URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [gdb-5.3/] [gdb/] [config/] [i386/] [nm-i386.h] - Rev 1765
Compare with Previous | Blame | View Log
/* Native macro definitions for GDB on an Intel i[3456]86. Copyright 2001 Free Software Foundation, Inc. This file is part of GDB. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ #ifndef NM_I386_H #define NM_I386_H 1 /* Hardware-assisted breakpoints and watchpoints. */ /* Targets should define this to use the generic x86 watchpoint support. */ #ifdef I386_USE_GENERIC_WATCHPOINTS #ifndef TARGET_HAS_HARDWARE_WATCHPOINTS #define TARGET_HAS_HARDWARE_WATCHPOINTS #endif /* Clear the reference counts and forget everything we knew about DRi. */ extern void i386_cleanup_dregs (void); /* Insert a watchpoint to watch a memory region which starts at address ADDR and whose length is LEN bytes. Watch memory accesses of the type TYPE. Return 0 on success, -1 on failure. */ extern int i386_insert_watchpoint (CORE_ADDR addr, int len, int type); /* Remove a watchpoint that watched the memory region which starts at address ADDR, whose length is LEN bytes, and for accesses of the type TYPE. Return 0 on success, -1 on failure. */ extern int i386_remove_watchpoint (CORE_ADDR addr, int len, int type); /* Return non-zero if we can watch a memory region that starts at address ADDR and whose length is LEN bytes. */ extern int i386_region_ok_for_watchpoint (CORE_ADDR addr, int len); /* Return non-zero if the inferior has some break/watchpoint that triggered. */ extern int i386_stopped_by_hwbp (void); /* If the inferior has some break/watchpoint that triggered, return the address associated with that break/watchpoint. Otherwise, return zero. */ extern CORE_ADDR i386_stopped_data_address (void); /* Insert a hardware-assisted breakpoint at address ADDR. SHADOW is unused. Return 0 on success, EBUSY on failure. */ extern int i386_insert_hw_breakpoint (CORE_ADDR addr, void *shadow); /* Remove a hardware-assisted breakpoint at address ADDR. SHADOW is unused. Return 0 on success, -1 on failure. */ extern int i386_remove_hw_breakpoint (CORE_ADDR addr, void *shadow); /* Returns the number of hardware watchpoints of type TYPE that we can set. Value is positive if we can set CNT watchpoints, zero if setting watchpoints of type TYPE is not supported, and negative if CNT is more than the maximum number of watchpoints of type TYPE that we can support. TYPE is one of bp_hardware_watchpoint, bp_read_watchpoint, bp_write_watchpoint, or bp_hardware_breakpoint. CNT is the number of such watchpoints used so far (including this one). OTHERTYPE is non-zero if other types of watchpoints are currently enabled. We always return 1 here because we don't have enough information about possible overlap of addresses that they want to watch. As an extreme example, consider the case where all the watchpoints watch the same address and the same region length: then we can handle a virtually unlimited number of watchpoints, due to debug register sharing implemented via reference counts in i386-nat.c. */ #define TARGET_CAN_USE_HARDWARE_WATCHPOINT(type, cnt, ot) 1 /* Returns non-zero if we can use hardware watchpoints to watch a region whose address is ADDR and whose length is LEN. */ #define TARGET_REGION_OK_FOR_HW_WATCHPOINT(addr, len) \ i386_region_ok_for_watchpoint (addr, len) /* After a watchpoint trap, the PC points to the instruction after the one that caused the trap. Therefore we don't need to step over it. But we do need to reset the status register to avoid another trap. */ #define HAVE_CONTINUABLE_WATCHPOINT #define STOPPED_BY_WATCHPOINT(W) (i386_stopped_data_address () != 0) #define target_stopped_data_address() i386_stopped_data_address () /* Use these macros for watchpoint insertion/removal. */ #define target_insert_watchpoint(addr, len, type) \ i386_insert_watchpoint (addr, len, type) #define target_remove_watchpoint(addr, len, type) \ i386_remove_watchpoint (addr, len, type) #define target_insert_hw_breakpoint(addr, shadow) \ i386_insert_hw_breakpoint (addr, shadow) #define target_remove_hw_breakpoint(addr, shadow) \ i386_remove_hw_breakpoint (addr, shadow) #define DECR_PC_AFTER_HW_BREAK 0 /* child_post_startup_inferior used to reset all debug registers by calling i386_cleanup_dregs (). */ #define CHILD_POST_STARTUP_INFERIOR #endif /* I386_USE_GENERIC_WATCHPOINTS */ #endif /* NM_I386_H */