URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [char/] [istallion.c] - Rev 1765
Compare with Previous | Blame | View Log
/*****************************************************************************/ /* * istallion.c -- stallion intelligent multiport serial driver. * * Copyright (C) 1996-1999 Stallion Technologies (support@stallion.oz.au). * Copyright (C) 1994-1996 Greg Ungerer. * * This code is loosely based on the Linux serial driver, written by * Linus Torvalds, Theodore T'so and others. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /*****************************************************************************/ #include <linux/config.h> #include <linux/module.h> #include <linux/slab.h> #include <linux/interrupt.h> #include <linux/tty.h> #include <linux/tty_flip.h> #include <linux/serial.h> #include <linux/cdk.h> #include <linux/comstats.h> #include <linux/version.h> #include <linux/istallion.h> #include <linux/ioport.h> #include <linux/delay.h> #include <linux/init.h> #include <linux/devfs_fs_kernel.h> #include <asm/io.h> #include <asm/uaccess.h> #ifdef CONFIG_PCI #include <linux/pci.h> #endif /*****************************************************************************/ /* * Define different board types. Not all of the following board types * are supported by this driver. But I will use the standard "assigned" * board numbers. Currently supported boards are abbreviated as: * ECP = EasyConnection 8/64, ONB = ONboard, BBY = Brumby and * STAL = Stallion. */ #define BRD_UNKNOWN 0 #define BRD_STALLION 1 #define BRD_BRUMBY4 2 #define BRD_ONBOARD2 3 #define BRD_ONBOARD 4 #define BRD_BRUMBY8 5 #define BRD_BRUMBY16 6 #define BRD_ONBOARDE 7 #define BRD_ONBOARD32 9 #define BRD_ONBOARD2_32 10 #define BRD_ONBOARDRS 11 #define BRD_EASYIO 20 #define BRD_ECH 21 #define BRD_ECHMC 22 #define BRD_ECP 23 #define BRD_ECPE 24 #define BRD_ECPMC 25 #define BRD_ECHPCI 26 #define BRD_ECH64PCI 27 #define BRD_EASYIOPCI 28 #define BRD_ECPPCI 29 #define BRD_BRUMBY BRD_BRUMBY4 /* * Define a configuration structure to hold the board configuration. * Need to set this up in the code (for now) with the boards that are * to be configured into the system. This is what needs to be modified * when adding/removing/modifying boards. Each line entry in the * stli_brdconf[] array is a board. Each line contains io/irq/memory * ranges for that board (as well as what type of board it is). * Some examples: * { BRD_ECP, 0x2a0, 0, 0xcc000, 0, 0 }, * This line will configure an EasyConnection 8/64 at io address 2a0, * and shared memory address of cc000. Multiple EasyConnection 8/64 * boards can share the same shared memory address space. No interrupt * is required for this board type. * Another example: * { BRD_ECPE, 0x5000, 0, 0x80000000, 0, 0 }, * This line will configure an EasyConnection 8/64 EISA in slot 5 and * shared memory address of 0x80000000 (2 GByte). Multiple * EasyConnection 8/64 EISA boards can share the same shared memory * address space. No interrupt is required for this board type. * Another example: * { BRD_ONBOARD, 0x240, 0, 0xd0000, 0, 0 }, * This line will configure an ONboard (ISA type) at io address 240, * and shared memory address of d0000. Multiple ONboards can share * the same shared memory address space. No interrupt required. * Another example: * { BRD_BRUMBY4, 0x360, 0, 0xc8000, 0, 0 }, * This line will configure a Brumby board (any number of ports!) at * io address 360 and shared memory address of c8000. All Brumby boards * configured into a system must have their own separate io and memory * addresses. No interrupt is required. * Another example: * { BRD_STALLION, 0x330, 0, 0xd0000, 0, 0 }, * This line will configure an original Stallion board at io address 330 * and shared memory address d0000 (this would only be valid for a "V4.0" * or Rev.O Stallion board). All Stallion boards configured into the * system must have their own separate io and memory addresses. No * interrupt is required. */ typedef struct { int brdtype; int ioaddr1; int ioaddr2; unsigned long memaddr; int irq; int irqtype; } stlconf_t; static stlconf_t stli_brdconf[] = { /*{ BRD_ECP, 0x2a0, 0, 0xcc000, 0, 0 },*/ }; static int stli_nrbrds = sizeof(stli_brdconf) / sizeof(stlconf_t); /* * There is some experimental EISA board detection code in this driver. * By default it is disabled, but for those that want to try it out, * then set the define below to be 1. */ #define STLI_EISAPROBE 0 static devfs_handle_t devfs_handle; /*****************************************************************************/ /* * Define some important driver characteristics. Device major numbers * allocated as per Linux Device Registry. */ #ifndef STL_SIOMEMMAJOR #define STL_SIOMEMMAJOR 28 #endif #ifndef STL_SERIALMAJOR #define STL_SERIALMAJOR 24 #endif #ifndef STL_CALLOUTMAJOR #define STL_CALLOUTMAJOR 25 #endif #define STL_DRVTYPSERIAL 1 #define STL_DRVTYPCALLOUT 2 /*****************************************************************************/ /* * Define our local driver identity first. Set up stuff to deal with * all the local structures required by a serial tty driver. */ static char *stli_drvtitle = "Stallion Intelligent Multiport Serial Driver"; static char *stli_drvname = "istallion"; static char *stli_drvversion = "5.6.0"; static char *stli_serialname = "ttyE"; static char *stli_calloutname = "cue"; static struct tty_driver stli_serial; static struct tty_driver stli_callout; static struct tty_struct *stli_ttys[STL_MAXDEVS]; static struct termios *stli_termios[STL_MAXDEVS]; static struct termios *stli_termioslocked[STL_MAXDEVS]; static int stli_refcount; /* * We will need to allocate a temporary write buffer for chars that * come direct from user space. The problem is that a copy from user * space might cause a page fault (typically on a system that is * swapping!). All ports will share one buffer - since if the system * is already swapping a shared buffer won't make things any worse. */ static char *stli_tmpwritebuf; static DECLARE_MUTEX(stli_tmpwritesem); #define STLI_TXBUFSIZE 4096 /* * Use a fast local buffer for cooked characters. Typically a whole * bunch of cooked characters come in for a port, 1 at a time. So we * save those up into a local buffer, then write out the whole lot * with a large memcpy. Just use 1 buffer for all ports, since its * use it is only need for short periods of time by each port. */ static char *stli_txcookbuf; static int stli_txcooksize; static int stli_txcookrealsize; static struct tty_struct *stli_txcooktty; /* * Define a local default termios struct. All ports will be created * with this termios initially. Basically all it defines is a raw port * at 9600 baud, 8 data bits, no parity, 1 stop bit. */ static struct termios stli_deftermios = { c_cflag: (B9600 | CS8 | CREAD | HUPCL | CLOCAL), c_cc: INIT_C_CC, }; /* * Define global stats structures. Not used often, and can be * re-used for each stats call. */ static comstats_t stli_comstats; static combrd_t stli_brdstats; static asystats_t stli_cdkstats; static stlibrd_t stli_dummybrd; static stliport_t stli_dummyport; /*****************************************************************************/ static stlibrd_t *stli_brds[STL_MAXBRDS]; static int stli_shared; /* * Per board state flags. Used with the state field of the board struct. * Not really much here... All we need to do is keep track of whether * the board has been detected, and whether it is actually running a slave * or not. */ #define BST_FOUND 0x1 #define BST_STARTED 0x2 /* * Define the set of port state flags. These are marked for internal * state purposes only, usually to do with the state of communications * with the slave. Most of them need to be updated atomically, so always * use the bit setting operations (unless protected by cli/sti). */ #define ST_INITIALIZING 1 #define ST_OPENING 2 #define ST_CLOSING 3 #define ST_CMDING 4 #define ST_TXBUSY 5 #define ST_RXING 6 #define ST_DOFLUSHRX 7 #define ST_DOFLUSHTX 8 #define ST_DOSIGS 9 #define ST_RXSTOP 10 #define ST_GETSIGS 11 /* * Define an array of board names as printable strings. Handy for * referencing boards when printing trace and stuff. */ static char *stli_brdnames[] = { "Unknown", "Stallion", "Brumby", "ONboard-MC", "ONboard", "Brumby", "Brumby", "ONboard-EI", (char *) NULL, "ONboard", "ONboard-MC", "ONboard-MC", (char *) NULL, (char *) NULL, (char *) NULL, (char *) NULL, (char *) NULL, (char *) NULL, (char *) NULL, (char *) NULL, "EasyIO", "EC8/32-AT", "EC8/32-MC", "EC8/64-AT", "EC8/64-EI", "EC8/64-MC", "EC8/32-PCI", "EC8/64-PCI", "EasyIO-PCI", "EC/RA-PCI", }; /*****************************************************************************/ #ifdef MODULE /* * Define some string labels for arguments passed from the module * load line. These allow for easy board definitions, and easy * modification of the io, memory and irq resoucres. */ static char *board0[8]; static char *board1[8]; static char *board2[8]; static char *board3[8]; static char **stli_brdsp[] = { (char **) &board0, (char **) &board1, (char **) &board2, (char **) &board3 }; /* * Define a set of common board names, and types. This is used to * parse any module arguments. */ typedef struct stlibrdtype { char *name; int type; } stlibrdtype_t; static stlibrdtype_t stli_brdstr[] = { { "stallion", BRD_STALLION }, { "1", BRD_STALLION }, { "brumby", BRD_BRUMBY }, { "brumby4", BRD_BRUMBY }, { "brumby/4", BRD_BRUMBY }, { "brumby-4", BRD_BRUMBY }, { "brumby8", BRD_BRUMBY }, { "brumby/8", BRD_BRUMBY }, { "brumby-8", BRD_BRUMBY }, { "brumby16", BRD_BRUMBY }, { "brumby/16", BRD_BRUMBY }, { "brumby-16", BRD_BRUMBY }, { "2", BRD_BRUMBY }, { "onboard2", BRD_ONBOARD2 }, { "onboard-2", BRD_ONBOARD2 }, { "onboard/2", BRD_ONBOARD2 }, { "onboard-mc", BRD_ONBOARD2 }, { "onboard/mc", BRD_ONBOARD2 }, { "onboard-mca", BRD_ONBOARD2 }, { "onboard/mca", BRD_ONBOARD2 }, { "3", BRD_ONBOARD2 }, { "onboard", BRD_ONBOARD }, { "onboardat", BRD_ONBOARD }, { "4", BRD_ONBOARD }, { "onboarde", BRD_ONBOARDE }, { "onboard-e", BRD_ONBOARDE }, { "onboard/e", BRD_ONBOARDE }, { "onboard-ei", BRD_ONBOARDE }, { "onboard/ei", BRD_ONBOARDE }, { "7", BRD_ONBOARDE }, { "ecp", BRD_ECP }, { "ecpat", BRD_ECP }, { "ec8/64", BRD_ECP }, { "ec8/64-at", BRD_ECP }, { "ec8/64-isa", BRD_ECP }, { "23", BRD_ECP }, { "ecpe", BRD_ECPE }, { "ecpei", BRD_ECPE }, { "ec8/64-e", BRD_ECPE }, { "ec8/64-ei", BRD_ECPE }, { "24", BRD_ECPE }, { "ecpmc", BRD_ECPMC }, { "ec8/64-mc", BRD_ECPMC }, { "ec8/64-mca", BRD_ECPMC }, { "25", BRD_ECPMC }, { "ecppci", BRD_ECPPCI }, { "ec/ra", BRD_ECPPCI }, { "ec/ra-pc", BRD_ECPPCI }, { "ec/ra-pci", BRD_ECPPCI }, { "29", BRD_ECPPCI }, }; /* * Define the module agruments. */ MODULE_AUTHOR("Greg Ungerer"); MODULE_DESCRIPTION("Stallion Intelligent Multiport Serial Driver"); MODULE_LICENSE("GPL"); MODULE_PARM(board0, "1-3s"); MODULE_PARM_DESC(board0, "Board 0 config -> name[,ioaddr[,memaddr]"); MODULE_PARM(board1, "1-3s"); MODULE_PARM_DESC(board1, "Board 1 config -> name[,ioaddr[,memaddr]"); MODULE_PARM(board2, "1-3s"); MODULE_PARM_DESC(board2, "Board 2 config -> name[,ioaddr[,memaddr]"); MODULE_PARM(board3, "1-3s"); MODULE_PARM_DESC(board3, "Board 3 config -> name[,ioaddr[,memaddr]"); #endif /* * Set up a default memory address table for EISA board probing. * The default addresses are all bellow 1Mbyte, which has to be the * case anyway. They should be safe, since we only read values from * them, and interrupts are disabled while we do it. If the higher * memory support is compiled in then we also try probing around * the 1Gb, 2Gb and 3Gb areas as well... */ static unsigned long stli_eisamemprobeaddrs[] = { 0xc0000, 0xd0000, 0xe0000, 0xf0000, 0x80000000, 0x80010000, 0x80020000, 0x80030000, 0x40000000, 0x40010000, 0x40020000, 0x40030000, 0xc0000000, 0xc0010000, 0xc0020000, 0xc0030000, 0xff000000, 0xff010000, 0xff020000, 0xff030000, }; static int stli_eisamempsize = sizeof(stli_eisamemprobeaddrs) / sizeof(unsigned long); int stli_eisaprobe = STLI_EISAPROBE; /* * Define the Stallion PCI vendor and device IDs. */ #ifdef CONFIG_PCI #ifndef PCI_VENDOR_ID_STALLION #define PCI_VENDOR_ID_STALLION 0x124d #endif #ifndef PCI_DEVICE_ID_ECRA #define PCI_DEVICE_ID_ECRA 0x0004 #endif #endif static struct pci_device_id istallion_pci_tbl[] = { { PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECRA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, { 0 } }; MODULE_DEVICE_TABLE(pci, istallion_pci_tbl); /*****************************************************************************/ /* * Hardware configuration info for ECP boards. These defines apply * to the directly accessible io ports of the ECP. There is a set of * defines for each ECP board type, ISA, EISA, MCA and PCI. */ #define ECP_IOSIZE 4 #define ECP_MEMSIZE (128 * 1024) #define ECP_PCIMEMSIZE (256 * 1024) #define ECP_ATPAGESIZE (4 * 1024) #define ECP_MCPAGESIZE (4 * 1024) #define ECP_EIPAGESIZE (64 * 1024) #define ECP_PCIPAGESIZE (64 * 1024) #define STL_EISAID 0x8c4e /* * Important defines for the ISA class of ECP board. */ #define ECP_ATIREG 0 #define ECP_ATCONFR 1 #define ECP_ATMEMAR 2 #define ECP_ATMEMPR 3 #define ECP_ATSTOP 0x1 #define ECP_ATINTENAB 0x10 #define ECP_ATENABLE 0x20 #define ECP_ATDISABLE 0x00 #define ECP_ATADDRMASK 0x3f000 #define ECP_ATADDRSHFT 12 /* * Important defines for the EISA class of ECP board. */ #define ECP_EIIREG 0 #define ECP_EIMEMARL 1 #define ECP_EICONFR 2 #define ECP_EIMEMARH 3 #define ECP_EIENABLE 0x1 #define ECP_EIDISABLE 0x0 #define ECP_EISTOP 0x4 #define ECP_EIEDGE 0x00 #define ECP_EILEVEL 0x80 #define ECP_EIADDRMASKL 0x00ff0000 #define ECP_EIADDRSHFTL 16 #define ECP_EIADDRMASKH 0xff000000 #define ECP_EIADDRSHFTH 24 #define ECP_EIBRDENAB 0xc84 #define ECP_EISAID 0x4 /* * Important defines for the Micro-channel class of ECP board. * (It has a lot in common with the ISA boards.) */ #define ECP_MCIREG 0 #define ECP_MCCONFR 1 #define ECP_MCSTOP 0x20 #define ECP_MCENABLE 0x80 #define ECP_MCDISABLE 0x00 /* * Important defines for the PCI class of ECP board. * (It has a lot in common with the other ECP boards.) */ #define ECP_PCIIREG 0 #define ECP_PCICONFR 1 #define ECP_PCISTOP 0x01 /* * Hardware configuration info for ONboard and Brumby boards. These * defines apply to the directly accessible io ports of these boards. */ #define ONB_IOSIZE 16 #define ONB_MEMSIZE (64 * 1024) #define ONB_ATPAGESIZE (64 * 1024) #define ONB_MCPAGESIZE (64 * 1024) #define ONB_EIMEMSIZE (128 * 1024) #define ONB_EIPAGESIZE (64 * 1024) /* * Important defines for the ISA class of ONboard board. */ #define ONB_ATIREG 0 #define ONB_ATMEMAR 1 #define ONB_ATCONFR 2 #define ONB_ATSTOP 0x4 #define ONB_ATENABLE 0x01 #define ONB_ATDISABLE 0x00 #define ONB_ATADDRMASK 0xff0000 #define ONB_ATADDRSHFT 16 #define ONB_MEMENABLO 0 #define ONB_MEMENABHI 0x02 /* * Important defines for the EISA class of ONboard board. */ #define ONB_EIIREG 0 #define ONB_EIMEMARL 1 #define ONB_EICONFR 2 #define ONB_EIMEMARH 3 #define ONB_EIENABLE 0x1 #define ONB_EIDISABLE 0x0 #define ONB_EISTOP 0x4 #define ONB_EIEDGE 0x00 #define ONB_EILEVEL 0x80 #define ONB_EIADDRMASKL 0x00ff0000 #define ONB_EIADDRSHFTL 16 #define ONB_EIADDRMASKH 0xff000000 #define ONB_EIADDRSHFTH 24 #define ONB_EIBRDENAB 0xc84 #define ONB_EISAID 0x1 /* * Important defines for the Brumby boards. They are pretty simple, * there is not much that is programmably configurable. */ #define BBY_IOSIZE 16 #define BBY_MEMSIZE (64 * 1024) #define BBY_PAGESIZE (16 * 1024) #define BBY_ATIREG 0 #define BBY_ATCONFR 1 #define BBY_ATSTOP 0x4 /* * Important defines for the Stallion boards. They are pretty simple, * there is not much that is programmably configurable. */ #define STAL_IOSIZE 16 #define STAL_MEMSIZE (64 * 1024) #define STAL_PAGESIZE (64 * 1024) /* * Define the set of status register values for EasyConnection panels. * The signature will return with the status value for each panel. From * this we can determine what is attached to the board - before we have * actually down loaded any code to it. */ #define ECH_PNLSTATUS 2 #define ECH_PNL16PORT 0x20 #define ECH_PNLIDMASK 0x07 #define ECH_PNLXPID 0x40 #define ECH_PNLINTRPEND 0x80 /* * Define some macros to do things to the board. Even those these boards * are somewhat related there is often significantly different ways of * doing some operation on it (like enable, paging, reset, etc). So each * board class has a set of functions which do the commonly required * operations. The macros below basically just call these functions, * generally checking for a NULL function - which means that the board * needs nothing done to it to achieve this operation! */ #define EBRDINIT(brdp) \ if (brdp->init != NULL) \ (* brdp->init)(brdp) #define EBRDENABLE(brdp) \ if (brdp->enable != NULL) \ (* brdp->enable)(brdp); #define EBRDDISABLE(brdp) \ if (brdp->disable != NULL) \ (* brdp->disable)(brdp); #define EBRDINTR(brdp) \ if (brdp->intr != NULL) \ (* brdp->intr)(brdp); #define EBRDRESET(brdp) \ if (brdp->reset != NULL) \ (* brdp->reset)(brdp); #define EBRDGETMEMPTR(brdp,offset) \ (* brdp->getmemptr)(brdp, offset, __LINE__) /* * Define the maximal baud rate, and the default baud base for ports. */ #define STL_MAXBAUD 460800 #define STL_BAUDBASE 115200 #define STL_CLOSEDELAY (5 * HZ / 10) /*****************************************************************************/ /* * Define macros to extract a brd or port number from a minor number. */ #define MINOR2BRD(min) (((min) & 0xc0) >> 6) #define MINOR2PORT(min) ((min) & 0x3f) /* * Define a baud rate table that converts termios baud rate selector * into the actual baud rate value. All baud rate calculations are based * on the actual baud rate required. */ static unsigned int stli_baudrates[] = { 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }; /*****************************************************************************/ /* * Define some handy local macros... */ #undef MIN #define MIN(a,b) (((a) <= (b)) ? (a) : (b)) #undef TOLOWER #define TOLOWER(x) ((((x) >= 'A') && ((x) <= 'Z')) ? ((x) + 0x20) : (x)) /*****************************************************************************/ /* * Prototype all functions in this driver! */ #ifdef MODULE int init_module(void); void cleanup_module(void); static void stli_argbrds(void); static int stli_parsebrd(stlconf_t *confp, char **argp); static unsigned long stli_atol(char *str); #endif int stli_init(void); static int stli_open(struct tty_struct *tty, struct file *filp); static void stli_close(struct tty_struct *tty, struct file *filp); static int stli_write(struct tty_struct *tty, int from_user, const unsigned char *buf, int count); static void stli_putchar(struct tty_struct *tty, unsigned char ch); static void stli_flushchars(struct tty_struct *tty); static int stli_writeroom(struct tty_struct *tty); static int stli_charsinbuffer(struct tty_struct *tty); static int stli_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg); static void stli_settermios(struct tty_struct *tty, struct termios *old); static void stli_throttle(struct tty_struct *tty); static void stli_unthrottle(struct tty_struct *tty); static void stli_stop(struct tty_struct *tty); static void stli_start(struct tty_struct *tty); static void stli_flushbuffer(struct tty_struct *tty); static void stli_breakctl(struct tty_struct *tty, int state); static void stli_waituntilsent(struct tty_struct *tty, int timeout); static void stli_sendxchar(struct tty_struct *tty, char ch); static void stli_hangup(struct tty_struct *tty); static int stli_portinfo(stlibrd_t *brdp, stliport_t *portp, int portnr, char *pos); static int stli_brdinit(stlibrd_t *brdp); static int stli_startbrd(stlibrd_t *brdp); static ssize_t stli_memread(struct file *fp, char *buf, size_t count, loff_t *offp); static ssize_t stli_memwrite(struct file *fp, const char *buf, size_t count, loff_t *offp); static int stli_memioctl(struct inode *ip, struct file *fp, unsigned int cmd, unsigned long arg); static void stli_brdpoll(stlibrd_t *brdp, volatile cdkhdr_t *hdrp); static void stli_poll(unsigned long arg); static int stli_hostcmd(stlibrd_t *brdp, stliport_t *portp); static int stli_initopen(stlibrd_t *brdp, stliport_t *portp); static int stli_rawopen(stlibrd_t *brdp, stliport_t *portp, unsigned long arg, int wait); static int stli_rawclose(stlibrd_t *brdp, stliport_t *portp, unsigned long arg, int wait); static int stli_waitcarrier(stlibrd_t *brdp, stliport_t *portp, struct file *filp); static void stli_dohangup(void *arg); static void stli_delay(int len); static int stli_setport(stliport_t *portp); static int stli_cmdwait(stlibrd_t *brdp, stliport_t *portp, unsigned long cmd, void *arg, int size, int copyback); static void stli_sendcmd(stlibrd_t *brdp, stliport_t *portp, unsigned long cmd, void *arg, int size, int copyback); static void stli_dodelaycmd(stliport_t *portp, volatile cdkctrl_t *cp); static void stli_mkasyport(stliport_t *portp, asyport_t *pp, struct termios *tiosp); static void stli_mkasysigs(asysigs_t *sp, int dtr, int rts); static long stli_mktiocm(unsigned long sigvalue); static void stli_read(stlibrd_t *brdp, stliport_t *portp); static void stli_getserial(stliport_t *portp, struct serial_struct *sp); static int stli_setserial(stliport_t *portp, struct serial_struct *sp); static int stli_getbrdstats(combrd_t *bp); static int stli_getportstats(stliport_t *portp, comstats_t *cp); static int stli_portcmdstats(stliport_t *portp); static int stli_clrportstats(stliport_t *portp, comstats_t *cp); static int stli_getportstruct(unsigned long arg); static int stli_getbrdstruct(unsigned long arg); static void *stli_memalloc(int len); static stlibrd_t *stli_allocbrd(void); static void stli_ecpinit(stlibrd_t *brdp); static void stli_ecpenable(stlibrd_t *brdp); static void stli_ecpdisable(stlibrd_t *brdp); static char *stli_ecpgetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_ecpreset(stlibrd_t *brdp); static void stli_ecpintr(stlibrd_t *brdp); static void stli_ecpeiinit(stlibrd_t *brdp); static void stli_ecpeienable(stlibrd_t *brdp); static void stli_ecpeidisable(stlibrd_t *brdp); static char *stli_ecpeigetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_ecpeireset(stlibrd_t *brdp); static void stli_ecpmcenable(stlibrd_t *brdp); static void stli_ecpmcdisable(stlibrd_t *brdp); static char *stli_ecpmcgetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_ecpmcreset(stlibrd_t *brdp); static void stli_ecppciinit(stlibrd_t *brdp); static char *stli_ecppcigetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_ecppcireset(stlibrd_t *brdp); static void stli_onbinit(stlibrd_t *brdp); static void stli_onbenable(stlibrd_t *brdp); static void stli_onbdisable(stlibrd_t *brdp); static char *stli_onbgetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_onbreset(stlibrd_t *brdp); static void stli_onbeinit(stlibrd_t *brdp); static void stli_onbeenable(stlibrd_t *brdp); static void stli_onbedisable(stlibrd_t *brdp); static char *stli_onbegetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_onbereset(stlibrd_t *brdp); static void stli_bbyinit(stlibrd_t *brdp); static char *stli_bbygetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_bbyreset(stlibrd_t *brdp); static void stli_stalinit(stlibrd_t *brdp); static char *stli_stalgetmemptr(stlibrd_t *brdp, unsigned long offset, int line); static void stli_stalreset(stlibrd_t *brdp); static stliport_t *stli_getport(int brdnr, int panelnr, int portnr); static inline int stli_initbrds(void); static inline int stli_initecp(stlibrd_t *brdp); static inline int stli_initonb(stlibrd_t *brdp); static inline int stli_findeisabrds(void); static inline int stli_eisamemprobe(stlibrd_t *brdp); static inline int stli_initports(stlibrd_t *brdp); static inline int stli_getbrdnr(void); #ifdef CONFIG_PCI static inline int stli_findpcibrds(void); static inline int stli_initpcibrd(int brdtype, struct pci_dev *devp); #endif /*****************************************************************************/ /* * Define the driver info for a user level shared memory device. This * device will work sort of like the /dev/kmem device - except that it * will give access to the shared memory on the Stallion intelligent * board. This is also a very useful debugging tool. */ static struct file_operations stli_fsiomem = { owner: THIS_MODULE, read: stli_memread, write: stli_memwrite, ioctl: stli_memioctl, }; /*****************************************************************************/ /* * Define a timer_list entry for our poll routine. The slave board * is polled every so often to see if anything needs doing. This is * much cheaper on host cpu than using interrupts. It turns out to * not increase character latency by much either... */ static struct timer_list stli_timerlist = { function: stli_poll }; static int stli_timeron; /* * Define the calculation for the timeout routine. */ #define STLI_TIMEOUT (jiffies + 1) /*****************************************************************************/ #ifdef MODULE /* * Loadable module initialization stuff. */ int init_module() { unsigned long flags; #if DEBUG printk("init_module()\n"); #endif save_flags(flags); cli(); stli_init(); restore_flags(flags); return(0); } /*****************************************************************************/ void cleanup_module() { stlibrd_t *brdp; stliport_t *portp; unsigned long flags; int i, j; #if DEBUG printk("cleanup_module()\n"); #endif printk(KERN_INFO "Unloading %s: version %s\n", stli_drvtitle, stli_drvversion); save_flags(flags); cli(); /* * Free up all allocated resources used by the ports. This includes * memory and interrupts. */ if (stli_timeron) { stli_timeron = 0; del_timer(&stli_timerlist); } i = tty_unregister_driver(&stli_serial); j = tty_unregister_driver(&stli_callout); if (i || j) { printk("STALLION: failed to un-register tty driver, " "errno=%d,%d\n", -i, -j); restore_flags(flags); return; } devfs_unregister (devfs_handle); if ((i = devfs_unregister_chrdev(STL_SIOMEMMAJOR, "staliomem"))) printk("STALLION: failed to un-register serial memory device, " "errno=%d\n", -i); if (stli_tmpwritebuf != (char *) NULL) kfree(stli_tmpwritebuf); if (stli_txcookbuf != (char *) NULL) kfree(stli_txcookbuf); for (i = 0; (i < stli_nrbrds); i++) { if ((brdp = stli_brds[i]) == (stlibrd_t *) NULL) continue; for (j = 0; (j < STL_MAXPORTS); j++) { portp = brdp->ports[j]; if (portp != (stliport_t *) NULL) { if (portp->tty != (struct tty_struct *) NULL) tty_hangup(portp->tty); kfree(portp); } } iounmap(brdp->membase); if (brdp->iosize > 0) release_region(brdp->iobase, brdp->iosize); kfree(brdp); stli_brds[i] = (stlibrd_t *) NULL; } restore_flags(flags); } /*****************************************************************************/ /* * Check for any arguments passed in on the module load command line. */ static void stli_argbrds() { stlconf_t conf; stlibrd_t *brdp; int nrargs, i; #if DEBUG printk("stli_argbrds()\n"); #endif nrargs = sizeof(stli_brdsp) / sizeof(char **); for (i = stli_nrbrds; (i < nrargs); i++) { memset(&conf, 0, sizeof(conf)); if (stli_parsebrd(&conf, stli_brdsp[i]) == 0) continue; if ((brdp = stli_allocbrd()) == (stlibrd_t *) NULL) continue; stli_nrbrds = i + 1; brdp->brdnr = i; brdp->brdtype = conf.brdtype; brdp->iobase = conf.ioaddr1; brdp->memaddr = conf.memaddr; stli_brdinit(brdp); } } /*****************************************************************************/ /* * Convert an ascii string number into an unsigned long. */ static unsigned long stli_atol(char *str) { unsigned long val; int base, c; char *sp; val = 0; sp = str; if ((*sp == '0') && (*(sp+1) == 'x')) { base = 16; sp += 2; } else if (*sp == '0') { base = 8; sp++; } else { base = 10; } for (; (*sp != 0); sp++) { c = (*sp > '9') ? (TOLOWER(*sp) - 'a' + 10) : (*sp - '0'); if ((c < 0) || (c >= base)) { printk("STALLION: invalid argument %s\n", str); val = 0; break; } val = (val * base) + c; } return(val); } /*****************************************************************************/ /* * Parse the supplied argument string, into the board conf struct. */ static int stli_parsebrd(stlconf_t *confp, char **argp) { char *sp; int nrbrdnames, i; #if DEBUG printk("stli_parsebrd(confp=%x,argp=%x)\n", (int) confp, (int) argp); #endif if ((argp[0] == (char *) NULL) || (*argp[0] == 0)) return(0); for (sp = argp[0], i = 0; ((*sp != 0) && (i < 25)); sp++, i++) *sp = TOLOWER(*sp); nrbrdnames = sizeof(stli_brdstr) / sizeof(stlibrdtype_t); for (i = 0; (i < nrbrdnames); i++) { if (strcmp(stli_brdstr[i].name, argp[0]) == 0) break; } if (i >= nrbrdnames) { printk("STALLION: unknown board name, %s?\n", argp[0]); return(0); } confp->brdtype = stli_brdstr[i].type; if ((argp[1] != (char *) NULL) && (*argp[1] != 0)) confp->ioaddr1 = stli_atol(argp[1]); if ((argp[2] != (char *) NULL) && (*argp[2] != 0)) confp->memaddr = stli_atol(argp[2]); return(1); } #endif /*****************************************************************************/ /* * Local driver kernel malloc routine. */ static void *stli_memalloc(int len) { return((void *) kmalloc(len, GFP_KERNEL)); } /*****************************************************************************/ static int stli_open(struct tty_struct *tty, struct file *filp) { stlibrd_t *brdp; stliport_t *portp; unsigned int minordev; int brdnr, portnr, rc; #if DEBUG printk("stli_open(tty=%x,filp=%x): device=%x\n", (int) tty, (int) filp, tty->device); #endif minordev = MINOR(tty->device); brdnr = MINOR2BRD(minordev); if (brdnr >= stli_nrbrds) return(-ENODEV); brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if ((brdp->state & BST_STARTED) == 0) return(-ENODEV); portnr = MINOR2PORT(minordev); if ((portnr < 0) || (portnr > brdp->nrports)) return(-ENODEV); portp = brdp->ports[portnr]; if (portp == (stliport_t *) NULL) return(-ENODEV); if (portp->devnr < 1) return(-ENODEV); MOD_INC_USE_COUNT; /* * Check if this port is in the middle of closing. If so then wait * until it is closed then return error status based on flag settings. * The sleep here does not need interrupt protection since the wakeup * for it is done with the same context. */ if (portp->flags & ASYNC_CLOSING) { interruptible_sleep_on(&portp->close_wait); if (portp->flags & ASYNC_HUP_NOTIFY) return(-EAGAIN); return(-ERESTARTSYS); } /* * On the first open of the device setup the port hardware, and * initialize the per port data structure. Since initializing the port * requires several commands to the board we will need to wait for any * other open that is already initializing the port. */ portp->tty = tty; tty->driver_data = portp; portp->refcount++; while (test_bit(ST_INITIALIZING, &portp->state)) { if (signal_pending(current)) return(-ERESTARTSYS); interruptible_sleep_on(&portp->raw_wait); } if ((portp->flags & ASYNC_INITIALIZED) == 0) { set_bit(ST_INITIALIZING, &portp->state); if ((rc = stli_initopen(brdp, portp)) >= 0) { portp->flags |= ASYNC_INITIALIZED; clear_bit(TTY_IO_ERROR, &tty->flags); } clear_bit(ST_INITIALIZING, &portp->state); wake_up_interruptible(&portp->raw_wait); if (rc < 0) return(rc); } /* * Check if this port is in the middle of closing. If so then wait * until it is closed then return error status, based on flag settings. * The sleep here does not need interrupt protection since the wakeup * for it is done with the same context. */ if (portp->flags & ASYNC_CLOSING) { interruptible_sleep_on(&portp->close_wait); if (portp->flags & ASYNC_HUP_NOTIFY) return(-EAGAIN); return(-ERESTARTSYS); } /* * Based on type of open being done check if it can overlap with any * previous opens still in effect. If we are a normal serial device * then also we might have to wait for carrier. */ if (tty->driver.subtype == STL_DRVTYPCALLOUT) { if (portp->flags & ASYNC_NORMAL_ACTIVE) return(-EBUSY); if (portp->flags & ASYNC_CALLOUT_ACTIVE) { if ((portp->flags & ASYNC_SESSION_LOCKOUT) && (portp->session != current->session)) return(-EBUSY); if ((portp->flags & ASYNC_PGRP_LOCKOUT) && (portp->pgrp != current->pgrp)) return(-EBUSY); } portp->flags |= ASYNC_CALLOUT_ACTIVE; } else { if (filp->f_flags & O_NONBLOCK) { if (portp->flags & ASYNC_CALLOUT_ACTIVE) return(-EBUSY); } else { if ((rc = stli_waitcarrier(brdp, portp, filp)) != 0) return(rc); } portp->flags |= ASYNC_NORMAL_ACTIVE; } if ((portp->refcount == 1) && (portp->flags & ASYNC_SPLIT_TERMIOS)) { if (tty->driver.subtype == STL_DRVTYPSERIAL) *tty->termios = portp->normaltermios; else *tty->termios = portp->callouttermios; stli_setport(portp); } portp->session = current->session; portp->pgrp = current->pgrp; return(0); } /*****************************************************************************/ static void stli_close(struct tty_struct *tty, struct file *filp) { stlibrd_t *brdp; stliport_t *portp; unsigned long flags; #if DEBUG printk("stli_close(tty=%x,filp=%x)\n", (int) tty, (int) filp); #endif portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; save_flags(flags); cli(); if (tty_hung_up_p(filp)) { MOD_DEC_USE_COUNT; restore_flags(flags); return; } if ((tty->count == 1) && (portp->refcount != 1)) portp->refcount = 1; if (portp->refcount-- > 1) { MOD_DEC_USE_COUNT; restore_flags(flags); return; } portp->flags |= ASYNC_CLOSING; if (portp->flags & ASYNC_NORMAL_ACTIVE) portp->normaltermios = *tty->termios; if (portp->flags & ASYNC_CALLOUT_ACTIVE) portp->callouttermios = *tty->termios; /* * May want to wait for data to drain before closing. The BUSY flag * keeps track of whether we are still transmitting or not. It is * updated by messages from the slave - indicating when