URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [insight/] [gdb/] [doc/] [gdb.info-5] - Rev 1774
Go to most recent revision | Compare with Previous | Blame | View Log
This is ./gdb.info, produced by makeinfo version 4.0 from gdb.texinfo.
INFO-DIR-SECTION Programming & development tools.
START-INFO-DIR-ENTRY
* Gdb: (gdb). The GNU debugger.
END-INFO-DIR-ENTRY
This file documents the GNU debugger GDB.
This is the Ninth Edition, April 2001, of `Debugging with GDB: the
GNU Source-Level Debugger' for GDB Version 20010707.
Copyright (C)
1988,1989,1990,1991,1992,1993,1994,1995,1996,1998,1999,2000,2001
Free Software Foundation, Inc.
Permission is granted to copy, distribute and/or modify this document
under the terms of the GNU Free Documentation License, Version 1.1 or
any later version published by the Free Software Foundation; with the
Invariant Sections being "A Sample GDB Session" and "Free Software",
with the Front-Cover texts being "A GNU Manual," and with the
Back-Cover Texts as in (a) below.
(a) The FSF's Back-Cover Text is: "You have freedom to copy and
modify this GNU Manual, like GNU software. Copies published by the Free
Software Foundation raise funds for GNU development."
File: gdb.info, Node: Tracepoint Actions, Next: Listing Tracepoints, Prev: Tracepoint Passcounts, Up: Set Tracepoints
Tracepoint Action Lists
-----------------------
`actions [NUM]'
This command will prompt for a list of actions to be taken when the
tracepoint is hit. If the tracepoint number NUM is not specified,
this command sets the actions for the one that was most recently
defined (so that you can define a tracepoint and then say
`actions' without bothering about its number). You specify the
actions themselves on the following lines, one action at a time,
and terminate the actions list with a line containing just `end'.
So far, the only defined actions are `collect' and
`while-stepping'.
To remove all actions from a tracepoint, type `actions NUM' and
follow it immediately with `end'.
(gdb) collect DATA // collect some data
(gdb) while-stepping 5 // single-step 5 times and collect data
(gdb) end // signals the end of actions.
In the following example, the action list begins with `collect'
commands indicating the things to be collected when the tracepoint
is hit. Then, in order to single-step and collect additional data
following the tracepoint, a `while-stepping' command is used,
followed by the list of things to be collected while stepping. The
`while-stepping' command is terminated by its own separate `end'
command. Lastly, the action list is terminated by an `end'
command.
(gdb) trace foo
(gdb) actions
Enter actions for tracepoint 1, one per line:
> collect bar,baz
> collect $regs
> while-stepping 12
> collect $fp, $sp
> end
end
`collect EXPR1, EXPR2, ...'
Collect values of the given expressions when the tracepoint is hit.
This command accepts a comma-separated list of any valid
expressions. In addition to global, static, or local variables,
the following special arguments are supported:
`$regs'
collect all registers
`$args'
collect all function arguments
`$locals'
collect all local variables.
You can give several consecutive `collect' commands, each one with
a single argument, or one `collect' command with several arguments
separated by commas: the effect is the same.
The command `info scope' (*note info scope: Symbols.) is
particularly useful for figuring out what data to collect.
`while-stepping N'
Perform N single-step traces after the tracepoint, collecting new
data at each step. The `while-stepping' command is followed by
the list of what to collect while stepping (followed by its own
`end' command):
> while-stepping 12
> collect $regs, myglobal
> end
>
You may abbreviate `while-stepping' as `ws' or `stepping'.
File: gdb.info, Node: Listing Tracepoints, Next: Starting and Stopping Trace Experiment, Prev: Tracepoint Actions, Up: Set Tracepoints
Listing Tracepoints
-------------------
`info tracepoints [NUM]'
Display information the tracepoint NUM. If you don't specify a
tracepoint number displays information about all the tracepoints
defined so far. For each tracepoint, the following information is
shown:
* its number
* whether it is enabled or disabled
* its address
* its passcount as given by the `passcount N' command
* its step count as given by the `while-stepping N' command
* where in the source files is the tracepoint set
* its action list as given by the `actions' command
(gdb) info trace
Num Enb Address PassC StepC What
1 y 0x002117c4 0 0 <gdb_asm>
2 y 0x0020dc64 0 0 in gdb_test at gdb_test.c:375
3 y 0x0020b1f4 0 0 in collect_data at ../foo.c:1741
(gdb)
This command can be abbreviated `info tp'.
File: gdb.info, Node: Starting and Stopping Trace Experiment, Prev: Listing Tracepoints, Up: Set Tracepoints
Starting and Stopping Trace Experiment
--------------------------------------
`tstart'
This command takes no arguments. It starts the trace experiment,
and begins collecting data. This has the side effect of
discarding all the data collected in the trace buffer during the
previous trace experiment.
`tstop'
This command takes no arguments. It ends the trace experiment, and
stops collecting data.
*Note:* a trace experiment and data collection may stop
automatically if any tracepoint's passcount is reached (*note
Tracepoint Passcounts::), or if the trace buffer becomes full.
`tstatus'
This command displays the status of the current trace data
collection.
