatic documentation generation.*/ /*! \file ********************************************************************* * * \brief USART driver for AVR32 UC3. * * This file contains basic functions for the AVR32 USART, with support for all * modes, settings and clock speeds. * * - Compiler: IAR EWAVR32 and GNU GCC for AVR32 * - Supported devices: All AVR32 devices with a USART module can be used. * - AppNote: * * \author Atmel Corporation: http://www.atmel.com \n * Support and FAQ: http://support.atmel.no/ * ******************************************************************************/ /* Copyright (c) 2007, Atmel Corporation All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * * 3. The name of ATMEL may not be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY ATMEL ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY AND * SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #ifndef _USART_H_ #define _USART_H_ #include <avr32/io.h> #include "compiler.h" /*! \name Return Values */ //! @{ #define USART_SUCCESS 0 //!< Successful completion. #define USART_FAILURE -1 //!< Failure because of some unspecified reason. #define USART_INVALID_INPUT 1 //!< Input value out of range. #define USART_INVALID_ARGUMENT -1 //!< Argument value out of range. #define USART_TX_BUSY 2 //!< Transmitter was busy. #define USART_RX_EMPTY 3 //!< Nothing was received. #define USART_RX_ERROR 4 //!< Transmission error occurred. #define USART_MODE_FAULT 5 //!< USART not in the appropriate mode. //! @} //! Default time-out value (number of attempts). #define USART_DEFAULT_TIMEOUT 10000 /*! \name Parity Settings */ //! @{ #define USART_EVEN_PARITY AVR32_USART_MR_PAR_EVEN //!< Use even parity on character transmission. #define USART_ODD_PARITY AVR32_USART_MR_PAR_ODD //!< Use odd parity on character transmission. #define USART_SPACE_PARITY AVR32_USART_MR_PAR_SPACE //!< Use a space as parity bit. #define USART_MARK_PARITY AVR32_USART_MR_PAR_MARK //!< Use a mark as parity bit. #define USART_NO_PARITY AVR32_USART_MR_PAR_NONE //!< Don't use a parity bit. #define USART_MULTIDROP_PARITY AVR32_USART_MR_PAR_MULTI //!< Parity bit is used to flag address characters. //! @} /*! \name Operating Modes */ //! @{ #define USART_MODE_NORMAL AVR32_USART_MR_MODE_NORMAL //!< Normal RS232 mode. #define USART_MODE_RS485 AVR32_USART_MR_MODE_RS485 //!< RS485 mode. #define USART_MODE_HW_HSH AVR32_USART_MR_MODE_HARDWARE //!< RS232 mode with hardware handshaking. #define USART_MODE_MODEM AVR32_USART_MR_MODE_MODEM //!< Modem mode. #define USART_MODE_ISO7816_T0 AVR32_USART_MR_MODE_ISO7816_T0 //!< ISO7816, T = 0 mode. #define USART_MODE_ISO7816_T1 AVR32_USART_MR_MODE_ISO7816_T1 //!< ISO7816, T = 1 mode. #define USART_MODE_IRDA AVR32_USART_MR_MODE_IRDA //!< IrDA mode. #define USART_MODE_SW_HSH AVR32_USART_MR_MODE_SOFTWARE //!< RS232 mode with software handshaking. //! @} /*! \name Channel Modes */ //! @{ #define USART_NORMAL_CHMODE AVR32_USART_MR_CHMODE_NORMAL //!< Normal communication. #define USART_AUTO_ECHO AVR32_USART_MR_CHMODE_ECHO //!< Echo data. #define USART_LOCAL_LOOPBACK AVR32_USART_MR_CHMODE_LOCAL_LOOP //!< Local loopback. #define USART_REMOTE_LOOPBACK AVR32_USART_MR_CHMODE_REMOTE_LOOP //!< Remote loopback. //! @} /*! \name Stop Bits Settings */ //! @{ #define USART_1_STOPBIT AVR32_USART_MR_NBSTOP_1 //!< Use 1 stop bit. #define USART_1_5_STOPBITS AVR32_USART_MR_NBSTOP_1_5 //!< Use 1.5 stop bits. #define USART_2_STOPBITS AVR32_USART_MR_NBSTOP_2 //!< Use 2 stop bits (for more, just give the number of bits). //! @} //! Input parameters when initializing RS232 and similar modes. typedef struct { //! Set baudrate of the USART. unsigned long baudrate; //! Number of bits to transmit as a character (5 to 9). unsigned char charlength; //! How to calculate the parity bit: \ref USART_EVEN_PARITY, \ref USART_ODD_PARITY, //! \ref USART_SPACE_PARITY, \ref USART_MARK_PARITY, \ref USART_NO_PARITY or //! \ref USART_MULTIDROP_PARITY. unsigned char paritytype; //! Number of stop bits between two characters: \ref USART_1_STOPBIT, //! \ref USART_1_5_STOPBITS, \ref USART_2_STOPBITS or any number from 3 to 257 //! which will result in a time guard period of that length between characters. unsigned short stopbits; //! Run the channel in testmode: \ref USART_NORMAL_CHMODE, \ref USART_AUTO_ECHO, //! \ref USART_LOCAL_LOOPBACK or \ref USART_REMOTE_LOOPBACK. unsigned char channelmode; } usart_options_t; //! Input parameters when initializing ISO7816 modes. typedef struct { //! Set the frequency of the ISO7816 clock. unsigned long iso7816_hz; //! The number of ISO7816 clock ticks in every bit period (1 to 2047, 0 = disable clock). //! Bit rate = \ref iso7816_hz / \ref fidi_ratio. unsigned short fidi_ratio; //! Inhibit Non Acknowledge:\n //! - 0: the NACK is generated;\n //! - 1: the NACK is not generated. //! //! \note This bit will be used only in ISO7816 mode, protocol T = 0 receiver. int inhibit_nack; //! Disable successive