all chars * really have drained. */ if (tty == stli_txcooktty) stli_flushchars(tty); tty->closing = 1; if (portp->closing_wait != ASYNC_CLOSING_WAIT_NONE) tty_wait_until_sent(tty, portp->closing_wait); portp->flags &= ~ASYNC_INITIALIZED; brdp = stli_brds[portp->brdnr]; stli_rawclose(brdp, portp, 0, 0); if (tty->termios->c_cflag & HUPCL) { stli_mkasysigs(&portp->asig, 0, 0); if (test_bit(ST_CMDING, &portp->state)) set_bit(ST_DOSIGS, &portp->state); else stli_sendcmd(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0); } clear_bit(ST_TXBUSY, &portp->state); clear_bit(ST_RXSTOP, &portp->state); set_bit(TTY_IO_ERROR, &tty->flags); if (tty->ldisc.flush_buffer) (tty->ldisc.flush_buffer)(tty); set_bit(ST_DOFLUSHRX, &portp->state); stli_flushbuffer(tty); tty->closing = 0; portp->tty = (struct tty_struct *) NULL; if (portp->openwaitcnt) { if (portp->close_delay) stli_delay(portp->close_delay); wake_up_interruptible(&portp->open_wait); } portp->flags &= ~(ASYNC_CALLOUT_ACTIVE | ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING); wake_up_interruptible(&portp->close_wait); MOD_DEC_USE_COUNT; restore_flags(flags); } /*****************************************************************************/ /* * Carry out first open operations on a port. This involves a number of * commands to be sent to the slave. We need to open the port, set the * notification events, set the initial port settings, get and set the * initial signal values. We sleep and wait in between each one. But * this still all happens pretty quickly. */ static int stli_initopen(stlibrd_t *brdp, stliport_t *portp) { struct tty_struct *tty; asynotify_t nt; asyport_t aport; int rc; #if DEBUG printk("stli_initopen(brdp=%x,portp=%x)\n", (int) brdp, (int) portp); #endif if ((rc = stli_rawopen(brdp, portp, 0, 1)) < 0) return(rc); memset(&nt, 0, sizeof(asynotify_t)); nt.data = (DT_TXLOW | DT_TXEMPTY | DT_RXBUSY | DT_RXBREAK); nt.signal = SG_DCD; if ((rc = stli_cmdwait(brdp, portp, A_SETNOTIFY, &nt, sizeof(asynotify_t), 0)) < 0) return(rc); tty = portp->tty; if (tty == (struct tty_struct *) NULL) return(-ENODEV); stli_mkasyport(portp, &aport, tty->termios); if ((rc = stli_cmdwait(brdp, portp, A_SETPORT, &aport, sizeof(asyport_t), 0)) < 0) return(rc); set_bit(ST_GETSIGS, &portp->state); if ((rc = stli_cmdwait(brdp, portp, A_GETSIGNALS, &portp->asig, sizeof(asysigs_t), 1)) < 0) return(rc); if (test_and_clear_bit(ST_GETSIGS, &portp->state)) portp->sigs = stli_mktiocm(portp->asig.sigvalue); stli_mkasysigs(&portp->asig, 1, 1); if ((rc = stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0)) < 0) return(rc); return(0); } /*****************************************************************************/ /* * Send an open message to the slave. This will sleep waiting for the * acknowledgement, so must have user context. We need to co-ordinate * with close events here, since we don't want open and close events * to overlap. */ static int stli_rawopen(stlibrd_t *brdp, stliport_t *portp, unsigned long arg, int wait) { volatile cdkhdr_t *hdrp; volatile cdkctrl_t *cp; volatile unsigned char *bits; unsigned long flags; int rc; #if DEBUG printk("stli_rawopen(brdp=%x,portp=%x,arg=%x,wait=%d)\n", (int) brdp, (int) portp, (int) arg, wait); #endif /* * Send a message to the slave to open this port. */ save_flags(flags); cli(); /* * Slave is already closing this port. This can happen if a hangup * occurs on this port. So we must wait until it is complete. The * order of opens and closes may not be preserved across shared * memory, so we must wait until it is complete. */ while (test_bit(ST_CLOSING, &portp->state)) { if (signal_pending(current)) { restore_flags(flags); return(-ERESTARTSYS); } interruptible_sleep_on(&portp->raw_wait); } /* * Everything is ready now, so write the open message into shared * memory. Once the message is in set the service bits to say that * this port wants service. */ EBRDENABLE(brdp); cp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->ctrl; cp->openarg = arg; cp->open = 1; hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); bits = ((volatile unsigned char *) hdrp) + brdp->slaveoffset + portp->portidx; *bits |= portp->portbit; EBRDDISABLE(brdp); if (wait == 0) { restore_flags(flags); return(0); } /* * Slave is in action, so now we must wait for the open acknowledgment * to come back. */ rc = 0; set_bit(ST_OPENING, &portp->state); while (test_bit(ST_OPENING, &portp->state)) { if (signal_pending(current)) { rc = -ERESTARTSYS; break; } interruptible_sleep_on(&portp->raw_wait); } restore_flags(flags); if ((rc == 0) && (portp->rc != 0)) rc = -EIO; return(rc); } /*****************************************************************************/ /* * Send a close message to the slave. Normally this will sleep waiting * for the acknowledgement, but if wait parameter is 0 it will not. If * wait is true then must have user context (to sleep). */ static int stli_rawclose(stlibrd_t *brdp, stliport_t *portp, unsigned long arg, int wait) { volatile cdkhdr_t *hdrp; volatile cdkctrl_t *cp; volatile unsigned char *bits; unsigned long flags; int rc; #if DEBUG printk("stli_rawclose(brdp=%x,portp=%x,arg=%x,wait=%d)\n", (int) brdp, (int) portp, (int) arg, wait); #endif save_flags(flags); cli(); /* * Slave is already closing this port. This can happen if a hangup * occurs on this port. */ if (wait) { while (test_bit(ST_CLOSING, &portp->state)) { if (signal_pending(current)) { restore_flags(flags); return(-ERESTARTSYS); } interruptible_sleep_on(&portp->raw_wait); } } /* * Write the close command into shared memory. */ EBRDENABLE(brdp); cp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->ctrl; cp->closearg = arg; cp->close = 1; hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); bits = ((volatile unsigned char *) hdrp) + brdp->slaveoffset + portp->portidx; *bits |= portp->portbit; EBRDDISABLE(brdp); set_bit(ST_CLOSING, &portp->state); if (wait == 0) { restore_flags(flags); return(0); } /* * Slave is in action, so now we must wait for the open acknowledgment * to come back. */ rc = 0; while (test_bit(ST_CLOSING, &portp->state)) { if (signal_pending(current)) { rc = -ERESTARTSYS; break; } interruptible_sleep_on(&portp->raw_wait); } restore_flags(flags); if ((rc == 0) && (portp->rc != 0)) rc = -EIO; return(rc); } /*****************************************************************************/ /* * Send a command to the slave and wait for the response. This must * have user context (it sleeps). This routine is generic in that it * can send any type of command. Its purpose is to wait for that command * to complete (as opposed to initiating the command then returning). */ static int stli_cmdwait(stlibrd_t *brdp, stliport_t *portp, unsigned long cmd, void *arg, int size, int copyback) { unsigned long flags; #if DEBUG printk("stli_cmdwait(brdp=%x,portp=%x,cmd=%x,arg=%x,size=%d," "copyback=%d)\n", (int) brdp, (int) portp, (int) cmd, (int) arg, size, copyback); #endif save_flags(flags); cli(); while (test_bit(ST_CMDING, &portp->state)) { if (signal_pending(current)) { restore_flags(flags); return(-ERESTARTSYS); } interruptible_sleep_on(&portp->raw_wait); } stli_sendcmd(brdp, portp, cmd, arg, size, copyback); while (test_bit(ST_CMDING, &portp->state)) { if (signal_pending(current)) { restore_flags(flags); return(-ERESTARTSYS); } interruptible_sleep_on(&portp->raw_wait); } restore_flags(flags); if (portp->rc != 0) return(-EIO); return(0); } /*****************************************************************************/ /* * Send the termios settings for this port to the slave. This sleeps * waiting for the command to complete - so must have user context. */ static int stli_setport(stliport_t *portp) { stlibrd_t *brdp; asyport_t aport; #if DEBUG printk("stli_setport(portp=%x)\n", (int) portp); #endif if (portp == (stliport_t *) NULL) return(-ENODEV); if (portp->tty == (struct tty_struct *) NULL) return(-ENODEV); if ((portp->brdnr < 0) && (portp->brdnr >= stli_nrbrds)) return(-ENODEV); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); stli_mkasyport(portp, &aport, portp->tty->termios); return(stli_cmdwait(brdp, portp, A_SETPORT, &aport, sizeof(asyport_t), 0)); } /*****************************************************************************/ /* * Wait for a specified delay period, this is not a busy-loop. It will * give up the processor while waiting. Unfortunately this has some * rather intimate knowledge of the process management stuff. */ static void stli_delay(int len) { #if DEBUG printk("stli_delay(len=%d)\n", len); #endif if (len > 0) { set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(len); set_current_state(TASK_RUNNING); } } /*****************************************************************************/ /* * Possibly need to wait for carrier (DCD signal) to come high. Say * maybe because if we are clocal then we don't need to wait... */ static int stli_waitcarrier(stlibrd_t *brdp, stliport_t *portp, struct file *filp) { unsigned long flags; int rc, doclocal; #if DEBUG printk("stli_waitcarrier(brdp=%x,portp=%x,filp=%x)\n", (int) brdp, (int) portp, (int) filp); #endif rc = 0; doclocal = 0; if (portp->flags & ASYNC_CALLOUT_ACTIVE) { if (portp->normaltermios.c_cflag & CLOCAL) doclocal++; } else { if (portp->tty->termios->c_cflag & CLOCAL) doclocal++; } save_flags(flags); cli(); portp->openwaitcnt++; if (! tty_hung_up_p(filp)) portp->refcount--; for (;;) { if ((portp->flags & ASYNC_CALLOUT_ACTIVE) == 0) { stli_mkasysigs(&portp->asig, 1, 1); if ((rc = stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0)) < 0) break; } if (tty_hung_up_p(filp) || ((portp->flags & ASYNC_INITIALIZED) == 0)) { if (portp->flags & ASYNC_HUP_NOTIFY) rc = -EBUSY; else rc = -ERESTARTSYS; break; } if (((portp->flags & ASYNC_CALLOUT_ACTIVE) == 0) && ((portp->flags & ASYNC_CLOSING) == 0) && (doclocal || (portp->sigs & TIOCM_CD))) { break; } if (signal_pending(current)) { rc = -ERESTARTSYS; break; } interruptible_sleep_on(&portp->open_wait); } if (! tty_hung_up_p(filp)) portp->refcount++; portp->openwaitcnt--; restore_flags(flags); return(rc); } /*****************************************************************************/ /* * Write routine. Take the data and put it in the shared memory ring * queue. If port is not already sending chars then need to mark the * service bits for this port. */ static int stli_write(struct tty_struct *tty, int from_user, const unsigned char *buf, int count) { volatile cdkasy_t *ap; volatile cdkhdr_t *hdrp; volatile unsigned char *bits; unsigned char *shbuf, *chbuf; stliport_t *portp; stlibrd_t *brdp; unsigned int len, stlen, head, tail, size; unsigned long flags; #if DEBUG printk("stli_write(tty=%x,from_user=%d,buf=%x,count=%d)\n", (int) tty, from_user, (int) buf, count); #endif if ((tty == (struct tty_struct *) NULL) || (stli_tmpwritebuf == (char *) NULL)) return(0); if (tty == stli_txcooktty) stli_flushchars(tty); portp = tty->driver_data; if (portp == (stliport_t *) NULL) return(0); if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return(0); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(0); chbuf = (unsigned char *) buf; /* * If copying direct from user space we need to be able to handle page * faults while we are copying. To do this copy as much as we can now * into a kernel buffer. From there we copy it into shared memory. The * big problem is that we do not want shared memory enabled when we are * sleeping (other boards may be serviced while asleep). Something else * to note here is the reading of the tail twice. Since the boards * shared memory can be on an 8-bit bus then we need to be very careful * reading 16 bit quantities - since both the board (slave) and host * could be writing and reading at the same time. */ if (from_user) { save_flags(flags); cli(); EBRDENABLE(brdp); ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); head = (unsigned int) ap->txq.head; tail = (unsigned int) ap->txq.tail; if (tail != ((unsigned int) ap->txq.tail)) tail = (unsigned int) ap->txq.tail; len = (head >= tail) ? (portp->txsize - (head - tail) - 1) : (tail - head - 1); count = MIN(len, count); EBRDDISABLE(brdp); restore_flags(flags); down(&stli_tmpwritesem); copy_from_user(stli_tmpwritebuf, chbuf, count); chbuf = &stli_tmpwritebuf[0]; } /* * All data is now local, shove as much as possible into shared memory. */ save_flags(flags); cli(); EBRDENABLE(brdp); ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); head = (unsigned int) ap->txq.head; tail = (unsigned int) ap->txq.tail; if (tail != ((unsigned int) ap->txq.tail)) tail = (unsigned int) ap->txq.tail; size = portp->txsize; if (head >= tail) { len = size - (head - tail) - 1; stlen = size - head; } else { len = tail - head - 1; stlen = len; } len = MIN(len, count); count = 0; shbuf = (char *) EBRDGETMEMPTR(brdp, portp->txoffset); while (len > 0) { stlen = MIN(len, stlen); memcpy((shbuf + head), chbuf, stlen); chbuf += stlen; len -= stlen; count += stlen; head += stlen; if (head >= size) { head = 0; stlen = tail; } } ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); ap->txq.head = head; if (test_bit(ST_TXBUSY, &portp->state)) { if (ap->changed.data & DT_TXEMPTY) ap->changed.data &= ~DT_TXEMPTY; } hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); bits = ((volatile unsigned char *) hdrp) + brdp->slaveoffset + portp->portidx; *bits |= portp->portbit; set_bit(ST_TXBUSY, &portp->state); EBRDDISABLE(brdp); if (from_user) up(&stli_tmpwritesem); restore_flags(flags); return(count); } /*****************************************************************************/ /* * Output a single character. We put it into a temporary local buffer * (for speed) then write out that buffer when the flushchars routine * is called. There is a safety catch here so that if some other port * writes chars before the current buffer has been, then we write them * first them do the new ports. */ static void stli_putchar(struct tty_struct *tty, unsigned char ch) { #if DEBUG printk("stli_putchar(tty=%x,ch=%x)\n", (int) tty, (int) ch); #endif if (tty == (struct tty_struct *) NULL) return; if (tty != stli_txcooktty) { if (stli_txcooktty != (struct tty_struct *) NULL) stli_flushchars(stli_txcooktty); stli_txcooktty = tty; } stli_txcookbuf[stli_txcooksize++] = ch; } /*****************************************************************************/ /* * Transfer characters from the local TX cooking buffer to the board. * We sort of ignore the tty that gets passed in here. We rely on the * info stored with the TX cook buffer to tell us which port to flush * the data on. In any case we clean out the TX cook buffer, for re-use * by someone else. */ static void stli_flushchars(struct tty_struct *tty) { volatile cdkhdr_t *hdrp; volatile unsigned char *bits; volatile cdkasy_t *ap; struct tty_struct *cooktty; stliport_t *portp; stlibrd_t *brdp; unsigned int len, stlen, head, tail, size, count, cooksize; unsigned char *buf, *shbuf; unsigned long flags; #if DEBUG printk("stli_flushchars(tty=%x)\n", (int) tty); #endif cooksize = stli_txcooksize; cooktty = stli_txcooktty; stli_txcooksize = 0; stli_txcookrealsize = 0; stli_txcooktty = (struct tty_struct *) NULL; if (tty == (struct tty_struct *) NULL) return; if (cooktty == (struct tty_struct *) NULL) return; if (tty != cooktty) tty = cooktty; if (cooksize == 0) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; save_flags(flags); cli(); EBRDENABLE(brdp); ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); head = (unsigned int) ap->txq.head; tail = (unsigned int) ap->txq.tail; if (tail != ((unsigned int) ap->txq.tail)) tail = (unsigned int) ap->txq.tail; size = portp->txsize; if (head >= tail) { len = size - (head - tail) - 1; stlen = size - head; } else { len = tail - head - 1; stlen = len; } len = MIN(len, cooksize); count = 0; shbuf = (char *) EBRDGETMEMPTR(brdp, portp->txoffset); buf = stli_txcookbuf; while (len > 0) { stlen = MIN(len, stlen); memcpy((shbuf + head), buf, stlen); buf += stlen; len -= stlen; count += stlen; head += stlen; if (head >= size) { head = 0; stlen = tail; } } ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); ap->txq.head = head; if (test_bit(ST_TXBUSY, &portp->state)) { if (ap->changed.data & DT_TXEMPTY) ap->changed.data &= ~DT_TXEMPTY; } hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); bits = ((volatile unsigned char *) hdrp) + brdp->slaveoffset + portp->portidx; *bits |= portp->portbit; set_bit(ST_TXBUSY, &portp->state); EBRDDISABLE(brdp); restore_flags(flags); } /*****************************************************************************/ static int stli_writeroom(struct tty_struct *tty) { volatile cdkasyrq_t *rp; stliport_t *portp; stlibrd_t *brdp; unsigned int head, tail, len; unsigned long flags; #if DEBUG