Here is an example of the commands we described so far:
(gdb) trace gdb_c_test
(gdb) actions
Enter actions for tracepoint #1, one per line.
> collect $regs,$locals,$args
> while-stepping 11
> collect $regs
> end
> end
(gdb) tstart
[time passes ...]
(gdb) tstop
File: gdb.info, Node: Analyze Collected Data, Next: Tracepoint Variables, Prev: Set Tracepoints, Up: Tracepoints
Using the collected data
========================
After the tracepoint experiment ends, you use GDB commands for
examining the trace data. The basic idea is that each tracepoint
collects a trace "snapshot" every time it is hit and another snapshot
every time it single-steps. All these snapshots are consecutively
numbered from zero and go into a buffer, and you can examine them
later. The way you examine them is to "focus" on a specific trace
snapshot. When the remote stub is focused on a trace snapshot, it will
respond to all GDB requests for memory and registers by reading from
the buffer which belongs to that snapshot, rather than from _real_
memory or registers of the program being debugged. This means that
*all* GDB commands (`print', `info registers', `backtrace', etc.) will
behave as if we were currently debugging the program state as it was
when the tracepoint occurred. Any requests for data that are not in
the buffer will fail.
* Menu:
* tfind:: How to select a trace snapshot
* tdump:: How to display all data for a snapshot
* save-tracepoints:: How to save tracepoints for a future run
File: gdb.info, Node: tfind, Next: tdump, Up: Analyze Collected Data
`tfind N'
---------
The basic command for selecting a trace snapshot from the buffer is
`tfind N', which finds trace snapshot number N, counting from zero. If
no argument N is given, the next snapshot is selected.
Here are the various forms of using the `tfind' command.
`tfind start'
Find the first snapshot in the buffer. This is a synonym for
`tfind 0' (since 0 is the number of the first snapshot).
`tfind none'
Stop debugging trace snapshots, resume _live_ debugging.
`tfind end'
Same as `tfind none'.
`tfind'
No argument means find the next trace snapshot.
`tfind -'
Find the previous trace snapshot before the current one. This
permits retracing earlier steps.
`tfind tracepoint NUM'
Find the next snapshot associated with tracepoint NUM. Search
proceeds forward from the last examined trace snapshot. If no
argument NUM is given, it means find the next snapshot collected
for the same tracepoint as the current snapshot.
`tfind pc ADDR'
Find the next snapshot associated with the value ADDR of the
program counter. Search proceeds forward from the last examined
trace snapshot. If no argument ADDR is given, it means find the
next snapshot with the same value of PC as the current snapshot.
`tfind outside ADDR1, ADDR2'
Find the next snapshot whose PC is outside the given range of
addresses.
`tfind range ADDR1, ADDR2'
Find the next snapshot whose PC is between ADDR1 and ADDR2.
`tfind line [FILE:]N'
Find the next snapshot associated with the source line N. If the
optional argument FILE is given, refer to line N in that source
file. Search proceeds forward from the last examined trace
snapshot. If no argument N is given, it means find the next line
other than the one currently being examined; thus saying `tfind
line' repeatedly can appear to have the same effect as stepping
from line to line in a _live_ debugging session.
The default arguments for the `tfind' commands are specifically
designed to make it easy to scan through the trace buffer. For
instance, `tfind' with no argument selects the next trace snapshot, and
`tfind -' with no argument selects the previous trace snapshot. So, by
giving one `tfind' command, and then simply hitting <RET> repeatedly
you can examine all the trace snapshots in order. Or, by saying `tfind
-' and then hitting <RET> repeatedly you can examine the snapshots in
reverse order. The `tfind line' command with no argument selects the
snapshot for the next source line executed. The `tfind pc' command with
no argument selects the next snapshot with the same program counter
(PC) as the current frame. The `tfind tracepoint' command with no
argument selects the next trace snapshot collected by the same
tracepoint as the current one.
In addition to letting you scan through the trace buffer manually,
these commands make it easy to construct GDB scripts that scan through
the trace buffer and print out whatever collected data you are
interested in. Thus, if we want to examine the PC, FP, and SP
registers from each trace frame in the buffer, we can say this:
(gdb) tfind start
(gdb) while ($trace_frame != -1)
> printf "Frame %d, PC = %08X, SP = %08X, FP = %08X\n", \
$trace_frame, $pc, $sp, $fp
> tfind
> end
Frame 0, PC = 0020DC64, SP = 0030BF3C, FP = 0030BF44
Frame 1, PC = 0020DC6C, SP = 0030BF38, FP = 0030BF44
Frame 2, PC = 0020DC70, SP = 0030BF34, FP = 0030BF44
Frame 3, PC = 0020DC74, SP = 0030BF30, FP = 0030BF44
Frame 4, PC = 0020DC78, SP = 0030BF2C, FP = 0030BF44
Frame 5, PC = 0020DC7C, SP = 0030BF28, FP = 0030BF44
Frame 6, PC = 0020DC80, SP = 0030BF24, FP = 0030BF44
Frame 7, PC = 0020DC84, SP = 0030BF20, FP = 0030BF44
Frame 8, PC = 0020DC88, SP = 0030BF1C, FP = 0030BF44
Frame 9, PC = 0020DC8E, SP = 0030BF18, FP = 0030BF44
Frame 10, PC = 00203F6C, SP = 0030BE3C, FP = 0030BF14
Or, if we want to examine the variable `X' at each source line in
the buffer:
(gdb) tfind start
(gdb) while ($trace_frame != -1)
> printf "Frame %d, X == %d\n", $trace_frame, X
> tfind line
> end
Frame 0, X = 1
Frame 7, X = 2
Frame 13, X = 255
File: gdb.info, Node: tdump, Next: save-tracepoints, Prev: tfind, Up: Analyze Collected Data
`tdump'
-------
This command takes no arguments. It prints all the data collected at
the current trace snapshot.
