URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [char/] [synclink.c] - Rev 1765
Compare with Previous | Blame | View Log
/* * linux/drivers/char/synclink.c * * $Id: synclink.c,v 1.1.1.1 2004-04-15 02:00:32 phoenix Exp $ * * Device driver for Microgate SyncLink ISA and PCI * high speed multiprotocol serial adapters. * * written by Paul Fulghum for Microgate Corporation * paulkf@microgate.com * * Microgate and SyncLink are trademarks of Microgate Corporation * * Derived from serial.c written by Theodore Ts'o and Linus Torvalds * * Original release 01/11/99 * * This code is released under the GNU General Public License (GPL) * * This driver is primarily intended for use in synchronous * HDLC mode. Asynchronous mode is also provided. * * When operating in synchronous mode, each call to mgsl_write() * contains exactly one complete HDLC frame. Calling mgsl_put_char * will start assembling an HDLC frame that will not be sent until * mgsl_flush_chars or mgsl_write is called. * * Synchronous receive data is reported as complete frames. To accomplish * this, the TTY flip buffer is bypassed (too small to hold largest * frame and may fragment frames) and the line discipline * receive entry point is called directly. * * This driver has been tested with a slightly modified ppp.c driver * for synchronous PPP. * * 2000/02/16 * Added interface for syncppp.c driver (an alternate synchronous PPP * implementation that also supports Cisco HDLC). Each device instance * registers as a tty device AND a network device (if dosyncppp option * is set for the device). The functionality is determined by which * device interface is opened. * * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED * OF THE POSSIBILITY OF SUCH DAMAGE. */ #define VERSION(ver,rel,seq) (((ver)<<16) | ((rel)<<8) | (seq)) #if defined(__i386__) # define BREAKPOINT() asm(" int $3"); #else # define BREAKPOINT() { } #endif #define MAX_ISA_DEVICES 10 #define MAX_PCI_DEVICES 10 #define MAX_TOTAL_DEVICES 20 #include <linux/config.h> #include <linux/module.h> #include <linux/version.h> #include <linux/errno.h> #include <linux/signal.h> #include <linux/sched.h> #include <linux/timer.h> #include <linux/interrupt.h> #include <linux/pci.h> #include <linux/tty.h> #include <linux/tty_flip.h> #include <linux/serial.h> #include <linux/major.h> #include <linux/string.h> #include <linux/fcntl.h> #include <linux/ptrace.h> #include <linux/ioport.h> #include <linux/mm.h> #include <linux/slab.h> #include <linux/netdevice.h> #include <linux/vmalloc.h> #include <linux/init.h> #include <asm/serial.h> #include <linux/delay.h> #include <linux/ioctl.h> #include <asm/system.h> #include <asm/io.h> #include <asm/irq.h> #include <asm/dma.h> #include <asm/bitops.h> #include <asm/types.h> #include <linux/termios.h> #include <linux/tqueue.h> #ifdef CONFIG_SYNCLINK_SYNCPPP_MODULE #define CONFIG_SYNCLINK_SYNCPPP 1 #endif #ifdef CONFIG_SYNCLINK_SYNCPPP #if LINUX_VERSION_CODE < VERSION(2,4,3) #include "../net/wan/syncppp.h" #else #include <net/syncppp.h> #endif #endif #include <asm/segment.h> #define GET_USER(error,value,addr) error = get_user(value,addr) #define COPY_FROM_USER(error,dest,src,size) error = copy_from_user(dest,src,size) ? -EFAULT : 0 #define PUT_USER(error,value,addr) error = put_user(value,addr) #define COPY_TO_USER(error,dest,src,size) error = copy_to_user(dest,src,size) ? -EFAULT : 0 #include <asm/uaccess.h> #include "linux/synclink.h" #define RCLRVALUE 0xffff MGSL_PARAMS default_params = { MGSL_MODE_HDLC, /* unsigned long mode */ 0, /* unsigned char loopback; */ HDLC_FLAG_UNDERRUN_ABORT15, /* unsigned short flags; */ HDLC_ENCODING_NRZI_SPACE, /* unsigned char encoding; */ 0, /* unsigned long clock_speed; */ 0xff, /* unsigned char addr_filter; */ HDLC_CRC_16_CCITT, /* unsigned short crc_type; */ HDLC_PREAMBLE_LENGTH_8BITS, /* unsigned char preamble_length; */ HDLC_PREAMBLE_PATTERN_NONE, /* unsigned char preamble; */ 9600, /* unsigned long data_rate; */ 8, /* unsigned char data_bits; */ 1, /* unsigned char stop_bits; */ ASYNC_PARITY_NONE /* unsigned char parity; */ }; #define SHARED_MEM_ADDRESS_SIZE 0x40000 #define BUFFERLISTSIZE (PAGE_SIZE) #define DMABUFFERSIZE (PAGE_SIZE) #define MAXRXFRAMES 7 typedef struct _DMABUFFERENTRY { u32 phys_addr; /* 32-bit flat physical address of data buffer */ u16 count; /* buffer size/data count */ u16 status; /* Control/status field */ u16 rcc; /* character count field */ u16 reserved; /* padding required by 16C32 */ u32 link; /* 32-bit flat link to next buffer entry */ char *virt_addr; /* virtual address of data buffer */ u32 phys_entry; /* physical address of this buffer entry */ } DMABUFFERENTRY, *DMAPBUFFERENTRY; /* The queue of BH actions to be performed */ #define BH_RECEIVE 1 #define BH_TRANSMIT 2 #define BH_STATUS 4 #define IO_PIN_SHUTDOWN_LIMIT 100 #define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK)) struct _input_signal_events { int ri_up; int ri_down; int dsr_up; int dsr_down; int dcd_up; int dcd_down; int cts_up; int cts_down; }; /* transmit holding buffer definitions*/ #define MAX_TX_HOLDING_BUFFERS 5 struct tx_holding_buffer { int buffer_size; unsigned char * buffer; }; /* * Device instance data structure */ struct mgsl_struct { void *if_ptr; /* General purpose pointer (used by SPPP) */ int magic; int flags; int count; /* count of opens */ int line; int hw_version; unsigned short close_delay; unsigned short closing_wait; /* time to wait before closing */ struct mgsl_icount icount; struct termios normal_termios; struct termios callout_termios; struct tty_struct *tty; int timeout; int x_char; /* xon/xoff character */ int blocked_open; /* # of blocked opens */ long session; /* Session of opening process */ long pgrp; /* pgrp of opening process */ u16 read_status_mask; u16 ignore_status_mask; unsigned char *xmit_buf; int xmit_head; int xmit_tail; int xmit_cnt; wait_queue_head_t open_wait; wait_queue_head_t close_wait; wait_queue_head_t status_event_wait_q; wait_queue_head_t event_wait_q; struct timer_list tx_timer; /* HDLC transmit timeout timer */ struct mgsl_struct *next_device; /* device list link */ spinlock_t irq_spinlock; /* spinlock for synchronizing with ISR */ struct tq_struct task; /* task structure for scheduling bh */ u32 EventMask; /* event trigger mask */ u32 RecordedEvents; /* pending events */ u32 max_frame_size; /* as set by device config */ u32 pending_bh; int bh_running; /* Protection from multiple */ int isr_overflow; int bh_requested; int dcd_chkcount; /* check counts to prevent */ int cts_chkcount; /* too many IRQs if a signal */ int dsr_chkcount; /* is floating */ int ri_chkcount; char *buffer_list; /* virtual address of Rx & Tx buffer lists */ unsigned long buffer_list_phys; unsigned int rx_buffer_count; /* count of total allocated Rx buffers */ DMABUFFERENTRY *rx_buffer_list; /* list of receive buffer entries */ unsigned int current_rx_buffer; int num_tx_dma_buffers; /* number of tx dma frames required */ int tx_dma_buffers_used; unsigned int tx_buffer_count; /* count of total allocated Tx buffers */ DMABUFFERENTRY *tx_buffer_list; /* list of transmit buffer entries */ int start_tx_dma_buffer; /* tx dma buffer to start tx dma operation */ int current_tx_buffer; /* next tx dma buffer to be loaded */ unsigned char *intermediate_rxbuffer; int num_tx_holding_buffers; /* number of tx holding buffer allocated */ int get_tx_holding_index; /* next tx holding buffer for adapter to load */ int put_tx_holding_index; /* next tx holding buffer to store user request */ int tx_holding_count; /* number of tx holding buffers waiting */ struct tx_holding_buffer tx_holding_buffers[MAX_TX_HOLDING_BUFFERS]; int rx_enabled; int rx_overflow; int rx_rcc_underrun; int tx_enabled; int tx_active; u32 idle_mode; u16 cmr_value; u16 tcsr_value; char device_name[25]; /* device instance name */ unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */ unsigned char bus; /* expansion bus number (zero based) */ unsigned char function; /* PCI device number */ unsigned int io_base; /* base I/O address of adapter */ unsigned int io_addr_size; /* size of the I/O address range */ int io_addr_requested; /* nonzero if I/O address requested */ unsigned int irq_level; /* interrupt level */ unsigned long irq_flags; int irq_requested; /* nonzero if IRQ requested */ unsigned int dma_level; /* DMA channel */ int dma_requested; /* nonzero if dma channel requested */ u16 mbre_bit; u16 loopback_bits; u16 usc_idle_mode; MGSL_PARAMS params; /* communications parameters */ unsigned char serial_signals; /* current serial signal states */ int irq_occurred; /* for diagnostics use */ unsigned int init_error; /* Initialization startup error (DIAGS) */ int fDiagnosticsmode; /* Driver in Diagnostic mode? (DIAGS) */ u32 last_mem_alloc; unsigned char* memory_base; /* shared memory address (PCI only) */ u32 phys_memory_base; int shared_mem_requested; unsigned char* lcr_base; /* local config registers (PCI only) */ u32 phys_lcr_base; u32 lcr_offset; int lcr_mem_requested; u32 misc_ctrl_value; char flag_buf[MAX_ASYNC_BUFFER_SIZE]; char char_buf[MAX_ASYNC_BUFFER_SIZE]; BOOLEAN drop_rts_on_tx_done; BOOLEAN loopmode_insert_requested; BOOLEAN loopmode_send_done_requested; struct _input_signal_events input_signal_events; /* SPPP/Cisco HDLC device parts */ int netcount; int dosyncppp; spinlock_t netlock; #ifdef CONFIG_SYNCLINK_SYNCPPP struct ppp_device pppdev; char netname[10]; struct net_device *netdev; struct net_device_stats netstats; struct net_device netdevice; #endif }; #define MGSL_MAGIC 0x5401 /* * The size of the serial xmit buffer is 1 page, or 4096 bytes */ #ifndef SERIAL_XMIT_SIZE #define SERIAL_XMIT_SIZE 4096 #endif /* * These macros define the offsets used in calculating the * I/O address of the specified USC registers. */ #define DCPIN 2 /* Bit 1 of I/O address */ #define SDPIN 4 /* Bit 2 of I/O address */ #define DCAR 0 /* DMA command/address register */ #define CCAR SDPIN /* channel command/address register */ #define DATAREG DCPIN + SDPIN /* serial data register */ #define MSBONLY 0x41 #define LSBONLY 0x40 /* * These macros define the register address (ordinal number) * used for writing address/value pairs to the USC. */ #define CMR 0x02 /* Channel mode Register */ #define CCSR 0x04 /* Channel Command/status Register */ #define CCR 0x06 /* Channel Control Register */ #define PSR 0x08 /* Port status Register */ #define PCR 0x0a /* Port Control Register */ #define TMDR 0x0c /* Test mode Data Register */ #define TMCR 0x0e /* Test mode Control Register */ #define CMCR 0x10 /* Clock mode Control Register */ #define HCR 0x12 /* Hardware Configuration Register */ #define IVR 0x14 /* Interrupt Vector Register */ #define IOCR 0x16 /* Input/Output Control Register */ #define ICR 0x18 /* Interrupt Control Register */ #define DCCR 0x1a /* Daisy Chain Control Register */ #define MISR 0x1c /* Misc Interrupt status Register */ #define SICR 0x1e /* status Interrupt Control Register */ #define RDR 0x20 /* Receive Data Register */ #define RMR 0x22 /* Receive mode Register */ #define RCSR 0x24 /* Receive Command/status Register */ #define RICR 0x26 /* Receive Interrupt Control Register */ #define RSR 0x28 /* Receive Sync Register */ #define RCLR 0x2a /* Receive count Limit Register */ #define RCCR 0x2c /* Receive Character count Register */ #define TC0R 0x2e /* Time Constant 0 Register */ #define TDR 0x30 /* Transmit Data Register */ #define TMR 0x32 /* Transmit mode Register */ #define TCSR 0x34 /* Transmit Command/status Register */ #define TICR 0x36 /* Transmit Interrupt Control Register */ #define TSR 0x38 /* Transmit Sync Register */ #define TCLR 0x3a /* Transmit count Limit Register */ #define TCCR 0x3c /* Transmit Character count Register */ #define TC1R 0x3e /* Time Constant 1 Register */ /* * MACRO DEFINITIONS FOR DMA REGISTERS */ #define DCR 0x06 /* DMA Control Register (shared) */ #define DACR 0x08 /* DMA Array count Register (shared) */ #define BDCR 0x12 /* Burst/Dwell Control Register (shared) */ #define DIVR 0x14 /* DMA Interrupt Vector Register (shared) */ #define DICR 0x18 /* DMA Interrupt Control Register (shared) */ #define CDIR 0x1a /* Clear DMA Interrupt Register (shared) */ #define SDIR 0x1c /* Set DMA Interrupt Register (shared) */ #define TDMR 0x02 /* Transmit DMA mode Register */ #define TDIAR 0x1e /* Transmit DMA Interrupt Arm Register */ #define TBCR 0x2a /* Transmit Byte count Register */ #define TARL 0x2c /* Transmit Address Register (low) */ #define TARU 0x2e /* Transmit Address Register (high) */ #define NTBCR 0x3a /* Next Transmit Byte count Register */ #define NTARL 0x3c /* Next Transmit Address Register (low) */ #define NTARU 0x3e /* Next Transmit Address Register (high) */ #define RDMR 0x82 /* Receive DMA mode Register (non-shared) */ #define RDIAR 0x9e /* Receive DMA Interrupt Arm Register */ #define RBCR 0xaa /* Receive Byte count Register */ #define RARL 0xac /* Receive Address Register (low) */ #define RARU 0xae /* Receive Address Register (high) */ #define NRBCR 0xba /* Next Receive Byte count Register */ #define NRARL 0xbc /* Next Receive Address Register (low) */ #define NRARU 0xbe /* Next Receive Address Register (high) */ /* * MACRO DEFINITIONS FOR MODEM STATUS BITS */ #define MODEMSTATUS_DTR 0x80 #define MODEMSTATUS_DSR 0x40 #define MODEMSTATUS_RTS 0x20 #define MODEMSTATUS_CTS 0x10 #define MODEMSTATUS_RI 0x04 #define MODEMSTATUS_DCD 0x01 /* * Channel Command/Address Register (CCAR) Command Codes */ #define RTCmd_Null 0x0000 #define RTCmd_ResetHighestIus 0x1000 #define RTCmd_TriggerChannelLoadDma 0x2000 #define RTCmd_TriggerRxDma 0x2800 #define RTCmd_TriggerTxDma 0x3000 #define RTCmd_TriggerRxAndTxDma 0x3800 #define RTCmd_PurgeRxFifo 0x4800 #define RTCmd_PurgeTxFifo 0x5000 #define RTCmd_PurgeRxAndTxFifo 0x5800 #define RTCmd_LoadRcc 0x6800 #define RTCmd_LoadTcc 0x7000 #define RTCmd_LoadRccAndTcc 0x7800 #define RTCmd_LoadTC0 0x8800 #define RTCmd_LoadTC1 0x9000 #define RTCmd_LoadTC0AndTC1 0x9800 #define RTCmd_SerialDataLSBFirst 0xa000 #define RTCmd_SerialDataMSBFirst 0xa800 #define RTCmd_SelectBigEndian 0xb000 #define RTCmd_SelectLittleEndian 0xb800 /* * DMA Command/Address Register (DCAR) Command Codes */ #define DmaCmd_Null 0x0000 #define DmaCmd_ResetTxChannel 0x1000 #define DmaCmd_ResetRxChannel 0x1200 #define DmaCmd_StartTxChannel 0x2000 #define DmaCmd_StartRxChannel 0x2200 #define DmaCmd_ContinueTxChannel 0x3000 #define DmaCmd_ContinueRxChannel 0x3200 #define DmaCmd_PauseTxChannel 0x4000 #define DmaCmd_PauseRxChannel 0x4200 #define DmaCmd_AbortTxChannel 0x5000 #define DmaCmd_AbortRxChannel 0x5200 #define DmaCmd_InitTxChannel 0x7000 #define DmaCmd_InitRxChannel 0x7200 #define DmaCmd_ResetHighestDmaIus 0x8000 #define DmaCmd_ResetAllChannels 0x9000 #define DmaCmd_StartAllChannels 0xa000 #define DmaCmd_ContinueAllChannels 0xb000 #define DmaCmd_PauseAllChannels 0xc000 #define DmaCmd_AbortAllChannels 0xd000 #define DmaCmd_InitAllChannels 0xf000 #define TCmd_Null 0x0000 #define TCmd_ClearTxCRC 0x2000 #define TCmd_SelectTicrTtsaData 0x4000 #define TCmd_SelectTicrTxFifostatus 0x5000 #define TCmd_SelectTicrIntLevel 0x6000 #define TCmd_SelectTicrdma_level 0x7000 #define TCmd_SendFrame 0x8000 #define TCmd_SendAbort 0x9000 #define TCmd_EnableDleInsertion 0xc000 #define TCmd_DisableDleInsertion 0xd000 #define TCmd_ClearEofEom 0xe000 #define TCmd_SetEofEom 0xf000 #define RCmd_Null 0x0000 #define RCmd_ClearRxCRC 0x2000 #define RCmd_EnterHuntmode 0x3000 #define RCmd_SelectRicrRtsaData 0x4000 #define RCmd_SelectRicrRxFifostatus 0x5000 #define RCmd_SelectRicrIntLevel 0x6000 #define RCmd_SelectRicrdma_level 0x7000 /* * Bits for enabling and disabling IRQs in Interrupt Control Register (ICR) */ #define RECEIVE_STATUS BIT5 #define RECEIVE_DATA BIT4 #define TRANSMIT_STATUS BIT3 #define TRANSMIT_DATA BIT2 #define IO_PIN BIT1 #define MISC BIT0 /* * Receive status Bits in Receive Command/status Register RCSR */ #define RXSTATUS_SHORT_FRAME BIT8 #define RXSTATUS_CODE_VIOLATION BIT8 #define RXSTATUS_EXITED_HUNT BIT7 #define RXSTATUS_IDLE_RECEIVED BIT6 #define RXSTATUS_BREAK_RECEIVED BIT5 #define RXSTATUS_ABORT_RECEIVED BIT5 #define RXSTATUS_RXBOUND BIT4 #define RXSTATUS_CRC_ERROR BIT3 #define RXSTATUS_FRAMING_ERROR BIT3 #define RXSTATUS_ABORT BIT2 #define RXSTATUS_PARITY_ERROR BIT2 #define RXSTATUS_OVERRUN BIT1 #define RXSTATUS_DATA_AVAILABLE BIT0 #define RXSTATUS_ALL 0x01f6 #define usc_UnlatchRxstatusBits(a,b) usc_OutReg( (a), RCSR, (u16)((b) & RXSTATUS_ALL) ) /* * Values for setting transmit idle mode in * Transmit Control/status Register (TCSR) */ #define IDLEMODE_FLAGS 0x0000 #define IDLEMODE_ALT_ONE_ZERO 0x0100 #define IDLEMODE_ZERO 0x0200 #define IDLEMODE_ONE 0x0300 #define IDLEMODE_ALT_MARK_SPACE 0x0500 #define IDLEMODE_SPACE 0x0600 #define IDLEMODE_MARK 