printk("stli_writeroom(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return(0); if (tty == stli_txcooktty) { if (stli_txcookrealsize != 0) { len = stli_txcookrealsize - stli_txcooksize; return(len); } } portp = tty->driver_data; if (portp == (stliport_t *) NULL) return(0); if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return(0); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(0); save_flags(flags); cli(); EBRDENABLE(brdp); rp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->txq; head = (unsigned int) rp->head; tail = (unsigned int) rp->tail; if (tail != ((unsigned int) rp->tail)) tail = (unsigned int) rp->tail; len = (head >= tail) ? (portp->txsize - (head - tail)) : (tail - head); len--; EBRDDISABLE(brdp); restore_flags(flags); if (tty == stli_txcooktty) { stli_txcookrealsize = len; len -= stli_txcooksize; } return(len); } /*****************************************************************************/ /* * Return the number of characters in the transmit buffer. Normally we * will return the number of chars in the shared memory ring queue. * We need to kludge around the case where the shared memory buffer is * empty but not all characters have drained yet, for this case just * return that there is 1 character in the buffer! */ static int stli_charsinbuffer(struct tty_struct *tty) { volatile cdkasyrq_t *rp; stliport_t *portp; stlibrd_t *brdp; unsigned int head, tail, len; unsigned long flags; #if DEBUG printk("stli_charsinbuffer(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return(0); if (tty == stli_txcooktty) stli_flushchars(tty); portp = tty->driver_data; if (portp == (stliport_t *) NULL) return(0); if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return(0); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(0); save_flags(flags); cli(); EBRDENABLE(brdp); rp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->txq; head = (unsigned int) rp->head; tail = (unsigned int) rp->tail; if (tail != ((unsigned int) rp->tail)) tail = (unsigned int) rp->tail; len = (head >= tail) ? (head - tail) : (portp->txsize - (tail - head)); if ((len == 0) && test_bit(ST_TXBUSY, &portp->state)) len = 1; EBRDDISABLE(brdp); restore_flags(flags); return(len); } /*****************************************************************************/ /* * Generate the serial struct info. */ static void stli_getserial(stliport_t *portp, struct serial_struct *sp) { struct serial_struct sio; stlibrd_t *brdp; #if DEBUG printk("stli_getserial(portp=%x,sp=%x)\n", (int) portp, (int) sp); #endif memset(&sio, 0, sizeof(struct serial_struct)); sio.type = PORT_UNKNOWN; sio.line = portp->portnr; sio.irq = 0; sio.flags = portp->flags; sio.baud_base = portp->baud_base; sio.close_delay = portp->close_delay; sio.closing_wait = portp->closing_wait; sio.custom_divisor = portp->custom_divisor; sio.xmit_fifo_size = 0; sio.hub6 = 0; brdp = stli_brds[portp->brdnr]; if (brdp != (stlibrd_t *) NULL) sio.port = brdp->iobase; copy_to_user(sp, &sio, sizeof(struct serial_struct)); } /*****************************************************************************/ /* * Set port according to the serial struct info. * At this point we do not do any auto-configure stuff, so we will * just quietly ignore any requests to change irq, etc. */ static int stli_setserial(stliport_t *portp, struct serial_struct *sp) { struct serial_struct sio; int rc; #if DEBUG printk("stli_setserial(portp=%x,sp=%x)\n", (int) portp, (int) sp); #endif if (copy_from_user(&sio, sp, sizeof(struct serial_struct))) return -EFAULT; if (!capable(CAP_SYS_ADMIN)) { if ((sio.baud_base != portp->baud_base) || (sio.close_delay != portp->close_delay) || ((sio.flags & ~ASYNC_USR_MASK) != (portp->flags & ~ASYNC_USR_MASK))) return(-EPERM); } portp->flags = (portp->flags & ~ASYNC_USR_MASK) | (sio.flags & ASYNC_USR_MASK); portp->baud_base = sio.baud_base; portp->close_delay = sio.close_delay; portp->closing_wait = sio.closing_wait; portp->custom_divisor = sio.custom_divisor; if ((rc = stli_setport(portp)) < 0) return(rc); return(0); } /*****************************************************************************/ static int stli_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg) { stliport_t *portp; stlibrd_t *brdp; unsigned long lval; unsigned int ival; int rc; #if DEBUG printk("stli_ioctl(tty=%x,file=%x,cmd=%x,arg=%x)\n", (int) tty, (int) file, cmd, (int) arg); #endif if (tty == (struct tty_struct *) NULL) return(-ENODEV); portp = tty->driver_data; if (portp == (stliport_t *) NULL) return(-ENODEV); if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return(0); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(0); if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && (cmd != COM_GETPORTSTATS) && (cmd != COM_CLRPORTSTATS)) { if (tty->flags & (1 << TTY_IO_ERROR)) return(-EIO); } rc = 0; switch (cmd) { case TIOCGSOFTCAR: rc = put_user(((tty->termios->c_cflag & CLOCAL) ? 1 : 0), (unsigned int *) arg); break; case TIOCSSOFTCAR: if ((rc = get_user(ival, (unsigned int *) arg)) == 0) tty->termios->c_cflag = (tty->termios->c_cflag & ~CLOCAL) | (ival ? CLOCAL : 0); break; case TIOCMGET: if ((rc = verify_area(VERIFY_WRITE, (void *) arg, sizeof(unsigned int))) == 0) { if ((rc = stli_cmdwait(brdp, portp, A_GETSIGNALS, &portp->asig, sizeof(asysigs_t), 1)) < 0) return(rc); lval = stli_mktiocm(portp->asig.sigvalue); put_user(lval, (unsigned int *) arg); } break; case TIOCMBIS: if ((rc = get_user(ival, (unsigned int *) arg)) == 0) { stli_mkasysigs(&portp->asig, ((ival & TIOCM_DTR) ? 1 : -1), ((ival & TIOCM_RTS) ? 1 : -1)); rc = stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0); } break; case TIOCMBIC: if ((rc = get_user(ival, (unsigned int *) arg)) == 0) { stli_mkasysigs(&portp->asig, ((ival & TIOCM_DTR) ? 0 : -1), ((ival & TIOCM_RTS) ? 0 : -1)); rc = stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0); } break; case TIOCMSET: if ((rc = get_user(ival, (unsigned int *) arg)) == 0) { stli_mkasysigs(&portp->asig, ((ival & TIOCM_DTR) ? 1 : 0), ((ival & TIOCM_RTS) ? 1 : 0)); rc = stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0); } break; case TIOCGSERIAL: if ((rc = verify_area(VERIFY_WRITE, (void *) arg, sizeof(struct serial_struct))) == 0) stli_getserial(portp, (struct serial_struct *) arg); break; case TIOCSSERIAL: if ((rc = verify_area(VERIFY_READ, (void *) arg, sizeof(struct serial_struct))) == 0) rc = stli_setserial(portp, (struct serial_struct *)arg); break; case STL_GETPFLAG: rc = put_user(portp->pflag, (unsigned int *) arg); break; case STL_SETPFLAG: if ((rc = get_user(portp->pflag, (unsigned int *) arg)) == 0) stli_setport(portp); break; case COM_GETPORTSTATS: if ((rc = verify_area(VERIFY_WRITE, (void *) arg, sizeof(comstats_t))) == 0) rc = stli_getportstats(portp, (comstats_t *) arg); break; case COM_CLRPORTSTATS: if ((rc = verify_area(VERIFY_WRITE, (void *) arg, sizeof(comstats_t))) == 0) rc = stli_clrportstats(portp, (comstats_t *) arg); break; case TIOCSERCONFIG: case TIOCSERGWILD: case TIOCSERSWILD: case TIOCSERGETLSR: case TIOCSERGSTRUCT: case TIOCSERGETMULTI: case TIOCSERSETMULTI: default: rc = -ENOIOCTLCMD; break; } return(rc); } /*****************************************************************************/ /* * This routine assumes that we have user context and can sleep. * Looks like it is true for the current ttys implementation..!! */ static void stli_settermios(struct tty_struct *tty, struct termios *old) { stliport_t *portp; stlibrd_t *brdp; struct termios *tiosp; asyport_t aport; #if DEBUG printk("stli_settermios(tty=%x,old=%x)\n", (int) tty, (int) old); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; tiosp = tty->termios; if ((tiosp->c_cflag == old->c_cflag) && (tiosp->c_iflag == old->c_iflag)) return; stli_mkasyport(portp, &aport, tiosp); stli_cmdwait(brdp, portp, A_SETPORT, &aport, sizeof(asyport_t), 0); stli_mkasysigs(&portp->asig, ((tiosp->c_cflag & CBAUD) ? 1 : 0), -1); stli_cmdwait(brdp, portp, A_SETSIGNALS, &portp->asig, sizeof(asysigs_t), 0); if ((old->c_cflag & CRTSCTS) && ((tiosp->c_cflag & CRTSCTS) == 0)) tty->hw_stopped = 0; if (((old->c_cflag & CLOCAL) == 0) && (tiosp->c_cflag & CLOCAL)) wake_up_interruptible(&portp->open_wait); } /*****************************************************************************/ /* * Attempt to flow control who ever is sending us data. We won't really * do any flow control action here. We can't directly, and even if we * wanted to we would have to send a command to the slave. The slave * knows how to flow control, and will do so when its buffers reach its * internal high water marks. So what we will do is set a local state * bit that will stop us sending any RX data up from the poll routine * (which is the place where RX data from the slave is handled). */ static void stli_throttle(struct tty_struct *tty) { stliport_t *portp; #if DEBUG printk("stli_throttle(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; set_bit(ST_RXSTOP, &portp->state); } /*****************************************************************************/ /* * Unflow control the device sending us data... That means that all * we have to do is clear the RXSTOP state bit. The next poll call * will then be able to pass the RX data back up. */ static void stli_unthrottle(struct tty_struct *tty) { stliport_t *portp; #if DEBUG printk("stli_unthrottle(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; clear_bit(ST_RXSTOP, &portp->state); } /*****************************************************************************/ /* * Stop the transmitter. Basically to do this we will just turn TX * interrupts off. */ static void stli_stop(struct tty_struct *tty) { stlibrd_t *brdp; stliport_t *portp; asyctrl_t actrl; #if DEBUG printk("stli_stop(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; memset(&actrl, 0, sizeof(asyctrl_t)); actrl.txctrl = CT_STOPFLOW; #if 0 stli_cmdwait(brdp, portp, A_PORTCTRL, &actrl, sizeof(asyctrl_t), 0); #endif } /*****************************************************************************/ /* * Start the transmitter again. Just turn TX interrupts back on. */ static void stli_start(struct tty_struct *tty) { stliport_t *portp; stlibrd_t *brdp; asyctrl_t actrl; #if DEBUG printk("stli_start(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; memset(&actrl, 0, sizeof(asyctrl_t)); actrl.txctrl = CT_STARTFLOW; #if 0 stli_cmdwait(brdp, portp, A_PORTCTRL, &actrl, sizeof(asyctrl_t), 0); #endif } /*****************************************************************************/ /* * Scheduler called hang up routine. This is called from the scheduler, * not direct from the driver "poll" routine. We can't call it there * since the real local hangup code will enable/disable the board and * other things that we can't do while handling the poll. Much easier * to deal with it some time later (don't really care when, hangups * aren't that time critical). */ static void stli_dohangup(void *arg) { stliport_t *portp; #if DEBUG printk(KERN_DEBUG "stli_dohangup(portp=%x)\n", (int) arg); #endif /* * FIXME: There's a module removal race here: tty_hangup * calls schedule_task which will call into this * driver later. */ portp = (stliport_t *) arg; if (portp != (stliport_t *) NULL) { if (portp->tty != (struct tty_struct *) NULL) { tty_hangup(portp->tty); } } MOD_DEC_USE_COUNT; } /*****************************************************************************/ /* * Hangup this port. This is pretty much like closing the port, only * a little more brutal. No waiting for data to drain. Shutdown the * port and maybe drop signals. This is rather tricky really. We want * to close the port as well. */ static void stli_hangup(struct tty_struct *tty) { stliport_t *portp; stlibrd_t *brdp; unsigned long flags; #if DEBUG printk(KERN_DEBUG "stli_hangup(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; portp->flags &= ~ASYNC_INITIALIZED; save_flags(flags); cli(); if (! test_bit(ST_CLOSING, &portp->state)) stli_rawclose(brdp, portp, 0, 0); if (tty->termios->c_cflag & HUPCL) { stli_mkasysigs(&portp->asig, 0, 0); if (test_bit(ST_CMDING, &portp->state)) { set_bit(ST_DOSIGS, &portp->state); set_bit(ST_DOFLUSHTX, &portp->state); set_bit(ST_DOFLUSHRX, &portp->state); } else { stli_sendcmd(brdp, portp, A_SETSIGNALSF, &portp->asig, sizeof(asysigs_t), 0); } } restore_flags(flags); clear_bit(ST_TXBUSY, &portp->state); clear_bit(ST_RXSTOP, &portp->state); set_bit(TTY_IO_ERROR, &tty->flags); portp->tty = (struct tty_struct *) NULL; portp->flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CALLOUT_ACTIVE); portp->refcount = 0; wake_up_interruptible(&portp->open_wait); } /*****************************************************************************/ /* * Flush characters from the lower buffer. We may not have user context * so we cannot sleep waiting for it to complete. Also we need to check * if there is chars for this port in the TX cook buffer, and flush them * as well. */ static void stli_flushbuffer(struct tty_struct *tty) { stliport_t *portp; stlibrd_t *brdp; unsigned long ftype, flags; #if DEBUG printk(KERN_DEBUG "stli_flushbuffer(tty=%x)\n", (int) tty); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; save_flags(flags); cli(); if (tty == stli_txcooktty) { stli_txcooktty = (struct tty_struct *) NULL; stli_txcooksize = 0; stli_txcookrealsize = 0; } if (test_bit(ST_CMDING, &portp->state)) { set_bit(ST_DOFLUSHTX, &portp->state); } else { ftype = FLUSHTX; if (test_bit(ST_DOFLUSHRX, &portp->state)) { ftype |= FLUSHRX; clear_bit(ST_DOFLUSHRX, &portp->state); } stli_sendcmd(brdp, portp, A_FLUSH, &ftype, sizeof(unsigned long), 0); } restore_flags(flags); wake_up_interruptible(&tty->write_wait); if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && tty->ldisc.write_wakeup) (tty->ldisc.write_wakeup)(tty); } /*****************************************************************************/ static void stli_breakctl(struct tty_struct *tty, int state) { stlibrd_t *brdp; stliport_t *portp; long arg; /* long savestate, savetime; */ #if DEBUG printk(KERN_DEBUG "stli_breakctl(tty=%x,state=%d)\n", (int) tty, state); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; /* * Due to a bug in the tty send_break() code we need to preserve * the current process state and timeout... savetime = current->timeout; savestate = current->state; */ arg = (state == -1) ? BREAKON : BREAKOFF; stli_cmdwait(brdp, portp, A_BREAK, &arg, sizeof(long), 0); /* * current->timeout = savetime; current->state = savestate; */ } /*****************************************************************************/ static void stli_waituntilsent(struct tty_struct *tty, int timeout) { stliport_t *portp; unsigned long tend; #if DEBUG printk(KERN_DEBUG "stli_waituntilsent(tty=%x,timeout=%x)\n", (int) tty, timeout); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if (timeout == 0) timeout = HZ; tend = jiffies + timeout; while (test_bit(ST_TXBUSY, &portp->state)) { if (signal_pending(current)) break; stli_delay(2); if (time_after_eq(jiffies, tend)) break; } } /*****************************************************************************/ static void stli_sendxchar(struct tty_struct *tty, char ch) { stlibrd_t *brdp; stliport_t *portp; asyctrl_t actrl; #if DEBUG printk(KERN_DEBUG "stli_sendxchar(tty=%x,ch=%x)\n", (int) tty, ch); #endif if (tty == (struct tty_struct *) NULL) return; portp = tty->driver_data; if (portp == (stliport_t *) NULL) return; if ((portp->brdnr < 0) || (portp->brdnr >= stli_nrbrds)) return; brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return; memset(&actrl, 0, sizeof(asyctrl_t)); if (ch == STOP_CHAR(tty)) { actrl.rxctrl = CT_STOPFLOW; } else if (ch == START_CHAR(tty)) { actrl.rxctrl = CT_STARTFLOW; } else { actrl.txctrl = CT_SENDCHR; actrl.tximdch = ch; } stli_cmdwait(brdp, portp, A_PORTCTRL, &actrl, sizeof(asyctrl_t), 0); } /*****************************************************************************/ #define MAXLINE 80 /* * Format info for a specified port. The line is deliberately limited * to 80 characters. (If it is too long it will be truncated, if too * short then padded with spaces). */ static int stli_portinfo(stlibrd_t *brdp, stliport_t *portp, int portnr, char *pos) { char *sp, *uart; int rc, cnt; rc = stli_portcmdstats(portp); uart = "UNKNOWN"; if (brdp->state & BST_STARTED) { switch (stli_comstats.hwid) { case 0: uart = "2681"; break; case 1: uart = "SC26198"; break; default: uart = "CD1400"; break; } } sp = pos; sp += sprintf(sp, "%d: uart:%s ", portnr, uart); if ((brdp->state & BST_STARTED) && (rc >= 0)) { sp += sprintf(sp, "tx:%d rx:%d", (int) stli_comstats.txtotal, (int) stli_comstats.rxtotal); if (stli_comstats.rxframing) sp += sprintf(sp, " fe:%d", (int) stli_comstats.rxframing); if (stli_comstats.rxparity) sp += sprintf(sp, " pe:%d", (int) stli_comstats.rxparity); if (stli_comstats.rxbreaks) sp += sprintf(sp, " brk:%d", (int) stli_comstats.rxbreaks); if (stli_comstats.rxoverrun) sp += sprintf(sp, " oe:%d", (int) stli_comstats.rxoverrun); cnt = sprintf(sp, "%s%s%s%s%s ", (stli_comstats.signals & TIOCM_RTS) ? "|RTS" : "", (stli_comstats.signals & TIOCM_CTS) ? "|CTS" : "", (stli_comstats.signals & TIOCM_DTR) ? "|DTR" : "", (stli_comstats.signals & TIOCM_CD) ? "|DCD" : "", (stli_comstats.signals & TIOCM_DSR) ? "|DSR" : ""); *sp = ' '; sp += cnt; } for (cnt = (sp - pos); (cnt < (MAXLINE - 1)); cnt++) *sp++ = ' '; if (cnt >= MAXLINE) pos[(MAXLINE - 2)] = '+'; pos[(MAXLINE - 1)] = '\n'; return(MAXLINE); } /*****************************************************************************/ /* * Port info, read from the /proc file system. */ static int stli_readproc(char *page, char **start, off_t off, int count, int *eof, void *data) { stlibrd_t *brdp; stliport_t *portp; int brdnr, portnr, totalport; int curoff, maxoff; char *pos; #if DEBUG printk(KERN_DEBUG "stli_readproc(page=%x,start=%x,off=%x,count=%d,eof=%x," "data=%x\n", (int) page, (int) start, (int) off, count, (int) eof, (int) data); #endif pos = page; totalport = 0; curoff = 0; if (off == 0) { pos += sprintf(pos, "%s: version %s", stli_drvtitle, stli_drvversion); while (pos < (page + MAXLINE - 1)) *pos++ = ' '; *pos++ = '\n'; } curoff = MAXLINE; /* * We scan through for each board, panel and port. The offset is * calculated on the fly, and irrelevant ports are skipped. */ for (brdnr = 0; (brdnr < stli_nrbrds); brdnr++) { brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) continue; if (brdp->state == 0) continue; maxoff = curoff + (brdp->nrports * MAXLINE); if (off >= maxoff) { curoff = maxoff; continue; } totalport = brdnr * STL_MAXPORTS; for (portnr = 0; (portnr < brdp->nrports); portnr++, totalport++) { portp = brdp->ports[portnr]; if (portp == (stliport_t *) NULL) continue; if (off >= (curoff += MAXLINE)) continue; if ((pos - page + MAXLINE) > count) goto stli_readdone; pos += stli_portinfo(brdp, portp, totalport, pos); } } *eof = 1; stli_readdone: *start = page; return(pos - page); } /*****************************************************************************/ /* * Generic send command routine. This will send a message to the slave, * of the specified type with the specified argument. Must be very * careful of data that will be copied out from shared memory - * containing command results. The command completion is all done from * a poll routine that does not have user context. Therefore you cannot * copy back directly into user space, or to the kernel stack of a * process. This routine does not sleep, so can be called from anywhere. */ static void stli_sendcmd(stlibrd_t *brdp, stliport_t *portp, unsigned long cmd, void *arg, int size, int copyback) { volatile cdkhdr_t *hdrp; volatile cdkctrl_t *cp; volatile unsigned char *bits; unsigned long flags; #if DEBUG printk(KERN_DEBUG "stli_sendcmd(brdp=%x,portp=%x,cmd=%x,arg=%x,size=%d," "copyback=%d)\n", (int) brdp, (int) portp, (int) cmd, (int) arg, size, copyback); #endif save_flags(flags); cli(); if (test_bit(ST_CMDING, &portp->state)) { printk(KERN_ERR "STALLION: command already busy, cmd=%x!\n", (int) cmd); restore_flags(flags); return; } EBRDENABLE(brdp); cp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->ctrl; if (size > 0) { memcpy((void *) &(cp->args[0]), arg, size); if (copyback) { portp->argp = arg; portp->argsize = size; } } cp->status = 0; cp->cmd = cmd; hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); bits = ((volatile unsigned char *) hdrp) + brdp->slaveoffset + portp->portidx; *bits |= portp->portbit; set_bit(ST_CMDING, &portp->state); EBRDDISABLE(brdp); restore_flags(flags); } /*****************************************************************************/ /* * Read data from shared memory. This assumes that the shared memory * is enabled and that interrupts are off. Basically we just empty out * the shared memory buffer into the tty buffer. Must be careful to * handle the case where we fill up the tty buffer, but still have * more chars to unload. */ static inline void stli_read(stlibrd_t *brdp, stliport_t *portp) { volatile cdkasyrq_t *rp; volatile char *shbuf; struct tty_struct *tty; unsigned int head, tail, size; unsigned int len, stlen; #if DEBUG printk(KERN_DEBUG "stli_read(brdp=%x,portp=%d)\n", (int) brdp, (int) portp); #endif if (test_bit(ST_RXSTOP, &portp->state)) return; tty = portp->tty; if (tty == (struct tty_struct *) NULL) return; rp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->rxq; head = (unsigned int) rp->head; if (head != ((unsigned int) rp->head)) head = (unsigned int) rp->head; tail = (unsigned int) rp->tail; size = portp->rxsize; if (head >= tail) { len = head - tail; stlen = len; } else { len = size - (tail - head); stlen = size - tail; } len = MIN(len, (TTY_FLIPBUF_SIZE - tty->flip.count)); shbuf = (volatile char *) EBRDGETMEMPTR(brdp, portp->rxoffset); while (len > 0) { stlen = MIN(len, stlen); memcpy(tty->flip.char_buf_ptr, (char *) (shbuf + tail), stlen); memset(tty->flip.flag_buf_ptr, 0, stlen); tty->flip.char_buf_ptr += stlen; tty->flip.flag_buf_ptr += stlen; tty->flip.count += stlen; len -= stlen; tail += stlen; if (tail >= size) { tail = 0; stlen = head; } } rp = &((volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr))->rxq; rp->tail = tail; if (head != tail) set_bit(ST_RXING, &portp->state); tty_schedule_flip(tty); } /*****************************************************************************/ /* * Set up and carry out any delayed commands. There is only a small set * of slave commands that can be done "off-level". So it is not too * difficult to deal with them here. */ static inline void stli_dodelaycmd(stliport_t *portp, volatile cdkctrl_t *cp) { int cmd; if (test_bit(ST_DOSIGS, &portp->state)) { if (test_bit(ST_DOFLUSHTX, &portp->state) && test_bit(ST_DOFLUSHRX, &portp->state)) cmd = A_SETSIGNALSF; else if (test_bit(ST_DOFLUSHTX, &portp->state)) cmd = A_SETSIGNALSFTX; else if (test_bit(ST_DOFLUSHRX, &portp->state)) cmd = A_SETSIGNALSFRX; else cmd = A_SETSIGNALS; clear_bit(ST_DOFLUSHTX, &portp->state); clear_bit(ST_DOFLUSHRX, &portp->state); clear_bit(ST_DOSIGS, &portp->state); memcpy((void *) &(cp->args[0]), (void *) &portp->asig, sizeof(asysigs_t)); cp->status = 0; cp->cmd = cmd; set_bit(ST_CMDING, &portp->state); } else if (test_bit(ST_DOFLUSHTX, &portp->state) || test_bit(ST_DOFLUSHRX, &portp->state)) { cmd = ((test_bit(ST_DOFLUSHTX, &portp->state)) ? FLUSHTX : 0); cmd |= ((test_bit(ST_DOFLUSHRX, &portp->state)) ? FLUSHRX : 0); clear_bit(ST_DOFLUSHTX, &portp->state); clear_bit(ST_DOFLUSHRX, &portp->state); memcpy((void *) &(cp->args[0]), (void *) &cmd, sizeof(int)); cp->status = 0; cp->cmd = A_FLUSH; set_bit(ST_CMDING, &portp->state); } } /*****************************************************************************/ /* * Host command service checking. This handles commands or messages * coming from the slave to the host. Must have board shared memory * enabled and interrupts off when called. Notice that by servicing the * read data last we don't need to change the shared memory pointer * during processing (which is a slow IO operation). * Return value indicates if this port is still awaiting actions from * the slave (like open, command, or even TX data being sent). If 0 * then port is still busy, otherwise no longer busy. */ static inline int stli_hostcmd(stlibrd_t *brdp, stliport_t *portp) { volatile cdkasy_t *ap; volatile cdkctrl_t *cp; struct tty_struct *tty; asynotify_t nt; unsigned long oldsigs; int rc, donerx; #if DEBUG printk(KERN_DEBUG "stli_hostcmd(brdp=%x,channr=%d)\n", (int) brdp, channr); #endif ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); cp = &ap->ctrl; /* * Check if we are waiting for an open completion message. */ if (test_bit(ST_OPENING, &portp->state)) { rc = (int) cp->openarg; if ((cp->open == 0) && (rc != 0)) { if (rc > 0) rc--; cp->openarg = 0; portp->rc = rc; clear_bit(ST_OPENING, &portp->state); wake_up_interruptible(&portp->raw_wait); } } /* * Check if we are waiting for a close completion message. */ if (test_bit(ST_CLOSING, &portp->state)) { rc = (int) cp->closearg; if ((cp->close == 0) && (rc != 0)) { if (rc > 0) rc--; cp->closearg = 0; portp->rc = rc; clear_bit(ST_CLOSING, &portp->state); wake_up_interruptible(&portp->raw_wait); } } /* * Check if we are waiting for a command completion message. We may * need to copy out the command results associated with this command. */ if (test_bit(ST_CMDING, &portp->state)) { rc = cp->status; if ((cp->cmd == 0) && (rc != 0)) { if (rc > 0) rc--; if (portp->argp != (void *) NULL) { memcpy(portp->argp, (void *) &(cp->args[0]), portp->argsize); portp->argp = (void *) NULL; } cp->status = 0; portp->rc = rc; clear_bit(ST_CMDING, &portp->state); stli_dodelaycmd(portp, cp); wake_up_interruptible(&portp->raw_wait); } } /* * Check for any notification messages ready. This includes lots of * different types of events - RX chars ready, RX break received, * TX data low or empty in the slave, modem signals changed state. */ donerx = 0; if (ap->notify) { nt = ap->changed; ap->notify = 0; tty = portp->tty; if (nt.signal & SG_DCD) { oldsigs = portp->sigs; portp->sigs = stli_mktiocm(nt.sigvalue); clear_bit(ST_GETSIGS, &portp->state); if ((portp->sigs & TIOCM_CD) && ((oldsigs & TIOCM_CD) == 0)) wake_up_interruptible(&portp->open_wait); if ((oldsigs & TIOCM_CD) && ((portp->sigs & TIOCM_CD) == 0)) { if (portp->flags & ASYNC_CHECK_CD) { if (! ((portp->flags & ASYNC_CALLOUT_ACTIVE) && (portp->flags & ASYNC_CALLOUT_NOHUP))) { if (tty != (struct tty_struct *) NULL) { MOD_INC_USE_COUNT; if (schedule_task(&portp->tqhangup) == 0) MOD_DEC_USE_COUNT; } } } } } if (nt.data & DT_TXEMPTY) clear_bit(ST_TXBUSY, &portp->state); if (nt.data & (DT_TXEMPTY | DT_TXLOW)) { if (tty != (struct tty_struct *) NULL) { if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && tty->ldisc.write_wakeup) { (tty->ldisc.write_wakeup)(tty); EBRDENABLE(brdp); } wake_up_interruptible(&tty->write_wait); } } if ((nt.data & DT_RXBREAK) && (portp->rxmarkmsk & BRKINT)) { if (tty != (struct tty_struct *) NULL) { if (tty->flip.count < TTY_FLIPBUF_SIZE) { tty->flip.count++; *tty->flip.flag_buf_ptr++ = TTY_BREAK; *tty->flip.char_buf_ptr++ = 0; if (portp->flags & ASYNC_SAK) { do_SAK(tty); EBRDENABLE(brdp); } tty_schedule_flip(tty); } } } if (nt.data & DT_RXBUSY) { donerx++; stli_read(brdp, portp); } } /* * It might seem odd that we are checking for more RX chars here. * But, we need to handle the case where the tty buffer was previously * filled, but we had more characters to pass up. The slave will not * send any more RX notify messages until the RX buffer has been emptied. * But it will leave the service bits on (since the buffer is not empty). * So from here we can try to process more RX chars. */ if ((!donerx) && test_bit(ST_RXING, &portp->state)) { clear_bit(ST_RXING, &portp->state); stli_read(brdp, portp); } return((test_bit(ST_OPENING, &portp->state) || test_bit(ST_CLOSING, &portp->state) || test_bit(ST_CMDING, &portp->state) || test_bit(ST_TXBUSY, &portp->state) || test_bit(ST_RXING, &portp->state)) ? 0 : 1); } /*****************************************************************************/ /* * Service all ports on a particular board. Assumes that the boards * shared memory is enabled, and that the page pointer is pointed * at the cdk header structure. */ static inline void stli_brdpoll(stlibrd_t *brdp, volatile cdkhdr_t *hdrp) { stliport_t *portp; unsigned char hostbits[(STL_MAXCHANS / 8) + 1]; unsigned char slavebits[(STL_MAXCHANS / 8) + 1]; unsigned char *slavep; int bitpos, bitat, bitsize; int channr, nrdevs, slavebitchange; bitsize = brdp->bitsize; nrdevs = brdp->nrdevs; /* * Check if slave wants any service. Basically we try to do as * little work as possible here. There are 2 levels of service * bits. So if there is nothing to do we bail early. We check * 8 service bits at a time in the inner loop, so we can bypass * the lot if none of them want service. */ memcpy(&hostbits[0], (((unsigned char *) hdrp) + brdp->hostoffset), bitsize); memset(&slavebits[0], 0, bitsize); slavebitchange = 0; for (bitpos = 0; (bitpos < bitsize); bitpos++) { if (hostbits[bitpos] == 0) continue; channr = bitpos * 8; for (bitat = 0x1; (channr < nrdevs); channr++, bitat <<= 1) { if (hostbits[bitpos] & bitat) { portp = brdp->ports[(channr - 1)]; if (stli_hostcmd(brdp, portp)) { slavebitchange++; slavebits[bitpos] |= bitat; } } } } /* * If any of the ports are no longer busy then update them in the * slave request bits. We need to do this after, since a host port * service may initiate more slave requests. */ if (slavebitchange) { hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); slavep = ((unsigned char *) hdrp) + brdp->slaveoffset; for (bitpos = 0; (bitpos < bitsize); bitpos++) { if (slavebits[bitpos]) slavep[bitpos] &= ~slavebits[bitpos]; } } } /*****************************************************************************/ /* * Driver poll routine. This routine polls the boards in use and passes * messages back up to host when necessary. This is actually very * CPU efficient, since we will always have the kernel poll clock, it * adds only a few cycles when idle (since board service can be * determined very easily), but when loaded generates no interrupts * (with their expensive associated context change). */ static void stli_poll(unsigned long arg) { volatile cdkhdr_t *hdrp; stlibrd_t *brdp; int brdnr; stli_timerlist.expires = STLI_TIMEOUT; add_timer(&stli_timerlist); /* * Check each board and do any servicing required. */ for (brdnr = 0; (brdnr < stli_nrbrds); brdnr++) { brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) continue; if ((brdp->state & BST_STARTED) == 0) continue; EBRDENABLE(brdp); hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); if (hdrp->hostreq) stli_brdpoll(brdp, hdrp); EBRDDISABLE(brdp); } } /*****************************************************************************/ /* * Translate the termios settings into the port setting structure of * the slave. */ static void stli_mkasyport(stliport_t *portp, asyport_t *pp, struct termios *tiosp) { #if DEBUG printk(KERN_DEBUG "stli_mkasyport(portp=%x,pp=%x,tiosp=%d)\n", (int) portp, (int) pp, (int) tiosp); #endif memset(pp, 0, sizeof(asyport_t)); /* * Start of by setting the baud, char size, parity and stop bit info. */ pp->baudout = tiosp->c_cflag & CBAUD; if (pp->baudout & CBAUDEX) { pp->baudout &= ~CBAUDEX; if ((pp->baudout < 1) || (pp->baudout > 4)) tiosp->c_cflag &= ~CBAUDEX; else pp->baudout += 15; } pp->baudout = stli_baudrates[pp->baudout]; if ((tiosp->c_cflag & CBAUD) == B38400) { if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) pp->baudout = 57600; else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) pp->baudout = 115200; else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) pp->baudout = 230400; else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) pp->baudout = 460800; else if ((portp->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) pp->baudout = (portp->baud_base / portp->custom_divisor); } if (pp->baudout > STL_MAXBAUD) pp->baudout = STL_MAXBAUD; pp->baudin = pp->baudout; switch (tiosp->c_cflag & CSIZE) { case CS5: pp->csize = 5; break; case CS6: pp->csize = 6; break; case CS7: pp->csize = 7; break; default: pp->csize = 8; break; } if (tiosp->c_cflag & CSTOPB) pp->stopbs = PT_STOP2; else pp->stopbs = PT_STOP1; if (tiosp->c_cflag & PARENB) { if (tiosp->c_cflag & PARODD) pp->parity = PT_ODDPARITY; else pp->parity = PT_EVENPARITY; } else { pp->parity = PT_NOPARITY; } /* * Set up any flow control options enabled. */ if (tiosp->c_iflag & IXON) { pp->flow |= F_IXON; if (tiosp->c_iflag & IXANY) pp->flow |= F_IXANY; } if (tiosp->c_cflag & CRTSCTS) pp->flow |= (F_RTSFLOW | F_CTSFLOW); pp->startin = tiosp->c_cc[VSTART]; pp->stopin = tiosp->c_cc[VSTOP]; pp->startout = tiosp->c_cc[VSTART]; pp->stopout = tiosp->c_cc[VSTOP]; /* * Set up the RX char marking mask with those RX error types we must * catch. We can get the slave to help us out a little here, it will * ignore parity errors and breaks for us, and mark parity errors in * the data stream. */ if (tiosp->c_iflag & IGNPAR) pp->iflag |= FI_IGNRXERRS; if (tiosp->c_iflag & IGNBRK) pp->iflag |= FI_IGNBREAK; portp->rxmarkmsk = 0; if (tiosp->c_iflag & (INPCK | PARMRK)) pp->iflag |= FI_1MARKRXERRS; if (tiosp->c_iflag & BRKINT) portp->rxmarkmsk |= BRKINT; /* * Set up clocal processing as required. */ if (tiosp->c_cflag & CLOCAL) portp->flags &= ~ASYNC_CHECK_CD; else portp->flags |= ASYNC_CHECK_CD; /* * Transfer any persistent flags into the asyport structure. */ pp->pflag = (portp->pflag & 0xffff); pp->vmin = (portp->pflag & P_RXIMIN) ? 