(gdb) trace 444
(gdb) actions
Enter actions for tracepoint #2, one per line:
> collect $regs, $locals, $args, gdb_long_test
> end
(gdb) tstart
(gdb) tfind line 444
#0 gdb_test (p1=0x11, p2=0x22, p3=0x33, p4=0x44, p5=0x55, p6=0x66)
at gdb_test.c:444
444 printp( "%s: arguments = 0x%X 0x%X 0x%X 0x%X 0x%X 0x%X\n", )
(gdb) tdump
Data collected at tracepoint 2, trace frame 1:
d0 0xc4aa0085 -995491707
d1 0x18 24
d2 0x80 128
d3 0x33 51
d4 0x71aea3d 119204413
d5 0x22 34
d6 0xe0 224
d7 0x380035 3670069
a0 0x19e24a 1696330
a1 0x3000668 50333288
a2 0x100 256
a3 0x322000 3284992
a4 0x3000698 50333336
a5 0x1ad3cc 1758156
fp 0x30bf3c 0x30bf3c
sp 0x30bf34 0x30bf34
ps 0x0 0
pc 0x20b2c8 0x20b2c8
fpcontrol 0x0 0
fpstatus 0x0 0
fpiaddr 0x0 0
p = 0x20e5b4 "gdb-test"
p1 = (void *) 0x11
p2 = (void *) 0x22
p3 = (void *) 0x33
p4 = (void *) 0x44
p5 = (void *) 0x55
p6 = (void *) 0x66
gdb_long_test = 17 '\021'
(gdb)
File: gdb.info, Node: save-tracepoints, Prev: tdump, Up: Analyze Collected Data
`save-tracepoints FILENAME'
---------------------------
This command saves all current tracepoint definitions together with
their actions and passcounts, into a file `FILENAME' suitable for use
in a later debugging session. To read the saved tracepoint
definitions, use the `source' command (*note Command Files::).
File: gdb.info, Node: Tracepoint Variables, Prev: Analyze Collected Data, Up: Tracepoints
Convenience Variables for Tracepoints
=====================================
`(int) $trace_frame'
The current trace snapshot (a.k.a. "frame") number, or -1 if no
snapshot is selected.
`(int) $tracepoint'
The tracepoint for the current trace snapshot.
`(int) $trace_line'
The line number for the current trace snapshot.
`(char []) $trace_file'
The source file for the current trace snapshot.
`(char []) $trace_func'
The name of the function containing `$tracepoint'.
Note: `$trace_file' is not suitable for use in `printf', use
`output' instead.
Here's a simple example of using these convenience variables for
stepping through all the trace snapshots and printing some of their
data.
(gdb) tfind start
(gdb) while $trace_frame != -1
> output $trace_file
> printf ", line %d (tracepoint #%d)\n", $trace_line, $tracepoint
> tfind
> end
File: gdb.info, Node: Languages, Next: Symbols, Prev: Tracepoints, Up: Top
Using GDB with Different Languages
**********************************
Although programming languages generally have common aspects, they
are rarely expressed in the same manner. For instance, in ANSI C,
dereferencing a pointer `p' is accomplished by `*p', but in Modula-2,
it is accomplished by `p^'. Values can also be represented (and
displayed) differently. Hex numbers in C appear as `0x1ae', while in
Modula-2 they appear as `1AEH'.
Language-specific information is built into GDB for some languages,
allowing you to express operations like the above in your program's
native language, and allowing GDB to output values in a manner
consistent with the syntax of your program's native language. The
language you use to build expressions is called the "working language".
* Menu:
* Setting:: Switching between source languages
* Show:: Displaying the language
* Checks:: Type and range checks
* Support:: Supported languages
File: gdb.info, Node: Setting, Next: Show, Up: Languages
Switching between source languages
==================================
There are two ways to control the working language--either have GDB
set it automatically, or select it manually yourself. You can use the
`set language' command for either purpose. On startup, GDB defaults to
setting the language automatically. The working language is used to
determine how expressions you type are interpreted, how values are
printed, etc.
In addition to the working language, every source file that GDB
knows about has its own working language. For some object file
formats, the compiler might indicate which language a particular source
file is in. However, most of the time GDB infers the language from the
name of the file. The language of a source file controls whether C++
names are demangled--this way `backtrace' can show each frame
appropriately for its own language. There is no way to set the
language of a source file from within GDB, but you can set the language
associated with a filename extension. *Note Displaying the language:
Show.
This is most commonly a problem when you use a program, such as
`cfront' or `f2c', that generates C but is written in another language.
In that case, make the program use `#line' directives in its C output;
that way GDB will know the correct language of the source code of the
original program, and will display that source code, not the generated
C code.