NACKs. //! Successive parity errors are counted up to the value in the \ref max_iterations field. //! These parity errors generate a NACK on the ISO line. As soon as this value is reached, //! no addititional NACK is sent on the ISO line. The ITERATION flag is asserted. int dis_suc_nack; //! Max number of repetitions (0 to 7). unsigned char max_iterations; //! Bit order in transmitted characters:\n //! - 0: LSB first;\n //! - 1: MSB first. int bit_order; } iso7816_options_t; //! Input parameters when initializing ISO7816 modes. typedef struct { //! Set the frequency of the SPI clock. unsigned long baudrate; //! Number of bits to transmit as a character (5 to 9). unsigned char charlength; //! Run the channel in testmode: \ref USART_NORMAL_CHMODE, \ref USART_AUTO_ECHO, //! \ref USART_LOCAL_LOOPBACK or \ref USART_REMOTE_LOOPBACK. unsigned char channelmode; //! Which SPI mode to use when transmitting. unsigned char spimode; } usart_spi_options_t; //------------------------------------------------------------------------------ /*! \name Initialization Functions */ //! @{ /*! \brief Resets the USART and disables TX and RX. * * \param usart Base address of the USART instance. */ extern void usart_reset(volatile avr32_usart_t *usart); /*! \brief Sets up the USART to use the standard RS232 protocol. * * \param usart Base address of the USART instance. * \param opt Options needed to set up RS232 communication (see \ref usart_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_rs232(volatile avr32_usart_t *usart, const usart_options_t *opt, long pba_hz); /*! \brief Sets up the USART to use hardware handshaking. * * \param usart Base address of the USART instance. * \param opt Options needed to set up RS232 communication (see \ref usart_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. * * \note \ref usart_init_rs232 does not need to be invoked before this function. */ extern int usart_init_hw_handshaking(volatile avr32_usart_t *usart, const usart_options_t *opt, long pba_hz); /*! \brief Sets up the USART to use the IrDA protocol. * * \param usart Base address of the USART instance. * \param opt Options needed to set up RS232 communication (see \ref usart_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * \param irda_filter Counter used to distinguish received ones from zeros. * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_IrDA(volatile avr32_usart_t *usart, const usart_options_t *opt, long pba_hz, unsigned char irda_filter); /*! \brief Sets up the USART to use the modem protocol, activating dedicated inputs/outputs. * * \param usart Base address of the USART instance. * \param opt Options needed to set up RS232 communication (see \ref usart_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_modem(volatile avr32_usart_t *usart, const usart_options_t *opt, long pba_hz); /*! \brief Sets up the USART to use the RS485 protocol. * * \param usart Base address of the USART instance. * \param opt Options needed to set up RS232 communication (see \ref usart_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_rs485(volatile avr32_usart_t *usart, const usart_options_t *opt, long pba_hz); /*! \brief Sets up the USART to use the ISO7816 T=0 or T=1 smartcard protocols. * * \param usart Base address of the USART instance. * \param opt Options needed to set up ISO7816 communication (see \ref iso7816_options_t). * \param t ISO7816 mode to use (T=0 or T=1). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_iso7816(volatile avr32_usart_t *usart, const iso7816_options_t *opt, int t, long pba_hz); /*! \brief Sets up the USART to use the SPI mode as master. * * \param usart Base address of the USART instance. * \param opt Options needed to set up SPI mode (see \ref usart_spi_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_spi_master(volatile avr32_usart_t *usart, const usart_spi_options_t *opt, long pba_hz); /*! \brief Sets up the USART to use the SPI mode as slave. * * \param usart Base address of the USART instance. * \param opt Options needed to set up SPI mode (see \ref usart_spi_options_t). * \param pba_hz USART module input clock frequency (PBA clock, Hz). * * \retval USART_SUCCESS Mode successfully initialized. * \retval USART_INVALID_INPUT One or more of the arguments is out of valid range. */ extern int usart_init_spi_slave(volatile avr32_usart_t *usart, const usart_spi_options_t *opt, long pba_hz); //! @} //------------------------------------------------------------------------------ /*! \brief Selects slave chip. * * \param usart Base address of the USART instance. * * \return Status. * \retval USART_SUCCESS Success. */ extern int usart_spi_selectChip(volatile avr32_usart_t *usart); /*! \brief Unselects slave chip. * * \param usart Base address of the USART instance. * * \return Status. * \retval USART_SUCCESS Success. * \retval USART_FAILURE Time out. */ extern int usart_spi_unselectChip(volatile avr32_usart_t *usart); //------------------------------------------------------------------------------ /*! \name Read and Reset Error Status Bits */ //! @{ /*! \brief Resets the error status. * * This function resets the status bits indicating that a parity error, * framing error or overrun has occurred. The RXBRK bit, indicating * a start/end of break condition on the RX line, is also reset. * * \param usart Base address of the USART instance. */ #if __GNUC__ __attribute__((__always_inline__)) #endif extern __inline__ void usart_reset_status(volatile avr32_usart_t *usart) { usart->cr |= AVR32_USART_CR_RSTSTA_MASK; } /*! \brief Checks if a parity error has occurred since last status reset. * * \param usart Base address of the USART instance. * * \return \c 1 if a parity error has been detected, otherwise \c 0. */ #if __GNUC__ __attribute__((__always_inline__)) #endif extern __inline__ int usart_parity_error(volatile avr32_usart_t *usart) { return (usart->csr & AVR32_USART_CSR_PARE_MASK) != 0; } /*! \brief Checks if a framing error has occurred since last status reset. * * \param usart Base address of the USART instance. * * \return \c 1 if a framing error has been detected, otherwise \c 0. */ #if __GNUC__ __attribute__((__always_inline__)) #endif extern __inline__ int usart_framing_error(volatile avr32_usart_t *usart) { return (usart->csr & AVR32_USART_CSR_FRAME_MASK) != 0; } /*! \brief Checks if an overrun error has occurred since last status reset. * * \param usart Base address of the USART instance. * * \return \c 1 if a overrun error has been detected, otherwise \c 0. */ #if __GNUC__ __attribute__((__always_inline__)) #endif extern __inline__ int usart_overrun_error(volatile avr32_usart_t *usart) { return (usart->csr & AVR32_USART_CSR_OVRE_MASK) != 0; } //! @} //------------------------------------------------------------------------------ /*! \name Transmit/Receive Functions */ //! @{ /*! \brief Addresses a receiver. * * While in RS485 mode, receivers only accept data addressed to them. * A packet/char with the address tag set has to precede any data. * This function is used to address a receiver. This receiver should read * all the following data, until an address packet addresses another receiver. * * \param usart Base address of the USART instance. * \param address Address of the target device. * * \retval USART_SUCCESS Address successfully sent (if current mode is RS485). * \retval USART_MODE_FAULT Wrong operating mode. */ extern int usart_send_address(volatile avr32_usart_t *usart, int address); /*! \brief Writes the given character to the TX buffer if the transmitter is ready. * * \param usart Base address of the USART instance. * \param c The character (up to 9 bits) to transmit. * * \retval USART_SUCCESS The transmitter was ready. * \retval USART_TX_BUSY The transmitter was busy. */ extern int usart_write_char(volatile avr32_usart_t *usart, int c); /*! \brief An active wait writing a character to the USART. * * \param usart Base address of the USART instance. * \param c The character (up to 9 bits) to transmit. */ #if __GNUC__ __attribute__((__always_inline__)) #endif extern __inline__ void usart_bw_write_char(volatile avr32_usart_t *usart, int c) { while (usart_write_char(usart, c) != USART_SUCCESS); } /*! \brief Sends a character with the USART. * * \param usart Base address of the USART instance. * \param c Character to write. * * \retval USART_SUCCESS The character was written. * \retval USART_FAILURE The function timed out before the USART transmitter became ready to send. */ extern int usart_putchar(volatile avr32_usart_t *usart, int c); /*! \brief Checks the RX buffer for a received character, and stores it at the * given memory location. * * \param usart Base address of the USART instance. * \param c Pointer to the where the read character should be stored * (must be at least short in order to accept 9-bit characters). * * \retval USART_SUCCESS The character was read successfully. * \retval USART_RX_EMPTY The RX buffer was empty. * \retval USART_RX_ERROR An error was deteceted. */ extern int usart_read_char(volatile avr32_usart_t *usart, int *c); /*! \brief Waits until a character is received, and returns it. * * \param usart Base address of the USART instance. * * \return The received character, or \ref USART_FAILURE upon error. */ extern int usart_getchar(volatile avr32_usart_t *usart); /*! \brief Writes one character string to the USART. * * \param usart Base address of the USART instance. * \param string String to be written. */ extern void usart_write_line(volatile avr32_usart_t *usart, const char *string); /*! \brief Gets and echoes characters until end of line. * * \param usart Base address of the USART instance. * * \retval USART_SUCCESS Success. * \retval USART_FAILURE ETX character received. */ extern int usart_get_echo_line(volatile avr32_usart_t *usart); //! @} #endif // _USART_H_
Go to most recent revision | Compare with Previous | Blame | View Log