URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [rtos/] [rtems/] [c/] [src/] [exec/] [score/] [cpu/] [or1k/] [cpu_asm.c] - Rev 778
Go to most recent revision | Compare with Previous | Blame | View Log
/* cpu_asm.c ===> cpu_asm.S or cpu_asm.s * * This file contains the basic algorithms for all assembly code used * in an specific CPU port of RTEMS. These algorithms must be implemented * in assembly language * * NOTE: This is supposed to be a .S or .s file NOT a C file. * * COPYRIGHT (c) 1989-1999. * On-Line Applications Research Corporation (OAR). * * The license and distribution terms for this file may be * found in the file LICENSE in this distribution or at * http://www.OARcorp.com/rtems/license.html. * * This file adapted from no_bsp board library of the RTEMS distribution. * The body has been modified for the Bender Or1k implementation by * Chris Ziomkowski. <chris@asics.ws> */ /* * This is supposed to be an assembly file. This means that system.h * and cpu.h should not be included in a "real" cpu_asm file. An * implementation in assembly should include "cpu_asm.h> */ #include <rtems/system.h> #include <rtems/score/cpu.h> /* #include "cpu_asm.h> */ /* * _CPU_Context_save_fp_context * * This routine is responsible for saving the FP context * at *fp_context_ptr. If the point to load the FP context * from is changed then the pointer is modified by this routine. * * Sometimes a macro implementation of this is in cpu.h which dereferences * the ** and a similarly named routine in this file is passed something * like a (Context_Control_fp *). The general rule on making this decision * is to avoid writing assembly language. * * or1k specific Information: * * This implementation of RTEMS considers the concept of * "fast context switching", as defined in the or1k architecture * specification. Whether or not this makes a significant * impact on speed is dubious, however it is not a significant * impediment to include it. It probably wastes a few cycles on * every floating point context switch. * * This implementation will currently not work on a processor where * the integer unit and floating point unit are not the same size. I * am waiting on an architecture change to make this feasible. It * should work fine on 64 bit architectures, except for the fact that * the variables are declared as 32 bits. This shouldn't really make * a difference, as the fact that they must be registers should force * them into a 64 bit word anyway. * * The decision as to whether to do 32 or 64 bit saves is performed * at run time based on the configuration of the CPUCFGR register. This * takes a performance hit of a few cycles, but this should be a very * small percentage of the total number of cycles necessary to do the * save, and doesn't require special code for 32 or 64 bit versions. * * ADDITIONAL INFORMATION: * * It has been unanimously agreed that floating point will not be * included in the initial releases of the Or1k chips, and that * significant changes to the floating point architecture may * occur before any such release will ever be implemented. The code * below is therefore never called and never used. */ void _CPU_Context_save_fp( void **fp_context_ptr ) { register unsigned32 