* Menu:
* Filenames:: Filename extensions and languages.
* Manually:: Setting the working language manually
* Automatically:: Having GDB infer the source language
File: gdb.info, Node: Filenames, Next: Manually, Up: Setting
List of filename extensions and languages
-----------------------------------------
If a source file name ends in one of the following extensions, then
GDB infers that its language is the one indicated.
`.c'
C source file
`.C'
`.cc'
`.cp'
`.cpp'
`.cxx'
`.c++'
C++ source file
`.f'
`.F'
Fortran source file
`.ch'
`.c186'
`.c286'
CHILL source file
`.mod'
Modula-2 source file
`.s'
`.S'
Assembler source file. This actually behaves almost like C, but
GDB does not skip over function prologues when stepping.
In addition, you may set the language associated with a filename
extension. *Note Displaying the language: Show.
File: gdb.info, Node: Manually, Next: Automatically, Prev: Filenames, Up: Setting
Setting the working language
----------------------------
If you allow GDB to set the language automatically, expressions are
interpreted the same way in your debugging session and your program.
If you wish, you may set the language manually. To do this, issue
the command `set language LANG', where LANG is the name of a language,
such as `c' or `modula-2'. For a list of the supported languages, type
`set language'.
Setting the language manually prevents GDB from updating the working
language automatically. This can lead to confusion if you try to debug
a program when the working language is not the same as the source
language, when an expression is acceptable to both languages--but means
different things. For instance, if the current source file were
written in C, and GDB was parsing Modula-2, a command such as:
print a = b + c
might not have the effect you intended. In C, this means to add `b'
and `c' and place the result in `a'. The result printed would be the
value of `a'. In Modula-2, this means to compare `a' to the result of
`b+c', yielding a `BOOLEAN' value.
File: gdb.info, Node: Automatically, Prev: Manually, Up: Setting
Having GDB infer the source language
------------------------------------
To have GDB set the working language automatically, use `set
language local' or `set language auto'. GDB then infers the working
language. That is, when your program stops in a frame (usually by
encountering a breakpoint), GDB sets the working language to the
language recorded for the function in that frame. If the language for
a frame is unknown (that is, if the function or block corresponding to
the frame was defined in a source file that does not have a recognized
extension), the current working language is not changed, and GDB issues
a warning.
This may not seem necessary for most programs, which are written
entirely in one source language. However, program modules and libraries
written in one source language can be used by a main program written in
a different source language. Using `set language auto' in this case
frees you from having to set the working language manually.
File: gdb.info, Node: Show, Next: Checks, Prev: Setting, Up: Languages
Displaying the language
=======================
The following commands help you find out which language is the
working language, and also what language source files were written in.
`show language'
Display the current working language. This is the language you
can use with commands such as `print' to build and compute
expressions that may involve variables in your program.
`info frame'
Display the source language for this frame. This language becomes
the working language if you use an identifier from this frame.
*Note Information about a frame: Frame Info, to identify the other
information listed here.
`info source'
Display the source language of this source file. *Note Examining
the Symbol Table: Symbols, to identify the other information
listed here.
In unusual circumstances, you may have source files with extensions
not in the standard list. You can then set the extension associated
with a language explicitly:
`set extension-language .EXT LANGUAGE'
Set source files with extension .EXT to be assumed to be in the
source language LANGUAGE.
`info extensions'
List all the filename extensions and the associated languages.
File: gdb.info, Node: Checks, Next: Support, Prev: Show, Up: Languages
Type and range checking
=======================
_Warning:_ In this release, the GDB commands for type and range
checking are included, but they do not yet have any effect. This
section documents the intended facilities.
Some languages are designed to guard you against making seemingly
common errors through a series of compile- and run-time checks. These
include checking the type of arguments to functions and operators, and
making sure mathematical overflows are caught at run time. Checks such
as these help to ensure a program's correctness once it has been
compiled by eliminating type mismatches, and providing active checks
for range errors when your program is running.
GDB can check for conditions like the above if you wish. Although
GDB does not check the statements in your program, it can check
expressions entered directly into GDB for evaluation via the `print'
command, for example. As with the working language, GDB can also
decide whether or not to check automatically based on your program's
source language. *Note Supported languages: Support, for the default
settings of supported languages.
* Menu:
* Type Checking:: An overview of type checking
* Range Checking:: An overview of range checking
File: gdb.info, Node: Type Checking, Next: Range Checking, Up: Checks
An overview of type checking
----------------------------
Some languages, such as Modula-2, are strongly typed, meaning that
the arguments to operators and functions have to be of the correct type,
otherwise an error occurs. These checks prevent type mismatch errors
from ever causing any run-time problems. For example,
1 + 2 => 3
but
error--> 1 + 2.3
The second example fails because the `CARDINAL' 1 is not
type-compatible with the `REAL' 2.3.
For the expressions you use in GDB commands, you can tell the GDB
type checker to skip checking; to treat any mismatches as errors and
abandon the expression; or to only issue warnings when type mismatches
occur, but evaluate the expression anyway. When you choose the last of
these, GDB evaluates expressions like the second example above, but
also issues a warning.