1 : 0; pp->vtime = (portp->pflag & P_RXITIME) ? 1 : 0; pp->cc[1] = (portp->pflag & P_RXTHOLD) ? 1 : 0; } /*****************************************************************************/ /* * Construct a slave signals structure for setting the DTR and RTS * signals as specified. */ static void stli_mkasysigs(asysigs_t *sp, int dtr, int rts) { #if DEBUG printk(KERN_DEBUG "stli_mkasysigs(sp=%x,dtr=%d,rts=%d)\n", (int) sp, dtr, rts); #endif memset(sp, 0, sizeof(asysigs_t)); if (dtr >= 0) { sp->signal |= SG_DTR; sp->sigvalue |= ((dtr > 0) ? SG_DTR : 0); } if (rts >= 0) { sp->signal |= SG_RTS; sp->sigvalue |= ((rts > 0) ? SG_RTS : 0); } } /*****************************************************************************/ /* * Convert the signals returned from the slave into a local TIOCM type * signals value. We keep them locally in TIOCM format. */ static long stli_mktiocm(unsigned long sigvalue) { long tiocm; #if DEBUG printk(KERN_DEBUG "stli_mktiocm(sigvalue=%x)\n", (int) sigvalue); #endif tiocm = 0; tiocm |= ((sigvalue & SG_DCD) ? TIOCM_CD : 0); tiocm |= ((sigvalue & SG_CTS) ? TIOCM_CTS : 0); tiocm |= ((sigvalue & SG_RI) ? TIOCM_RI : 0); tiocm |= ((sigvalue & SG_DSR) ? TIOCM_DSR : 0); tiocm |= ((sigvalue & SG_DTR) ? TIOCM_DTR : 0); tiocm |= ((sigvalue & SG_RTS) ? TIOCM_RTS : 0); return(tiocm); } /*****************************************************************************/ /* * All panels and ports actually attached have been worked out. All * we need to do here is set up the appropriate per port data structures. */ static inline int stli_initports(stlibrd_t *brdp) { stliport_t *portp; int i, panelnr, panelport; #if DEBUG printk(KERN_DEBUG "stli_initports(brdp=%x)\n", (int) brdp); #endif for (i = 0, panelnr = 0, panelport = 0; (i < brdp->nrports); i++) { portp = (stliport_t *) stli_memalloc(sizeof(stliport_t)); if (portp == (stliport_t *) NULL) { printk("STALLION: failed to allocate port structure\n"); continue; } memset(portp, 0, sizeof(stliport_t)); portp->magic = STLI_PORTMAGIC; portp->portnr = i; portp->brdnr = brdp->brdnr; portp->panelnr = panelnr; portp->baud_base = STL_BAUDBASE; portp->close_delay = STL_CLOSEDELAY; portp->closing_wait = 30 * HZ; portp->tqhangup.routine = stli_dohangup; portp->tqhangup.data = portp; init_waitqueue_head(&portp->open_wait); init_waitqueue_head(&portp->close_wait); init_waitqueue_head(&portp->raw_wait); portp->normaltermios = stli_deftermios; portp->callouttermios = stli_deftermios; panelport++; if (panelport >= brdp->panels[panelnr]) { panelport = 0; panelnr++; } brdp->ports[i] = portp; } return(0); } /*****************************************************************************/ /* * All the following routines are board specific hardware operations. */ static void stli_ecpinit(stlibrd_t *brdp) { unsigned long memconf; #if DEBUG printk(KERN_DEBUG "stli_ecpinit(brdp=%d)\n", (int) brdp); #endif outb(ECP_ATSTOP, (brdp->iobase + ECP_ATCONFR)); udelay(10); outb(ECP_ATDISABLE, (brdp->iobase + ECP_ATCONFR)); udelay(100); memconf = (brdp->memaddr & ECP_ATADDRMASK) >> ECP_ATADDRSHFT; outb(memconf, (brdp->iobase + ECP_ATMEMAR)); } /*****************************************************************************/ static void stli_ecpenable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_ecpenable(brdp=%x)\n", (int) brdp); #endif outb(ECP_ATENABLE, (brdp->iobase + ECP_ATCONFR)); } /*****************************************************************************/ static void stli_ecpdisable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_ecpdisable(brdp=%x)\n", (int) brdp); #endif outb(ECP_ATDISABLE, (brdp->iobase + ECP_ATCONFR)); } /*****************************************************************************/ static char *stli_ecpgetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; #if DEBUG printk(KERN_DEBUG "stli_ecpgetmemptr(brdp=%x,offset=%x)\n", (int) brdp, (int) offset); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % ECP_ATPAGESIZE); val = (unsigned char) (offset / ECP_ATPAGESIZE); } outb(val, (brdp->iobase + ECP_ATMEMPR)); return(ptr); } /*****************************************************************************/ static void stli_ecpreset(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_ecpreset(brdp=%x)\n", (int) brdp); #endif outb(ECP_ATSTOP, (brdp->iobase + ECP_ATCONFR)); udelay(10); outb(ECP_ATDISABLE, (brdp->iobase + ECP_ATCONFR)); udelay(500); } /*****************************************************************************/ static void stli_ecpintr(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_ecpintr(brdp=%x)\n", (int) brdp); #endif outb(0x1, brdp->iobase); } /*****************************************************************************/ /* * The following set of functions act on ECP EISA boards. */ static void stli_ecpeiinit(stlibrd_t *brdp) { unsigned long memconf; #if DEBUG printk(KERN_DEBUG "stli_ecpeiinit(brdp=%x)\n", (int) brdp); #endif outb(0x1, (brdp->iobase + ECP_EIBRDENAB)); outb(ECP_EISTOP, (brdp->iobase + ECP_EICONFR)); udelay(10); outb(ECP_EIDISABLE, (brdp->iobase + ECP_EICONFR)); udelay(500); memconf = (brdp->memaddr & ECP_EIADDRMASKL) >> ECP_EIADDRSHFTL; outb(memconf, (brdp->iobase + ECP_EIMEMARL)); memconf = (brdp->memaddr & ECP_EIADDRMASKH) >> ECP_EIADDRSHFTH; outb(memconf, (brdp->iobase + ECP_EIMEMARH)); } /*****************************************************************************/ static void stli_ecpeienable(stlibrd_t *brdp) { outb(ECP_EIENABLE, (brdp->iobase + ECP_EICONFR)); } /*****************************************************************************/ static void stli_ecpeidisable(stlibrd_t *brdp) { outb(ECP_EIDISABLE, (brdp->iobase + ECP_EICONFR)); } /*****************************************************************************/ static char *stli_ecpeigetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; #if DEBUG printk(KERN_DEBUG "stli_ecpeigetmemptr(brdp=%x,offset=%x,line=%d)\n", (int) brdp, (int) offset, line); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % ECP_EIPAGESIZE); if (offset < ECP_EIPAGESIZE) val = ECP_EIENABLE; else val = ECP_EIENABLE | 0x40; } outb(val, (brdp->iobase + ECP_EICONFR)); return(ptr); } /*****************************************************************************/ static void stli_ecpeireset(stlibrd_t *brdp) { outb(ECP_EISTOP, (brdp->iobase + ECP_EICONFR)); udelay(10); outb(ECP_EIDISABLE, (brdp->iobase + ECP_EICONFR)); udelay(500); } /*****************************************************************************/ /* * The following set of functions act on ECP MCA boards. */ static void stli_ecpmcenable(stlibrd_t *brdp) { outb(ECP_MCENABLE, (brdp->iobase + ECP_MCCONFR)); } /*****************************************************************************/ static void stli_ecpmcdisable(stlibrd_t *brdp) { outb(ECP_MCDISABLE, (brdp->iobase + ECP_MCCONFR)); } /*****************************************************************************/ static char *stli_ecpmcgetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % ECP_MCPAGESIZE); val = ((unsigned char) (offset / ECP_MCPAGESIZE)) | ECP_MCENABLE; } outb(val, (brdp->iobase + ECP_MCCONFR)); return(ptr); } /*****************************************************************************/ static void stli_ecpmcreset(stlibrd_t *brdp) { outb(ECP_MCSTOP, (brdp->iobase + ECP_MCCONFR)); udelay(10); outb(ECP_MCDISABLE, (brdp->iobase + ECP_MCCONFR)); udelay(500); } /*****************************************************************************/ /* * The following set of functions act on ECP PCI boards. */ static void stli_ecppciinit(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_ecppciinit(brdp=%x)\n", (int) brdp); #endif outb(ECP_PCISTOP, (brdp->iobase + ECP_PCICONFR)); udelay(10); outb(0, (brdp->iobase + ECP_PCICONFR)); udelay(500); } /*****************************************************************************/ static char *stli_ecppcigetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; #if DEBUG printk(KERN_DEBUG "stli_ecppcigetmemptr(brdp=%x,offset=%x,line=%d)\n", (int) brdp, (int) offset, line); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), board=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % ECP_PCIPAGESIZE); val = (offset / ECP_PCIPAGESIZE) << 1; } outb(val, (brdp->iobase + ECP_PCICONFR)); return(ptr); } /*****************************************************************************/ static void stli_ecppcireset(stlibrd_t *brdp) { outb(ECP_PCISTOP, (brdp->iobase + ECP_PCICONFR)); udelay(10); outb(0, (brdp->iobase + ECP_PCICONFR)); udelay(500); } /*****************************************************************************/ /* * The following routines act on ONboards. */ static void stli_onbinit(stlibrd_t *brdp) { unsigned long memconf; #if DEBUG printk(KERN_DEBUG "stli_onbinit(brdp=%d)\n", (int) brdp); #endif outb(ONB_ATSTOP, (brdp->iobase + ONB_ATCONFR)); udelay(10); outb(ONB_ATDISABLE, (brdp->iobase + ONB_ATCONFR)); mdelay(1000); memconf = (brdp->memaddr & ONB_ATADDRMASK) >> ONB_ATADDRSHFT; outb(memconf, (brdp->iobase + ONB_ATMEMAR)); outb(0x1, brdp->iobase); mdelay(1); } /*****************************************************************************/ static void stli_onbenable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_onbenable(brdp=%x)\n", (int) brdp); #endif outb((brdp->enabval | ONB_ATENABLE), (brdp->iobase + ONB_ATCONFR)); } /*****************************************************************************/ static void stli_onbdisable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_onbdisable(brdp=%x)\n", (int) brdp); #endif outb((brdp->enabval | ONB_ATDISABLE), (brdp->iobase + ONB_ATCONFR)); } /*****************************************************************************/ static char *stli_onbgetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; #if DEBUG printk(KERN_DEBUG "stli_onbgetmemptr(brdp=%x,offset=%x)\n", (int) brdp, (int) offset); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; } else { ptr = brdp->membase + (offset % ONB_ATPAGESIZE); } return(ptr); } /*****************************************************************************/ static void stli_onbreset(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_onbreset(brdp=%x)\n", (int) brdp); #endif outb(ONB_ATSTOP, (brdp->iobase + ONB_ATCONFR)); udelay(10); outb(ONB_ATDISABLE, (brdp->iobase + ONB_ATCONFR)); mdelay(1000); } /*****************************************************************************/ /* * The following routines act on ONboard EISA. */ static void stli_onbeinit(stlibrd_t *brdp) { unsigned long memconf; #if DEBUG printk(KERN_DEBUG "stli_onbeinit(brdp=%d)\n", (int) brdp); #endif outb(0x1, (brdp->iobase + ONB_EIBRDENAB)); outb(ONB_EISTOP, (brdp->iobase + ONB_EICONFR)); udelay(10); outb(ONB_EIDISABLE, (brdp->iobase + ONB_EICONFR)); mdelay(1000); memconf = (brdp->memaddr & ONB_EIADDRMASKL) >> ONB_EIADDRSHFTL; outb(memconf, (brdp->iobase + ONB_EIMEMARL)); memconf = (brdp->memaddr & ONB_EIADDRMASKH) >> ONB_EIADDRSHFTH; outb(memconf, (brdp->iobase + ONB_EIMEMARH)); outb(0x1, brdp->iobase); mdelay(1); } /*****************************************************************************/ static void stli_onbeenable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_onbeenable(brdp=%x)\n", (int) brdp); #endif outb(ONB_EIENABLE, (brdp->iobase + ONB_EICONFR)); } /*****************************************************************************/ static void stli_onbedisable(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_onbedisable(brdp=%x)\n", (int) brdp); #endif outb(ONB_EIDISABLE, (brdp->iobase + ONB_EICONFR)); } /*****************************************************************************/ static char *stli_onbegetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; #if DEBUG printk(KERN_DEBUG "stli_onbegetmemptr(brdp=%x,offset=%x,line=%d)\n", (int) brdp, (int) offset, line); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % ONB_EIPAGESIZE); if (offset < ONB_EIPAGESIZE) val = ONB_EIENABLE; else val = ONB_EIENABLE | 0x40; } outb(val, (brdp->iobase + ONB_EICONFR)); return(ptr); } /*****************************************************************************/ static void stli_onbereset(stlibrd_t *brdp) { #if DEBUG printk(KERN_ERR "stli_onbereset(brdp=%x)\n", (int) brdp); #endif outb(ONB_EISTOP, (brdp->iobase + ONB_EICONFR)); udelay(10); outb(ONB_EIDISABLE, (brdp->iobase + ONB_EICONFR)); mdelay(1000); } /*****************************************************************************/ /* * The following routines act on Brumby boards. */ static void stli_bbyinit(stlibrd_t *brdp) { #if DEBUG printk(KERN_ERR "stli_bbyinit(brdp=%d)\n", (int) brdp); #endif outb(BBY_ATSTOP, (brdp->iobase + BBY_ATCONFR)); udelay(10); outb(0, (brdp->iobase + BBY_ATCONFR)); mdelay(1000); outb(0x1, brdp->iobase); mdelay(1); } /*****************************************************************************/ static char *stli_bbygetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; unsigned char val; #if DEBUG printk(KERN_ERR "stli_bbygetmemptr(brdp=%x,offset=%x)\n", (int) brdp, (int) offset); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; val = 0; } else { ptr = brdp->membase + (offset % BBY_PAGESIZE); val = (unsigned char) (offset / BBY_PAGESIZE); } outb(val, (brdp->iobase + BBY_ATCONFR)); return(ptr); } /*****************************************************************************/ static void stli_bbyreset(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_bbyreset(brdp=%x)\n", (int) brdp); #endif outb(BBY_ATSTOP, (brdp->iobase + BBY_ATCONFR)); udelay(10); outb(0, (brdp->iobase + BBY_ATCONFR)); mdelay(1000); } /*****************************************************************************/ /* * The following routines act on original old Stallion boards. */ static void stli_stalinit(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_stalinit(brdp=%d)\n", (int) brdp); #endif outb(0x1, brdp->iobase); mdelay(1000); } /*****************************************************************************/ static char *stli_stalgetmemptr(stlibrd_t *brdp, unsigned long offset, int line) { void *ptr; #if DEBUG printk(KERN_DEBUG "stli_stalgetmemptr(brdp=%x,offset=%x)\n", (int) brdp, (int) offset); #endif if (offset > brdp->memsize) { printk(KERN_ERR "STALLION: shared memory pointer=%x out of " "range at line=%d(%d), brd=%d\n", (int) offset, line, __LINE__, brdp->brdnr); ptr = 0; } else { ptr = brdp->membase + (offset % STAL_PAGESIZE); } return(ptr); } /*****************************************************************************/ static void stli_stalreset(stlibrd_t *brdp) { volatile unsigned long *vecp; #if DEBUG printk(KERN_DEBUG "stli_stalreset(brdp=%x)\n", (int) brdp); #endif vecp = (volatile unsigned long *) (brdp->membase + 0x30); *vecp = 0xffff0000; outb(0, brdp->iobase); mdelay(1000); } /*****************************************************************************/ /* * Try to find an ECP board and initialize it. This handles only ECP * board types. */ static inline int stli_initecp(stlibrd_t *brdp) { cdkecpsig_t sig; cdkecpsig_t *sigsp; unsigned int status, nxtid; char *name; int panelnr, nrports; #if DEBUG printk(KERN_DEBUG "stli_initecp(brdp=%x)\n", (int) brdp); #endif /* * Do a basic sanity check on the IO and memory addresses. */ if ((brdp->iobase == 0) || (brdp->memaddr == 0)) return(-ENODEV); brdp->iosize = ECP_IOSIZE; if (check_region(brdp->iobase, brdp->iosize)) printk(KERN_ERR "STALLION: Warning, board %d I/O address %x " "conflicts with another device\n", brdp->brdnr, brdp->iobase); /* * Based on the specific board type setup the common vars to access * and enable shared memory. Set all board specific information now * as well. */ switch (brdp->brdtype) { case BRD_ECP: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ECP_MEMSIZE; brdp->pagesize = ECP_ATPAGESIZE; brdp->init = stli_ecpinit; brdp->enable = stli_ecpenable; brdp->reenable = stli_ecpenable; brdp->disable = stli_ecpdisable; brdp->getmemptr = stli_ecpgetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_ecpreset; name = "serial(EC8/64)"; break; case BRD_ECPE: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ECP_MEMSIZE; brdp->pagesize = ECP_EIPAGESIZE; brdp->init = stli_ecpeiinit; brdp->enable = stli_ecpeienable; brdp->reenable = stli_ecpeienable; brdp->disable = stli_ecpeidisable; brdp->getmemptr = stli_ecpeigetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_ecpeireset; name = "serial(EC8/64-EI)"; break; case BRD_ECPMC: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ECP_MEMSIZE; brdp->pagesize = ECP_MCPAGESIZE; brdp->init = NULL; brdp->enable = stli_ecpmcenable; brdp->reenable = stli_ecpmcenable; brdp->disable = stli_ecpmcdisable; brdp->getmemptr = stli_ecpmcgetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_ecpmcreset; name = "serial(EC8/64-MCA)"; break; case BRD_ECPPCI: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ECP_PCIMEMSIZE; brdp->pagesize = ECP_PCIPAGESIZE; brdp->init = stli_ecppciinit; brdp->enable = NULL; brdp->reenable = NULL; brdp->disable = NULL; brdp->getmemptr = stli_ecppcigetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_ecppcireset; name = "serial(EC/RA-PCI)"; break; default: return(-EINVAL); } /* * The per-board operations structure is all set up, so now let's go * and get the board operational. Firstly initialize board configuration * registers. Set the memory mapping info so we can get at the boards * shared memory. */ EBRDINIT(brdp); brdp->membase = ioremap(brdp->memaddr, brdp->memsize); if (brdp->membase == (void *) NULL) return(-ENOMEM); /* * Now that all specific code is set up, enable the shared memory and * look for the a signature area that will tell us exactly what board * this is, and what it is connected to it. */ EBRDENABLE(brdp); sigsp = (cdkecpsig_t *) EBRDGETMEMPTR(brdp, CDK_SIGADDR); memcpy(&sig, sigsp, sizeof(cdkecpsig_t)); EBRDDISABLE(brdp); #if 0 printk("%s(%d): sig-> magic=%x rom=%x panel=%x,%x,%x,%x,%x,%x,%x,%x\n", __FILE__, __LINE__, (int) sig.magic, sig.romver, sig.panelid[0], (int) sig.panelid[1], (int) sig.panelid[2], (int) sig.panelid[3], (int) sig.panelid[4], (int) sig.panelid[5], (int) sig.panelid[6], (int) sig.panelid[7]); #endif if (sig.magic != ECP_MAGIC) return(-ENODEV); /* * Scan through the signature looking at the panels connected to the * board. Calculate the total number of ports as we go. */ for (panelnr = 0, nxtid = 0; (panelnr < STL_MAXPANELS); panelnr++) { status = sig.panelid[nxtid]; if ((status & ECH_PNLIDMASK) != nxtid) break; brdp->panelids[panelnr] = status; nrports = (status & ECH_PNL16PORT) ? 