temp; register unsigned32 address = (unsigned32)(*fp_context_ptr); register unsigned32 xfer; register unsigned32 loop; /* %0 is a temporary register which is used for several values throughout the code. %3 contains the address to save the context, and is modified during the course of the context save. %1 is a second dummy register which is used during transfer of the floating point value to memory. %2 is an end of loop marker which is compared against the pointer %3. */ asm volatile ("l.mfspr %0,r0,0x02 \n\t" /* CPUCFGR */ "l.andi %0,%0,0x380 \n\t" /* OF32S or OV64S or OF64S */ "l.sfnei %0,0x0 \n\t" "l.bf _L_nofps \n\t" /* exit if no floating point */ "l.sfeqi %0,0x080 \n\t" /* (DELAY) single precision? */ "l.mfspr %0,r0,0x11 \n\t" /* Load Status Register */ "l.srli %0,%0,58 \n\t" /* Move CID into low byte*32 */ "l.bnf _L_spfp_loops \n\t" /* Branch on single precision */ "l.addi %2,%0,0x20 \n" /* Terminating condition */ /**** Double Precision Floating Point Section ****/ "_L_dpfp_loops: \n\t" "l.mfspr %1,%0,0x600 \n\t" /* Load VFRx */ "l.sd 0(%3),%1 \n\t" /* Save VFRx */ "l.addi %0,%0,0x01 \n\t" /* Increment counter */ "l.sfeq %0,%2 \n\t" /* Branch if incomplete */ "l.bf _L_dpfp_loops \n\t" "l.addi %3,%3,0x08 \n\t" /* (DELAY) update pointer */ "l.bnf _L_nofps \n\t" /* exit */ "l.nop \n" /**** Single Precision Floating Point Section ****/ "_L_spfp_loops: \n\t" "l.mfspr %1,%0,0x600 \n\t" /* Load VFRx */ "l.sw 0(%3),%1 \n\t" /* Save VFRx */ "l.addi %0,%0,0x01 \n\t" /* Increment counter */ "l.sfeq %0,%2 \n\t" /* Branch if incomplete */ "l.bf _L_spfp_loops \n\t" "l.addi %3,%3,0x04 \n" /* (DELAY) update pointer */ "_L_nofps: \n\t" /* End of context save */ : "=&r" (temp), "=r" (xfer), "=&r" (loop), "+r" (address)); } /* * _CPU_Context_restore_fp_context * * This routine is responsible for restoring the FP context * at *fp_context_ptr. If the point to load the FP context * from is changed then the pointer is modified by this routine. * * */ void _CPU_Context_restore_fp( void **fp_context_ptr ) { register unsigned32 temp; register unsigned32 address = (unsigned32)(*fp_context_ptr); register unsigned32 xfer; register unsigned32 loop; /* The reverse of Context_save_fp */ /* %0 is a temporary register which is used for several values throughout the code. %1 contains the address to save the context, and is modified during the course of the context save. %2 is a second dummy register which is used during transfer of the floating point value to memory. %3 is an end of loop marker which is compared against the pointer %1. */ asm volatile ("l.mfspr %0,r0,0x02 \n\t" /* CPUCFGR */ "l.andi %0,%0,0x380 \n\t" /* OF32S or OV64S or OF64S */ "l.sfnei %0,0x0 \n\t" "l.bf _L_nofpr \n\t" /* exit if no floating point */ "l.sfeqi %0,0x080 \n\t" /* (DELAY) single precision? */ "l.mfspr %0,r0,0x11 \n\t" /* Load Status Register */ "l.srli %0,%0,58 \n\t" /* Move CID into low byte*32 */ "l.bnf _L_spfp_loopr \n\t" /* Branch on single precision */ "l.addi %3,%0,0x20 \n" /* Terminating condition */ /**** Double Precision Floating Point Section ****/ "_L_dpfp_loopr: \n\t" "l.mfspr %2,%0,0x600 \n\t" /* Load VFRx */ "l.sd 0(%1),%2 \n\t" /* Save VFRx */ "l.addi %0,%0,0x01 \n\t" /* Increment counter */ "l.sfeq %0,%3 \n\t" /* Branch if incomplete */ "l.bf _L_dpfp_loopr \n\t" "l.addi %1,%1,0x08 \n\t" /* (DELAY) update pointer */ "l.bnf _L_nofpr \n\t" /* exit */ "l.nop \n" /**** Single Precision Floating Point Section ****/ "_L_spfp_loopr: \n\t" "l.mfspr %2,%0,0x600 \n\t" /* Load VFRx */ "l.sw 0(%1),%2 \n\t" /* Save VFRx */ "l.addi %0,%0,0x01 \n\t" /* Increment counter */ "l.sfeq %0,%3 \n\t" /* Branch if incomplete */ "l.bf _L_spfp_loopr \n\t" "l.addi %1,%1,0x04 \n" /* (DELAY) update pointer */ "_L_nofpr: \n\t" /* End of context save */ : "=&r" (temp), "+r" (address), "=r" (xfer), "=&r" (loop)); } /* _CPU_Context_switch * * This routine performs a normal non-FP context switch. * * NO_CPU Specific Information: * * XXX document implementation including references if appropriate */ void _CPU_Context_switch( Context_Control *run, Context_Control *heir ) { register unsigned32 temp1 = 0; register unsigned32 temp2 = 0; /* This function is really tricky. When this function is called, we should save our state as we need it, and then grab the new state from the pointer. We then do a longjump to this code, replacing the current stack pointer with the new environment. This function never returns. Instead, at some later time, another person will call context switch with our pointer in the heir variable, and they will longjump to us. We will then continue. Let's see how this works... */ /* Technically, we could probably not worry about saving r3 and r4, since these are parameters guaranteed to be saved by the calling function. We could also probably get away without saving r11, as that is filled in by the return statement. But as a first cut I'm in favor of just saving everything.... */ /* We could be more efficient and use compile time directives for 32 or 64 bit, but this will allow the code to run on everything without modification. Feel free to comment the relevant sections out if you don't need it. */ /* We should probably write this whole routine in assembly so that we can have seperate entry points for self restore or context switch. You can't jump to local labels from inline assembly across function calls, and I don't feel like embedding all the .global directives here...it really screws up the debugger. Oh well, what's 2 more instructions and a branch really cost... */ /* One thing which we should do is check for 32 or 64 bit models first, and then do one branch to the appropriate code section. Currently, we check the architecture bit in CPUCFGR twice. Once during the load section and again during restore. That is inefficient, and considering this code is huge anyway, saving the few bytes simply doesn't make any practical sense. FIX THIS LATER. */ /* Note that this routine assumes software context switches are done with the same CID. In other words, it will not manage the CIDs and assign a new one as necessary. If you tell it to restore a context at CID 2, and the current one is at CID 4, it will do what it is told. It will overwrite the registers for context ID 2, meaning they are irretrievably lost. I hope you saved them earlier.... */ /* Note that you can have a context jump anywhere you want, although by default we will jump to the L_restore label. If you then modify the location in the Context_Control