Subversion Repositories or1k

#
# For a description of the syntax of this configuration file,
# see Documentation/kbuild/config-language.txt.
#
mainmenu_name "Linux/SH64 Kernel Configuration"

define_bool CONFIG_SUPERH y

define_bool CONFIG_UID16 y
define_bool CONFIG_RWSEM_GENERIC_SPINLOCK y
define_bool CONFIG_RWSEM_XCHGADD_ALGORITHM n

mainmenu_option next_comment
comment 'Code maturity level options'
bool 'Prompt for development and/or incomplete code/drivers' CONFIG_EXPERIMENTAL
endmenu

mainmenu_option next_comment
comment 'Loadable module support'
bool 'Enable loadable module support' CONFIG_MODULES
if [ "$CONFIG_MODULES" = "y" ]; then
   bool '  Set version information on all module symbols' CONFIG_MODVERSIONS
   bool '  Kernel module loader' CONFIG_KMOD
fi
endmenu

mainmenu_option next_comment
comment 'System type'
choice 'SuperH system type'                                     \
        "Generic                CONFIG_SH_GENERIC               \
         Simulator              CONFIG_SH_SIMULATOR             \
         Cayman                 CONFIG_SH_CAYMAN                \
         ST50-Harp              CONFIG_SH_HARP" Simulator
endmenu

mainmenu_option next_comment
comment 'Processor type and features'
comment 'Processor options'
choice 'Processor family'                                       \
        "SH-5                   CONFIG_CPU_SH5" SH-5

if [ "$CONFIG_CPU_SH5" = "y" ]; then
   choice 'Processor type' \
        "SH5-101                CONFIG_CPU_SUBTYPE_SH5_101      \
         SH5-103                CONFIG_CPU_SUBTYPE_SH5_103" SH5-101
fi

choice 'Endianness' \
       "Little-Endian           CONFIG_LITTLE_ENDIAN            \
        Big-Endian              CONFIG_BIG_ENDIAN" Little-Endian

bool 'Flush floating point denorms to zero' CONFIG_SH64_FPU_DENORM_FLUSH
choice 'Page table levels' \
        "2                      CONFIG_SH64_PGTABLE_2_LEVEL \
         3                      CONFIG_SH64_PGTABLE_3_LEVEL" 2

bool 'Fixup misaligned loads/stores occurring in user mode' CONFIG_SH64_USER_MISALIGNED_FIXUP

# Use 32-bit addressing for now.
# EMI based.
# P2 (UNCACHED) required to use identity mapping
# P1 (CACHED) assumes non-identity.

#
# Memory options
#
comment 'Memory options'

int 'Memory size (in MB)' CONFIG_MEMORY_SIZE_IN_MB 64
hex 'Cached Area Offset' CONFIG_CACHED_MEMORY_OFFSET 20000000
hex 'Uncached Area Offset' CONFIG_UNCACHED_MEMORY_OFFSET 00000000
hex 'Physical memory start address' CONFIG_MEMORY_START 80000000

#
# Cache options
#
comment 'Cache options'
bool 'DCache Disabling' CONFIG_DCACHE_DISABLED

if [ "$CONFIG_SH_SIMULATOR" != "y" -a \
     "$CONFIG_DCACHE_DISABLED" != "y" ]; then
     choice 'DCache mode'                                 \
         "Write-back             CONFIG_DCACHE_WRITE_BACK \
          Write-through          CONFIG_DCACHE_WRITE_THROUGH" Write-back
fi

bool 'ICache Disabling' CONFIG_ICACHE_DISABLED


#
# CPU Subtype specific options (errata and such)
#
comment 'CPU Subtype specific options'
if [ "$CONFIG_CPU_SUBTYPE_SH5_101" = "y" ]; then
  bool "Include workaround for SH5-101 cut2 silicon defect ID2815" CONFIG_SH64_ID2815_WORKAROUND
fi

endmenu

mainmenu_option next_comment
comment 'General setup'