Even if you turn type checking off, there may be other reasons
related to type that prevent GDB from evaluating an expression. For
instance, GDB does not know how to add an `int' and a `struct foo'.
These particular type errors have nothing to do with the language in
use, and usually arise from expressions, such as the one described
above, which make little sense to evaluate anyway.
Each language defines to what degree it is strict about type. For
instance, both Modula-2 and C require the arguments to arithmetical
operators to be numbers. In C, enumerated types and pointers can be
represented as numbers, so that they are valid arguments to mathematical
operators. *Note Supported languages: Support, for further details on
specific languages.
GDB provides some additional commands for controlling the type
checker:
`set check type auto'
Set type checking on or off based on the current working language.
*Note Supported languages: Support, for the default settings for
each language.
`set check type on'
`set check type off'
Set type checking on or off, overriding the default setting for the
current working language. Issue a warning if the setting does not
match the language default. If any type mismatches occur in
evaluating an expression while type checking is on, GDB prints a
message and aborts evaluation of the expression.
`set check type warn'
Cause the type checker to issue warnings, but to always attempt to
evaluate the expression. Evaluating the expression may still be
impossible for other reasons. For example, GDB cannot add numbers
and structures.
`show type'
Show the current setting of the type checker, and whether or not
GDB is setting it automatically.
File: gdb.info, Node: Range Checking, Prev: Type Checking, Up: Checks
An overview of range checking
-----------------------------
In some languages (such as Modula-2), it is an error to exceed the
bounds of a type; this is enforced with run-time checks. Such range
checking is meant to ensure program correctness by making sure
computations do not overflow, or indices on an array element access do
not exceed the bounds of the array.
For expressions you use in GDB commands, you can tell GDB to treat
range errors in one of three ways: ignore them, always treat them as
errors and abandon the expression, or issue warnings but evaluate the
expression anyway.
A range error can result from numerical overflow, from exceeding an
array index bound, or when you type a constant that is not a member of
any type. Some languages, however, do not treat overflows as an error.
In many implementations of C, mathematical overflow causes the result
to "wrap around" to lower values--for example, if M is the largest
integer value, and S is the smallest, then
M + 1 => S
This, too, is specific to individual languages, and in some cases
specific to individual compilers or machines. *Note Supported
languages: Support, for further details on specific languages.
GDB provides some additional commands for controlling the range
checker:
`set check range auto'
Set range checking on or off based on the current working language.
*Note Supported languages: Support, for the default settings for
each language.
`set check range on'
`set check range off'
Set range checking on or off, overriding the default setting for
the current working language. A warning is issued if the setting
does not match the language default. If a range error occurs and
range checking is on, then a message is printed and evaluation of
the expression is aborted.
`set check range warn'
Output messages when the GDB range checker detects a range error,
but attempt to evaluate the expression anyway. Evaluating the
expression may still be impossible for other reasons, such as
accessing memory that the process does not own (a typical example
from many Unix systems).
`show range'
Show the current setting of the range checker, and whether or not
it is being set automatically by GDB.
File: gdb.info, Node: Support, Prev: Checks, Up: Languages
Supported languages
===================
GDB supports C, C++, Fortran, Java, Chill, assembly, and Modula-2.
Some GDB features may be used in expressions regardless of the language
you use: the GDB `@' and `::' operators, and the `{type}addr' construct
(*note Expressions: Expressions.) can be used with the constructs of
any supported language.
The following sections detail to what degree each source language is
supported by GDB. These sections are not meant to be language
tutorials or references, but serve only as a reference guide to what the
GDB expression parser accepts, and what input and output formats should
look like for different languages. There are many good books written
on each of these languages; please look to these for a language
reference or tutorial.
* Menu:
* C:: C and C++
* Modula-2:: Modula-2
* Chill:: Chill
File: gdb.info, Node: C, Next: Modula-2, Up: Support
C and C++
---------
Since C and C++ are so closely related, many features of GDB apply
to both languages. Whenever this is the case, we discuss those
languages together.
The C++ debugging facilities are jointly implemented by the C++
compiler and GDB. Therefore, to debug your C++ code effectively, you
must compile your C++ programs with a supported C++ compiler, such as
GNU `g++', or the HP ANSI C++ compiler (`aCC').
For best results when using GNU C++, use the stabs debugging format.
You can select that format explicitly with the `g++' command-line
options `-gstabs' or `-gstabs+'. See *Note Options for Debugging Your
Program or GNU CC: (gcc.info)Debugging Options, for more information.
* Menu:
* C Operators:: C and C++ operators
* C Constants:: C and C++ constants
* C plus plus expressions:: C++ expressions
* C Defaults:: Default settings for C and C++
* C Checks:: C and C++ type and range checks
* Debugging C:: GDB and C
* Debugging C plus plus:: GDB features for C++
File: gdb.info, Node: C Operators, Next: C Constants, Up: C
C and C++ operators
...................
Operators must be defined on values of specific types. For instance,
`+' is defined on numbers, but not on structures. Operators are often
defined on groups of types.
For the purposes of C and C++, the following definitions hold:
* _Integral types_ include `int' with any of its storage-class
specifiers; `char'; `enum'; and, for C++, `bool'.
* _Floating-point types_ include `float', `double', and `long
double' (if supported by the target platform).