structure, it will continue whereever you told it to go. Note however that you had better also have cleaned up the stack and frame pointers though, because they are probably still set with the values obtained from entering this function... */ asm volatile ("l.sfeqi %3,0x0 \n\t" /* Is this a self restore? */ "l.bf _L_restore \n\t" /* Yes it is...go there */ "l.nop \n\t" "l.lwz %0,0(%3) \n\t" /* Prefetch new context */ "l.mfspr %2,r0,0x11 \n\t" /* Status Register */ "l.sw 0(%1),%2 \n\t" /* Save it */ "l.srli %2,%2,28 \n\t" /* Move CID into low byte */ "l.mfspr %0,%2,0x20 \n\t" /* Offset from EPCR */ "l.sw 4(%1),%0 \n\t" /* Store it */ "l.mfspr %0,%2,0x30 \n\t" /* Offset from EEAR */ "l.sw 8(%1),%0 \n\t" /* Store it */ "l.mfspr %0,%2,0x40 \n\t" /* Offset from ESR */ "l.sw 12(%1),%0 \n\t" /* Store it */ "l.mfspr %0,r0,0x02 \n\t" /* CPUCFGR */ "l.andi %0,%0,0x40 \n\t" /* OB64S */ "l.sfnei %0,0x0 \n\t" "l.bf _L_64bit \n\t" /* 64 bit architecture */ "l.movhi %0,hi(_L_restore)\n\t" /**** 32 bit implementation ****/ "l.ori %0,%0,lo(_L_restore)\n\t" "l.sw 140(%1),%0 \n\t" /* Save the PC */ "l.lwz %0,140(%3) \n\t" /* New PC. Expect cache miss */ "l.sw 16(%1),r1 \n\t" "l.sw 20(%1),r2 \n\t" "l.sw 24(%1),r3 \n\t" "l.sw 28(%1),r4 \n\t" "l.sw 32(%1),r5 \n\t" "l.sw 36(%1),r6 \n\t" "l.sw 40(%1),r7 \n\t" "l.sw 44(%1),r8 \n\t" "l.sw 48(%1),r9 \n\t" "l.sw 52(%1),r10 \n\t" "l.sw 56(%1),r11 \n\t" "l.sw 60(%1),r12 \n\t" "l.sw 64(%1),r13 \n\t" "l.sw 68(%1),r14 \n\t" "l.sw 72(%1),r15 \n\t" "l.sw 76(%1),r16 \n\t" "l.sw 80(%1),r17 \n\t" "l.sw 84(%1),r18 \n\t" "l.sw 88(%1),r19 \n\t" "l.sw 92(%1),r20 \n\t" "l.sw 96(%1),r21 \n\t" "l.sw 100(%1),r22 \n\t" "l.sw 104(%1),r23 \n\t" "l.sw 108(%1),r24 \n\t" "l.sw 112(%1),r25 \n\t" "l.sw 116(%1),r26 \n\t" "l.sw 120(%1),r27 \n\t" "l.sw 124(%1),r28 \n\t" "l.sw 128(%1),r29 \n\t" "l.sw 132(%1),r30 \n\t" "l.jr %0 \n\t" /* Go there */ "l.sw 136(%1),r31 \n" /* Store the last reg */ /**** 64 bit implementation ****/ "_L_64bit: \n\t" "l.ori %0,%0,lo(_L_restore)\n\t" "l.sw 264(%1),%0 \n\t" "l.sd 16(%1),r1 \n\t" "l.sd 24(%1),r2 \n\t" "l.sd 32(%1),r3 \n\t" "l.sd 40(%1),r4 \n\t" "l.sd 48(%1),r5 \n\t" "l.sd 56(%1),r6 \n\t" "l.sd 64(%1),r7 \n\t" "l.sd 72(%1),r8 \n\t" "l.sd 80(%1),r9 \n\t" "l.sd 88(%1),r10 \n\t" "l.sd 96(%1),r11 \n\t" "l.sd 104(%1),r12 \n\t" "l.sd 112(%1),r13 \n\t" "l.sd 120(%1),r14 \n\t" "l.sd 128(%1),r15 \n\t" "l.sd 136(%1),r16 \n\t" "l.sd 144(%1),r17 \n\t" "l.sd 152(%1),r18 \n\t" "l.sd 160(%1),r19 \n\t" "l.sd 168(%1),r20 \n\t" "l.sd 176(%1),r21 \n\t" "l.sd 184(%1),r22 \n\t" "l.sd 192(%1),r23 \n\t" "l.sd 200(%1),r24 \n\t" "l.sd 208(%1),r25 \n\t" "l.sd 216(%1),r26 \n\t" "l.sd 224(%1),r27 \n\t" "l.sd 232(%1),r28 \n\t" "l.sd 240(%1),r29 \n\t" "l.sd 248(%1),r30 \n\t" "l.jr %0 \n\t" /* Go to the new PC */ "l.sd 256(%1),r31 \n" /* Store the last reg */ /**** The restoration routine. ****/ /* Note that when we return from this function, we will actually be returning to a different context than when we left. The debugger might have conniptions over this, but we'll have to reengineer that later. The stack and status registers will all be changed, however we will not touch the global interrupt mask. */ /* Also note, when doing any restore, the most important registers