16 : 8; if ((nrports == 16) && ((status & ECH_PNLXPID) == 0)) nxtid++; brdp->panels[panelnr] = nrports; brdp->nrports += nrports; nxtid++; brdp->nrpanels++; } request_region(brdp->iobase, brdp->iosize, name); brdp->state |= BST_FOUND; return(0); } /*****************************************************************************/ /* * Try to find an ONboard, Brumby or Stallion board and initialize it. * This handles only these board types. */ static inline int stli_initonb(stlibrd_t *brdp) { cdkonbsig_t sig; cdkonbsig_t *sigsp; char *name; int i; #if DEBUG printk(KERN_DEBUG "stli_initonb(brdp=%x)\n", (int) brdp); #endif /* * Do a basic sanity check on the IO and memory addresses. */ if ((brdp->iobase == 0) || (brdp->memaddr == 0)) return(-ENODEV); brdp->iosize = ONB_IOSIZE; if (check_region(brdp->iobase, brdp->iosize)) printk(KERN_ERR "STALLION: Warning, board %d I/O address %x " "conflicts with another device\n", brdp->brdnr, brdp->iobase); /* * Based on the specific board type setup the common vars to access * and enable shared memory. Set all board specific information now * as well. */ switch (brdp->brdtype) { case BRD_ONBOARD: case BRD_ONBOARD32: case BRD_ONBOARD2: case BRD_ONBOARD2_32: case BRD_ONBOARDRS: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ONB_MEMSIZE; brdp->pagesize = ONB_ATPAGESIZE; brdp->init = stli_onbinit; brdp->enable = stli_onbenable; brdp->reenable = stli_onbenable; brdp->disable = stli_onbdisable; brdp->getmemptr = stli_onbgetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_onbreset; if (brdp->memaddr > 0x100000) brdp->enabval = ONB_MEMENABHI; else brdp->enabval = ONB_MEMENABLO; name = "serial(ONBoard)"; break; case BRD_ONBOARDE: brdp->membase = (void *) brdp->memaddr; brdp->memsize = ONB_EIMEMSIZE; brdp->pagesize = ONB_EIPAGESIZE; brdp->init = stli_onbeinit; brdp->enable = stli_onbeenable; brdp->reenable = stli_onbeenable; brdp->disable = stli_onbedisable; brdp->getmemptr = stli_onbegetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_onbereset; name = "serial(ONBoard/E)"; break; case BRD_BRUMBY4: case BRD_BRUMBY8: case BRD_BRUMBY16: brdp->membase = (void *) brdp->memaddr; brdp->memsize = BBY_MEMSIZE; brdp->pagesize = BBY_PAGESIZE; brdp->init = stli_bbyinit; brdp->enable = NULL; brdp->reenable = NULL; brdp->disable = NULL; brdp->getmemptr = stli_bbygetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_bbyreset; name = "serial(Brumby)"; break; case BRD_STALLION: brdp->membase = (void *) brdp->memaddr; brdp->memsize = STAL_MEMSIZE; brdp->pagesize = STAL_PAGESIZE; brdp->init = stli_stalinit; brdp->enable = NULL; brdp->reenable = NULL; brdp->disable = NULL; brdp->getmemptr = stli_stalgetmemptr; brdp->intr = stli_ecpintr; brdp->reset = stli_stalreset; name = "serial(Stallion)"; break; default: return(-EINVAL); } /* * The per-board operations structure is all set up, so now let's go * and get the board operational. Firstly initialize board configuration * registers. Set the memory mapping info so we can get at the boards * shared memory. */ EBRDINIT(brdp); brdp->membase = ioremap(brdp->memaddr, brdp->memsize); if (brdp->membase == (void *) NULL) return(-ENOMEM); /* * Now that all specific code is set up, enable the shared memory and * look for the a signature area that will tell us exactly what board * this is, and how many ports. */ EBRDENABLE(brdp); sigsp = (cdkonbsig_t *) EBRDGETMEMPTR(brdp, CDK_SIGADDR); memcpy(&sig, sigsp, sizeof(cdkonbsig_t)); EBRDDISABLE(brdp); #if 0 printk("%s(%d): sig-> magic=%x:%x:%x:%x romver=%x amask=%x:%x:%x\n", __FILE__, __LINE__, sig.magic0, sig.magic1, sig.magic2, sig.magic3, sig.romver, sig.amask0, sig.amask1, sig.amask2); #endif if ((sig.magic0 != ONB_MAGIC0) || (sig.magic1 != ONB_MAGIC1) || (sig.magic2 != ONB_MAGIC2) || (sig.magic3 != ONB_MAGIC3)) return(-ENODEV); /* * Scan through the signature alive mask and calculate how many ports * there are on this board. */ brdp->nrpanels = 1; if (sig.amask1) { brdp->nrports = 32; } else { for (i = 0; (i < 16); i++) { if (((sig.amask0 << i) & 0x8000) == 0) break; } brdp->nrports = i; } brdp->panels[0] = brdp->nrports; request_region(brdp->iobase, brdp->iosize, name); brdp->state |= BST_FOUND; return(0); } /*****************************************************************************/ /* * Start up a running board. This routine is only called after the * code has been down loaded to the board and is operational. It will * read in the memory map, and get the show on the road... */ static int stli_startbrd(stlibrd_t *brdp) { volatile cdkhdr_t *hdrp; volatile cdkmem_t *memp; volatile cdkasy_t *ap; unsigned long flags; stliport_t *portp; int portnr, nrdevs, i, rc; #if DEBUG printk(KERN_DEBUG "stli_startbrd(brdp=%x)\n", (int) brdp); #endif rc = 0; save_flags(flags); cli(); EBRDENABLE(brdp); hdrp = (volatile cdkhdr_t *) EBRDGETMEMPTR(brdp, CDK_CDKADDR); nrdevs = hdrp->nrdevs; #if 0 printk("%s(%d): CDK version %d.%d.%d --> " "nrdevs=%d memp=%x hostp=%x slavep=%x\n", __FILE__, __LINE__, hdrp->ver_release, hdrp->ver_modification, hdrp->ver_fix, nrdevs, (int) hdrp->memp, (int) hdrp->hostp, (int) hdrp->slavep); #endif if (nrdevs < (brdp->nrports + 1)) { printk(KERN_ERR "STALLION: slave failed to allocate memory for " "all devices, devices=%d\n", nrdevs); brdp->nrports = nrdevs - 1; } brdp->nrdevs = nrdevs; brdp->hostoffset = hdrp->hostp - CDK_CDKADDR; brdp->slaveoffset = hdrp->slavep - CDK_CDKADDR; brdp->bitsize = (nrdevs + 7) / 8; memp = (volatile cdkmem_t *) hdrp->memp; if (((unsigned long) memp) > brdp->memsize) { printk(KERN_ERR "STALLION: corrupted shared memory region?\n"); rc = -EIO; goto stli_donestartup; } memp = (volatile cdkmem_t *) EBRDGETMEMPTR(brdp, (unsigned long) memp); if (memp->dtype != TYP_ASYNCTRL) { printk(KERN_ERR "STALLION: no slave control device found\n"); goto stli_donestartup; } memp++; /* * Cycle through memory allocation of each port. We are guaranteed to * have all ports inside the first page of slave window, so no need to * change pages while reading memory map. */ for (i = 1, portnr = 0; (i < nrdevs); i++, portnr++, memp++) { if (memp->dtype != TYP_ASYNC) break; portp = brdp->ports[portnr]; if (portp == (stliport_t *) NULL) break; portp->devnr = i; portp->addr = memp->offset; portp->reqbit = (unsigned char) (0x1 << (i * 8 / nrdevs)); portp->portidx = (unsigned char) (i / 8); portp->portbit = (unsigned char) (0x1 << (i % 8)); } hdrp->slavereq = 0xff; /* * For each port setup a local copy of the RX and TX buffer offsets * and sizes. We do this separate from the above, because we need to * move the shared memory page... */ for (i = 1, portnr = 0; (i < nrdevs); i++, portnr++) { portp = brdp->ports[portnr]; if (portp == (stliport_t *) NULL) break; if (portp->addr == 0) break; ap = (volatile cdkasy_t *) EBRDGETMEMPTR(brdp, portp->addr); if (ap != (volatile cdkasy_t *) NULL) { portp->rxsize = ap->rxq.size; portp->txsize = ap->txq.size; portp->rxoffset = ap->rxq.offset; portp->txoffset = ap->txq.offset; } } stli_donestartup: EBRDDISABLE(brdp); restore_flags(flags); if (rc == 0) brdp->state |= BST_STARTED; if (! stli_timeron) { stli_timeron++; stli_timerlist.expires = STLI_TIMEOUT; add_timer(&stli_timerlist); } return(rc); } /*****************************************************************************/ /* * Probe and initialize the specified board. */ static int __init stli_brdinit(stlibrd_t *brdp) { #if DEBUG printk(KERN_DEBUG "stli_brdinit(brdp=%x)\n", (int) brdp); #endif stli_brds[brdp->brdnr] = brdp; switch (brdp->brdtype) { case BRD_ECP: case BRD_ECPE: case BRD_ECPMC: case BRD_ECPPCI: stli_initecp(brdp); break; case BRD_ONBOARD: case BRD_ONBOARDE: case BRD_ONBOARD2: case BRD_ONBOARD32: case BRD_ONBOARD2_32: case BRD_ONBOARDRS: case BRD_BRUMBY4: case BRD_BRUMBY8: case BRD_BRUMBY16: case BRD_STALLION: stli_initonb(brdp); break; case BRD_EASYIO: case BRD_ECH: case BRD_ECHMC: case BRD_ECHPCI: printk(KERN_ERR "STALLION: %s board type not supported in " "this driver\n", stli_brdnames[brdp->brdtype]); return(ENODEV); default: printk(KERN_ERR "STALLION: board=%d is unknown board " "type=%d\n", brdp->brdnr, brdp->brdtype); return(ENODEV); } if ((brdp->state & BST_FOUND) == 0) { printk(KERN_ERR "STALLION: %s board not found, board=%d " "io=%x mem=%x\n", stli_brdnames[brdp->brdtype], brdp->brdnr, brdp->iobase, (int) brdp->memaddr); return(ENODEV); } stli_initports(brdp); printk(KERN_INFO "STALLION: %s found, board=%d io=%x mem=%x " "nrpanels=%d nrports=%d\n", stli_brdnames[brdp->brdtype], brdp->brdnr, brdp->iobase, (int) brdp->memaddr, brdp->nrpanels, brdp->nrports); return(0); } /*****************************************************************************/ /* * Probe around trying to find where the EISA boards shared memory * might be. This is a bit if hack, but it is the best we can do. */ static inline int stli_eisamemprobe(stlibrd_t *brdp) { cdkecpsig_t ecpsig, *ecpsigp; cdkonbsig_t onbsig, *onbsigp; int i, foundit; #if DEBUG printk(KERN_DEBUG "stli_eisamemprobe(brdp=%x)\n", (int) brdp); #endif /* * First up we reset the board, to get it into a known state. There * is only 2 board types here we need to worry about. Don;t use the * standard board init routine here, it programs up the shared * memory address, and we don't know it yet... */ if (brdp->brdtype == BRD_ECPE) { outb(0x1, (brdp->iobase + ECP_EIBRDENAB)); outb(ECP_EISTOP, (brdp->iobase + ECP_EICONFR)); udelay(10); outb(ECP_EIDISABLE, (brdp->iobase + ECP_EICONFR)); udelay(500); stli_ecpeienable(brdp); } else if (brdp->brdtype == BRD_ONBOARDE) { outb(0x1, (brdp->iobase + ONB_EIBRDENAB)); outb(ONB_EISTOP, (brdp->iobase + ONB_EICONFR)); udelay(10); outb(ONB_EIDISABLE, (brdp->iobase + ONB_EICONFR)); mdelay(100); outb(0x1, brdp->iobase); mdelay(1); stli_onbeenable(brdp); } else { return(-ENODEV); } foundit = 0; brdp->memsize = ECP_MEMSIZE; /* * Board shared memory is enabled, so now we have a poke around and * see if we can find it. */ for (i = 0; (i < stli_eisamempsize); i++) { brdp->memaddr = stli_eisamemprobeaddrs[i]; brdp->membase = (void *) brdp->memaddr; brdp->membase = ioremap(brdp->memaddr, brdp->memsize); if (brdp->membase == (void *) NULL) continue; if (brdp->brdtype == BRD_ECPE) { ecpsigp = (cdkecpsig_t *) stli_ecpeigetmemptr(brdp, CDK_SIGADDR, __LINE__); memcpy(&ecpsig, ecpsigp, sizeof(cdkecpsig_t)); if (ecpsig.magic == ECP_MAGIC) foundit = 1; } else { onbsigp = (cdkonbsig_t *) stli_onbegetmemptr(brdp, CDK_SIGADDR, __LINE__); memcpy(&onbsig, onbsigp, sizeof(cdkonbsig_t)); if ((onbsig.magic0 == ONB_MAGIC0) && (onbsig.magic1 == ONB_MAGIC1) && (onbsig.magic2 == ONB_MAGIC2) && (onbsig.magic3 == ONB_MAGIC3)) foundit = 1; } iounmap(brdp->membase); if (foundit) break; } /* * Regardless of whether we found the shared memory or not we must * disable the region. After that return success or failure. */ if (brdp->brdtype == BRD_ECPE) stli_ecpeidisable(brdp); else stli_onbedisable(brdp); if (! foundit) { brdp->memaddr = 0; brdp->membase = 0; printk(KERN_ERR "STALLION: failed to probe shared memory " "region for %s in EISA slot=%d\n", stli_brdnames[brdp->brdtype], (brdp->iobase >> 12)); return(-ENODEV); } return(0); } /*****************************************************************************/ /* * Probe around and try to find any EISA boards in system. The biggest * problem here is finding out what memory address is associated with * an EISA board after it is found. The registers of the ECPE and * ONboardE are not readable - so we can't read them from there. We * don't have access to the EISA CMOS (or EISA BIOS) so we don't * actually have any way to find out the real value. The best we can * do is go probing around in the usual places hoping we can find it. */ static inline int stli_findeisabrds() { stlibrd_t *brdp; unsigned int iobase, eid; int i; #if DEBUG printk(KERN_DEBUG "stli_findeisabrds()\n"); #endif /* * Firstly check if this is an EISA system. Do this by probing for * the system board EISA ID. If this is not an EISA system then * don't bother going any further! */ outb(0xff, 0xc80); if (inb(0xc80) == 0xff) return(0); /* * Looks like an EISA system, so go searching for EISA boards. */ for (iobase = 0x1000; (iobase <= 0xc000); iobase += 0x1000) { outb(0xff, (iobase + 0xc80)); eid = inb(iobase + 0xc80); eid |= inb(iobase + 0xc81) << 8; if (eid != STL_EISAID) continue; /* * We have found a board. Need to check if this board was * statically configured already (just in case!). */ for (i = 0; (i < STL_MAXBRDS); i++) { brdp = stli_brds[i]; if (brdp == (stlibrd_t *) NULL) continue; if (brdp->iobase == iobase) break; } if (i < STL_MAXBRDS) continue; /* * We have found a Stallion board and it is not configured already. * Allocate a board structure and initialize it. */ if ((brdp = stli_allocbrd()) == (stlibrd_t *) NULL) return(-ENOMEM); if ((brdp->brdnr = stli_getbrdnr()) < 0) return(-ENOMEM); eid = inb(iobase + 0xc82); if (eid == ECP_EISAID) brdp->brdtype = BRD_ECPE; else if (eid == ONB_EISAID) brdp->brdtype = BRD_ONBOARDE; else brdp->brdtype = BRD_UNKNOWN; brdp->iobase = iobase; outb(0x1, (iobase + 0xc84)); if (stli_eisamemprobe(brdp)) outb(0, (iobase + 0xc84)); stli_brdinit(brdp); } return(0); } /*****************************************************************************/ /* * Find the next available board number that is free. */ static inline int stli_getbrdnr() { int i; for (i = 0; (i < STL_MAXBRDS); i++) { if (stli_brds[i] == (stlibrd_t *) NULL) { if (i >= stli_nrbrds) stli_nrbrds = i + 1; return(i); } } return(-1); } /*****************************************************************************/ #ifdef CONFIG_PCI /* * We have a Stallion board. Allocate a board structure and * initialize it. Read its IO and MEMORY resources from PCI * configuration space. */ static inline int stli_initpcibrd(int brdtype, struct pci_dev *devp) { stlibrd_t *brdp; #if DEBUG printk(KERN_DEBUG "stli_initpcibrd(brdtype=%d,busnr=%x,devnr=%x)\n", brdtype, dev->bus->number, dev->devfn); #endif if (pci_enable_device(devp)) return(-EIO); if ((brdp = stli_allocbrd()) == (stlibrd_t *) NULL) return(-ENOMEM); if ((brdp->brdnr = stli_getbrdnr()) < 0) { printk(KERN_INFO "STALLION: too many boards found, " "maximum supported %d\n", STL_MAXBRDS); return(0); } brdp->brdtype = brdtype; #if DEBUG printk(KERN_DEBUG "%s(%d): BAR[]=%lx,%lx,%lx,%lx\n", __FILE__, __LINE__, pci_resource_start(devp, 0), pci_resource_start(devp, 1), pci_resource_start(devp, 2), pci_resource_start(devp, 3)); #endif /* * We have all resources from the board, so lets setup the actual * board structure now. */ brdp->iobase = pci_resource_start(devp, 3); brdp->memaddr = pci_resource_start(devp, 2); stli_brdinit(brdp); return(0); } /*****************************************************************************/ /* * Find all Stallion PCI boards that might be installed. Initialize each * one as it is found. */ static inline int