define_bool CONFIG_ISA n
define_bool CONFIG_SBUS n

bool 'Networking support' CONFIG_NET

bool 'PCI support' CONFIG_PCI
if [ "$CONFIG_SH_SIMULATOR" = "y" ]; then
  define_bool CONFIG_PCI n
  define_bool CONFIG_NET n
fi

if [ "$CONFIG_SH_HARP" = "y" ]; then
  define_bool CONFIG_PCI n
  define_bool CONFIG_NET y
  define_bool CONFIG_NET_PCI y
fi

if [ "$CONFIG_PCI" = "y" ]; then
   choice '  PCI access mode' \
        "BIOS           CONFIG_PCI_GOBIOS       \
         Direct         CONFIG_PCI_GODIRECT     \
         Any            CONFIG_PCI_GOANY"       Any
   if [ "$CONFIG_PCI_GOBIOS" = "y" -o "$CONFIG_PCI_GOANY" = "y" ]; then
      define_bool CONFIG_PCI_BIOS y
   fi
   if [ "$CONFIG_PCI_GODIRECT" = "y" -o "$CONFIG_PCI_GOANY" = "y" ]; then
      define_bool CONFIG_PCI_DIRECT y
   fi
fi

source drivers/pci/Config.in

# bool 'Support for hot-pluggable devices' CONFIG_HOTPLUG
# 
define_bool CONFIG_HOTPLUG n

if [ "$CONFIG_HOTPLUG" = "y" ] ; then
   source drivers/pcmcia/Config.in
else
   define_bool CONFIG_PCMCIA n
fi

bool 'System V IPC' CONFIG_SYSVIPC
bool 'BSD Process Accounting' CONFIG_BSD_PROCESS_ACCT
# bool 'Sysctl support' CONFIG_SYSCTL
define_bool CONFIG_SYSCTL y

if [ "$CONFIG_PROC_FS" = "y" ]; then
   choice 'Kernel core (/proc/kcore) format' \
        "ELF            CONFIG_KCORE_ELF        \
         A.OUT          CONFIG_KCORE_AOUT" ELF
fi
tristate 'Kernel support for ELF binaries' CONFIG_BINFMT_ELF
tristate 'Kernel support for MISC binaries' CONFIG_BINFMT_MISC

bool 'Select task to kill on out of memory condition' CONFIG_OOM_KILLER

# source drivers/parport/Config.in

endmenu

# source drivers/mtd/Config.in

source drivers/block/Config.in

if [ "$CONFIG_NET" = "y" ]; then
   source net/Config.in
fi

mainmenu_option next_comment
comment 'ATA/IDE/MFM/RLL support'

tristate 'ATA/IDE/MFM/RLL support' CONFIG_IDE

if [ "$CONFIG_IDE" != "n" ]; then
  source drivers/ide/Config.in
else
   define_bool CONFIG_BLK_DEV_HD n
fi
endmenu

mainmenu_option next_comment
comment 'SCSI support'

 tristate 'SCSI support' CONFIG_SCSI
##define_bool CONFIG_SCSI n

if [ "$CONFIG_SCSI" != "n" ]; then
   source drivers/scsi/Config.in
fi
endmenu

# source drivers/ieee1394/Config.in

if [ "$CONFIG_NET" = "y" ]; then
   mainmenu_option next_comment
   comment 'Network device support'

   bool 'Network device support' CONFIG_NETDEVICES
   if [ "$CONFIG_NETDEVICES" = "y" ]; then
      source drivers/net/Config.in
      if [ "$CONFIG_ATM" = "y" -o "$CONFIG_ATM" = "m" ]; then
         source drivers/atm/Config.in
      fi
   fi
   endmenu
fi

#
# input before char - char/joystick depends on it. As does USB.
#
source drivers/input/Config.in

mainmenu_option next_comment
comment 'Character devices'

bool 'Virtual terminal' CONFIG_VT

if [ "$CONFIG_VT" = "y" ]; then
   bool '  Support for console on virtual terminal' CONFIG_VT_CONSOLE
fi