are r1, r2, and r9. These will be accessed immediately upon exiting the routine, and so we want to make sure we load them as early as possible in case they are not in cache */ "_L_restore: \n\t" /* Restore "heir" */ "l.mfspr %2,r0,0x11 \n\t" /* Status Register */ "l.movhi %0,0x07FF \n\t" /* ~SR mask */ "l.ori %0,%0,0xD1FF \n\t" "l.and %2,%0,%2 \n\t" /* save the global bits */ "l.movhi %0,0xF800 \n\t" /* SR mask */ "l.ori %0,%0,0x2E00 \n\t" "l.lwz %1,0(%3) \n\t" /* Get the previous SR */ "l.and %0,%1,%0 \n\t" /* Mask out the global bits */ "l.or %2,%2,%0 \n\t" /* Combine local/global */ "l.mtspr r0,%2,0x11 \n\t" /* Restore the status register */ "l.mfspr %0,r0,0x02 \n\t" /* CPUCFGR */ "l.andi %0,%0,0x40 \n\t" /* OB64S */ "l.sfnei %0,0x0 \n\t" /* Save the 64 bit flag */ "l.srli %2,%2,28 \n\t" /* Move CID into low byte */ "l.lwz %0,4(%3) \n\t" "l.mtspr %2,%0,0x20 \n\t" /* Offset from EPCR */ "l.lwz %0,8(%3) \n\t" "l.mtspr %2,%0,0x30 \n\t" /* Offset from EEAR */ "l.lwz %0,12(%3) \n\t" "l.bf _L_r64bit \n\t" /* 64 bit architecture */ "l.mtspr %2,%0,0x30 \n\t" /* Offset from EEAR (DELAY) */ /**** 32 bit restore ****/ "l.lwz r1,16(%3) \n\t" "l.lwz r2,20(%3) \n\t" "l.lwz r9,48(%3) \n\t" "l.lwz r3,24(%3) \n\t" "l.lwz r4,28(%3) \n\t" "l.lwz r5,32(%3) \n\t" "l.lwz r6,36(%3) \n\t" "l.lwz r7,40(%3) \n\t" "l.lwz r8,44(%3) \n\t" "l.lwz r10,52(%3) \n\t" "l.lwz r11,56(%3) \n\t" "l.lwz r12,60(%3) \n\t" "l.lwz r13,64(%3) \n\t" "l.lwz r14,68(%3) \n\t" "l.lwz r15,72(%3) \n\t" "l.lwz r16,76(%3) \n\t" "l.lwz r17,80(%3) \n\t" "l.lwz r18,84(%3) \n\t" "l.lwz r19,88(%3) \n\t" "l.lwz r20,92(%3) \n\t" "l.lwz r21,96(%3) \n\t" "l.lwz r22,100(%3) \n\t" "l.lwz r23,104(%3) \n\t" "l.lwz r24,108(%3) \n\t" "l.lwz r25,112(%3) \n\t" "l.lwz r26,116(%3) \n\t" "l.lwz r27,120(%3) \n\t" "l.lwz r28,124(%3) \n\t" "l.lwz r29,128(%3) \n\t" "l.lwz r30,132(%3) \n\t" "l.j _L_return \n\t" "l.lwz r31,136(%3) \n" /**** 64 bit restore ****/ "_L_r64bit: \n\t" "l.ld r1,16(%3) \n\t" "l.ld r2,24(%3) \n\t" "l.ld r9,80(%3) \n\t" "l.ld r3,32(%3) \n\t" "l.ld r4,40(%3) \n\t" "l.ld r5,48(%3) \n\t" "l.ld r6,56(%3) \n\t" "l.ld r7,64(%3) \n\t" "l.ld r8,72(%3) \n\t" "l.ld r10,88(%3) \n\t" "l.ld r11,96(%3) \n\t" "l.ld r12,104(%3) \n\t" "l.ld r13,112(%3) \n\t" "l.ld r14,120(%3) \n\t" "l.ld r15,128(%3) \n\t" "l.ld r16,136(%3) \n\t" "l.ld r17,144(%3) \n\t" "l.ld r18,152(%3) \n\t" "l.ld r19,160(%3) \n\t" "l.ld r20,168(%3) \n\t" "l.ld r21,176(%3) \n\t" "l.ld r22,184(%3) \n\t" "l.ld r23,192(%3) \n\t" "l.ld r24,200(%3) \n\t" "l.ld r25,208(%3) \n\t" "l.ld r26,216(%3) \n\t" "l.ld r27,224(%3) \n\t" "l.ld r28,232(%3) \n\t" "l.ld r29,240(%3) \n\t" "l.ld r30,248(%3) \n\t" "l.ld r31,256(%3) \n" "_L_return: \n\t" /* End of routine */ : "=&r" (temp1), "+r" (run), "=&r" (temp2) : "r" (heir)); /* Note that some registers were used for parameter passing and temporary registeres (temp1 and temp2). These values were saved and restored across context calls, but the values that the caller needs should have been stored on the stack. The C code should now restore these from the stack, since r1 and r2 have been restored, and return to the location specified by r9. Then, all should be happy in the world. */ } /* * _CPU_Context_restore * * This routine is generally