URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [branches/] [oc/] [xess/] [xsv_fpga/] [README] - Rev 1767
Go to most recent revision | Compare with Previous | Blame | View Log
OpenRISC Test Application for XESS XSV800 board
===============================================
Introduction
++++++++++++
This is OpenRISC Test Application. It contains OpenRISC 1200 and a set of
OpenCores peripherals. The whole test application SoC (System-on-Chip) is
designed with the XSV board in mind. Peripherals include UART16550, VGA CRT
controller, Audio controller, debug interface, Ethernet 10/100 MAC, SRAM
and Flash controllers. CRT and Audio controller are optimized for XSV
board.
OR1200 is a 32-bit RISC with harvard architecture. For XSV800 board it is
configured with 4/4KB data/instruction caches, no D/I MMU (lack of
BlockRAMs), and with programmable interrupt controller (PIC), MAC unit,
tick timer unit and debug unit.
Software for this test application consists of:
- ORP (OpenRISC Reference Platform) monitor
- Linux (uClinux 2.0.36)
- OpenRISC GNU Toolchain (ANSI C compiler GCC, debugger etc)
Directory Structure
+++++++++++++++++++
bench: test bench (for simulation verification)
doc: Some of the documentation (more on the OpenCores web)
rtl: Verilog sources of the XSV FPGA
sim: For running simulation
sw: Software example (OR1K GNU toolchain is available from OpenCores web)
syn: Synthesis scripts/constraints for FPGA and ASIC
p&r: Download files for XSV800
Simulation
++++++++++
N/A yet.
Synthesis
+++++++++
N/A yet.
XSV800 Programming Procedure
++++++++++++++++++++++++++++
XSV800 board must be configured for 10MHz operation (see XSV documentation
how to set the clock divisor). If you want to use serial UART16550, or if
you want to use OR1K GDB debugger, you will also have to program the CPLD
with the cpld-tdm.svf file.
Make sure you set the divisor first. Download the .exo file. Then download
the .svf file. Turn the power off.
Connect XSV800 board via RS232 cable to your PC, start terminal software.
Set baud rate to 19200, data/parity/stop to 8/N/1. Now you can turn the
power back on and the FPGA will be configured from the flash and the RISC
will start booting.
What will boot depends what software is compiled and merged into the .exo
file. It can be the ORP (OpenRISC Reference Platform) monitor, or Linux,
or something else.
If you have problems downloading the files to the XSV board, please make sure
you first read the XSV manual and check the XESS website and XESS forum.
Want to help?
+++++++++++++
We need companies, universities and individuals to help us in HW and SW areas.
If you want to help, first go to http://www.opencores.org/cores/or1k-new/ and
check the status and TODOs. Also read the documentation.
Subscribe to the openrisc mailing list (and read OpenCores FAQ before you post):
- if you want more information
- if you want to help with the HW design (test application(s), verification of the
OR1200, optimization of OR1200, development of new units etc)
- if you want to develop software
If you want to help in some other area, please subscribe to main opencores
mailing list.
About OpenCores
===============
OpenCores is an organization that developes free, open source soft cores. If
you would like more information, please visit us at http://www.opencores.org.
We invite companies and individuals to help us in our mission. We need
experienced designers to verify and design new cores.
And we need companies and universities to use our existing verified cores in
projects (the whole purpose of OpenCores is to design free cores that someone
will use !).
--
Damjan Lampret, Mar/2002
$Log: not supported by cvs2svn $
Go to most recent revision | Compare with Previous | Blame | View Log