0x0700 #define IDLEMODE_MASK 0x0700 /* * IUSC revision identifiers */ #define IUSC_SL1660 0x4d44 #define IUSC_PRE_SL1660 0x4553 /* * Transmit status Bits in Transmit Command/status Register (TCSR) */ #define TCSR_PRESERVE 0x0F00 #define TCSR_UNDERWAIT BIT11 #define TXSTATUS_PREAMBLE_SENT BIT7 #define TXSTATUS_IDLE_SENT BIT6 #define TXSTATUS_ABORT_SENT BIT5 #define TXSTATUS_EOF_SENT BIT4 #define TXSTATUS_EOM_SENT BIT4 #define TXSTATUS_CRC_SENT BIT3 #define TXSTATUS_ALL_SENT BIT2 #define TXSTATUS_UNDERRUN BIT1 #define TXSTATUS_FIFO_EMPTY BIT0 #define TXSTATUS_ALL 0x00fa #define usc_UnlatchTxstatusBits(a,b) usc_OutReg( (a), TCSR, (u16)((a)->tcsr_value + ((b) & 0x00FF)) ) #define MISCSTATUS_RXC_LATCHED BIT15 #define MISCSTATUS_RXC BIT14 #define MISCSTATUS_TXC_LATCHED BIT13 #define MISCSTATUS_TXC BIT12 #define MISCSTATUS_RI_LATCHED BIT11 #define MISCSTATUS_RI BIT10 #define MISCSTATUS_DSR_LATCHED BIT9 #define MISCSTATUS_DSR BIT8 #define MISCSTATUS_DCD_LATCHED BIT7 #define MISCSTATUS_DCD BIT6 #define MISCSTATUS_CTS_LATCHED BIT5 #define MISCSTATUS_CTS BIT4 #define MISCSTATUS_RCC_UNDERRUN BIT3 #define MISCSTATUS_DPLL_NO_SYNC BIT2 #define MISCSTATUS_BRG1_ZERO BIT1 #define MISCSTATUS_BRG0_ZERO BIT0 #define usc_UnlatchIostatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0xaaa0)) #define usc_UnlatchMiscstatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0x000f)) #define SICR_RXC_ACTIVE BIT15 #define SICR_RXC_INACTIVE BIT14 #define SICR_RXC (BIT15+BIT14) #define SICR_TXC_ACTIVE BIT13 #define SICR_TXC_INACTIVE BIT12 #define SICR_TXC (BIT13+BIT12) #define SICR_RI_ACTIVE BIT11 #define SICR_RI_INACTIVE BIT10 #define SICR_RI (BIT11+BIT10) #define SICR_DSR_ACTIVE BIT9 #define SICR_DSR_INACTIVE BIT8 #define SICR_DSR (BIT9+BIT8) #define SICR_DCD_ACTIVE BIT7 #define SICR_DCD_INACTIVE BIT6 #define SICR_DCD (BIT7+BIT6) #define SICR_CTS_ACTIVE BIT5 #define SICR_CTS_INACTIVE BIT4 #define SICR_CTS (BIT5+BIT4) #define SICR_RCC_UNDERFLOW BIT3 #define SICR_DPLL_NO_SYNC BIT2 #define SICR_BRG1_ZERO BIT1 #define SICR_BRG0_ZERO BIT0 void usc_DisableMasterIrqBit( struct mgsl_struct *info ); void usc_EnableMasterIrqBit( struct mgsl_struct *info ); void usc_EnableInterrupts( struct mgsl_struct *info, u16 IrqMask ); void usc_DisableInterrupts( struct mgsl_struct *info, u16 IrqMask ); void usc_ClearIrqPendingBits( struct mgsl_struct *info, u16 IrqMask ); #define usc_EnableInterrupts( a, b ) \ usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0xc0 + (b)) ) #define usc_DisableInterrupts( a, b ) \ usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0x80 + (b)) ) #define usc_EnableMasterIrqBit(a) \ usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0x0f00) + 0xb000) ) #define usc_DisableMasterIrqBit(a) \ usc_OutReg( (a), ICR, (u16)(usc_InReg((a),ICR) & 0x7f00) ) #define usc_ClearIrqPendingBits( a, b ) usc_OutReg( (a), DCCR, 0x40 + (b) ) /* * Transmit status Bits in Transmit Control status Register (TCSR) * and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0) */ #define TXSTATUS_PREAMBLE_SENT BIT7 #define TXSTATUS_IDLE_SENT BIT6 #define TXSTATUS_ABORT_SENT BIT5 #define TXSTATUS_EOF BIT4 #define TXSTATUS_CRC_SENT BIT3 #define TXSTATUS_ALL_SENT BIT2 #define TXSTATUS_UNDERRUN BIT1 #define TXSTATUS_FIFO_EMPTY BIT0 #define DICR_MASTER BIT15 #define DICR_TRANSMIT BIT0 #define DICR_RECEIVE BIT1 #define usc_EnableDmaInterrupts(a,b) \ usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) | (b)) ) #define usc_DisableDmaInterrupts(a,b) \ usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) & ~(b)) ) #define usc_EnableStatusIrqs(a,b) \ usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) | (b)) ) #define usc_DisablestatusIrqs(a,b) \ usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) & ~(b)) ) /* Transmit status Bits in Transmit Control status Register (TCSR) */ /* and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0) */ #define DISABLE_UNCONDITIONAL 0 #define DISABLE_END_OF_FRAME 1 #define ENABLE_UNCONDITIONAL 2 #define ENABLE_AUTO_CTS 3 #define ENABLE_AUTO_DCD 3 #define usc_EnableTransmitter(a,b) \ usc_OutReg( (a), TMR, (u16)((usc_InReg((a),TMR) & 0xfffc) | (b)) ) #define usc_EnableReceiver(a,b) \ usc_OutReg( (a), RMR, (u16)((usc_InReg((a),RMR) & 0xfffc) | (b)) ) u16 usc_InDmaReg( struct mgsl_struct *info, u16 Port ); void usc_OutDmaReg( struct mgsl_struct *info, u16 Port, u16 Value ); void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd ); u16 usc_InReg( struct mgsl_struct *info, u16 Port ); void usc_OutReg( struct mgsl_struct *info, u16 Port, u16 Value ); void usc_RTCmd( struct mgsl_struct *info, u16 Cmd ); void usc_RCmd( struct mgsl_struct *info, u16 Cmd ); void usc_TCmd( struct mgsl_struct *info, u16 Cmd ); #define usc_TCmd(a,b) usc_OutReg((a), TCSR, (u16)((a)->tcsr_value + (b))) #define usc_RCmd(a,b) usc_OutReg((a), RCSR, (b)) #define usc_SetTransmitSyncChars(a,s0,s1) usc_OutReg((a), TSR, (u16)(((u16)s0<<8)|(u16)s1)) void usc_process_rxoverrun_sync( struct mgsl_struct *info ); void usc_start_receiver( struct mgsl_struct *info ); void usc_stop_receiver( struct mgsl_struct *info ); void usc_start_transmitter( struct mgsl_struct *info ); void usc_stop_transmitter( struct mgsl_struct *info ); void usc_set_txidle( struct mgsl_struct *info ); void usc_load_txfifo( struct mgsl_struct *info ); void usc_enable_aux_clock( struct mgsl_struct *info, u32 DataRate ); void usc_enable_loopback( struct mgsl_struct *info, int enable ); void usc_get_serial_signals( struct mgsl_struct *info ); void usc_set_serial_signals( struct mgsl_struct *info ); void usc_reset( struct mgsl_struct *info ); void usc_set_sync_mode( struct mgsl_struct *info ); void usc_set_sdlc_mode( struct mgsl_struct *info ); void usc_set_async_mode( struct mgsl_struct *info ); void usc_enable_async_clock( struct mgsl_struct *info, u32 DataRate ); void usc_loopback_frame( struct mgsl_struct *info ); void mgsl_tx_timeout(unsigned long context); void usc_loopmode_cancel_transmit( struct mgsl_struct * info ); void usc_loopmode_insert_request( struct mgsl_struct * info ); int usc_loopmode_active( struct mgsl_struct * info); void usc_loopmode_send_done( struct mgsl_struct * info ); int usc_loopmode_send_active( struct mgsl_struct * info ); int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg); #ifdef CONFIG_SYNCLINK_SYNCPPP /* SPPP/HDLC stuff */ void mgsl_sppp_init(struct mgsl_struct *info); void mgsl_sppp_delete(struct mgsl_struct *info); int mgsl_sppp_open(struct net_device *d); int mgsl_sppp_close(struct net_device *d); void mgsl_sppp_tx_timeout(struct net_device *d); int mgsl_sppp_tx(struct sk_buff *skb, struct net_device *d); void mgsl_sppp_rx_done(struct mgsl_struct *info, char *buf, int size); void mgsl_sppp_tx_done(struct mgsl_struct *info); int mgsl_sppp_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd); struct net_device_stats *mgsl_net_stats(struct net_device *dev); #endif /* * Defines a BUS descriptor value for the PCI adapter * local bus address ranges. */ #define BUS_DESCRIPTOR( WrHold, WrDly, RdDly, Nwdd, Nwad, Nxda, Nrdd, Nrad ) \ (0x00400020 + \ ((WrHold) << 30) + \ ((WrDly) << 28) + \ ((RdDly) << 26) + \ ((Nwdd) << 20) + \ ((Nwad) << 15) + \ ((Nxda) << 13) + \ ((Nrdd) << 11) + \ ((Nrad) << 6) ) void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit); /* * Adapter diagnostic routines */ BOOLEAN mgsl_register_test( struct mgsl_struct *info ); BOOLEAN mgsl_irq_test( struct mgsl_struct *info ); BOOLEAN mgsl_dma_test( struct mgsl_struct *info ); BOOLEAN mgsl_memory_test( struct mgsl_struct *info ); int mgsl_adapter_test( struct mgsl_struct *info ); /* * device and resource management routines */ int mgsl_claim_resources(struct mgsl_struct *info); void mgsl_release_resources(struct mgsl_struct *info); void mgsl_add_device(struct mgsl_struct *info); struct mgsl_struct* mgsl_allocate_device(void); int mgsl_enum_isa_devices(void); /* * DMA buffer manupulation functions. */ void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex ); int mgsl_get_rx_frame( struct mgsl_struct *info ); int mgsl_get_raw_rx_frame( struct mgsl_struct *info ); void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info ); void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info ); int num_free_tx_dma_buffers(struct mgsl_struct *info); void mgsl_load_tx_dma_buffer( struct mgsl_struct *info, const char *Buffer, unsigned int BufferSize); void mgsl_load_pci_memory(char* TargetPtr, const char* SourcePtr, unsigned short count); /* * DMA and Shared Memory buffer allocation and formatting */ int mgsl_allocate_dma_buffers(struct mgsl_struct *info); void mgsl_free_dma_buffers(struct mgsl_struct *info); int mgsl_alloc_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount); void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount); int mgsl_alloc_buffer_list_memory(struct mgsl_struct *info); void mgsl_free_buffer_list_memory(struct mgsl_struct *info); int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info); void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info); int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info); void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info); int load_next_tx_holding_buffer(struct mgsl_struct *info); int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize); /* * Bottom half interrupt handlers */ void mgsl_bh_handler(void* Context); void mgsl_bh_receive(struct mgsl_struct *info); void mgsl_bh_transmit(struct mgsl_struct *info); void mgsl_bh_status(struct mgsl_struct *info); /* * Interrupt handler routines and dispatch table. */ void mgsl_isr_null( struct mgsl_struct *info ); void mgsl_isr_transmit_data( struct mgsl_struct *info ); void mgsl_isr_receive_data( struct mgsl_struct *info ); void mgsl_isr_receive_status( struct mgsl_struct *info ); void mgsl_isr_transmit_status( struct mgsl_struct *info ); void mgsl_isr_io_pin( struct mgsl_struct *info ); void mgsl_isr_misc( struct mgsl_struct *info ); void mgsl_isr_receive_dma( struct mgsl_struct *info ); void mgsl_isr_transmit_dma( struct mgsl_struct *info ); typedef void (*isr_dispatch_func)(struct mgsl_struct *); isr_dispatch_func UscIsrTable[7] = { mgsl_isr_null, mgsl_isr_misc, mgsl_isr_io_pin, mgsl_isr_transmit_data, mgsl_isr_transmit_status, mgsl_isr_receive_data, mgsl_isr_receive_status }; /* * ioctl call handlers */ static int set_modem_info(struct mgsl_struct * info, unsigned int cmd, unsigned int *value); static int get_modem_info(struct mgsl_struct * info, unsigned int *value); static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount *user_icount); static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS *user_params); static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS *new_params); static int mgsl_get_txidle(struct mgsl_struct * info, int*idle_mode); static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode); static int mgsl_txenable(struct mgsl_struct * info, int enable); static int mgsl_txabort(struct mgsl_struct * info); static int mgsl_rxenable(struct mgsl_struct * info, int enable); static int mgsl_wait_event(struct mgsl_struct * info, int * mask); static int mgsl_loopmode_send_done( struct mgsl_struct * info ); #define jiffies_from_ms(a) ((((a) * HZ)/1000)+1) /* * Global linked list of SyncLink devices */ struct mgsl_struct *mgsl_device_list; static int mgsl_device_count; /* * Set this param to non-zero to load eax with the * .text section address and breakpoint on module load. * This is useful for use with gdb and add-symbol-file command. */ static int break_on_load; /* * Driver major number, defaults to zero to get auto * assigned major number. May be forced as module parameter. */ static int ttymajor; static int cuamajor; /* * Array of user specified options for ISA adapters. */ static int io[MAX_ISA_DEVICES]; static int irq[MAX_ISA_DEVICES]; static int dma[MAX_ISA_DEVICES]; static int debug_level; static int maxframe[MAX_TOTAL_DEVICES]; static int dosyncppp[MAX_TOTAL_DEVICES]; static int txdmabufs[MAX_TOTAL_DEVICES]; static int txholdbufs[MAX_TOTAL_DEVICES]; MODULE_PARM(break_on_load,"i"); MODULE_PARM(ttymajor,"i"); MODULE_PARM(cuamajor,"i"); MODULE_PARM(io,"1-" __MODULE_STRING(MAX_ISA_DEVICES) "i"); MODULE_PARM(irq,"1-" __MODULE_STRING(MAX_ISA_DEVICES) "i"); MODULE_PARM(dma,"1-" __MODULE_STRING(MAX_ISA_DEVICES) "i"); MODULE_PARM(debug_level,"i"); MODULE_PARM(maxframe,"1-" __MODULE_STRING(MAX_TOTAL_DEVICES) "i"); MODULE_PARM(dosyncppp,"1-" __MODULE_STRING(MAX_TOTAL_DEVICES) "i"); MODULE_PARM(txdmabufs,"1-" __MODULE_STRING(MAX_TOTAL_DEVICES) "i"); MODULE_PARM(txholdbufs,"1-" __MODULE_STRING(MAX_TOTAL_DEVICES) "i"); static char *driver_name = "SyncLink serial driver"; static char *driver_version = "$Revision: 1.1.1.1 $"; static int __init synclink_init_one (struct pci_dev *dev, const struct pci_device_id *ent); static void __devexit synclink_remove_one (struct pci_dev *dev); static struct pci_device_id synclink_pci_tbl[] __devinitdata = { { PCI_VENDOR_ID_MICROGATE, PCI_DEVICE_ID_MICROGATE_USC, PCI_ANY_ID, PCI_ANY_ID, }, { PCI_VENDOR_ID_MICROGATE, 0x0210, PCI_ANY_ID, PCI_ANY_ID, }, { 0, }, /* terminate list */ }; MODULE_DEVICE_TABLE(pci, synclink_pci_tbl); #ifdef MODULE_LICENSE MODULE_LICENSE("GPL"); #endif static struct pci_driver synclink_pci_driver = { name: "synclink", id_table: synclink_pci_tbl, probe: synclink_init_one, remove: __devexit_p(synclink_remove_one), }; static struct tty_driver serial_driver, callout_driver; static int serial_refcount; /* number of characters left in xmit buffer before we ask for more */ #define WAKEUP_CHARS 256 static void mgsl_change_params(struct mgsl_struct *info); static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout); static struct tty_struct *serial_table[MAX_TOTAL_DEVICES]; static struct termios *serial_termios[MAX_TOTAL_DEVICES]; static struct termios *serial_termios_locked[MAX_TOTAL_DEVICES]; #ifndef MIN #define MIN(a,b) ((a) < (b) ? (a) : (b)) #endif /* * 1st function defined in .text section. Calling this function in * init_module() followed by a breakpoint allows a remote debugger * (gdb) to get the .text address for the add-symbol-file command. * This allows remote debugging of dynamically loadable modules. */ void* mgsl_get_text_ptr(void); void* mgsl_get_text_ptr() {return mgsl_get_text_ptr;} /* * tmp_buf is used as a temporary buffer by mgsl_write. We need to * lock it in case the COPY_FROM_USER blocks while swapping in a page, * and some other program tries to do a serial write at the same time. * Since the lock will only come under contention when the system is * swapping and available memory is low, it makes sense to share one * buffer across all the serial ioports, since it significantly saves * memory if large numbers of serial ports are open. */ static unsigned char *tmp_buf; static DECLARE_MUTEX(tmp_buf_sem); static inline int mgsl_paranoia_check(struct mgsl_struct *info, kdev_t device, const char *routine) { #ifdef MGSL_PARANOIA_CHECK static const char *badmagic = "Warning: bad magic number for mgsl struct (%s) in %s\n"; static const char *badinfo = "Warning: null mgsl_struct for (%s) in %s\n"; if (!info) { printk(badinfo, kdevname(device), routine); return 1; } if (info->magic != MGSL_MAGIC) { printk(badmagic, kdevname(device), routine); return 1; } #else if (!info) return 1; #endif return 0; } /* mgsl_stop() throttle (stop) transmitter * * Arguments: tty pointer to tty info structure * Return Value: None */ static void mgsl_stop(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (mgsl_paranoia_check(info, tty->device, "mgsl_stop")) return; if ( debug_level >= DEBUG_LEVEL_INFO ) printk("mgsl_stop(%s)\n",info->device_name); spin_lock_irqsave(&info->irq_spinlock,flags); if (info->tx_enabled) usc_stop_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* end of mgsl_stop() */ /* mgsl_start() release (start) transmitter * * Arguments: tty pointer to tty info structure * Return Value: None */ static void mgsl_start(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (mgsl_paranoia_check(info, tty->device, "mgsl_start")) return; if ( debug_level >= DEBUG_LEVEL_INFO ) printk("mgsl_start(%s)\n",info->device_name); spin_lock_irqsave(&info->irq_spinlock,flags); if (!info->tx_enabled) usc_start_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* end of mgsl_start() */ /* * Bottom half work queue access functions */ /* mgsl_bh_action() Return next bottom half action to perform. * Return Value: BH action code or 0 if nothing to do. */ int mgsl_bh_action(struct mgsl_struct *info) { unsigned long flags; int rc = 0; spin_lock_irqsave(&info->irq_spinlock,flags); if (info->pending_bh & BH_RECEIVE) { info->pending_bh &= ~BH_RECEIVE; rc = BH_RECEIVE; } else if (info->pending_bh & BH_TRANSMIT) { info->pending_bh &= ~BH_TRANSMIT; rc = BH_TRANSMIT; } else if (info->pending_bh & BH_STATUS) { info->pending_bh &= ~BH_STATUS; rc = BH_STATUS; } if (!rc) { /* Mark BH routine as complete */ info->bh_running = 0; info->bh_requested = 0; } spin_unlock_irqrestore(&info->irq_spinlock,flags); return rc; } /* * Perform bottom half processing of work items queued by ISR. */ void mgsl_bh_handler(void* Context) { struct mgsl_struct *info = (struct mgsl_struct*)Context; int action; if (!info) return; if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_handler(%s) entry\n", __FILE__,__LINE__,info->device_name); info->bh_running = 1; while((action = mgsl_bh_action(info)) != 0) { /* Process work item */ if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_handler() work item action=%d\n", __FILE__,__LINE__,action); switch (action) { case BH_RECEIVE: mgsl_bh_receive(info); break; case BH_TRANSMIT: mgsl_bh_transmit(info); break; case BH_STATUS: mgsl_bh_status(info); break; default: /* unknown work item ID */ printk("Unknown work item ID=%08X!