used only to restart self in an * efficient manner. It may simply be a label in _CPU_Context_switch. * * NOTE: May be unnecessary to reload some registers. * * Or1k Specific Information: * * In our implementation, this simply redirects to swich context */ void _CPU_Context_restore( Context_Control *run ) { _CPU_Context_switch(run,NULL); } /* void __ISR_Handler() * * This routine provides the RTEMS interrupt management. * * Or1k Specific Information: * * Based on the Or1k interrupt architecture described in chapter 16 * and the exception architecture described in chapter 9 */ void _ISR_Handler(unsigned32 vector,unsigned32 ProgramCounter, unsigned32 EffectiveAddress,unsigned32 StatusRegister) { /* * This discussion ignores a lot of the ugly details in a real * implementation such as saving enough registers/state to be * able to do something real. Keep in mind that the goal is * to invoke a user's ISR handler which is written in C and * uses a certain set of registers. * * Also note that the exact order is to a large extent flexible. * Hardware will dictate a sequence for a certain subset of * _ISR_Handler while requirements for setting */ /* * At entry to "common" _ISR_Handler, the vector number must be * available. On some CPUs the hardware puts either the vector * number or the offset into the vector table for this ISR in a * known place. If the hardware does not give us this information, * then the assembly portion of RTEMS for this port will contain * a set of distinct interrupt entry points which somehow place * the vector number in a known place (which is safe if another * interrupt nests this one) and branches to _ISR_Handler. * * save some or all context on stack * may need to save some special interrupt information for exit * * #if ( CPU_HAS_SOFTWARE_INTERRUPT_STACK == TRUE ) * if ( _ISR_Nest_level == 0 ) * switch to software interrupt stack * #endif * * _ISR_Nest_level++; * * _Thread_Dispatch_disable_level++; * * (*_ISR_Vector_table[ vector ])( vector ); * * --_ISR_Nest_level; * * if ( _ISR_Nest_level ) * goto the label "exit interrupt (simple case)" * * #if ( CPU_HAS_SOFTWARE_INTERRUPT_STACK == TRUE ) * restore stack * #endif * * if ( !_Context_Switch_necessary ) * goto the label "exit interrupt (simple case)" * * if ( !_ISR_Signals_to_thread_executing ) * _ISR_Signals_to_thread_executing = FALSE; * goto the label "exit interrupt (simple case)" * * call _Thread_Dispatch() or prepare to return to _ISR_Dispatch * * prepare to get out of interrupt * return from interrupt (maybe to _ISR_Dispatch) * * LABEL "exit interrupt (simple case): * prepare to get out of interrupt * return from interrupt */ /* In the Or1k architecture, exceptions are handled in the startup code of the board support package. Thus, this routine is never called. Or1k exception routines are called with the following prototype: function(int vector#, int PC, int Address, int StatusRegister); These parameters are snapshots of the system when the exception was encountered. If virtual memory is active, things like the PC and Address may have little meaning, as they are referenced in physical space, not the virtual space of the process. */ }
Go to most recent revision | Compare with Previous | Blame | View Log