stli_findpcibrds() { struct pci_dev *dev = NULL; int rc; #if DEBUG printk("stli_findpcibrds()\n"); #endif if (! pci_present()) return(0); while ((dev = pci_find_device(PCI_VENDOR_ID_STALLION, PCI_DEVICE_ID_ECRA, dev))) { if ((rc = stli_initpcibrd(BRD_ECPPCI, dev))) return(rc); } return(0); } #endif /*****************************************************************************/ /* * Allocate a new board structure. Fill out the basic info in it. */ static stlibrd_t *stli_allocbrd() { stlibrd_t *brdp; brdp = (stlibrd_t *) stli_memalloc(sizeof(stlibrd_t)); if (brdp == (stlibrd_t *) NULL) { printk(KERN_ERR "STALLION: failed to allocate memory " "(size=%d)\n", sizeof(stlibrd_t)); return((stlibrd_t *) NULL); } memset(brdp, 0, sizeof(stlibrd_t)); brdp->magic = STLI_BOARDMAGIC; return(brdp); } /*****************************************************************************/ /* * Scan through all the boards in the configuration and see what we * can find. */ static inline int stli_initbrds() { stlibrd_t *brdp, *nxtbrdp; stlconf_t *confp; int i, j; #if DEBUG printk(KERN_DEBUG "stli_initbrds()\n"); #endif if (stli_nrbrds > STL_MAXBRDS) { printk(KERN_INFO "STALLION: too many boards in configuration " "table, truncating to %d\n", STL_MAXBRDS); stli_nrbrds = STL_MAXBRDS; } /* * Firstly scan the list of static boards configured. Allocate * resources and initialize the boards as found. If this is a * module then let the module args override static configuration. */ for (i = 0; (i < stli_nrbrds); i++) { confp = &stli_brdconf[i]; #ifdef MODULE stli_parsebrd(confp, stli_brdsp[i]); #endif if ((brdp = stli_allocbrd()) == (stlibrd_t *) NULL) return(-ENOMEM); brdp->brdnr = i; brdp->brdtype = confp->brdtype; brdp->iobase = confp->ioaddr1; brdp->memaddr = confp->memaddr; stli_brdinit(brdp); } /* * Static configuration table done, so now use dynamic methods to * see if any more boards should be configured. */ #ifdef MODULE stli_argbrds(); #endif if (stli_eisaprobe) stli_findeisabrds(); #ifdef CONFIG_PCI stli_findpcibrds(); #endif /* * All found boards are initialized. Now for a little optimization, if * no boards are sharing the "shared memory" regions then we can just * leave them all enabled. This is in fact the usual case. */ stli_shared = 0; if (stli_nrbrds > 1) { for (i = 0; (i < stli_nrbrds); i++) { brdp = stli_brds[i]; if (brdp == (stlibrd_t *) NULL) continue; for (j = i + 1; (j < stli_nrbrds); j++) { nxtbrdp = stli_brds[j]; if (nxtbrdp == (stlibrd_t *) NULL) continue; if ((brdp->membase >= nxtbrdp->membase) && (brdp->membase <= (nxtbrdp->membase + nxtbrdp->memsize - 1))) { stli_shared++; break; } } } } if (stli_shared == 0) { for (i = 0; (i < stli_nrbrds); i++) { brdp = stli_brds[i]; if (brdp == (stlibrd_t *) NULL) continue; if (brdp->state & BST_FOUND) { EBRDENABLE(brdp); brdp->enable = NULL; brdp->disable = NULL; } } } return(0); } /*****************************************************************************/ /* * Code to handle an "staliomem" read operation. This device is the * contents of the board shared memory. It is used for down loading * the slave image (and debugging :-) */ static ssize_t stli_memread(struct file *fp, char *buf, size_t count, loff_t *offp) { unsigned long flags; void *memptr; stlibrd_t *brdp; int brdnr, size, n; #if DEBUG printk(KERN_DEBUG "stli_memread(fp=%x,buf=%x,count=%x,offp=%x)\n", (int) fp, (int) buf, count, (int) offp); #endif brdnr = MINOR(fp->f_dentry->d_inode->i_rdev); if (brdnr >= stli_nrbrds) return(-ENODEV); brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (brdp->state == 0) return(-ENODEV); if (fp->f_pos >= brdp->memsize) return(0); size = MIN(count, (brdp->memsize - fp->f_pos)); save_flags(flags); cli(); EBRDENABLE(brdp); while (size > 0) { memptr = (void *) EBRDGETMEMPTR(brdp, fp->f_pos); n = MIN(size, (brdp->pagesize - (((unsigned long) fp->f_pos) % brdp->pagesize))); if (copy_to_user(buf, memptr, n)) { count = -EFAULT; goto out; } fp->f_pos += n; buf += n; size -= n; } out: EBRDDISABLE(brdp); restore_flags(flags); return(count); } /*****************************************************************************/ /* * Code to handle an "staliomem" write operation. This device is the * contents of the board shared memory. It is used for down loading * the slave image (and debugging :-) */ static ssize_t stli_memwrite(struct file *fp, const char *buf, size_t count, loff_t *offp) { unsigned long flags; void *memptr; stlibrd_t *brdp; char *chbuf; int brdnr, size, n; #if DEBUG printk(KERN_DEBUG "stli_memwrite(fp=%x,buf=%x,count=%x,offp=%x)\n", (int) fp, (int) buf, count, (int) offp); #endif brdnr = MINOR(fp->f_dentry->d_inode->i_rdev); if (brdnr >= stli_nrbrds) return(-ENODEV); brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (brdp->state == 0) return(-ENODEV); if (fp->f_pos >= brdp->memsize) return(0); chbuf = (char *) buf; size = MIN(count, (brdp->memsize - fp->f_pos)); save_flags(flags); cli(); EBRDENABLE(brdp); while (size > 0) { memptr = (void *) EBRDGETMEMPTR(brdp, fp->f_pos); n = MIN(size, (brdp->pagesize - (((unsigned long) fp->f_pos) % brdp->pagesize))); if (copy_from_user(memptr, chbuf, n)) { count = -EFAULT; goto out; } fp->f_pos += n; chbuf += n; size -= n; } out: EBRDDISABLE(brdp); restore_flags(flags); return(count); } /*****************************************************************************/ /* * Return the board stats structure to user app. */ static int stli_getbrdstats(combrd_t *bp) { stlibrd_t *brdp; int i; if (copy_from_user(&stli_brdstats, bp, sizeof(combrd_t))) return -EFAULT; if (stli_brdstats.brd >= STL_MAXBRDS) return(-ENODEV); brdp = stli_brds[stli_brdstats.brd]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); memset(&stli_brdstats, 0, sizeof(combrd_t)); stli_brdstats.brd = brdp->brdnr; stli_brdstats.type = brdp->brdtype; stli_brdstats.hwid = 0; stli_brdstats.state = brdp->state; stli_brdstats.ioaddr = brdp->iobase; stli_brdstats.memaddr = brdp->memaddr; stli_brdstats.nrpanels = brdp->nrpanels; stli_brdstats.nrports = brdp->nrports; for (i = 0; (i < brdp->nrpanels); i++) { stli_brdstats.panels[i].panel = i; stli_brdstats.panels[i].hwid = brdp->panelids[i]; stli_brdstats.panels[i].nrports = brdp->panels[i]; } if (copy_to_user(bp, &stli_brdstats, sizeof(combrd_t))) return -EFAULT; return(0); } /*****************************************************************************/ /* * Resolve the referenced port number into a port struct pointer. */ static stliport_t *stli_getport(int brdnr, int panelnr, int portnr) { stlibrd_t *brdp; int i; if ((brdnr < 0) || (brdnr >= STL_MAXBRDS)) return((stliport_t *) NULL); brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) return((stliport_t *) NULL); for (i = 0; (i < panelnr); i++) portnr += brdp->panels[i]; if ((portnr < 0) || (portnr >= brdp->nrports)) return((stliport_t *) NULL); return(brdp->ports[portnr]); } /*****************************************************************************/ /* * Return the port stats structure to user app. A NULL port struct * pointer passed in means that we need to find out from the app * what port to get stats for (used through board control device). */ static int stli_portcmdstats(stliport_t *portp) { unsigned long flags; stlibrd_t *brdp; int rc; memset(&stli_comstats, 0, sizeof(comstats_t)); if (portp == (stliport_t *) NULL) return(-ENODEV); brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (brdp->state & BST_STARTED) { if ((rc = stli_cmdwait(brdp, portp, A_GETSTATS, &stli_cdkstats, sizeof(asystats_t), 1)) < 0) return(rc); } else { memset(&stli_cdkstats, 0, sizeof(asystats_t)); } stli_comstats.brd = portp->brdnr; stli_comstats.panel = portp->panelnr; stli_comstats.port = portp->portnr; stli_comstats.state = portp->state; stli_comstats.flags = portp->flags; save_flags(flags); cli(); if (portp->tty != (struct tty_struct *) NULL) { if (portp->tty->driver_data == portp) { stli_comstats.ttystate = portp->tty->flags; stli_comstats.rxbuffered = portp->tty->flip.count; if (portp->tty->termios != (struct termios *) NULL) { stli_comstats.cflags = portp->tty->termios->c_cflag; stli_comstats.iflags = portp->tty->termios->c_iflag; stli_comstats.oflags = portp->tty->termios->c_oflag; stli_comstats.lflags = portp->tty->termios->c_lflag; } } } restore_flags(flags); stli_comstats.txtotal = stli_cdkstats.txchars; stli_comstats.rxtotal = stli_cdkstats.rxchars + stli_cdkstats.ringover; stli_comstats.txbuffered = stli_cdkstats.txringq; stli_comstats.rxbuffered += stli_cdkstats.rxringq; stli_comstats.rxoverrun = stli_cdkstats.overruns; stli_comstats.rxparity = stli_cdkstats.parity; stli_comstats.rxframing = stli_cdkstats.framing; stli_comstats.rxlost = stli_cdkstats.ringover; stli_comstats.rxbreaks = stli_cdkstats.rxbreaks; stli_comstats.txbreaks = stli_cdkstats.txbreaks; stli_comstats.txxon = stli_cdkstats.txstart; stli_comstats.txxoff = stli_cdkstats.txstop; stli_comstats.rxxon = stli_cdkstats.rxstart; stli_comstats.rxxoff = stli_cdkstats.rxstop; stli_comstats.rxrtsoff = stli_cdkstats.rtscnt / 2; stli_comstats.rxrtson = stli_cdkstats.rtscnt - stli_comstats.rxrtsoff; stli_comstats.modem = stli_cdkstats.dcdcnt; stli_comstats.hwid = stli_cdkstats.hwid; stli_comstats.signals = stli_mktiocm(stli_cdkstats.signals); return(0); } /*****************************************************************************/ /* * Return the port stats structure to user app. A NULL port struct * pointer passed in means that we need to find out from the app * what port to get stats for (used through board control device). */ static int stli_getportstats(stliport_t *portp, comstats_t *cp) { stlibrd_t *brdp; int rc; if (portp == (stliport_t *) NULL) { if (copy_from_user(&stli_comstats, cp, sizeof(comstats_t))) return -EFAULT; portp = stli_getport(stli_comstats.brd, stli_comstats.panel, stli_comstats.port); if (portp == (stliport_t *) NULL) return(-ENODEV); } brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if ((rc = stli_portcmdstats(portp)) < 0) return(rc); return copy_to_user(cp, &stli_comstats, sizeof(comstats_t)) ? -EFAULT : 0; } /*****************************************************************************/ /* * Clear the port stats structure. We also return it zeroed out... */ static int stli_clrportstats(stliport_t *portp, comstats_t *cp) { stlibrd_t *brdp; int rc; if (portp == (stliport_t *) NULL) { if (copy_from_user(&stli_comstats, cp, sizeof(comstats_t))) return -EFAULT; portp = stli_getport(stli_comstats.brd, stli_comstats.panel, stli_comstats.port); if (portp == (stliport_t *) NULL) return(-ENODEV); } brdp = stli_brds[portp->brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (brdp->state & BST_STARTED) { if ((rc = stli_cmdwait(brdp, portp, A_CLEARSTATS, 0, 0, 0)) < 0) return(rc); } memset(&stli_comstats, 0, sizeof(comstats_t)); stli_comstats.brd = portp->brdnr; stli_comstats.panel = portp->panelnr; stli_comstats.port = portp->portnr; if (copy_to_user(cp, &stli_comstats, sizeof(comstats_t))) return -EFAULT; return(0); } /*****************************************************************************/ /* * Return the entire driver ports structure to a user app. */ static int stli_getportstruct(unsigned long arg) { stliport_t *portp; if (copy_from_user(&stli_dummyport, (void *)arg, sizeof(stliport_t))) return -EFAULT; portp = stli_getport(stli_dummyport.brdnr, stli_dummyport.panelnr, stli_dummyport.portnr); if (portp == (stliport_t *) NULL) return(-ENODEV); if (copy_to_user((void *) arg, portp, sizeof(stliport_t))) return -EFAULT; return(0); } /*****************************************************************************/ /* * Return the entire driver board structure to a user app. */ static int stli_getbrdstruct(unsigned long arg) { stlibrd_t *brdp; if (copy_from_user(&stli_dummybrd, (void *)arg, sizeof(stlibrd_t))) return -EFAULT; if ((stli_dummybrd.brdnr < 0) || (stli_dummybrd.brdnr >= STL_MAXBRDS)) return(-ENODEV); brdp = stli_brds[stli_dummybrd.brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (copy_to_user((void *) arg, brdp, sizeof(stlibrd_t))) return -EFAULT; return(0); } /*****************************************************************************/ /* * The "staliomem" device is also required to do some special operations on * the board. We need to be able to send an interrupt to the board, * reset it, and start/stop it. */ static int stli_memioctl(struct inode *ip, struct file *fp, unsigned int cmd, unsigned long arg) { stlibrd_t *brdp; int brdnr, rc, done; #if DEBUG printk(KERN_DEBUG "stli_memioctl(ip=%x,fp=%x,cmd=%x,arg=%x)\n", (int) ip, (int) fp, cmd, (int) arg); #endif /* * First up handle the board independent ioctls. */ done = 0; rc = 0; switch (cmd) { case COM_GETPORTSTATS: rc = stli_getportstats((stliport_t *)NULL, (comstats_t *)arg); done++; break; case COM_CLRPORTSTATS: rc = stli_clrportstats((stliport_t *)NULL, (comstats_t *)arg); done++; break; case COM_GETBRDSTATS: rc = stli_getbrdstats((combrd_t *) arg); done++; break; case COM_READPORT: rc = stli_getportstruct(arg); done++; break; case COM_READBOARD: rc = stli_getbrdstruct(arg); done++; break; } if (done) return(rc); /* * Now handle the board specific ioctls. These all depend on the * minor number of the device they were called from. */ brdnr = MINOR(ip->i_rdev); if (brdnr >= STL_MAXBRDS) return(-ENODEV); brdp = stli_brds[brdnr]; if (brdp == (stlibrd_t *) NULL) return(-ENODEV); if (brdp->state == 0) return(-ENODEV); switch (cmd) { case STL_BINTR: EBRDINTR(brdp); break; case STL_BSTART: rc = stli_startbrd(brdp); break; case STL_BSTOP: brdp->state &= ~BST_STARTED; break; case STL_BRESET: brdp->state &= ~BST_STARTED; EBRDRESET(brdp); if (stli_shared == 0) { if (brdp->reenable != NULL) (* brdp->reenable)(brdp); } break; default: rc = -ENOIOCTLCMD; break; } return(rc); } /*****************************************************************************/ int __init stli_init(void) { printk(KERN_INFO "%s: version %s\n", stli_drvtitle, stli_drvversion); stli_initbrds(); /* * Allocate a temporary write buffer. */ stli_tmpwritebuf = (char *) stli_memalloc(STLI_TXBUFSIZE); if (stli_tmpwritebuf == (char *) NULL) printk(KERN_ERR "STALLION: failed to allocate memory " "(size=%d)\n", STLI_TXBUFSIZE); stli_txcookbuf = stli_memalloc(STLI_TXBUFSIZE); if (stli_txcookbuf == (char *) NULL) printk(KERN_ERR "STALLION: failed to allocate memory " "(size=%d)\n", STLI_TXBUFSIZE); /* * Set up a character driver for the shared memory region. We need this * to down load the slave code image. Also it is a useful debugging tool. */ if (devfs_register_chrdev(STL_SIOMEMMAJOR, "staliomem", &stli_fsiomem)) printk(KERN_ERR "STALLION: failed to register serial memory " "device\n"); devfs_handle = devfs_mk_dir (NULL, "staliomem", NULL); devfs_register_series (devfs_handle, "%u", 4, DEVFS_FL_DEFAULT, STL_SIOMEMMAJOR, 0, S_IFCHR | S_IRUSR | S_IWUSR, &stli_fsiomem, NULL); /* * Set up the tty driver structure and register us as a driver. * Also setup the callout tty device. */ memset(&stli_serial, 0, sizeof(struct tty_driver)); stli_serial.magic = TTY_DRIVER_MAGIC; stli_serial.driver_name = stli_drvname; stli_serial.name = stli_serialname; stli_serial.major = STL_SERIALMAJOR; stli_serial.minor_start = 0; stli_serial.num = STL_MAXBRDS * STL_MAXPORTS; stli_serial.type = TTY_DRIVER_TYPE_SERIAL; stli_serial.subtype = STL_DRVTYPSERIAL; stli_serial.init_termios = stli_deftermios; stli_serial.flags = TTY_DRIVER_REAL_RAW; stli_serial.refcount = &stli_refcount; stli_serial.table = stli_ttys; stli_serial.termios = stli_termios; stli_serial.termios_locked = stli_termioslocked; stli_serial.open = stli_open; stli_serial.close = stli_close; stli_serial.write = stli_write; stli_serial.put_char = stli_putchar; stli_serial.flush_chars = stli_flushchars; stli_serial.write_room = stli_writeroom; stli_serial.chars_in_buffer = stli_charsinbuffer; stli_serial.ioctl = stli_ioctl; stli_serial.set_termios = stli_settermios; stli_serial.throttle = stli_throttle; stli_serial.unthrottle = stli_unthrottle; stli_serial.stop = stli_stop; stli_serial.start = stli_start; stli_serial.hangup = stli_hangup; stli_serial.flush_buffer = stli_flushbuffer; stli_serial.break_ctl = stli_breakctl; stli_serial.wait_until_sent = stli_waituntilsent; stli_serial.send_xchar = stli_sendxchar; stli_serial.read_proc = stli_readproc; stli_callout = stli_serial; stli_callout.name = stli_calloutname; stli_callout.major = STL_CALLOUTMAJOR; stli_callout.subtype = STL_DRVTYPCALLOUT; stli_callout.read_proc = 0; if (tty_register_driver(&stli_serial)) printk(KERN_ERR "STALLION: failed to register serial driver\n"); if (tty_register_driver(&stli_callout)) printk(KERN_ERR "STALLION: failed to register callout driver\n"); return(0); } /*****************************************************************************/