URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [tags/] [before_ORP/] [uclinux/] [uClinux-2.0.x/] [drivers/] [block/] [paride/] [friq.c] - Rev 1765
Compare with Previous | Blame | View Log
/* friq.c (c) 1998 Grant R. Guenther <grant@torque.net> Under the terms of the GNU public license friq.c is a low-level protocol driver for the Freecom "IQ" parallel port IDE adapter. Early versions of this adapter use the 'frpw' protocol. Freecom uses this adapter in a battery powered external CD-ROM drive. It is also used in LS-120 drives by Maxell and Panasonic, and other devices. The battery powered drive requires software support to control the power to the drive. This module enables the drive power when the high level driver (pcd) is loaded and disables it when the module is unloaded. Note, if the friq module is built in to the kernel, the power will never be switched off, so other means should be used to conserve battery power. */ /* Changes: 1.01 GRG 1998.12.20 Added support for soft power switch */ #define FRIQ_VERSION "1.01" #include <linux/module.h> #include <linux/delay.h> #include <linux/kernel.h> #include <linux/types.h> #include <asm/io.h> #include "paride.h" #define CMD(x) w2(4);w0(0xff);w0(0xff);w0(0x73);w0(0x73);\ w0(0xc9);w0(0xc9);w0(0x26);w0(0x26);w0(x);w0(x); #define j44(l,h) (((l>>4)&0x0f)|(h&0xf0)) /* cont = 0 - access the IDE register file cont = 1 - access the IDE command set */ static int cont_map[2] = { 0x08, 0x10 }; static int friq_read_regr( PIA *pi, int cont, int regr ) { int h,l,r; r = regr + cont_map[cont]; CMD(r); w2(6); l = r1(); w2(4); h = r1(); w2(4); return j44(l,h); } static void friq_write_regr( PIA *pi, int cont, int regr, int val) { int r; r = regr + cont_map[cont]; CMD(r); w0(val); w2(5);w2(7);w2(5);w2(4); } static void friq_read_block_int( PIA *pi, char * buf, int count, int regr ) { int h, l, k, ph; switch(pi->mode) { case 0: CMD(regr); for (k=0;k<count;k++) { w2(6); l = r1(); w2(4); h = r1(); buf[k] = j44(l,h); } w2(4); break; case 1: ph = 2; CMD(regr+0xc0); w0(0xff); for (k=0;k<count;k++) { w2(0xa4 + ph); buf[k] = r0(); ph = 2 - ph; } w2(0xac); w2(0xa4); w2(4); break; case 2: CMD(regr+0x80); for (k=0;k<count-2;k++) buf[k] = r4(); w2(0xac); w2(0xa4); buf[count-2] = r4(); buf[count-1] = r4(); w2(4); break; case 3: CMD(regr+0x80); for (k=0;k<(count/2)-1;k++) ((u16 *)buf)[k] = r4w(); w2(0xac); w2(0xa4); buf[count-2] = r4(); buf[count-1] = r4(); w2(4); break; case 4: CMD(regr+0x80); for (k=0;k<(count/4)-1;k++) ((u32 *)buf)[k] = r4l(); buf[count-4] = r4(); buf[count-3] = r4(); w2(0xac); w2(0xa4); buf[count-2] = r4(); buf[count-1] = r4(); w2(4); break; } } static void friq_read_block( PIA *pi, char * buf, int count) { friq_read_block_int(pi,buf,count,0x08); } static void friq_write_block( PIA *pi, char * buf, int count ) { int k; switch(pi->mode) { case 0: case 1: CMD(8); w2(5); for (k=0;k<count;k++) { w0(buf[k]); w2(7);w2(5); } w2(4); break; case 2: CMD(0xc8); w2(5); for (k=0;k<count;k++) w4(buf[k]); w2(4); break; case 3: CMD(0xc8); w2(5); for (k=0;k<count/2;k++) w4w(((u16 *)buf)[k]); w2(4); break; case 4: CMD(0xc8); w2(5); for (k=0;k<count/4;k++) w4l(((u32 *)buf)[k]); w2(4); break; } } static void friq_connect ( PIA *pi ) { pi->saved_r0 = r0(); pi->saved_r2 = r2(); w2(4); } static void friq_disconnect ( PIA *pi ) { CMD(0x20); w0(pi->saved_r0); w2(pi->saved_r2); } static int friq_test_proto( PIA *pi, char * scratch, int verbose ) { int j, k, r; int e[2] = {0,0}; pi->saved_r0 = r0(); w0(0xff); udelay(20); CMD(0x3d); /* turn the power on */ udelay(500); w0(pi->saved_r0); friq_connect(pi); for (j=0;j<2;j++) { friq_write_regr(pi,0,6,0xa0+j*0x10); for (k=0;k<256;k++) { friq_write_regr(pi,0,2,k^0xaa); friq_write_regr(pi,0,3,k^0x55); if (friq_read_regr(pi,0,2) != (k^0xaa)) e[j]++; } } friq_disconnect(pi); friq_connect(pi); friq_read_block_int(pi,scratch,512,0x10); r = 0; for (k=0;k<128;k++) if (scratch[k] != k) r++; friq_disconnect(pi); if (verbose) { printk("%s: friq: port 0x%x, mode %d, test=(%d,%d,%d)\n", pi->device,pi->port,pi->mode,e[0],e[1],r); } return (r || (e[0] && e[1])); } static void friq_log_adapter( PIA *pi, char * scratch, int verbose ) { char *mode_string[6] = {"4-bit","8-bit", "EPP-8","EPP-16","EPP-32"}; printk("%s: friq %s, Freecom IQ ASIC-2 adapter at 0x%x, ", pi->device, FRIQ_VERSION,pi->port); printk("mode %d (%s), delay %d\n",pi->mode, mode_string[pi->mode],pi->delay); pi->private = 1; friq_connect(pi); CMD(0x9e); /* disable sleep timer */ friq_disconnect(pi); } static void friq_init_proto( PIA *pi) { MOD_INC_USE_COUNT; pi->private = 0; } static void friq_release_proto( PIA *pi) { if (pi->private) { /* turn off the power */ friq_connect(pi); CMD(0x1d); CMD(0x1e); friq_disconnect(pi); pi->private = 0; } MOD_DEC_USE_COUNT; } struct pi_protocol friq = {"friq",0,5,2,1,1, friq_write_regr, friq_read_regr, friq_write_block, friq_read_block, friq_connect, friq_disconnect, 0, 0, friq_test_proto, friq_log_adapter, friq_init_proto, friq_release_proto }; #ifdef MODULE int init_module(void) { return pi_register( &friq ) - 1; } void cleanup_module(void) { pi_unregister( &friq ); } #endif /* end of friq.c */