* _Pointer types_ include all types defined as `(TYPE *)'.
* _Scalar types_ include all of the above.
The following operators are supported. They are listed here in order
of increasing precedence:
`,'
The comma or sequencing operator. Expressions in a
comma-separated list are evaluated from left to right, with the
result of the entire expression being the last expression
evaluated.
`='
Assignment. The value of an assignment expression is the value
assigned. Defined on scalar types.
`OP='
Used in an expression of the form `A OP= B', and translated to
`A = A OP B'. `OP=' and `=' have the same precedence. OP is any
one of the operators `|', `^', `&', `<<', `>>', `+', `-', `*',
`/', `%'.
`?:'
The ternary operator. `A ? B : C' can be thought of as: if A
then B else C. A should be of an integral type.
`||'
Logical OR. Defined on integral types.
`&&'
Logical AND. Defined on integral types.
`|'
Bitwise OR. Defined on integral types.
`^'
Bitwise exclusive-OR. Defined on integral types.
`&'
Bitwise AND. Defined on integral types.
`==, !='
Equality and inequality. Defined on scalar types. The value of
these expressions is 0 for false and non-zero for true.
`<, >, <=, >='
Less than, greater than, less than or equal, greater than or equal.
Defined on scalar types. The value of these expressions is 0 for
false and non-zero for true.
`<<, >>'
left shift, and right shift. Defined on integral types.
`@'
The GDB "artificial array" operator (*note Expressions:
Expressions.).
`+, -'
Addition and subtraction. Defined on integral types,
floating-point types and pointer types.
`*, /, %'
Multiplication, division, and modulus. Multiplication and
division are defined on integral and floating-point types.
Modulus is defined on integral types.
`++, --'
Increment and decrement. When appearing before a variable, the
operation is performed before the variable is used in an
expression; when appearing after it, the variable's value is used
before the operation takes place.
`*'
Pointer dereferencing. Defined on pointer types. Same precedence
as `++'.
`&'
Address operator. Defined on variables. Same precedence as `++'.
For debugging C++, GDB implements a use of `&' beyond what is
allowed in the C++ language itself: you can use `&(&REF)' (or, if
you prefer, simply `&&REF') to examine the address where a C++
reference variable (declared with `&REF') is stored.
`-'
Negative. Defined on integral and floating-point types. Same
precedence as `++'.
`!'
Logical negation. Defined on integral types. Same precedence as
`++'.
`~'
Bitwise complement operator. Defined on integral types. Same
precedence as `++'.
`., ->'
Structure member, and pointer-to-structure member. For
convenience, GDB regards the two as equivalent, choosing whether
to dereference a pointer based on the stored type information.
Defined on `struct' and `union' data.
`.*, ->*'
Dereferences of pointers to members.
`[]'
Array indexing. `A[I]' is defined as `*(A+I)'. Same precedence
as `->'.
`()'
Function parameter list. Same precedence as `->'.
`::'
C++ scope resolution operator. Defined on `struct', `union', and
`class' types.
`::'
Doubled colons also represent the GDB scope operator (*note
Expressions: Expressions.). Same precedence as `::', above.
If an operator is redefined in the user code, GDB usually attempts
to invoke the redefined version instead of using the operator's
predefined meaning.
* Menu:
* C Constants::
File: gdb.info, Node: C Constants, Next: C plus plus expressions, Prev: C Operators, Up: C
C and C++ constants
...................
GDB allows you to express the constants of C and C++ in the
following ways:
* Integer constants are a sequence of digits. Octal constants are
specified by a leading `0' (i.e. zero), and hexadecimal constants
by a leading `0x' or `0X'. Constants may also end with a letter
`l', specifying that the constant should be treated as a `long'
value.
* Floating point constants are a sequence of digits, followed by a
decimal point, followed by a sequence of digits, and optionally
followed by an exponent. An exponent is of the form:
`e[[+]|-]NNN', where NNN is another sequence of digits. The `+'
is optional for positive exponents. A floating-point constant may
also end with a letter `f' or `F', specifying that the constant
should be treated as being of the `float' (as opposed to the
default `double') type; or with a letter `l' or `L', which
specifies a `long double' constant.
* Enumerated constants consist of enumerated identifiers, or their
integral equivalents.
* Character constants are a single character surrounded by single
quotes (`''), or a number--the ordinal value of the corresponding
character (usually its ASCII value). Within quotes, the single
character may be represented by a letter or by "escape sequences",
which are of the form `\NNN', where NNN is the octal representation
of the character's ordinal value; or of the form `\X', where `X'
is a predefined special character--for example, `\n' for newline.
* String constants are a sequence of character constants surrounded
by double quotes (`"'). Any valid character constant (as described
above) may appear. Double quotes within the string must be
preceded by a backslash, so for instance `"a\"b'c"' is a string of
five characters.
* Pointer constants are an integral value. You can also write
pointers to constants using the C operator `&'.
* Array constants are comma-separated lists surrounded by braces `{'
and `}'; for example, `{1,2,3}' is a three-element array of
integers, `{{1,2}, {3,4}, {5,6}}' is a three-by-two array, and
`{&"hi", &"there", &"fred"}' is a three-element array of pointers.