\n", action); break; } } if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_handler(%s) exit\n", __FILE__,__LINE__,info->device_name); } void mgsl_bh_receive(struct mgsl_struct *info) { int (*get_rx_frame)(struct mgsl_struct *info) = (info->params.mode == MGSL_MODE_HDLC ? mgsl_get_rx_frame : mgsl_get_raw_rx_frame); if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_receive(%s)\n", __FILE__,__LINE__,info->device_name); do { if (info->rx_rcc_underrun) { unsigned long flags; spin_lock_irqsave(&info->irq_spinlock,flags); usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); return; } } while(get_rx_frame(info)); } void mgsl_bh_transmit(struct mgsl_struct *info) { struct tty_struct *tty = info->tty; unsigned long flags; if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_transmit() entry on %s\n", __FILE__,__LINE__,info->device_name); if (tty) { if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && tty->ldisc.write_wakeup) { if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):calling ldisc.write_wakeup on %s\n", __FILE__,__LINE__,info->device_name); (tty->ldisc.write_wakeup)(tty); } wake_up_interruptible(&tty->write_wait); } /* if transmitter idle and loopmode_send_done_requested * then start echoing RxD to TxD */ spin_lock_irqsave(&info->irq_spinlock,flags); if ( !info->tx_active && info->loopmode_send_done_requested ) usc_loopmode_send_done( info ); spin_unlock_irqrestore(&info->irq_spinlock,flags); } void mgsl_bh_status(struct mgsl_struct *info) { if ( debug_level >= DEBUG_LEVEL_BH ) printk( "%s(%d):mgsl_bh_status() entry on %s\n", __FILE__,__LINE__,info->device_name); info->ri_chkcount = 0; info->dsr_chkcount = 0; info->dcd_chkcount = 0; info->cts_chkcount = 0; } /* mgsl_isr_receive_status() * * Service a receive status interrupt. The type of status * interrupt is indicated by the state of the RCSR. * This is only used for HDLC mode. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_receive_status( struct mgsl_struct *info ) { u16 status = usc_InReg( info, RCSR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_receive_status status=%04X\n", __FILE__,__LINE__,status); if ( (status & RXSTATUS_ABORT_RECEIVED) && info->loopmode_insert_requested && usc_loopmode_active(info) ) { ++info->icount.rxabort; info->loopmode_insert_requested = FALSE; /* clear CMR:13 to start echoing RxD to TxD */ info->cmr_value &= ~BIT13; usc_OutReg(info, CMR, info->cmr_value); /* disable received abort irq (no longer required) */ usc_OutReg(info, RICR, (usc_InReg(info, RICR) & ~RXSTATUS_ABORT_RECEIVED)); } if (status & (RXSTATUS_EXITED_HUNT + RXSTATUS_IDLE_RECEIVED)) { if (status & RXSTATUS_EXITED_HUNT) info->icount.exithunt++; if (status & RXSTATUS_IDLE_RECEIVED) info->icount.rxidle++; wake_up_interruptible(&info->event_wait_q); } if (status & RXSTATUS_OVERRUN){ info->icount.rxover++; usc_process_rxoverrun_sync( info ); } usc_ClearIrqPendingBits( info, RECEIVE_STATUS ); usc_UnlatchRxstatusBits( info, status ); } /* end of mgsl_isr_receive_status() */ /* mgsl_isr_transmit_status() * * Service a transmit status interrupt * HDLC mode :end of transmit frame * Async mode:all data is sent * transmit status is indicated by bits in the TCSR. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_transmit_status( struct mgsl_struct *info ) { u16 status = usc_InReg( info, TCSR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_transmit_status status=%04X\n", __FILE__,__LINE__,status); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS ); usc_UnlatchTxstatusBits( info, status ); if ( status & (TXSTATUS_UNDERRUN | TXSTATUS_ABORT_SENT) ) { /* finished sending HDLC abort. This may leave */ /* the TxFifo with data from the aborted frame */ /* so purge the TxFifo. Also shutdown the DMA */ /* channel in case there is data remaining in */ /* the DMA buffer */ usc_DmaCmd( info, DmaCmd_ResetTxChannel ); usc_RTCmd( info, RTCmd_PurgeTxFifo ); } if ( status & TXSTATUS_EOF_SENT ) info->icount.txok++; else if ( status & TXSTATUS_UNDERRUN ) info->icount.txunder++; else if ( status & TXSTATUS_ABORT_SENT ) info->icount.txabort++; else info->icount.txunder++; info->tx_active = 0; info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; del_timer(&info->tx_timer); if ( info->drop_rts_on_tx_done ) { usc_get_serial_signals( info ); if ( info->serial_signals & SerialSignal_RTS ) { info->serial_signals &= ~SerialSignal_RTS; usc_set_serial_signals( info ); } info->drop_rts_on_tx_done = 0; } #ifdef CONFIG_SYNCLINK_SYNCPPP if (info->netcount) mgsl_sppp_tx_done(info); else #endif { if (info->tty->stopped || info->tty->hw_stopped) { usc_stop_transmitter(info); return; } info->pending_bh |= BH_TRANSMIT; } } /* end of mgsl_isr_transmit_status() */ /* mgsl_isr_io_pin() * * Service an Input/Output pin interrupt. The type of * interrupt is indicated by bits in the MISR * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_io_pin( struct mgsl_struct *info ) { struct mgsl_icount *icount; u16 status = usc_InReg( info, MISR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_io_pin status=%04X\n", __FILE__,__LINE__,status); usc_ClearIrqPendingBits( info, IO_PIN ); usc_UnlatchIostatusBits( info, status ); if (status & (MISCSTATUS_CTS_LATCHED | MISCSTATUS_DCD_LATCHED | MISCSTATUS_DSR_LATCHED | MISCSTATUS_RI_LATCHED) ) { icount = &info->icount; /* update input line counters */ if (status & MISCSTATUS_RI_LATCHED) { if ((info->ri_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT) usc_DisablestatusIrqs(info,SICR_RI); icount->rng++; if ( status & MISCSTATUS_RI ) info->input_signal_events.ri_up++; else info->input_signal_events.ri_down++; } if (status & MISCSTATUS_DSR_LATCHED) { if ((info->dsr_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT) usc_DisablestatusIrqs(info,SICR_DSR); icount->dsr++; if ( status & MISCSTATUS_DSR ) info->input_signal_events.dsr_up++; else info->input_signal_events.dsr_down++; } if (status & MISCSTATUS_DCD_LATCHED) { if ((info->dcd_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT) usc_DisablestatusIrqs(info,SICR_DCD); icount->dcd++; if (status & MISCSTATUS_DCD) { info->input_signal_events.dcd_up++; #ifdef CONFIG_SYNCLINK_SYNCPPP if (info->netcount) sppp_reopen(info->netdev); #endif } else info->input_signal_events.dcd_down++; } if (status & MISCSTATUS_CTS_LATCHED) { if ((info->cts_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT) usc_DisablestatusIrqs(info,SICR_CTS); icount->cts++; if ( status & MISCSTATUS_CTS ) info->input_signal_events.cts_up++; else info->input_signal_events.cts_down++; } wake_up_interruptible(&info->status_event_wait_q); wake_up_interruptible(&info->event_wait_q); if ( (info->flags & ASYNC_CHECK_CD) && (status & MISCSTATUS_DCD_LATCHED) ) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s CD now %s...", info->device_name, (status & MISCSTATUS_DCD) ? "on" : "off"); if (status & MISCSTATUS_DCD) wake_up_interruptible(&info->open_wait); else if (!((info->flags & ASYNC_CALLOUT_ACTIVE) && (info->flags & ASYNC_CALLOUT_NOHUP))) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("doing serial hangup..."); if (info->tty) tty_hangup(info->tty); } } if ( (info->flags & ASYNC_CTS_FLOW) && (status & MISCSTATUS_CTS_LATCHED) ) { if (info->tty->hw_stopped) { if (status & MISCSTATUS_CTS) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("CTS tx start..."); if (info->tty) info->tty->hw_stopped = 0; usc_start_transmitter(info); info->pending_bh |= BH_TRANSMIT; return; } } else { if (!(status & MISCSTATUS_CTS)) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("CTS tx stop..."); if (info->tty) info->tty->hw_stopped = 1; usc_stop_transmitter(info); } } } } info->pending_bh |= BH_STATUS; /* for diagnostics set IRQ flag */ if ( status & MISCSTATUS_TXC_LATCHED ){ usc_OutReg( info, SICR, (unsigned short)(usc_InReg(info,SICR) & ~(SICR_TXC_ACTIVE+SICR_TXC_INACTIVE)) ); usc_UnlatchIostatusBits( info, MISCSTATUS_TXC_LATCHED ); info->irq_occurred = 1; } } /* end of mgsl_isr_io_pin() */ /* mgsl_isr_transmit_data() * * Service a transmit data interrupt (async mode only). * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_transmit_data( struct mgsl_struct *info ) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_transmit_data xmit_cnt=%d\n", __FILE__,__LINE__,info->xmit_cnt); usc_ClearIrqPendingBits( info, TRANSMIT_DATA ); if (info->tty->stopped || info->tty->hw_stopped) { usc_stop_transmitter(info); return; } if ( info->xmit_cnt ) usc_load_txfifo( info ); else info->tx_active = 0; if (info->xmit_cnt < WAKEUP_CHARS) info->pending_bh |= BH_TRANSMIT; } /* end of mgsl_isr_transmit_data() */ /* mgsl_isr_receive_data() * * Service a receive data interrupt. This occurs * when operating in asynchronous interrupt transfer mode. * The receive data FIFO is flushed to the receive data buffers. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_receive_data( struct mgsl_struct *info ) { int Fifocount; u16 status; unsigned char DataByte; struct tty_struct *tty = info->tty; struct mgsl_icount *icount = &info->icount; if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_receive_data\n", __FILE__,__LINE__); usc_ClearIrqPendingBits( info, RECEIVE_DATA ); /* select FIFO status for RICR readback */ usc_RCmd( info, RCmd_SelectRicrRxFifostatus ); /* clear the Wordstatus bit so that status readback */ /* only reflects the status of this byte */ usc_OutReg( info, RICR+LSBONLY, (u16)(usc_InReg(info, RICR+LSBONLY) & ~BIT3 )); /* flush the receive FIFO */ while( (Fifocount = (usc_InReg(info,RICR) >> 8)) ) { /* read one byte from RxFIFO */ outw( (inw(info->io_base + CCAR) & 0x0780) | (RDR+LSBONLY), info->io_base + CCAR ); DataByte = inb( info->io_base + CCAR ); /* get the status of the received byte */ status = usc_InReg(info, RCSR); if ( status & (RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR + RXSTATUS_OVERRUN + RXSTATUS_BREAK_RECEIVED) ) usc_UnlatchRxstatusBits(info,RXSTATUS_ALL); if (tty->flip.count >= TTY_FLIPBUF_SIZE) continue; *tty->flip.char_buf_ptr = DataByte; icount->rx++; *tty->flip.flag_buf_ptr = 0; if ( status & (RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR + RXSTATUS_OVERRUN + RXSTATUS_BREAK_RECEIVED) ) { printk("rxerr=%04X\n",status); /* update error statistics */ if ( status & RXSTATUS_BREAK_RECEIVED ) { status &= ~(RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR); icount->brk++; } else if (status & RXSTATUS_PARITY_ERROR) icount->parity++; else if (status & RXSTATUS_FRAMING_ERROR) icount->frame++; else if (status & RXSTATUS_OVERRUN) { /* must issue purge fifo cmd before */ /* 16C32 accepts more receive chars */ usc_RTCmd(info,RTCmd_PurgeRxFifo); icount->overrun++; } /* discard char if tty control flags say so */ if (status & info->ignore_status_mask) continue; status &= info->read_status_mask; if (status & RXSTATUS_BREAK_RECEIVED) { *tty->flip.flag_buf_ptr = TTY_BREAK; if (info->flags & ASYNC_SAK) do_SAK(tty); } else if (status & RXSTATUS_PARITY_ERROR) *tty->flip.flag_buf_ptr = TTY_PARITY; else if (status & RXSTATUS_FRAMING_ERROR) *tty->flip.flag_buf_ptr = TTY_FRAME; if (status & RXSTATUS_OVERRUN) { /* Overrun is special, since it's * reported immediately, and doesn't * affect the current character */ if (tty->flip.count < TTY_FLIPBUF_SIZE) { tty->flip.count++; tty->flip.flag_buf_ptr++; tty->flip.char_buf_ptr++; *tty->flip.flag_buf_ptr = TTY_OVERRUN; } } } /* end of if (error) */ tty->flip.flag_buf_ptr++; tty->flip.char_buf_ptr++; tty->flip.count++; } if ( debug_level >= DEBUG_LEVEL_ISR ) { printk("%s(%d):mgsl_isr_receive_data flip count=%d\n", __FILE__,__LINE__,tty->flip.count); printk("%s(%d):rx=%d brk=%d parity=%d frame=%d overrun=%d\n", __FILE__,__LINE__,icount->rx,icount->brk, icount->parity,icount->frame,icount->overrun); } if ( tty->flip.count ) tty_flip_buffer_push(tty); } /* mgsl_isr_misc() * * Service a miscellaneos interrupt source. * * Arguments: info pointer to device extension (instance data) * Return Value: None */ void mgsl_isr_misc( struct mgsl_struct *info ) { u16 status = usc_InReg( info, MISR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_misc status=%04X\n", __FILE__,__LINE__,status); if ((status & MISCSTATUS_RCC_UNDERRUN) && (info->params.mode == MGSL_MODE_HDLC)) { /* turn off receiver and rx DMA */ usc_EnableReceiver(info,DISABLE_UNCONDITIONAL); usc_DmaCmd(info, DmaCmd_ResetRxChannel); usc_UnlatchRxstatusBits(info, RXSTATUS_ALL); usc_ClearIrqPendingBits(info, RECEIVE_DATA + RECEIVE_STATUS); usc_DisableInterrupts(info, RECEIVE_DATA + RECEIVE_STATUS); /* schedule BH handler to restart receiver */ info->pending_bh |= BH_RECEIVE; info->rx_rcc_underrun = 1; } usc_ClearIrqPendingBits( info, MISC ); usc_UnlatchMiscstatusBits( info, status ); } /* end of mgsl_isr_misc() */ /* mgsl_isr_null() * * Services undefined interrupt vectors from the * USC. (hence this function SHOULD never be called) * * Arguments: info pointer to device extension (instance data) * Return Value: None */ void mgsl_isr_null( struct mgsl_struct *info ) { } /* end of mgsl_isr_null() */ /* mgsl_isr_receive_dma() * * Service a receive DMA channel interrupt. * For this driver there are two sources of receive DMA interrupts * as identified in the Receive DMA mode Register (RDMR): * * BIT3 EOA/EOL End of List, all receive buffers in receive * buffer list have been filled (no more free buffers * available). The DMA controller has shut down. * * BIT2 EOB End of Buffer. This interrupt occurs when a receive * DMA buffer is terminated in response to completion * of a good frame or a frame with errors. The status * of the frame is stored in the buffer entry in the * list of receive buffer entries. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_receive_dma( struct mgsl_struct *info ) { u16 status; /* clear interrupt pending and IUS bit for Rx DMA IRQ */ usc_OutDmaReg( info, CDIR, BIT9+BIT1 ); /* Read the receive DMA status to identify interrupt type. */ /* This also clears the status bits. */ status = usc_InDmaReg( info, RDMR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_receive_dma(%s) status=%04X\n", __FILE__,__LINE__,info->device_name,status); info->pending_bh |= BH_RECEIVE; if ( status & BIT3 ) { info->rx_overflow = 1; info->icount.buf_overrun++; } } /* end of mgsl_isr_receive_dma() */ /* mgsl_isr_transmit_dma() * * This function services a transmit DMA channel interrupt. * * For this driver there is one source of transmit DMA interrupts * as identified in the Transmit DMA Mode Register (TDMR): * * BIT2 EOB End of Buffer. This interrupt occurs when a * transmit DMA buffer has been emptied. * * The driver maintains enough transmit DMA buffers to hold at least * one max frame size transmit frame. When operating in a buffered * transmit mode, there may be enough transmit DMA buffers to hold at * least two or more max frame size frames. On an EOB condition, * determine if there are any queued transmit buffers and copy into * transmit DMA buffers if we have room. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_isr_transmit_dma( struct mgsl_struct *info ) { u16 status; /* clear interrupt pending and IUS bit for Tx DMA IRQ */ usc_OutDmaReg(info, CDIR, BIT8+BIT0 ); /* Read the transmit DMA status to identify interrupt type. */ /* This also clears the status bits. */ status = usc_InDmaReg( info, TDMR ); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_isr_transmit_dma(%s) status=%04X\n", __FILE__,__LINE__,info->device_name,status); if ( status & BIT2 ) { --info->tx_dma_buffers_used; /* if there are transmit frames queued, * try to load the next one */ if ( load_next_tx_holding_buffer(info) ) { /* if call returns non-zero value, we have * at least one free tx holding buffer */ info->pending_bh |= BH_TRANSMIT; } } } /* end of mgsl_isr_transmit_dma() */ /* mgsl_interrupt() * * Interrupt service routine entry point. * * Arguments: * * irq interrupt number that caused interrupt * dev_id device ID supplied during interrupt registration * regs interrupted processor context * * Return Value: None */ static void mgsl_interrupt(int irq, void *dev_id, struct pt_regs * regs) { struct mgsl_struct * info; u16 UscVector; u16 DmaVector; if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_interrupt(%d)entry.