Subversion Repositories or1k

#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Block devices'

tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
if [ "$CONFIG_AMIGA" = "y" ]; then
   tristate 'Amiga floppy support' CONFIG_AMIGA_FLOPPY
fi
if [ "$CONFIG_ATARI" = "y" ]; then
   tristate 'Atari floppy support' CONFIG_ATARI_FLOPPY
fi
if [ "$CONFIG_MAC" = "y" ]; then
   dep_bool 'Macintosh IIfx/Quadra 900/Quadra 950 floppy support (EXPERIMENTAL)' CONFIG_BLK_DEV_SWIM_IOP $CONFIG_EXPERIMENTAL
fi
if [ "$CONFIG_MCA" = "y" ]; then
   tristate 'PS/2 ESDI hard disk support' CONFIG_BLK_DEV_PS2
fi
if [ "$CONFIG_ZORRO" = "y" ]; then
   tristate 'Amiga Zorro II ramdisk support' CONFIG_AMIGA_Z2RAM
fi
if [ "$CONFIG_ATARI" = "y" ]; then
   tristate 'Atari ACSI support' CONFIG_ATARI_ACSI
   if [ "$CONFIG_ATARI_ACSI" != "n" ]; then
      comment 'Some devices (e.g. CD jukebox) support multiple LUNs'
      bool '  Probe all LUNs on each ACSI device' CONFIG_ACSI_MULTI_LUN
      tristate '  Atari SLM laser printer support' CONFIG_ATARI_SLM
   fi
fi
dep_tristate 'XT hard disk support' CONFIG_BLK_DEV_XD $CONFIG_ISA
dep_tristate 'Parallel port IDE device support' CONFIG_PARIDE $CONFIG_PARPORT
if [ "$CONFIG_PARIDE" = "y" -o "$CONFIG_PARIDE" = "m" ]; then
   source drivers/block/paride/Config.in
fi
dep_tristate 'Compaq SMART2 support' CONFIG_BLK_CPQ_DA $CONFIG_PCI
dep_tristate 'Compaq Smart Array 5xxx support' CONFIG_BLK_CPQ_CISS_DA $CONFIG_PCI 
dep_mbool '       SCSI tape drive support for Smart Array 5xxx' CONFIG_CISS_SCSI_TAPE $CONFIG_BLK_CPQ_CISS_DA $CONFIG_SCSI
dep_mbool '       Enable monitor thread' CONFIG_CISS_MONITOR_THREAD $CONFIG_BLK_CPQ_CISS_DA
dep_tristate 'Mylex DAC960/DAC1100 PCI RAID Controller support' CONFIG_BLK_DEV_DAC960 $CONFIG_PCI
dep_tristate 'Micro Memory MM5415 Battery Backed RAM support (EXPERIMENTAL)' CONFIG_BLK_DEV_UMEM $CONFIG_PCI $CONFIG_EXPERIMENTAL

tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
dep_tristate 'Network block device support' CONFIG_BLK_DEV_NBD $CONFIG_NET

tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" -o "$CONFIG_BLK_DEV_RAM" = "m" ]; then
   int '  Default RAM disk size' CONFIG_BLK_DEV_RAM_SIZE 4096
fi
dep_bool '  Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD $CONFIG_BLK_DEV_RAM

bool 'Per partition statistics in /proc/partitions' CONFIG_BLK_STATS

endmenu