* Menu:
* C plus plus expressions::
* C Defaults::
* C Checks::
* Debugging C::
File: gdb.info, Node: C plus plus expressions, Next: C Defaults, Prev: C Constants, Up: C
C++ expressions
...............
GDB expression handling can interpret most C++ expressions.
_Warning:_ GDB can only debug C++ code if you use the proper
compiler. Typically, C++ debugging depends on the use of
additional debugging information in the symbol table, and thus
requires special support. In particular, if your compiler
generates a.out, MIPS ECOFF, RS/6000 XCOFF, or ELF with stabs
extensions to the symbol table, these facilities are all
available. (With GNU CC, you can use the `-gstabs' option to
request stabs debugging extensions explicitly.) Where the object
code format is standard COFF or DWARF in ELF, on the other hand,
most of the C++ support in GDB does _not_ work.
1. Member function calls are allowed; you can use expressions like
count = aml->GetOriginal(x, y)
2. While a member function is active (in the selected stack frame),
your expressions have the same namespace available as the member
function; that is, GDB allows implicit references to the class
instance pointer `this' following the same rules as C++.
3. You can call overloaded functions; GDB resolves the function call
to the right definition, with some restrictions. GDB does not
perform overload resolution involving user-defined type
conversions, calls to constructors, or instantiations of templates
that do not exist in the program. It also cannot handle ellipsis
argument lists or default arguments.
It does perform integral conversions and promotions, floating-point
promotions, arithmetic conversions, pointer conversions,
conversions of class objects to base classes, and standard
conversions such as those of functions or arrays to pointers; it
requires an exact match on the number of function arguments.
Overload resolution is always performed, unless you have specified
`set overload-resolution off'. *Note GDB features for C++:
Debugging C plus plus.
You must specify `set overload-resolution off' in order to use an
explicit function signature to call an overloaded function, as in
p 'foo(char,int)'('x', 13)
The GDB command-completion facility can simplify this; see *Note
Command completion: Completion.
4. GDB understands variables declared as C++ references; you can use
them in expressions just as you do in C++ source--they are
automatically dereferenced.
In the parameter list shown when GDB displays a frame, the values
of reference variables are not displayed (unlike other variables);
this avoids clutter, since references are often used for large
structures. The _address_ of a reference variable is always
shown, unless you have specified `set print address off'.
5. GDB supports the C++ name resolution operator `::'--your
expressions can use it just as expressions in your program do.
Since one scope may be defined in another, you can use `::'
repeatedly if necessary, for example in an expression like
`SCOPE1::SCOPE2::NAME'. GDB also allows resolving name scope by
reference to source files, in both C and C++ debugging (*note
Program variables: Variables.).
In addition, when used with HP's C++ compiler, GDB supports calling
virtual functions correctly, printing out virtual bases of objects,
calling functions in a base subobject, casting objects, and invoking
user-defined operators.
File: gdb.info, Node: C Defaults, Next: C Checks, Prev: C plus plus expressions, Up: C
C and C++ defaults
..................
If you allow GDB to set type and range checking automatically, they
both default to `off' whenever the working language changes to C or
C++. This happens regardless of whether you or GDB selects the working
language.
If you allow GDB to set the language automatically, it recognizes
source files whose names end with `.c', `.C', or `.cc', etc, and when
GDB enters code compiled from one of these files, it sets the working
language to C or C++. *Note Having GDB infer the source language:
Automatically, for further details.
File: gdb.info, Node: C Checks, Next: Debugging C, Prev: C Defaults, Up: C
C and C++ type and range checks
...............................
By default, when GDB parses C or C++ expressions, type checking is
not used. However, if you turn type checking on, GDB considers two
variables type equivalent if:
* The two variables are structured and have the same structure,
union, or enumerated tag.
* The two variables have the same type name, or types that have been
declared equivalent through `typedef'.
Range checking, if turned on, is done on mathematical operations.
Array indices are not checked, since they are often used to index a
pointer that is not itself an array.
File: gdb.info, Node: Debugging C, Next: Debugging C plus plus, Prev: C Checks, Up: C
GDB and C
.........
The `set print union' and `show print union' commands apply to the
`union' type. When set to `on', any `union' that is inside a `struct'
or `class' is also printed. Otherwise, it appears as `{...}'.
The `@' operator aids in the debugging of dynamic arrays, formed
with pointers and a memory allocation function. *Note Expressions:
Expressions.
* Menu:
* Debugging C plus plus::
File: gdb.info, Node: Debugging C plus plus, Prev: Debugging C, Up: C
GDB features for C++
....................
Some GDB commands are particularly useful with C++, and some are
designed specifically for use with C++. Here is a summary:
`breakpoint menus'
When you want a breakpoint in a function whose name is overloaded,
GDB breakpoint menus help you specify which function definition
you want. *Note Breakpoint menus: Breakpoint Menus.
`rbreak REGEX'
Setting breakpoints using regular expressions is helpful for
setting breakpoints on overloaded functions that are not members
of any special classes. *Note Setting breakpoints: Set Breaks.
`catch throw'
`catch catch'
Debug C++ exception handling using these commands. *Note Setting
catchpoints: Set Catchpoints.
`ptype TYPENAME'
Print inheritance relationships as well as other information for
type TYPENAME. *Note Examining the Symbol Table: Symbols.