\n", __FILE__,__LINE__,irq); info = (struct mgsl_struct *)dev_id; if (!info) return; spin_lock(&info->irq_spinlock); for(;;) { /* Read the interrupt vectors from hardware. */ UscVector = usc_InReg(info, IVR) >> 9; DmaVector = usc_InDmaReg(info, DIVR); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):%s UscVector=%08X DmaVector=%08X\n", __FILE__,__LINE__,info->device_name,UscVector,DmaVector); if ( !UscVector && !DmaVector ) break; /* Dispatch interrupt vector */ if ( UscVector ) (*UscIsrTable[UscVector])(info); else if ( (DmaVector&(BIT10|BIT9)) == BIT10) mgsl_isr_transmit_dma(info); else mgsl_isr_receive_dma(info); if ( info->isr_overflow ) { printk(KERN_ERR"%s(%d):%s isr overflow irq=%d\n", __FILE__,__LINE__,info->device_name, irq); usc_DisableMasterIrqBit(info); usc_DisableDmaInterrupts(info,DICR_MASTER); break; } } /* Request bottom half processing if there's something * for it to do and the bh is not already running */ if ( info->pending_bh && !info->bh_running && !info->bh_requested ) { if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):%s queueing bh task.\n", __FILE__,__LINE__,info->device_name); queue_task(&info->task, &tq_immediate); mark_bh(IMMEDIATE_BH); info->bh_requested = 1; } spin_unlock(&info->irq_spinlock); if ( debug_level >= DEBUG_LEVEL_ISR ) printk("%s(%d):mgsl_interrupt(%d)exit.\n", __FILE__,__LINE__,irq); } /* end of mgsl_interrupt() */ /* startup() * * Initialize and start device. * * Arguments: info pointer to device instance data * Return Value: 0 if success, otherwise error code */ static int startup(struct mgsl_struct * info) { int retval = 0; if ( debug_level >= DEBUG_LEVEL_INFO ) printk("%s(%d):mgsl_startup(%s)\n",__FILE__,__LINE__,info->device_name); if (info->flags & ASYNC_INITIALIZED) return 0; if (!info->xmit_buf) { /* allocate a page of memory for a transmit buffer */ info->xmit_buf = (unsigned char *)get_free_page(GFP_KERNEL); if (!info->xmit_buf) { printk(KERN_ERR"%s(%d):%s can't allocate transmit buffer\n", __FILE__,__LINE__,info->device_name); return -ENOMEM; } } info->pending_bh = 0; init_timer(&info->tx_timer); info->tx_timer.data = (unsigned long)info; info->tx_timer.function = mgsl_tx_timeout; /* Allocate and claim adapter resources */ retval = mgsl_claim_resources(info); /* perform existence check and diagnostics */ if ( !retval ) retval = mgsl_adapter_test(info); if ( retval ) { if (capable(CAP_SYS_ADMIN) && info->tty) set_bit(TTY_IO_ERROR, &info->tty->flags); mgsl_release_resources(info); return retval; } /* program hardware for current parameters */ mgsl_change_params(info); if (info->tty) clear_bit(TTY_IO_ERROR, &info->tty->flags); info->flags |= ASYNC_INITIALIZED; return 0; } /* end of startup() */ /* shutdown() * * Called by mgsl_close() and mgsl_hangup() to shutdown hardware * * Arguments: info pointer to device instance data * Return Value: None */ static void shutdown(struct mgsl_struct * info) { unsigned long flags; if (!(info->flags & ASYNC_INITIALIZED)) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_shutdown(%s)\n", __FILE__,__LINE__, info->device_name ); /* clear status wait queue because status changes */ /* can't happen after shutting down the hardware */ wake_up_interruptible(&info->status_event_wait_q); wake_up_interruptible(&info->event_wait_q); del_timer(&info->tx_timer); if (info->xmit_buf) { free_page((unsigned long) info->xmit_buf); info->xmit_buf = 0; } spin_lock_irqsave(&info->irq_spinlock,flags); usc_DisableMasterIrqBit(info); usc_stop_receiver(info); usc_stop_transmitter(info); usc_DisableInterrupts(info,RECEIVE_DATA + RECEIVE_STATUS + TRANSMIT_DATA + TRANSMIT_STATUS + IO_PIN + MISC ); usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE); /* Disable DMAEN (Port 7, Bit 14) */ /* This disconnects the DMA request signal from the ISA bus */ /* on the ISA adapter. This has no effect for the PCI adapter */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14)); /* Disable INTEN (Port 6, Bit12) */ /* This disconnects the IRQ request signal to the ISA bus */ /* on the ISA adapter. This has no effect for the PCI adapter */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12)); if (!info->tty || info->tty->termios->c_cflag & HUPCL) { info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS); usc_set_serial_signals(info); } spin_unlock_irqrestore(&info->irq_spinlock,flags); mgsl_release_resources(info); if (info->tty) set_bit(TTY_IO_ERROR, &info->tty->flags); info->flags &= ~ASYNC_INITIALIZED; } /* end of shutdown() */ static void mgsl_program_hw(struct mgsl_struct *info) { unsigned long flags; spin_lock_irqsave(&info->irq_spinlock,flags); usc_stop_receiver(info); usc_stop_transmitter(info); info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; if (info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW || info->netcount) usc_set_sync_mode(info); else usc_set_async_mode(info); usc_set_serial_signals(info); info->dcd_chkcount = 0; info->cts_chkcount = 0; info->ri_chkcount = 0; info->dsr_chkcount = 0; usc_EnableStatusIrqs(info,SICR_CTS+SICR_DSR+SICR_DCD+SICR_RI); usc_EnableInterrupts(info, IO_PIN); usc_get_serial_signals(info); if (info->netcount || info->tty->termios->c_cflag & CREAD) usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* Reconfigure adapter based on new parameters */ static void mgsl_change_params(struct mgsl_struct *info) { unsigned cflag; int bits_per_char; if (!info->tty || !info->tty->termios) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_change_params(%s)\n", __FILE__,__LINE__, info->device_name ); cflag = info->tty->termios->c_cflag; /* if B0 rate (hangup) specified then negate DTR and RTS */ /* otherwise assert DTR and RTS */ if (cflag & CBAUD) info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR; else info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR); /* byte size and parity */ switch (cflag & CSIZE) { case CS5: info->params.data_bits = 5; break; case CS6: info->params.data_bits = 6; break; case CS7: info->params.data_bits = 7; break; case CS8: info->params.data_bits = 8; break; /* Never happens, but GCC is too dumb to figure it out */ default: info->params.data_bits = 7; break; } if (cflag & CSTOPB) info->params.stop_bits = 2; else info->params.stop_bits = 1; info->params.parity = ASYNC_PARITY_NONE; if (cflag & PARENB) { if (cflag & PARODD) info->params.parity = ASYNC_PARITY_ODD; else info->params.parity = ASYNC_PARITY_EVEN; #ifdef CMSPAR if (cflag & CMSPAR) info->params.parity = ASYNC_PARITY_SPACE; #endif } /* calculate number of jiffies to transmit a full * FIFO (32 bytes) at specified data rate */ bits_per_char = info->params.data_bits + info->params.stop_bits + 1; /* if port data rate is set to 460800 or less then * allow tty settings to override, otherwise keep the * current data rate. */ if (info->params.data_rate <= 460800) info->params.data_rate = tty_get_baud_rate(info->tty); if ( info->params.data_rate ) { info->timeout = (32*HZ*bits_per_char) / info->params.data_rate; } info->timeout += HZ/50; /* Add .02 seconds of slop */ if (cflag & CRTSCTS) info->flags |= ASYNC_CTS_FLOW; else info->flags &= ~ASYNC_CTS_FLOW; if (cflag & CLOCAL) info->flags &= ~ASYNC_CHECK_CD; else info->flags |= ASYNC_CHECK_CD; /* process tty input control flags */ info->read_status_mask = RXSTATUS_OVERRUN; if (I_INPCK(info->tty)) info->read_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR; if (I_BRKINT(info->tty) || I_PARMRK(info->tty)) info->read_status_mask |= RXSTATUS_BREAK_RECEIVED; if (I_IGNPAR(info->tty)) info->ignore_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR; if (I_IGNBRK(info->tty)) { info->ignore_status_mask |= RXSTATUS_BREAK_RECEIVED; /* If ignoring parity and break indicators, ignore * overruns too. (For real raw support). */ if (I_IGNPAR(info->tty)) info->ignore_status_mask |= RXSTATUS_OVERRUN; } mgsl_program_hw(info); } /* end of mgsl_change_params() */ /* mgsl_put_char() * * Add a character to the transmit buffer. * * Arguments: tty pointer to tty information structure * ch character to add to transmit buffer * * Return Value: None */ static void mgsl_put_char(struct tty_struct *tty, unsigned char ch) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if ( debug_level >= DEBUG_LEVEL_INFO ) { printk( "%s(%d):mgsl_put_char(%d) on %s\n", __FILE__,__LINE__,ch,info->device_name); } if (mgsl_paranoia_check(info, tty->device, "mgsl_put_char")) return; if (!tty || !info->xmit_buf) return; spin_lock_irqsave(&info->irq_spinlock,flags); if ( (info->params.mode == MGSL_MODE_ASYNC ) || !info->tx_active ) { if (info->xmit_cnt < SERIAL_XMIT_SIZE - 1) { info->xmit_buf[info->xmit_head++] = ch; info->xmit_head &= SERIAL_XMIT_SIZE-1; info->xmit_cnt++; } } spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* end of mgsl_put_char() */ /* mgsl_flush_chars() * * Enable transmitter so remaining characters in the * transmit buffer are sent. * * Arguments: tty pointer to tty information structure * Return Value: None */ static void mgsl_flush_chars(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_flush_chars() entry on %s xmit_cnt=%d\n", __FILE__,__LINE__,info->device_name,info->xmit_cnt); if (mgsl_paranoia_check(info, tty->device, "mgsl_flush_chars")) return; if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || !info->xmit_buf) return; if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_flush_chars() entry on %s starting transmitter\n", __FILE__,__LINE__,info->device_name ); spin_lock_irqsave(&info->irq_spinlock,flags); if (!info->tx_active) { if ( (info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW) && info->xmit_cnt ) { /* operating in synchronous (frame oriented) mode */ /* copy data from circular xmit_buf to */ /* transmit DMA buffer. */ mgsl_load_tx_dma_buffer(info, info->xmit_buf,info->xmit_cnt); } usc_start_transmitter(info); } spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* end of mgsl_flush_chars() */ /* mgsl_write() * * Send a block of data * * Arguments: * * tty pointer to tty information structure * from_user flag: 1 = from user process * buf pointer to buffer containing send data * count size of send data in bytes * * Return Value: number of characters written */ static int mgsl_write(struct tty_struct * tty, int from_user, const unsigned char *buf, int count) { int c, ret = 0, err; struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) count=%d\n", __FILE__,__LINE__,info->device_name,count); if (mgsl_paranoia_check(info, tty->device, "mgsl_write")) goto cleanup; if (!tty || !info->xmit_buf || !tmp_buf) goto cleanup; if ( info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { /* operating in synchronous (frame oriented) mode */ /* operating in synchronous (frame oriented) mode */ if (info->tx_active) { if ( info->params.mode == MGSL_MODE_HDLC ) { ret = 0; goto cleanup; } /* transmitter is actively sending data - * if we have multiple transmit dma and * holding buffers, attempt to queue this * frame for transmission at a later time. */ if (info->tx_holding_count >= info->num_tx_holding_buffers ) { /* no tx holding buffers available */ ret = 0; goto cleanup; } /* queue transmit frame request */ ret = count; if (from_user) { down(&tmp_buf_sem); COPY_FROM_USER(err,tmp_buf, buf, count); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) sync user buf copy failed\n", __FILE__,__LINE__,info->device_name); ret = -EFAULT; } else save_tx_buffer_request(info,tmp_buf,count); up(&tmp_buf_sem); } else save_tx_buffer_request(info,buf,count); /* if we have sufficient tx dma buffers, * load the next buffered tx request */ spin_lock_irqsave(&info->irq_spinlock,flags); load_next_tx_holding_buffer(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); goto cleanup; } /* if operating in HDLC LoopMode and the adapter */ /* has yet to be inserted into the loop, we can't */ /* transmit */ if ( (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) && !usc_loopmode_active(info) ) { ret = 0; goto cleanup; } if ( info->xmit_cnt ) { /* Send accumulated from send_char() calls */ /* as frame and wait before accepting more data. */ ret = 0; /* copy data from circular xmit_buf to */ /* transmit DMA buffer. */ mgsl_load_tx_dma_buffer(info, info->xmit_buf,info->xmit_cnt); if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) sync xmit_cnt flushing\n", __FILE__,__LINE__,info->device_name); } else { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) sync transmit accepted\n", __FILE__,__LINE__,info->device_name); ret = count; info->xmit_cnt = count; if (from_user) { down(&tmp_buf_sem); COPY_FROM_USER(err,tmp_buf, buf, count); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) sync user buf copy failed\n", __FILE__,__LINE__,info->device_name); ret = -EFAULT; } else mgsl_load_tx_dma_buffer(info,tmp_buf,count); up(&tmp_buf_sem); } else mgsl_load_tx_dma_buffer(info,buf,count); } } else { if (from_user) { down(&tmp_buf_sem); while (1) { c = MIN(count, MIN(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, SERIAL_XMIT_SIZE - info->xmit_head)); if (c <= 0) break; COPY_FROM_USER(err,tmp_buf, buf, c); c -= err; if (!c) { if (!ret) ret = -EFAULT; break; } spin_lock_irqsave(&info->irq_spinlock,flags); c = MIN(c, MIN(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, SERIAL_XMIT_SIZE - info->xmit_head)); memcpy(info->xmit_buf + info->xmit_head, tmp_buf, c); info->xmit_head = ((info->xmit_head + c) & (SERIAL_XMIT_SIZE-1)); info->xmit_cnt += c; spin_unlock_irqrestore(&info->irq_spinlock,flags); buf += c; count -= c; ret += c; } up(&tmp_buf_sem); } else { while (1) { spin_lock_irqsave(&info->irq_spinlock,flags); c = MIN(count, MIN(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, SERIAL_XMIT_SIZE - info->xmit_head)); if (c <= 0) { spin_unlock_irqrestore(&info->irq_spinlock,flags); break; } memcpy(info->xmit_buf + info->xmit_head, buf, c); info->xmit_head = ((info->xmit_head + c) & (SERIAL_XMIT_SIZE-1)); info->xmit_cnt += c; spin_unlock_irqrestore(&info->irq_spinlock,flags); buf += c; count -= c; ret += c; } } } if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) { spin_lock_irqsave(&info->irq_spinlock,flags); if (!info->tx_active) usc_start_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } cleanup: if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_write(%s) returning=%d\n", __FILE__,__LINE__,info->device_name,ret); return ret; } /* end of mgsl_write() */ /* mgsl_write_room() * * Return the count of free bytes in transmit buffer * * Arguments: tty pointer to tty info structure * Return Value: None */ static int mgsl_write_room(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; int ret; if (mgsl_paranoia_check(info, tty->device, "mgsl_write_room")) return 0; ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; if (ret < 0) ret = 0; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_write_room(%s)=%d\n", __FILE__,__LINE__, info->device_name,ret ); if ( info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { /* operating in synchronous (frame oriented) mode */ if ( info->tx_active ) return 0; else return HDLC_MAX_FRAME_SIZE; } return ret; } /* end of mgsl_write_room() */ /* mgsl_chars_in_buffer() * * Return the count of bytes in transmit buffer * * Arguments: tty pointer to tty info structure * Return Value: None */ static int mgsl_chars_in_buffer(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_chars_in_buffer(%s)\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_chars_in_buffer")) return 0; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_chars_in_buffer(%s)=%d\n", __FILE__,__LINE__, info->device_name,info->xmit_cnt ); if ( info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { /* operating in synchronous (frame oriented) mode */ if ( info->tx_active ) return info->max_frame_size; else return 0; } return info->xmit_cnt; } /* end of mgsl_chars_in_buffer() */ /* mgsl_flush_buffer() * * Discard all data in the send buffer * * Arguments: tty pointer to tty info structure * Return Value: None */ static void mgsl_flush_buffer(struct tty_struct *tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_flush_buffer(%s) entry\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_flush_buffer")) return; spin_lock_irqsave(&info->irq_spinlock,flags); info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; del_timer(&info->tx_timer); spin_unlock_irqrestore(&info->irq_spinlock,flags); wake_up_interruptible(&tty->write_wait); if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && tty->ldisc.write_wakeup) (tty->ldisc.write_wakeup)(tty); } /* end