# insert for SCIF serial console support 
tristate 'Serial (SCI, SCIF) support' CONFIG_SH_SCI
tristate 'Serial (8250, 16450, 16550 or compatible) support' CONFIG_SERIAL

if [ "$CONFIG_SERIAL" = "y" -o "$CONFIG_SH_SCI" = "y" ]; then
   bool '  Support for console on serial port' CONFIG_SERIAL_CONSOLE
fi


comment 'Unix 98 PTY support'
bool 'Unix98 PTY support' CONFIG_UNIX98_PTYS
if [ "$CONFIG_UNIX98_PTYS" = "y" ]; then
   int 'Maximum number of Unix98 PTYs in use (0-2048)' CONFIG_UNIX98_PTY_COUNT 256
fi
if [ "$CONFIG_PARPORT" != "n" ]; then
   dep_tristate 'Parallel printer support' CONFIG_PRINTER $CONFIG_PARPORT
   if [ "$CONFIG_PRINTER" != "n" ]; then
      bool '  Support for console on line printer' CONFIG_LP_CONSOLE
   fi
   dep_tristate 'Support for user-space parallel port device drivers' CONFIG_PPDEV $CONFIG_PARPORT
fi

bool 'Heartbeat LED' CONFIG_HEARTBEAT
dep_bool 'Support for HDSP-253 LED' CONFIG_HDSP253_LED $CONFIG_SH_CAYMAN
tristate 'DMA controller (DMAC) support' CONFIG_SH_DMA
bool 'PS/2 mouse (aka "auxiliary device") support' CONFIG_PSMOUSE

mainmenu_option next_comment
comment 'Watchdog Cards'
bool 'Watchdog Timer Support' CONFIG_WATCHDOG
if [ "$CONFIG_WATCHDOG" != "n" ]; then
   bool '  Disable watchdog shutdown on close' CONFIG_WATCHDOG_NOWAYOUT
   dep_tristate '  SuperH Watchdog' CONFIG_SH_WDT $CONFIG_SUPERH
fi
endmenu

endmenu

if [ "$CONFIG_HOTPLUG" = "y" -a "$CONFIG_PCMCIA" != "n" ]; then
   source drivers/char/pcmcia/Config.in
fi

source fs/Config.in

source drivers/media/Config.in


if [ "$CONFIG_VT" = "y" ]; then
   mainmenu_option next_comment
   comment 'Console drivers'
   bool 'VGA text console' CONFIG_VGA_CONSOLE
   bool 'Video mode selection support' CONFIG_VIDEO_SELECT
   if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
      tristate 'MDA text console (dual-headed) (EXPERIMENTAL)' CONFIG_MDA_CONSOLE
      source drivers/video/Config.in
   fi
   endmenu
fi


mainmenu_option next_comment
comment 'Sound'

tristate 'Sound card support' CONFIG_SOUND
# define_bool CONFIG_SOUND n

if [ "$CONFIG_SOUND" != "n" ]; then
   source drivers/sound/Config.in
fi
endmenu

source drivers/usb/Config.in

mainmenu_option next_comment
comment 'Kernel hacking'

bool 'Magic SysRq key' CONFIG_MAGIC_SYSRQ
bool 'GDB Stub kernel debug' CONFIG_DEBUG_KERNEL_WITH_GDB_STUB
bool "Debug: audit page tables on return from syscall/exception/interrupt" CONFIG_SH64_PAGE_TABLE_AUDIT
dep_bool "Debug: report TLB fill/purge activity through /proc/tlb" CONFIG_SH64_PROC_TLB $CONFIG_PROC_FS
dep_bool "Debug: report ASIDS through /proc/asids" CONFIG_SH64_PROC_ASIDS $CONFIG_PROC_FS

int 'Kernel messages buffer length shift (0 = default)' CONFIG_LOG_BUF_SHIFT 0

endmenu

source lib/Config.in
source crypto/Config.in