`set print demangle'
`show print demangle'
`set print asm-demangle'
`show print asm-demangle'
Control whether C++ symbols display in their source form, both when
displaying code as C++ source and when displaying disassemblies.
*Note Print settings: Print Settings.
`set print object'
`show print object'
Choose whether to print derived (actual) or declared types of
objects. *Note Print settings: Print Settings.
`set print vtbl'
`show print vtbl'
Control the format for printing virtual function tables. *Note
Print settings: Print Settings. (The `vtbl' commands do not work
on programs compiled with the HP ANSI C++ compiler (`aCC').)
`set overload-resolution on'
Enable overload resolution for C++ expression evaluation. The
default is on. For overloaded functions, GDB evaluates the
arguments and searches for a function whose signature matches the
argument types, using the standard C++ conversion rules (see *Note
C++ expressions: C plus plus expressions, for details). If it
cannot find a match, it emits a message.
`set overload-resolution off'
Disable overload resolution for C++ expression evaluation. For
overloaded functions that are not class member functions, GDB
chooses the first function of the specified name that it finds in
the symbol table, whether or not its arguments are of the correct
type. For overloaded functions that are class member functions,
GDB searches for a function whose signature _exactly_ matches the
argument types.
`Overloaded symbol names'
You can specify a particular definition of an overloaded symbol,
using the same notation that is used to declare such symbols in
C++: type `SYMBOL(TYPES)' rather than just SYMBOL. You can also
use the GDB command-line word completion facilities to list the
available choices, or to finish the type list for you. *Note
Command completion: Completion, for details on how to do this.
File: gdb.info, Node: Modula-2, Next: Chill, Prev: C, Up: Support
Modula-2
--------
The extensions made to GDB to support Modula-2 only support output
from the GNU Modula-2 compiler (which is currently being developed).
Other Modula-2 compilers are not currently supported, and attempting to
debug executables produced by them is most likely to give an error as
GDB reads in the executable's symbol table.
* Menu:
* M2 Operators:: Built-in operators
* Built-In Func/Proc:: Built-in functions and procedures
* M2 Constants:: Modula-2 constants
* M2 Defaults:: Default settings for Modula-2
* Deviations:: Deviations from standard Modula-2
* M2 Checks:: Modula-2 type and range checks
* M2 Scope:: The scope operators `::' and `.'
* GDB/M2:: GDB and Modula-2
File: gdb.info, Node: M2 Operators, Next: Built-In Func/Proc, Up: Modula-2
Operators
.........
Operators must be defined on values of specific types. For instance,
`+' is defined on numbers, but not on structures. Operators are often
defined on groups of types. For the purposes of Modula-2, the
following definitions hold:
* _Integral types_ consist of `INTEGER', `CARDINAL', and their
subranges.
* _Character types_ consist of `CHAR' and its subranges.
* _Floating-point types_ consist of `REAL'.
* _Pointer types_ consist of anything declared as `POINTER TO TYPE'.
* _Scalar types_ consist of all of the above.
* _Set types_ consist of `SET' and `BITSET' types.
* _Boolean types_ consist of `BOOLEAN'.
The following operators are supported, and appear in order of
increasing precedence:
`,'
Function argument or array index separator.
`:='
Assignment. The value of VAR `:=' VALUE is VALUE.
`<, >'
Less than, greater than on integral, floating-point, or enumerated
types.
`<=, >='
Less than or equal to, greater than or equal to on integral,
floating-point and enumerated types, or set inclusion on set
types. Same precedence as `<'.
`=, <>, #'
Equality and two ways of expressing inequality, valid on scalar
types. Same precedence as `<'. In GDB scripts, only `<>' is
available for inequality, since `#' conflicts with the script
comment character.
`IN'
Set membership. Defined on set types and the types of their
members. Same precedence as `<'.
`OR'
Boolean disjunction. Defined on boolean types.
`AND, &'
Boolean conjunction. Defined on boolean types.
`@'
The GDB "artificial array" operator (*note Expressions:
Expressions.).
`+, -'
Addition and subtraction on integral and floating-point types, or
union and difference on set types.
`*'
Multiplication on integral and floating-point types, or set
intersection on set types.
`/'
Division on floating-point types, or symmetric set difference on
set types. Same precedence as `*'.
`DIV, MOD'
Integer division and remainder. Defined on integral types. Same
precedence as `*'.
`-'
Negative. Defined on `INTEGER' and `REAL' data.
`^'
Pointer dereferencing. Defined on pointer types.
`NOT'
Boolean negation. Defined on boolean types. Same precedence as
`^'.
`.'
`RECORD' field selector. Defined on `RECORD' data. Same
precedence as `^'.
`[]'
Array indexing. Defined on `ARRAY' data. Same precedence as `^'.
`()'
Procedure argument list. Defined on `PROCEDURE' objects. Same
precedence as `^'.
`::, .'
GDB and Modula-2 scope operators.
_Warning:_ Sets and their operations are not yet supported, so GDB
treats the use of the operator `IN', or the use of operators `+',
`-', `*', `/', `=', , `<>', `#', `<=', and `>=' on sets as an
error.
Go to most recent revision | Compare with Previous | Blame | View Log