of mgsl_flush_buffer() */ /* mgsl_send_xchar() * * Send a high-priority XON/XOFF character * * Arguments: tty pointer to tty info structure * ch character to send * Return Value: None */ static void mgsl_send_xchar(struct tty_struct *tty, char ch) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_send_xchar(%s,%d)\n", __FILE__,__LINE__, info->device_name, ch ); if (mgsl_paranoia_check(info, tty->device, "mgsl_send_xchar")) return; info->x_char = ch; if (ch) { /* Make sure transmit interrupts are on */ spin_lock_irqsave(&info->irq_spinlock,flags); if (!info->tx_enabled) usc_start_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } /* end of mgsl_send_xchar() */ /* mgsl_throttle() * * Signal remote device to throttle send data (our receive data) * * Arguments: tty pointer to tty info structure * Return Value: None */ static void mgsl_throttle(struct tty_struct * tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_throttle(%s) entry\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_throttle")) return; if (I_IXOFF(tty)) mgsl_send_xchar(tty, STOP_CHAR(tty)); if (tty->termios->c_cflag & CRTSCTS) { spin_lock_irqsave(&info->irq_spinlock,flags); info->serial_signals &= ~SerialSignal_RTS; usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } /* end of mgsl_throttle() */ /* mgsl_unthrottle() * * Signal remote device to stop throttling send data (our receive data) * * Arguments: tty pointer to tty info structure * Return Value: None */ static void mgsl_unthrottle(struct tty_struct * tty) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_unthrottle(%s) entry\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_unthrottle")) return; if (I_IXOFF(tty)) { if (info->x_char) info->x_char = 0; else mgsl_send_xchar(tty, START_CHAR(tty)); } if (tty->termios->c_cflag & CRTSCTS) { spin_lock_irqsave(&info->irq_spinlock,flags); info->serial_signals |= SerialSignal_RTS; usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } /* end of mgsl_unthrottle() */ /* mgsl_get_stats() * * get the current serial parameters information * * Arguments: info pointer to device instance data * user_icount pointer to buffer to hold returned stats * * Return Value: 0 if success, otherwise error code */ static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount *user_icount) { int err; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_get_params(%s)\n", __FILE__,__LINE__, info->device_name); COPY_TO_USER(err,user_icount, &info->icount, sizeof(struct mgsl_icount)); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_get_stats(%s) user buffer copy failed\n", __FILE__,__LINE__,info->device_name); return -EFAULT; } return 0; } /* end of mgsl_get_stats() */ /* mgsl_get_params() * * get the current serial parameters information * * Arguments: info pointer to device instance data * user_params pointer to buffer to hold returned params * * Return Value: 0 if success, otherwise error code */ static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS *user_params) { int err; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_get_params(%s)\n", __FILE__,__LINE__, info->device_name); COPY_TO_USER(err,user_params, &info->params, sizeof(MGSL_PARAMS)); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_get_params(%s) user buffer copy failed\n", __FILE__,__LINE__,info->device_name); return -EFAULT; } return 0; } /* end of mgsl_get_params() */ /* mgsl_set_params() * * set the serial parameters * * Arguments: * * info pointer to device instance data * new_params user buffer containing new serial params * * Return Value: 0 if success, otherwise error code */ static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS *new_params) { unsigned long flags; MGSL_PARAMS tmp_params; int err; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_set_params %s\n", __FILE__,__LINE__, info->device_name ); COPY_FROM_USER(err,&tmp_params, new_params, sizeof(MGSL_PARAMS)); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_set_params(%s) user buffer copy failed\n", __FILE__,__LINE__,info->device_name); return -EFAULT; } spin_lock_irqsave(&info->irq_spinlock,flags); memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS)); spin_unlock_irqrestore(&info->irq_spinlock,flags); mgsl_change_params(info); return 0; } /* end of mgsl_set_params() */ /* mgsl_get_txidle() * * get the current transmit idle mode * * Arguments: info pointer to device instance data * idle_mode pointer to buffer to hold returned idle mode * * Return Value: 0 if success, otherwise error code */ static int mgsl_get_txidle(struct mgsl_struct * info, int*idle_mode) { int err; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_get_txidle(%s)=%d\n", __FILE__,__LINE__, info->device_name, info->idle_mode); COPY_TO_USER(err,idle_mode, &info->idle_mode, sizeof(int)); if (err) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_get_txidle(%s) user buffer copy failed\n", __FILE__,__LINE__,info->device_name); return -EFAULT; } return 0; } /* end of mgsl_get_txidle() */ /* mgsl_set_txidle() service ioctl to set transmit idle mode * * Arguments: info pointer to device instance data * idle_mode new idle mode * * Return Value: 0 if success, otherwise error code */ static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode) { unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_set_txidle(%s,%d)\n", __FILE__,__LINE__, info->device_name, idle_mode ); spin_lock_irqsave(&info->irq_spinlock,flags); info->idle_mode = idle_mode; usc_set_txidle( info ); spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* end of mgsl_set_txidle() */ /* mgsl_txenable() * * enable or disable the transmitter * * Arguments: * * info pointer to device instance data * enable 1 = enable, 0 = disable * * Return Value: 0 if success, otherwise error code */ static int mgsl_txenable(struct mgsl_struct * info, int enable) { unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_txenable(%s,%d)\n", __FILE__,__LINE__, info->device_name, enable); spin_lock_irqsave(&info->irq_spinlock,flags); if ( enable ) { if ( !info->tx_enabled ) { usc_start_transmitter(info); /*-------------------------------------------------- * if HDLC/SDLC Loop mode, attempt to insert the * station in the 'loop' by setting CMR:13. Upon * receipt of the next GoAhead (RxAbort) sequence, * the OnLoop indicator (CCSR:7) should go active * to indicate that we are on the loop *--------------------------------------------------*/ if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE ) usc_loopmode_insert_request( info ); } } else { if ( info->tx_enabled ) usc_stop_transmitter(info); } spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* end of mgsl_txenable() */ /* mgsl_txabort() abort send HDLC frame * * Arguments: info pointer to device instance data * Return Value: 0 if success, otherwise error code */ static int mgsl_txabort(struct mgsl_struct * info) { unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_txabort(%s)\n", __FILE__,__LINE__, info->device_name); spin_lock_irqsave(&info->irq_spinlock,flags); if ( info->tx_active && info->params.mode == MGSL_MODE_HDLC ) { if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE ) usc_loopmode_cancel_transmit( info ); else usc_TCmd(info,TCmd_SendAbort); } spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* end of mgsl_txabort() */ /* mgsl_rxenable() enable or disable the receiver * * Arguments: info pointer to device instance data * enable 1 = enable, 0 = disable * Return Value: 0 if success, otherwise error code */ static int mgsl_rxenable(struct mgsl_struct * info, int enable) { unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_rxenable(%s,%d)\n", __FILE__,__LINE__, info->device_name, enable); spin_lock_irqsave(&info->irq_spinlock,flags); if ( enable ) { if ( !info->rx_enabled ) usc_start_receiver(info); } else { if ( info->rx_enabled ) usc_stop_receiver(info); } spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* end of mgsl_rxenable() */ /* mgsl_wait_event() wait for specified event to occur * * Arguments: info pointer to device instance data * mask pointer to bitmask of events to wait for * Return Value: 0 if successful and bit mask updated with * of events triggerred, * otherwise error code */ static int mgsl_wait_event(struct mgsl_struct * info, int * mask_ptr) { unsigned long flags; int s; int rc=0; struct mgsl_icount cprev, cnow; int events; int mask; struct _input_signal_events oldsigs, newsigs; DECLARE_WAITQUEUE(wait, current); COPY_FROM_USER(rc,&mask, mask_ptr, sizeof(int)); if (rc) { return -EFAULT; } if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_wait_event(%s,%d)\n", __FILE__,__LINE__, info->device_name, mask); spin_lock_irqsave(&info->irq_spinlock,flags); /* return immediately if state matches requested events */ usc_get_serial_signals(info); s = info->serial_signals; events = mask & ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) + ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) + ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) + ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) ); if (events) { spin_unlock_irqrestore(&info->irq_spinlock,flags); goto exit; } /* save current irq counts */ cprev = info->icount; oldsigs = info->input_signal_events; /* enable hunt and idle irqs if needed */ if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) { u16 oldreg = usc_InReg(info,RICR); u16 newreg = oldreg + (mask & MgslEvent_ExitHuntMode ? RXSTATUS_EXITED_HUNT:0) + (mask & MgslEvent_IdleReceived ? RXSTATUS_IDLE_RECEIVED:0); if (oldreg != newreg) usc_OutReg(info, RICR, newreg); } set_current_state(TASK_INTERRUPTIBLE); add_wait_queue(&info->event_wait_q, &wait); spin_unlock_irqrestore(&info->irq_spinlock,flags); for(;;) { schedule(); if (signal_pending(current)) { rc = -ERESTARTSYS; break; } /* get current irq counts */ spin_lock_irqsave(&info->irq_spinlock,flags); cnow = info->icount; newsigs = info->input_signal_events; set_current_state(TASK_INTERRUPTIBLE); spin_unlock_irqrestore(&info->irq_spinlock,flags); /* if no change, wait aborted for some reason */ if (newsigs.dsr_up == oldsigs.dsr_up && newsigs.dsr_down == oldsigs.dsr_down && newsigs.dcd_up == oldsigs.dcd_up && newsigs.dcd_down == oldsigs.dcd_down && newsigs.cts_up == oldsigs.cts_up && newsigs.cts_down == oldsigs.cts_down && newsigs.ri_up == oldsigs.ri_up && newsigs.ri_down == oldsigs.ri_down && cnow.exithunt == cprev.exithunt && cnow.rxidle == cprev.rxidle) { rc = -EIO; break; } events = mask & ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) + (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) + (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) + (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) + (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) + (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) + (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) + (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) + (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) + (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) ); if (events) break; cprev = cnow; oldsigs = newsigs; } remove_wait_queue(&info->event_wait_q, &wait); set_current_state(TASK_RUNNING); if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) { spin_lock_irqsave(&info->irq_spinlock,flags); if (!waitqueue_active(&info->event_wait_q)) { /* disable enable exit hunt mode/idle rcvd IRQs */ usc_OutReg(info, RICR, usc_InReg(info,RICR) & ~(RXSTATUS_EXITED_HUNT + RXSTATUS_IDLE_RECEIVED)); } spin_unlock_irqrestore(&info->irq_spinlock,flags); } exit: if ( rc == 0 ) PUT_USER(rc, events, mask_ptr); return rc; } /* end of mgsl_wait_event() */ static int modem_input_wait(struct mgsl_struct *info,int arg) { unsigned long flags; int rc; struct mgsl_icount cprev, cnow; DECLARE_WAITQUEUE(wait, current); /* save current irq counts */ spin_lock_irqsave(&info->irq_spinlock,flags); cprev = info->icount; add_wait_queue(&info->status_event_wait_q, &wait); set_current_state(TASK_INTERRUPTIBLE); spin_unlock_irqrestore(&info->irq_spinlock,flags); for(;;) { schedule(); if (signal_pending(current)) { rc = -ERESTARTSYS; break; } /* get new irq counts */ spin_lock_irqsave(&info->irq_spinlock,flags); cnow = info->icount; set_current_state(TASK_INTERRUPTIBLE); spin_unlock_irqrestore(&info->irq_spinlock,flags); /* if no change, wait aborted for some reason */ if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { rc = -EIO; break; } /* check for change in caller specified modem input */ if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) || (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) || (arg & TIOCM_CD && cnow.dcd != cprev.dcd) || (arg & TIOCM_CTS && cnow.cts != cprev.cts)) { rc = 0; break; } cprev = cnow; } remove_wait_queue(&info->status_event_wait_q, &wait); set_current_state(TASK_RUNNING); return rc; } /* get_modem_info() * * Read the state of the serial control and * status signals and return to caller. * * Arguments: info pointer to device instance data * value pointer to int to hold returned info * * Return Value: 0 if success, otherwise error code */ static int get_modem_info(struct mgsl_struct * info, unsigned int *value) { unsigned int result = 0; unsigned long flags; int err; spin_lock_irqsave(&info->irq_spinlock,flags); usc_get_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); if (info->serial_signals & SerialSignal_RTS) result |= TIOCM_RTS; if (info->serial_signals & SerialSignal_DTR) result |= TIOCM_DTR; if (info->serial_signals & SerialSignal_DCD) result |= TIOCM_CAR; if (info->serial_signals & SerialSignal_RI) result |= TIOCM_RNG; if (info->serial_signals & SerialSignal_DSR) result |= TIOCM_DSR; if (info->serial_signals & SerialSignal_CTS) result |= TIOCM_CTS; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_get_modem_info %s value=%08X\n", __FILE__,__LINE__, info->device_name, result ); PUT_USER(err,result,value); return err; } /* end of get_modem_info() */ /* set_modem_info() * * Set the state of the modem control signals (DTR/RTS) * * Arguments: * * info pointer to device instance data * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit * TIOCMSET = set/clear signal values * value bit mask for command * * Return Value: 0 if success, otherwise error code */ static int set_modem_info(struct mgsl_struct * info, unsigned int cmd, unsigned int *value) { int error; unsigned int arg; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_set_modem_info %s\n", __FILE__,__LINE__, info->device_name ); GET_USER(error,arg,value); if (error) return error; switch (cmd) { case TIOCMBIS: if (arg & TIOCM_RTS) info->serial_signals |= SerialSignal_RTS; if (arg & TIOCM_DTR) info->serial_signals |= SerialSignal_DTR; break; case TIOCMBIC: if (arg & TIOCM_RTS) info->serial_signals &= ~SerialSignal_RTS; if (arg & TIOCM_DTR) info->serial_signals &= ~SerialSignal_DTR; break; case TIOCMSET: if (arg & TIOCM_RTS) info->serial_signals |= SerialSignal_RTS; else info->serial_signals &= ~SerialSignal_RTS; if (arg & TIOCM_DTR) info->serial_signals |= SerialSignal_DTR; else info->serial_signals &= ~SerialSignal_DTR; break; default: return -EINVAL; } spin_lock_irqsave(&info->irq_spinlock,flags); usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* end of set_modem_info() */ /* mgsl_break() Set or clear transmit break condition * * Arguments: tty pointer to tty instance data * break_state -1=set break condition, 0=clear * Return Value: None */ static void mgsl_break(struct tty_struct *tty, int break_state) { struct mgsl_struct * info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_break(%s,%d)\n", __FILE__,__LINE__, info->device_name, break_state); if (mgsl_paranoia_check(info, tty->device, "mgsl_break")) return; spin_lock_irqsave(&info->irq_spinlock,flags); if (break_state == -1) usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) | BIT7)); else usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) & ~BIT7)); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* end of mgsl_break() */ /* mgsl_ioctl() Service an IOCTL request * * Arguments: * * tty pointer to tty instance data * file pointer to associated file object for device * cmd IOCTL command code * arg command argument/context * * Return Value: 0 if success, otherwise error code */ static int mgsl_ioctl(struct tty_struct *tty, struct file * file, unsigned int cmd, unsigned long arg) { struct mgsl_struct * info = (struct mgsl_struct *)tty->driver_data; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_ioctl %s cmd=%08X\n", __FILE__,__LINE__, info->device_name, cmd ); if (mgsl_paranoia_check(info, tty->device, "mgsl_ioctl")) return -ENODEV; if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { if (tty->flags & (1 << TTY_IO_ERROR)) return -EIO; } return mgsl_ioctl_common(info, cmd, arg); } int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg) { int error; struct mgsl_icount cnow; /* kernel counter temps */ struct serial_icounter_struct *p_cuser; /* user space */ unsigned long flags; switch (cmd) { case TIOCMGET: return get_modem_info(info, (unsigned int *) arg); case TIOCMBIS: case TIOCMBIC: case TIOCMSET: return set_modem_info(info, cmd, (unsigned int *) arg); case MGSL_IOCGPARAMS: return mgsl_get_params(info,(MGSL_PARAMS *)arg); case MGSL_IOCSPARAMS: return mgsl_set_params(info,(MGSL_PARAMS *)arg); case MGSL_IOCGTXIDLE: return mgsl_get_txidle(info,(int*)arg); case MGSL_IOCSTXIDLE: return mgsl_set_txidle(info,(int)arg); case MGSL_IOCTXENABLE: return mgsl_txenable(info,(int)arg); case MGSL_IOCRXENABLE: return mgsl_rxenable(info,(int)arg); case MGSL_IOCTXABORT: return mgsl_txabort(info); case MGSL_IOCGSTATS: return mgsl_get_stats(info,(struct mgsl_icount*)arg); case MGSL_IOCWAITEVENT: return mgsl_wait_event(info,(int*)arg); case MGSL_IOCLOOPTXDONE: return mgsl_loopmode_send_done(info); case MGSL_IOCCLRMODCOUNT: while(MOD_IN_USE) MOD_DEC_USE_COUNT; return 0; /* Wait for modem input (DCD,RI,DSR,CTS) change * as specified by mask in arg (TIOCM_RNG/DSR/CD/CTS) */ case TIOCMIWAIT: return modem_input_wait(info,(int)arg); /* * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) * Return: write counters to the user passed counter struct * NB: both 1->0 and 0->1 transitions are counted except for * RI where only 0->1 is counted. */ case TIOCGICOUNT: spin_lock_irqsave(&info->irq_spinlock,flags); cnow = info->icount; spin_unlock_irqrestore(&info->irq_spinlock,flags); p_cuser = (struct serial_icounter_struct *) arg; PUT_USER(error,cnow.cts, &p_cuser->cts); if (error) return error; PUT_USER(error,cnow.dsr, &p_cuser->dsr); if (error) return error; PUT_USER(error,cnow.rng, &p_cuser->rng); if (error) return error; PUT_USER(error,cnow.dcd, &p_cuser->dcd); if (error) return error; PUT_USER(error,cnow.rx, &p_cuser->rx); if (error) return error; PUT_USER(error,cnow.tx, &p_cuser->tx); if (error) return error; PUT_USER(error,cnow.frame, &p_cuser->frame); if (error) return error; PUT_USER(error,cnow.overrun, &p_cuser->overrun); if (error) return error; PUT_USER(error,cnow.parity, &p_cuser->parity); if (error) return error; PUT_USER(error,cnow.brk, &p_cuser->brk); if (error) return error; PUT_USER(error,cnow.buf_overrun, &p_cuser->buf_overrun); if (error) return error; return 0; default: return -ENOIOCTLCMD; } return 0; } /* mgsl_set_termios() * * Set new termios settings * * Arguments: * * tty pointer to tty structure * termios pointer to buffer to hold returned old termios * * Return Value: None */ static void mgsl_set_termios(struct tty_struct *tty, struct termios *old_termios) { struct mgsl_struct *info = (struct mgsl_struct *)tty->driver_data; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_set_termios %s\n", __FILE__,__LINE__, tty->driver.name ); /* just return if nothing has changed */ if ((tty->termios->c_cflag == old_termios->c_cflag) && (RELEVANT_IFLAG(tty->termios->c_iflag) == RELEVANT_IFLAG(old_termios->c_iflag))) return; mgsl_change_params(info); /* Handle transition to B0 status */ if (old_termios->c_cflag & CBAUD && !(tty->termios->c_cflag & CBAUD)) { info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR); spin_lock_irqsave(&info->irq_spinlock,flags); usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* Handle transition away from B0 status */ if (!(old_termios->c_cflag & CBAUD) && tty->termios->c_cflag & CBAUD) { info->serial_signals |= SerialSignal_DTR; if (!(tty->termios->c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->serial_signals |= SerialSignal_RTS; } spin_lock_irqsave(&info->irq_spinlock,flags); usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } /* Handle turning off CRTSCTS */ if (old_termios->c_cflag & CRTSCTS && !(tty->termios->c_cflag & CRTSCTS)) { tty->hw_stopped = 0; mgsl_start(tty); } } /* end of mgsl_set_termios() */ /* mgsl_close() * * Called when port is closed. Wait for remaining data to be * sent. Disable port and free resources. * * Arguments: * * tty pointer to open tty structure * filp pointer to open file object * * Return Value: None */ static void mgsl_close(struct tty_struct *tty, struct file * filp) { struct mgsl_struct * info = (struct mgsl_struct *)tty->driver_data; if (mgsl_paranoia_check(info, tty->device, "mgsl_close")) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_close(%s) entry, count=%d\n", __FILE__,__LINE__, info->device_name, info->count); if (!info->count) return; if (tty_hung_up_p(filp)) goto cleanup; if ((tty->count == 1) && (info->count != 1)) { /* * tty->count is 1 and the tty structure will be freed. * info->count should be one in this case. * if it's not, correct it so that the port is shutdown. */ printk("mgsl_close: bad refcount; tty->count is 1, " "info->count is %d\n", info->count); info->count = 1; } info->count--; /* if at least one open remaining, leave hardware active */ if (info->count) goto cleanup; info->flags |= ASYNC_CLOSING; /* Save the termios structure, since this port may have * separate termios for callout and dialin. */ if (info->flags & ASYNC_NORMAL_ACTIVE) info->normal_termios = *tty->termios; if (info->flags & ASYNC_CALLOUT_ACTIVE) info->callout_termios = *tty->termios; /* set tty->closing to notify line discipline to * only process XON/XOFF characters. Only the N_TTY * discipline appears to use this (ppp does not). */ tty->closing = 1; /* wait for transmit data to clear all layers */ if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) { if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_close(%s) calling tty_wait_until_sent\n", __FILE__,__LINE__, info->device_name ); tty_wait_until_sent(tty, info->closing_wait); } if (info->flags & ASYNC_INITIALIZED) mgsl_wait_until_sent(tty, info->timeout); if (tty->driver.flush_buffer) tty->driver.flush_buffer(tty); if (tty->ldisc.flush_buffer) tty->ldisc.flush_buffer(tty); shutdown(info); tty->closing = 0; info->tty = 0; if (info->blocked_open) { if (info->close_delay) { set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(info->close_delay); } wake_up_interruptible(&info->open_wait); } info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE| ASYNC_CLOSING); wake_up_interruptible(&info->close_wait); cleanup: if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_close(%s) exit, count=%d\n", __FILE__,__LINE__, tty->driver.name, info->count); if(MOD_IN_USE) MOD_DEC_USE_COUNT; } /* end of mgsl_close() */ /* mgsl_wait_until_sent() * * Wait until the transmitter is empty. * * Arguments: * * tty pointer to tty info structure * timeout time to wait for send completion * * Return Value: None */ static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout) { struct mgsl_struct * info = (struct mgsl_struct *)tty->driver_data; unsigned long orig_jiffies, char_time; if (!info ) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_wait_until_sent(%s) entry\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_wait_until_sent")) return; if (!(info->flags & ASYNC_INITIALIZED)) goto exit; orig_jiffies = jiffies; /* Set check interval to 1/5 of estimated time to * send a character, and make it at least 1. The check * interval should also be less than the timeout. * Note: use tight timings here to satisfy the NIST-PCTS. */ if ( info->params.data_rate ) { char_time = info->timeout/(32 * 5); if (!char_time) char_time++; } else char_time = 1; if (timeout) char_time = MIN(char_time, timeout); if ( info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { while (info->tx_active) { set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(char_time); if (signal_pending(current)) break; if (timeout && time_after(jiffies, orig_jiffies + timeout)) break; } } else { while (!(usc_InReg(info,TCSR) & TXSTATUS_ALL_SENT) && info->tx_enabled) { set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(char_time); if (signal_pending(current)) break; if (timeout && time_after(jiffies, orig_jiffies + timeout)) break; } } exit: if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_wait_until_sent(%s) exit\n", __FILE__,__LINE__, info->device_name ); } /* end of mgsl_wait_until_sent() */ /* mgsl_hangup() * * Called by tty_hangup() when a hangup is signaled. * This is the same as to closing all open files for the port. * * Arguments: tty pointer to associated tty object * Return Value: None */ static void mgsl_hangup(struct tty_struct *tty) { struct mgsl_struct * info = (struct mgsl_struct *)tty->driver_data; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_hangup(%s)\n", __FILE__,__LINE__, info->device_name ); if (mgsl_paranoia_check(info, tty->device, "mgsl_hangup")) return; mgsl_flush_buffer(tty); shutdown(info); info->count = 0; info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE); info->tty = 0; wake_up_interruptible(&info->open_wait); } /* end of mgsl_hangup() */ /* block_til_ready() * * Block the current process until the specified port * is ready to be opened. * * Arguments: * * tty pointer to tty info structure * filp pointer to open file object * info pointer to device instance data * * Return Value: 0 if success, otherwise error code */ static int block_til_ready(struct tty_struct *tty, struct file * filp, struct mgsl_struct *info) { DECLARE_WAITQUEUE(wait, current); int retval; int do_clocal = 0, extra_count = 0; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):block_til_ready on %s\n", __FILE__,__LINE__, tty->driver.name ); if (tty->driver.subtype == SERIAL_TYPE_CALLOUT) { /* this is a callout device */ /* just verify that normal device is not in use */ if (info->flags & ASYNC_NORMAL_ACTIVE) return -EBUSY; if ((info->flags & ASYNC_CALLOUT_ACTIVE) && (info->flags & ASYNC_SESSION_LOCKOUT) && (info->session != current->session)) return -EBUSY; if ((info->flags & ASYNC_CALLOUT_ACTIVE) && (info->flags & ASYNC_PGRP_LOCKOUT) && (info->pgrp != current->pgrp)) return -EBUSY; info->flags |= ASYNC_CALLOUT_ACTIVE; return 0; } if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){ /* nonblock mode is set or port is not enabled */ /* just verify that callout device is not active */ if (info->flags & ASYNC_CALLOUT_ACTIVE) return -EBUSY; info->flags |= ASYNC_NORMAL_ACTIVE; return 0; } if (info->flags & ASYNC_CALLOUT_ACTIVE) { if (info->normal_termios.c_cflag & CLOCAL) do_clocal = 1; } else { if (tty->termios->c_cflag & CLOCAL) do_clocal = 1; } /* Wait for carrier detect and the line to become * free (i.e., not in use by the callout). While we are in * this loop, info->count is dropped by one, so that * mgsl_close() knows when to free things. We restore it upon * exit, either normal or abnormal. */ retval = 0; add_wait_queue(&info->open_wait, &wait); if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):block_til_ready before block on %s count=%d\n", __FILE__,__LINE__, tty->driver.name, info->count ); save_flags(flags); cli(); if (!tty_hung_up_p(filp)) { extra_count = 1; info->count--; } restore_flags(flags); info->blocked_open++; while (1) { if (!(info->flags & ASYNC_CALLOUT_ACTIVE) && (tty->termios->c_cflag & CBAUD)) { spin_lock_irqsave(&info->irq_spinlock,flags); info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR; usc_set_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } set_current_state(TASK_INTERRUPTIBLE); if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){ retval = (info->flags & ASYNC_HUP_NOTIFY) ? -EAGAIN : -ERESTARTSYS; break; } spin_lock_irqsave(&info->irq_spinlock,flags); usc_get_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); if (!(info->flags & ASYNC_CALLOUT_ACTIVE) && !(info->flags & ASYNC_CLOSING) && (do_clocal || (info->serial_signals & SerialSignal_DCD)) ) { break; } if (signal_pending(current)) { retval = -ERESTARTSYS; break; } if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):block_til_ready blocking on %s count=%d\n", __FILE__,__LINE__, tty->driver.name, info->count ); schedule(); } set_current_state(TASK_RUNNING); remove_wait_queue(&info->open_wait, &wait); if (extra_count) info->count++; info->blocked_open--; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):block_til_ready after blocking on %s count=%d\n", __FILE__,__LINE__, tty->driver.name, info->count ); if (!retval) info->flags |= ASYNC_NORMAL_ACTIVE; return retval; } /* end of block_til_ready() */ /* mgsl_open() * * Called when a port is opened. Init and enable port. * Perform serial-specific initialization for the tty structure. * * Arguments: tty pointer to tty info structure * filp associated file pointer * * Return Value: 0 if success, otherwise error code */ static int mgsl_open(struct tty_struct *tty, struct file * filp) { struct mgsl_struct *info; int retval, line; unsigned long page; unsigned long flags; /* verify range of specified line number */ line = MINOR(tty->device) - tty->driver.minor_start; if ((line < 0) || (line >= mgsl_device_count)) { printk("%s(%d):mgsl_open with illegal line #%d.\n", __FILE__,__LINE__,line); return -ENODEV; } /* find the info structure for the specified line */ info = mgsl_device_list; while(info && info->line != line) info = info->next_device; if (mgsl_paranoia_check(info, tty->device, "mgsl_open")) return -ENODEV; tty->driver_data = info; info->tty = tty; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_open(%s), old ref count = %d\n", __FILE__,__LINE__,tty->driver.name, info->count); MOD_INC_USE_COUNT; /* If port is closing, signal caller to try again */ if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){ if (info->flags & ASYNC_CLOSING) interruptible_sleep_on(&info->close_wait); retval = ((info->flags & ASYNC_HUP_NOTIFY) ? -EAGAIN : -ERESTARTSYS); goto cleanup; } if (!tmp_buf) { page = get_free_page(GFP_KERNEL); if (!page) { retval = -ENOMEM; goto cleanup; } if (tmp_buf) free_page(page); else tmp_buf = (unsigned char *) page; } info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; spin_lock_irqsave(&info->netlock, flags); if (info->netcount) { retval = -EBUSY; spin_unlock_irqrestore(&info->netlock, flags); goto cleanup; } info->count++; spin_unlock_irqrestore(&info->netlock, flags); if (info->count == 1) { /* 1st open on this device, init hardware */ retval = startup(info); if (retval < 0) goto cleanup; } retval = block_til_ready(tty, filp, info); if (retval) { if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):block_til_ready(%s) returned %d\n", __FILE__,__LINE__, info->device_name, retval); goto cleanup; } if ((info->count == 1) && info->flags & ASYNC_SPLIT_TERMIOS) { if (tty->driver.subtype == SERIAL_TYPE_NORMAL) *tty->termios = info->normal_termios; else *tty->termios = info->callout_termios; mgsl_change_params(info); } info->session = current->session; info->pgrp = current->pgrp; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_open(%s) success\n", __FILE__,__LINE__, info->device_name); retval = 0; cleanup: if (retval) { if (tty->count == 1) info->tty = 0; /* tty layer will release tty struct */ if(MOD_IN_USE) MOD_DEC_USE_COUNT; if(info->count) info->count--; } return retval; } /* end of mgsl_open() */ /* * /proc fs routines.... */ static inline int line_info(char *buf, struct mgsl_struct *info) { char stat_buf[30]; int ret; unsigned long flags; if (info->bus_type == MGSL_BUS_TYPE_PCI) { ret = sprintf(buf, "%s:PCI io:%04X irq:%d mem:%08X lcr:%08X", info->device_name, info->io_base, info->irq_level, info->phys_memory_base, info->phys_lcr_base); } else { ret = sprintf(buf, "%s:(E)ISA io:%04X irq:%d dma:%d", info->device_name, info->io_base, info->irq_level, info->dma_level); } /* output current serial signal states */ spin_lock_irqsave(&info->irq_spinlock,flags); usc_get_serial_signals(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); stat_buf[0] = 0; stat_buf[1] = 0; if (info->serial_signals & SerialSignal_RTS) strcat(stat_buf, "|RTS"); if (info->serial_signals & SerialSignal_CTS) strcat(stat_buf, "|CTS"); if (info->serial_signals & SerialSignal_DTR) strcat(stat_buf, "|DTR"); if (info->serial_signals & SerialSignal_DSR) strcat(stat_buf, "|DSR"); if (info->serial_signals & SerialSignal_DCD) strcat(stat_buf, "|CD"); if (info->serial_signals & SerialSignal_RI) strcat(stat_buf, "|RI"); if (info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { ret += sprintf(buf+ret, " HDLC txok:%d rxok:%d", info->icount.txok, info->icount.rxok); if (info->icount.txunder) ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder); if (info->icount.txabort) ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort); if (info->icount.rxshort) ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort); if (info->icount.rxlong) ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong); if (info->icount.rxover) ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover); if (info->icount.rxcrc) ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc); } else { ret += sprintf(buf+ret, " ASYNC tx:%d rx:%d", info->icount.tx, info->icount.rx); if (info->icount.frame) ret += sprintf(buf+ret, " fe:%d", info->icount.frame); if (info->icount.parity) ret += sprintf(buf+ret, " pe:%d", info->icount.parity); if (info->icount.brk) ret += sprintf(buf+ret, " brk:%d", info->icount.brk); if (info->icount.overrun) ret += sprintf(buf+ret, " oe:%d", info->icount.overrun); } /* Append serial signal status to end */ ret += sprintf(buf+ret, " %s\n", stat_buf+1); ret += sprintf(buf+ret, "txactive=%d bh_req=%d bh_run=%d pending_bh=%x\n", info->tx_active,info->bh_requested,info->bh_running, info->pending_bh); spin_lock_irqsave(&info->irq_spinlock,flags); { u16 Tcsr = usc_InReg( info, TCSR ); u16 Tdmr = usc_InDmaReg( info, TDMR ); u16 Ticr = usc_InReg( info, TICR ); u16 Rscr = usc_InReg( info, RCSR ); u16 Rdmr = usc_InDmaReg( info, RDMR ); u16 Ricr = usc_InReg( info, RICR ); u16 Icr = usc_InReg( info, ICR ); u16 Dccr = usc_InReg( info, DCCR ); u16 Tmr = usc_InReg( info, TMR ); u16 Tccr = usc_InReg( info, TCCR ); u16 Ccar = inw( info->io_base + CCAR ); ret += sprintf(buf+ret, "tcsr=%04X tdmr=%04X ticr=%04X rcsr=%04X rdmr=%04X\n" "ricr=%04X icr =%04X dccr=%04X tmr=%04X tccr=%04X ccar=%04X\n", Tcsr,Tdmr,Ticr,Rscr,Rdmr,Ricr,Icr,Dccr,Tmr,Tccr,Ccar ); } spin_unlock_irqrestore(&info->irq_spinlock,flags); return ret; } /* end of line_info() */ /* mgsl_read_proc() * * Called to print information about devices * * Arguments: * page page of memory to hold returned info * start * off * count * eof * data * * Return Value: */ int mgsl_read_proc(char *page, char **start, off_t off, int count, int *eof, void *data) { int len = 0, l; off_t begin = 0; struct mgsl_struct *info; len += sprintf(page, "synclink driver:%s\n", driver_version); info = mgsl_device_list; while( info ) { l = line_info(page + len, info); len += l; if (len+begin > off+count) goto done; if (len+begin < off) { begin += len; len = 0; } info = info->next_device; } *eof = 1; done: if (off >= len+begin) return 0; *start = page + (off-begin); return ((count < begin+len-off) ? count : begin+len-off); } /* end of mgsl_read_proc() */ /* mgsl_allocate_dma_buffers() * * Allocate and format DMA buffers (ISA adapter) * or format shared memory buffers (PCI adapter). * * Arguments: info pointer to device instance data * Return Value: 0 if success, otherwise error */ int mgsl_allocate_dma_buffers(struct mgsl_struct *info) { unsigned short BuffersPerFrame; info->last_mem_alloc = 0; /* Calculate the number of DMA buffers necessary to hold the */ /* largest allowable frame size. Note: If the max frame size is */ /* not an even multiple of the DMA buffer size then we need to */ /* round the buffer count per frame up one. */ BuffersPerFrame = (unsigned short)(info->max_frame_size/DMABUFFERSIZE); if ( info->max_frame_size % DMABUFFERSIZE ) BuffersPerFrame++; if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { /* * The PCI adapter has 256KBytes of shared memory to use. * This is 64 PAGE_SIZE buffers. * * The first page is used for padding at this time so the * buffer list does not begin at offset 0 of the PCI * adapter's shared memory. * * The 2nd page is used for the buffer list. A 4K buffer * list can hold 128 DMA_BUFFER structures at 32 bytes * each. * * This leaves 62 4K pages. * * The next N pages are used for transmit frame(s). We * reserve enough 4K page blocks to hold the required * number of transmit dma buffers (num_tx_dma_buffers), * each of MaxFrameSize size. * * Of the remaining pages (62-N), determine how many can * be used to receive full MaxFrameSize inbound frames */ info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame; info->rx_buffer_count = 62 - info->tx_buffer_count; } else { /* Calculate the number of PAGE_SIZE buffers needed for */ /* receive and transmit DMA buffers. */ /* Calculate the number of DMA buffers necessary to */ /* hold 7 max size receive frames and one max size transmit frame. */ /* The receive buffer count is bumped by one so we avoid an */ /* End of List condition if all receive buffers are used when */ /* using linked list DMA buffers. */ info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame; info->rx_buffer_count = (BuffersPerFrame * MAXRXFRAMES) + 6; /* * limit total TxBuffers & RxBuffers to 62 4K total * (ala PCI Allocation) */ if ( (info->tx_buffer_count + info->rx_buffer_count) > 62 ) info->rx_buffer_count = 62 - info->tx_buffer_count; } if ( debug_level >= DEBUG_LEVEL_INFO ) printk("%s(%d):Allocating %d TX and %d RX DMA buffers.\n", __FILE__,__LINE__, info->tx_buffer_count,info->rx_buffer_count); if ( mgsl_alloc_buffer_list_memory( info ) < 0 || mgsl_alloc_frame_memory(info, info->rx_buffer_list, info->rx_buffer_count) < 0 || mgsl_alloc_frame_memory(info, info->tx_buffer_list, info->tx_buffer_count) < 0 || mgsl_alloc_intermediate_rxbuffer_memory(info) < 0 || mgsl_alloc_intermediate_txbuffer_memory(info) < 0 ) { printk("%s(%d):Can't allocate DMA buffer memory\n",__FILE__,__LINE__); return -ENOMEM; } mgsl_reset_rx_dma_buffers( info ); mgsl_reset_tx_dma_buffers( info ); return 0; } /* end of mgsl_allocate_dma_buffers() */ /* * mgsl_alloc_buffer_list_memory() * * Allocate a common DMA buffer for use as the * receive and transmit buffer lists. * * A buffer list is a set of buffer entries where each entry contains * a pointer to an actual buffer and a pointer to the next buffer entry * (plus some other info about the buffer). * * The buffer entries for a list are built to form a circular list so * that when the entire list has been traversed you start back at the * beginning. * * This function allocates memory for just the buffer entries. * The links (pointer to next entry) are filled in with the physical * address of the next entry so the adapter can navigate the list * using bus master DMA. The pointers to the actual buffers are filled * out later when the actual buffers are allocated. * * Arguments: info pointer to device instance data * Return Value: 0 if success, otherwise error */ int mgsl_alloc_buffer_list_memory( struct mgsl_struct *info ) { unsigned int i; if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { /* PCI adapter uses shared memory. */ info->buffer_list = info->memory_base + info->last_mem_alloc; info->buffer_list_phys = info->last_mem_alloc; info->last_mem_alloc += BUFFERLISTSIZE; } else { /* ISA adapter uses system memory. */ /* The buffer lists are allocated as a common buffer that both */ /* the processor and adapter can access. This allows the driver to */ /* inspect portions of the buffer while other portions are being */ /* updated by the adapter using Bus Master DMA. */ info->buffer_list = kmalloc(BUFFERLISTSIZE, GFP_KERNEL | GFP_DMA); if ( info->buffer_list == NULL ) return -ENOMEM; info->buffer_list_phys = virt_to_bus(info->buffer_list); } /* We got the memory for the buffer entry lists. */ /* Initialize the memory block to all zeros. */ memset( info->buffer_list, 0, BUFFERLISTSIZE ); /* Save virtual address pointers to the receive and */ /* transmit buffer lists. (Receive 1st). These pointers will */ /* be used by the processor to access the lists. */ info->rx_buffer_list = (DMABUFFERENTRY *)info->buffer_list; info->tx_buffer_list = (DMABUFFERENTRY *)info->buffer_list; info->tx_buffer_list += info->rx_buffer_count; /* * Build the links for the buffer entry lists such that * two circular lists are built. (Transmit and Receive). * * Note: the links are physical addresses * which are read by the adapter to determine the next * buffer entry to use. */ for ( i = 0; i < info->rx_buffer_count; i++ ) { /* calculate and store physical address of this buffer entry */ info->rx_buffer_list[i].phys_entry = info->buffer_list_phys + (i * sizeof(DMABUFFERENTRY)); /* calculate and store physical address of */ /* next entry in cirular list of entries */ info->rx_buffer_list[i].link = info->buffer_list_phys; if ( i < info->rx_buffer_count - 1 ) info->rx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY); } for ( i = 0; i < info->tx_buffer_count; i++ ) { /* calculate and store physical address of this buffer entry */ info->tx_buffer_list[i].phys_entry = info->buffer_list_phys + ((info->rx_buffer_count + i) * sizeof(DMABUFFERENTRY)); /* calculate and store physical address of */ /* next entry in cirular list of entries */ info->tx_buffer_list[i].link = info->buffer_list_phys + info->rx_buffer_count * sizeof(DMABUFFERENTRY); if ( i < info->tx_buffer_count - 1 ) info->tx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY); } return 0; } /* end of mgsl_alloc_buffer_list_memory() */ /* Free DMA buffers allocated for use as the * receive and transmit buffer lists. * Warning: * * The data transfer buffers associated with the buffer list * MUST be freed before freeing the buffer list itself because * the buffer list contains the information necessary to free * the individual buffers! */ void mgsl_free_buffer_list_memory( struct mgsl_struct *info ) { if ( info->buffer_list && info->bus_type != MGSL_BUS_TYPE_PCI ) kfree(info->buffer_list); info->buffer_list = NULL; info->rx_buffer_list = NULL; info->tx_buffer_list = NULL; } /* end of mgsl_free_buffer_list_memory() */ /* * mgsl_alloc_frame_memory() * * Allocate the frame DMA buffers used by the specified buffer list. * Each DMA buffer will be one memory page in size. This is necessary * because memory can fragment enough that it may be impossible * contiguous pages. * * Arguments: * * info pointer to device instance data * BufferList pointer to list of buffer entries * Buffercount count of buffer entries in buffer list * * Return Value: 0 if success, otherwise -ENOMEM */ int mgsl_alloc_frame_memory(struct mgsl_struct *info,DMABUFFERENTRY *BufferList,int Buffercount) { int i; unsigned long phys_addr; /* Allocate page sized buffers for the receive buffer list */ for ( i = 0; i < Buffercount; i++ ) { if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { /* PCI adapter uses shared memory buffers. */ BufferList[i].virt_addr = info->memory_base + info->last_mem_alloc; phys_addr = info->last_mem_alloc; info->last_mem_alloc += DMABUFFERSIZE; } else { /* ISA adapter uses system memory. */ BufferList[i].virt_addr = kmalloc(DMABUFFERSIZE, GFP_KERNEL | GFP_DMA); if ( BufferList[i].virt_addr == NULL ) return -ENOMEM; phys_addr = virt_to_bus(BufferList[i].virt_addr); } BufferList[i].phys_addr = phys_addr; } return 0; } /* end of mgsl_alloc_frame_memory() */ /* * mgsl_free_frame_memory() * * Free the buffers associated with * each buffer entry of a buffer list. * * Arguments: * * info pointer to device instance data * BufferList pointer to list of buffer entries * Buffercount count of buffer entries in buffer list * * Return Value: None */ void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList, int Buffercount) { int i; if ( BufferList ) { for ( i = 0 ; i < Buffercount ; i++ ) { if ( BufferList[i].virt_addr ) { if ( info->bus_type != MGSL_BUS_TYPE_PCI ) kfree(BufferList[i].virt_addr); BufferList[i].virt_addr = NULL; } } } } /* end of mgsl_free_frame_memory() */ /* mgsl_free_dma_buffers() * * Free DMA buffers * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_free_dma_buffers( struct mgsl_struct *info ) { mgsl_free_frame_memory( info, info->rx_buffer_list, info->rx_buffer_count ); mgsl_free_frame_memory( info, info->tx_buffer_list, info->tx_buffer_count ); mgsl_free_buffer_list_memory( info ); } /* end of mgsl_free_dma_buffers() */ /* * mgsl_alloc_intermediate_rxbuffer_memory() * * Allocate a buffer large enough to hold max_frame_size. This buffer * is used to pass an assembled frame to the line discipline. * * Arguments: * * info pointer to device instance data * * Return Value: 0 if success, otherwise -ENOMEM */ int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info) { info->intermediate_rxbuffer = kmalloc(info->max_frame_size, GFP_KERNEL | GFP_DMA); if ( info->intermediate_rxbuffer == NULL ) return -ENOMEM; return 0; } /* end of mgsl_alloc_intermediate_rxbuffer_memory() */ /* * mgsl_free_intermediate_rxbuffer_memory() * * * Arguments: * * info pointer to device instance data * * Return Value: None */ void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info) { if ( info->intermediate_rxbuffer ) kfree(info->intermediate_rxbuffer); info->intermediate_rxbuffer = NULL; } /* end of mgsl_free_intermediate_rxbuffer_memory() */ /* * mgsl_alloc_intermediate_txbuffer_memory() * * Allocate intermdiate transmit buffer(s) large enough to hold max_frame_size. * This buffer is used to load transmit frames into the adapter's dma transfer * buffers when there is sufficient space. * * Arguments: * * info pointer to device instance data * * Return Value: 0 if success, otherwise -ENOMEM */ int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info) { int i; if ( debug_level >= DEBUG_LEVEL_INFO ) printk("%s %s(%d) allocating %d tx holding buffers\n", info->device_name, __FILE__,__LINE__,info->num_tx_holding_buffers); memset(info->tx_holding_buffers,0,sizeof(info->tx_holding_buffers)); for ( i=0; i<info->num_tx_holding_buffers; ++i) { info->tx_holding_buffers[i].buffer = kmalloc(info->max_frame_size, GFP_KERNEL); if ( info->tx_holding_buffers[i].buffer == NULL ) return -ENOMEM; } return 0; } /* end of mgsl_alloc_intermediate_txbuffer_memory() */ /* * mgsl_free_intermediate_txbuffer_memory() * * * Arguments: * * info pointer to device instance data * * Return Value: None */ void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info) { int i; for ( i=0; i<info->num_tx_holding_buffers; ++i ) { if ( info->tx_holding_buffers[i].buffer ) { kfree(info->tx_holding_buffers[i].buffer); info->tx_holding_buffers[i].buffer=NULL; } } info->get_tx_holding_index = 0; info->put_tx_holding_index = 0; info->tx_holding_count = 0; } /* end of mgsl_free_intermediate_txbuffer_memory() */ /* * load_next_tx_holding_buffer() * * attempts to load the next buffered tx request into the * tx dma buffers * * Arguments: * * info pointer to device instance data * * Return Value: 1 if next buffered tx request loaded * into adapter's tx dma buffer, * 0 otherwise */ int load_next_tx_holding_buffer(struct mgsl_struct *info) { int ret = 0; if ( info->tx_holding_count ) { /* determine if we have enough tx dma buffers * to accomodate the next tx frame */ struct tx_holding_buffer *ptx = &info->tx_holding_buffers[info->get_tx_holding_index]; int num_free = num_free_tx_dma_buffers(info); int num_needed = ptx->buffer_size / DMABUFFERSIZE; if ( ptx->buffer_size % DMABUFFERSIZE ) ++num_needed; if (num_needed <= num_free) { info->xmit_cnt = ptx->buffer_size; mgsl_load_tx_dma_buffer(info,ptx->buffer,ptx->buffer_size); --info->tx_holding_count; if ( ++info->get_tx_holding_index >= info->num_tx_holding_buffers) info->get_tx_holding_index=0; /* restart transmit timer */ mod_timer(&info->tx_timer, jiffies + jiffies_from_ms(5000)); ret = 1; } } return ret; } /* * save_tx_buffer_request() * * attempt to store transmit frame request for later transmission * * Arguments: * * info pointer to device instance data * Buffer pointer to buffer containing frame to load * BufferSize size in bytes of frame in Buffer * * Return Value: 1 if able to store, 0 otherwise */ int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize) { struct tx_holding_buffer *ptx; if ( info->tx_holding_count >= info->num_tx_holding_buffers ) { return 0; /* all buffers in use */ } ptx = &info->tx_holding_buffers[info->put_tx_holding_index]; ptx->buffer_size = BufferSize; memcpy( ptx->buffer, Buffer, BufferSize); ++info->tx_holding_count; if ( ++info->put_tx_holding_index >= info->num_tx_holding_buffers) info->put_tx_holding_index=0; return 1; } int mgsl_claim_resources(struct mgsl_struct *info) { if (request_region(info->io_base,info->io_addr_size,"synclink") == NULL) { printk( "%s(%d):I/O address conflict on device %s Addr=%08X\n", __FILE__,__LINE__,info->device_name, info->io_base); return -ENODEV; } info->io_addr_requested = 1; if ( request_irq(info->irq_level,mgsl_interrupt,info->irq_flags, info->device_name, info ) < 0 ) { printk( "%s(%d):Cant request interrupt on device %s IRQ=%d\n", __FILE__,__LINE__,info->device_name, info->irq_level ); goto errout; } info->irq_requested = 1; if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { if (request_mem_region(info->phys_memory_base,0x40000,"synclink") == NULL) { printk( "%s(%d):mem addr conflict device %s Addr=%08X\n", __FILE__,__LINE__,info->device_name, info->phys_memory_base); goto errout; } info->shared_mem_requested = 1; if (request_mem_region(info->phys_lcr_base + info->lcr_offset,128,"synclink") == NULL) { printk( "%s(%d):lcr mem addr conflict device %s Addr=%08X\n", __FILE__,__LINE__,info->device_name, info->phys_lcr_base + info->lcr_offset); goto errout; } info->lcr_mem_requested = 1; info->memory_base = ioremap(info->phys_memory_base,0x40000); if (!info->memory_base) { printk( "%s(%d):Cant map shared memory on device %s MemAddr=%08X\n", __FILE__,__LINE__,info->device_name, info->phys_memory_base ); goto errout; } if ( !mgsl_memory_test(info) ) { printk( "%s(%d):Failed shared memory test %s MemAddr=%08X\n", __FILE__,__LINE__,info->device_name, info->phys_memory_base ); goto errout; } info->lcr_base = ioremap(info->phys_lcr_base,PAGE_SIZE) + info->lcr_offset; if (!info->lcr_base) { printk( "%s(%d):Cant map LCR memory on device %s MemAddr=%08X\n", __FILE__,__LINE__,info->device_name, info->phys_lcr_base ); goto errout; } } else { /* claim DMA channel */ if (request_dma(info->dma_level,info->device_name) < 0){ printk( "%s(%d):Cant request DMA channel on device %s DMA=%d\n", __FILE__,__LINE__,info->device_name, info->dma_level ); mgsl_release_resources( info ); return -ENODEV; } info->dma_requested = 1; /* ISA adapter uses bus master DMA */ set_dma_mode(info->dma_level,DMA_MODE_CASCADE); enable_dma(info->dma_level); } if ( mgsl_allocate_dma_buffers(info) < 0 ) { printk( "%s(%d):Cant allocate DMA buffers on device %s DMA=%d\n", __FILE__,__LINE__,info->device_name, info->dma_level ); goto errout; } return 0; errout: mgsl_release_resources(info); return -ENODEV; } /* end of mgsl_claim_resources() */ void mgsl_release_resources(struct mgsl_struct *info) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_release_resources(%s) entry\n", __FILE__,__LINE__,info->device_name ); if ( info->irq_requested ) { free_irq(info->irq_level, info); info->irq_requested = 0; } if ( info->dma_requested ) { disable_dma(info->dma_level); free_dma(info->dma_level); info->dma_requested = 0; } mgsl_free_dma_buffers(info); mgsl_free_intermediate_rxbuffer_memory(info); mgsl_free_intermediate_txbuffer_memory(info); if ( info->io_addr_requested ) { release_region(info->io_base,info->io_addr_size); info->io_addr_requested = 0; } if ( info->shared_mem_requested ) { release_mem_region(info->phys_memory_base,0x40000); info->shared_mem_requested = 0; } if ( info->lcr_mem_requested ) { release_mem_region(info->phys_lcr_base + info->lcr_offset,128); info->lcr_mem_requested = 0; } if (info->memory_base){ iounmap(info->memory_base); info->memory_base = 0; } if (info->lcr_base){ iounmap(info->lcr_base - info->lcr_offset); info->lcr_base = 0; } if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_release_resources(%s) exit\n", __FILE__,__LINE__,info->device_name ); } /* end of mgsl_release_resources() */ /* mgsl_add_device() * * Add the specified device instance data structure to the * global linked list of devices and increment the device count. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_add_device( struct mgsl_struct *info ) { info->next_device = NULL; info->line = mgsl_device_count; sprintf(info->device_name,"ttySL%d",info->line); if (info->line < MAX_TOTAL_DEVICES) { if (maxframe[info->line]) info->max_frame_size = maxframe[info->line]; info->dosyncppp = dosyncppp[info->line]; if (txdmabufs[info->line]) { info->num_tx_dma_buffers = txdmabufs[info->line]; if (info->num_tx_dma_buffers < 1) info->num_tx_dma_buffers = 1; } if (txholdbufs[info->line]) { info->num_tx_holding_buffers = txholdbufs[info->line]; if (info->num_tx_holding_buffers < 1) info->num_tx_holding_buffers = 1; else if (info->num_tx_holding_buffers > MAX_TX_HOLDING_BUFFERS) info->num_tx_holding_buffers = MAX_TX_HOLDING_BUFFERS; } } mgsl_device_count++; if ( !mgsl_device_list ) mgsl_device_list = info; else { struct mgsl_struct *current_dev = mgsl_device_list; while( current_dev->next_device ) current_dev = current_dev->next_device; current_dev->next_device = info; } if ( info->max_frame_size < 4096 ) info->max_frame_size = 4096; else if ( info->max_frame_size > 65535 ) info->max_frame_size = 65535; if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { printk( "SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n", info->hw_version + 1, info->device_name, info->io_base, info->irq_level, info->phys_memory_base, info->phys_lcr_base, info->max_frame_size ); } else { printk( "SyncLink ISA %s: IO=%04X IRQ=%d DMA=%d MaxFrameSize=%u\n", info->device_name, info->io_base, info->irq_level, info->dma_level, info->max_frame_size ); } #ifdef CONFIG_SYNCLINK_SYNCPPP #ifdef MODULE if (info->dosyncppp) #endif mgsl_sppp_init(info); #endif } /* end of mgsl_add_device() */ /* mgsl_allocate_device() * * Allocate and initialize a device instance structure * * Arguments: none * Return Value: pointer to mgsl_struct if success, otherwise NULL */ struct mgsl_struct* mgsl_allocate_device() { struct mgsl_struct *info; info = (struct mgsl_struct *)kmalloc(sizeof(struct mgsl_struct), GFP_KERNEL); if (!info) { printk("Error can't allocate device instance data\n"); } else { memset(info, 0, sizeof(struct mgsl_struct)); info->magic = MGSL_MAGIC; info->task.sync = 0; info->task.routine = mgsl_bh_handler; info->task.data = info; info->max_frame_size = 4096; info->close_delay = 5*HZ/10; info->closing_wait = 30*HZ; init_waitqueue_head(&info->open_wait); init_waitqueue_head(&info->close_wait); init_waitqueue_head(&info->status_event_wait_q); init_waitqueue_head(&info->event_wait_q); spin_lock_init(&info->irq_spinlock); spin_lock_init(&info->netlock); memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS)); info->idle_mode = HDLC_TXIDLE_FLAGS; info->num_tx_dma_buffers = 1; info->num_tx_holding_buffers = 0; } return info; } /* end of mgsl_allocate_device()*/ /* * perform tty device initialization */ int mgsl_init_tty(void); int mgsl_init_tty() { struct mgsl_struct *info; memset(serial_table,0,sizeof(struct tty_struct*)*MAX_TOTAL_DEVICES); memset(serial_termios,0,sizeof(struct termios*)*MAX_TOTAL_DEVICES); memset(serial_termios_locked,0,sizeof(struct termios*)*MAX_TOTAL_DEVICES); /* Initialize the tty_driver structure */ memset(&serial_driver, 0, sizeof(struct tty_driver)); serial_driver.magic = TTY_DRIVER_MAGIC; serial_driver.driver_name = "synclink"; serial_driver.name = "ttySL"; serial_driver.major = ttymajor; serial_driver.minor_start = 64; serial_driver.num = mgsl_device_count; serial_driver.type = TTY_DRIVER_TYPE_SERIAL; serial_driver.subtype = SERIAL_TYPE_NORMAL; serial_driver.init_termios = tty_std_termios; serial_driver.init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; serial_driver.flags = TTY_DRIVER_REAL_RAW; serial_driver.refcount = &serial_refcount; serial_driver.table = serial_table; serial_driver.termios = serial_termios; serial_driver.termios_locked = serial_termios_locked; serial_driver.open = mgsl_open; serial_driver.close = mgsl_close; serial_driver.write = mgsl_write; serial_driver.put_char = mgsl_put_char; serial_driver.flush_chars = mgsl_flush_chars; serial_driver.write_room = mgsl_write_room; serial_driver.chars_in_buffer = mgsl_chars_in_buffer; serial_driver.flush_buffer = mgsl_flush_buffer; serial_driver.ioctl = mgsl_ioctl; serial_driver.throttle = mgsl_throttle; serial_driver.unthrottle = mgsl_unthrottle; serial_driver.send_xchar = mgsl_send_xchar; serial_driver.break_ctl = mgsl_break; serial_driver.wait_until_sent = mgsl_wait_until_sent; serial_driver.read_proc = mgsl_read_proc; serial_driver.set_termios = mgsl_set_termios; serial_driver.stop = mgsl_stop; serial_driver.start = mgsl_start; serial_driver.hangup = mgsl_hangup; /* * The callout device is just like normal device except for * major number and the subtype code. */ callout_driver = serial_driver; callout_driver.name = "cuaSL"; callout_driver.major = cuamajor; callout_driver.subtype = SERIAL_TYPE_CALLOUT; callout_driver.read_proc = 0; callout_driver.proc_entry = 0; if (tty_register_driver(&serial_driver) < 0) printk("%s(%d):Couldn't register serial driver\n", __FILE__,__LINE__); if (tty_register_driver(&callout_driver) < 0) printk("%s(%d):Couldn't register callout driver\n", __FILE__,__LINE__); printk("%s %s, tty major#%d callout major#%d\n", driver_name, driver_version, serial_driver.major, callout_driver.major); /* Propagate these values to all device instances */ info = mgsl_device_list; while(info){ info->callout_termios = callout_driver.init_termios; info->normal_termios = serial_driver.init_termios; info = info->next_device; } return 0; } /* enumerate user specified ISA adapters */ int mgsl_enum_isa_devices() { struct mgsl_struct *info; int i; /* Check for user specified ISA devices */ for (i=0 ;(i < MAX_ISA_DEVICES) && io[i] && irq[i]; i++){ if ( debug_level >= DEBUG_LEVEL_INFO ) printk("ISA device specified io=%04X,irq=%d,dma=%d\n", io[i], irq[i], dma[i] ); info = mgsl_allocate_device(); if ( !info ) { /* error allocating device instance data */ if ( debug_level >= DEBUG_LEVEL_ERROR ) printk( "can't allocate device instance data.\n"); continue; } /* Copy user configuration info to device instance data */ info->io_base = (unsigned int)io[i]; info->irq_level = (unsigned int)irq[i]; info->irq_level = irq_cannonicalize(info->irq_level); info->dma_level = (unsigned int)dma[i]; info->bus_type = MGSL_BUS_TYPE_ISA; info->io_addr_size = 16; info->irq_flags = 0; mgsl_add_device( info ); } return 0; } /* mgsl_init() * * Driver initialization entry point. * * Arguments: None * Return Value: 0 if success, otherwise error code */ int __init mgsl_init(void) { int rc; EXPORT_NO_SYMBOLS; printk("%s %s\n", driver_name, driver_version); mgsl_enum_isa_devices(); pci_register_driver(&synclink_pci_driver); if ( !mgsl_device_list ) { printk("%s(%d):No SyncLink devices found.\n",__FILE__,__LINE__); return -ENODEV; } if ((rc = mgsl_init_tty())) return rc; return 0; } static int __init synclink_init(void) { /* Uncomment this to kernel debug module. * mgsl_get_text_ptr() leaves the .text address in eax * which can be used with add-symbol-file with gdb. */ if (break_on_load) { mgsl_get_text_ptr(); BREAKPOINT(); } return mgsl_init(); } static void __exit synclink_exit(void) { unsigned long flags; int rc; struct mgsl_struct *info; struct mgsl_struct *tmp; printk("Unloading %s: %s\n", driver_name, driver_version); save_flags(flags); cli(); if ((rc = tty_unregister_driver(&serial_driver))) printk("%s(%d) failed to unregister tty driver err=%d\n", __FILE__,__LINE__,rc); if ((rc = tty_unregister_driver(&callout_driver))) printk("%s(%d) failed to unregister callout driver err=%d\n", __FILE__,__LINE__,rc); restore_flags(flags); info = mgsl_device_list; while(info) { #ifdef CONFIG_SYNCLINK_SYNCPPP if (info->dosyncppp) mgsl_sppp_delete(info); #endif mgsl_release_resources(info); tmp = info; info = info->next_device; kfree(tmp); } if (tmp_buf) { free_page((unsigned long) tmp_buf); tmp_buf = NULL; } pci_unregister_driver(&synclink_pci_driver); } module_init(synclink_init); module_exit(synclink_exit); /* * usc_RTCmd() * * Issue a USC Receive/Transmit command to the * Channel Command/Address Register (CCAR). * * Notes: * * The command is encoded in the most significant 5 bits <15..11> * of the CCAR value. Bits <10..7> of the CCAR must be preserved * and Bits <6..0> must be written as zeros. * * Arguments: * * info pointer to device information structure * Cmd command mask (use symbolic macros) * * Return Value: * * None */ void usc_RTCmd( struct mgsl_struct *info, u16 Cmd ) { /* output command to CCAR in bits <15..11> */ /* preserve bits <10..7>, bits <6..0> must be zero */ outw( Cmd + info->loopback_bits, info->io_base + CCAR ); /* Read to flush write to CCAR */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) inw( info->io_base + CCAR ); } /* end of usc_RTCmd() */ /* * usc_DmaCmd() * * Issue a DMA command to the DMA Command/Address Register (DCAR). * * Arguments: * * info pointer to device information structure * Cmd DMA command mask (usc_DmaCmd_XX Macros) * * Return Value: * * None */ void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd ) { /* write command mask to DCAR */ outw( Cmd + info->mbre_bit, info->io_base ); /* Read to flush write to DCAR */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) inw( info->io_base ); } /* end of usc_DmaCmd() */ /* * usc_OutDmaReg() * * Write a 16-bit value to a USC DMA register * * Arguments: * * info pointer to device info structure * RegAddr register address (number) for write * RegValue 16-bit value to write to register * * Return Value: * * None * */ void usc_OutDmaReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue ) { /* Note: The DCAR is located at the adapter base address */ /* Note: must preserve state of BIT8 in DCAR */ outw( RegAddr + info->mbre_bit, info->io_base ); outw( RegValue, info->io_base ); /* Read to flush write to DCAR */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) inw( info->io_base ); } /* end of usc_OutDmaReg() */ /* * usc_InDmaReg() * * Read a 16-bit value from a DMA register * * Arguments: * * info pointer to device info structure * RegAddr register address (number) to read from * * Return Value: * * The 16-bit value read from register * */ u16 usc_InDmaReg( struct mgsl_struct *info, u16 RegAddr ) { /* Note: The DCAR is located at the adapter base address */ /* Note: must preserve state of BIT8 in DCAR */ outw( RegAddr + info->mbre_bit, info->io_base ); return inw( info->io_base ); } /* end of usc_InDmaReg() */ /* * * usc_OutReg() * * Write a 16-bit value to a USC serial channel register * * Arguments: * * info pointer to device info structure * RegAddr register address (number) to write to * RegValue 16-bit value to write to register * * Return Value: * * None * */ void usc_OutReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue ) { outw( RegAddr + info->loopback_bits, info->io_base + CCAR ); outw( RegValue, info->io_base + CCAR ); /* Read to flush write to CCAR */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) inw( info->io_base + CCAR ); } /* end of usc_OutReg() */ /* * usc_InReg() * * Reads a 16-bit value from a USC serial channel register * * Arguments: * * info pointer to device extension * RegAddr register address (number) to read from * * Return Value: * * 16-bit value read from register */ u16 usc_InReg( struct mgsl_struct *info, u16 RegAddr ) { outw( RegAddr + info->loopback_bits, info->io_base + CCAR ); return inw( info->io_base + CCAR ); } /* end of usc_InReg() */ /* usc_set_sdlc_mode() * * Set up the adapter for SDLC DMA communications. * * Arguments: info pointer to device instance data * Return Value: NONE */ void usc_set_sdlc_mode( struct mgsl_struct *info ) { u16 RegValue; int PreSL1660; /* * determine if the IUSC on the adapter is pre-SL1660. If * not, take advantage of the UnderWait feature of more * modern chips. If an underrun occurs and this bit is set, * the transmitter will idle the programmed idle pattern * until the driver has time to service the underrun. Otherwise, * the dma controller may get the cycles previously requested * and begin transmitting queued tx data. */ usc_OutReg(info,TMCR,0x1f); RegValue=usc_InReg(info,TMDR); if ( RegValue == IUSC_PRE_SL1660 ) PreSL1660 = 1; else PreSL1660 = 0; if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE ) { /* ** Channel Mode Register (CMR) ** ** <15..14> 10 Tx Sub Modes, Send Flag on Underrun ** <13> 0 0 = Transmit Disabled (initially) ** <12> 0 1 = Consecutive Idles share common 0 ** <11..8> 1110 Transmitter Mode = HDLC/SDLC Loop ** <7..4> 0000 Rx Sub Modes, addr/ctrl field handling ** <3..0> 0110 Receiver Mode = HDLC/SDLC ** ** 1000 1110 0000 0110 = 0x8e06 */ RegValue = 0x8e06; /*-------------------------------------------------- * ignore user options for UnderRun Actions and * preambles *--------------------------------------------------*/ } else { /* Channel mode Register (CMR) * * <15..14> 00 Tx Sub modes, Underrun Action * <13> 0 1 = Send Preamble before opening flag * <12> 0 1 = Consecutive Idles share common 0 * <11..8> 0110 Transmitter mode = HDLC/SDLC * <7..4> 0000 Rx Sub modes, addr/ctrl field handling * <3..0> 0110 Receiver mode = HDLC/SDLC * * 0000 0110 0000 0110 = 0x0606 */ if (info->params.mode == MGSL_MODE_RAW) { RegValue = 0x0001; /* Set Receive mode = external sync */ usc_OutReg( info, IOCR, /* Set IOCR DCD is RxSync Detect Input */ (unsigned short)((usc_InReg(info, IOCR) & ~(BIT13|BIT12)) | BIT12)); /* * TxSubMode: * CMR <15> 0 Don't send CRC on Tx Underrun * CMR <14> x undefined * CMR <13> 0 Send preamble before openning sync * CMR <12> 0 Send 8-bit syncs, 1=send Syncs per TxLength * * TxMode: * CMR <11-8) 0100 MonoSync * * 0x00 0100 xxxx xxxx 04xx */ RegValue |= 0x0400; } else { RegValue = 0x0606; if ( info->params.flags & HDLC_FLAG_UNDERRUN_ABORT15 ) RegValue |= BIT14; else if ( info->params.flags & HDLC_FLAG_UNDERRUN_FLAG ) RegValue |= BIT15; else if ( info->params.flags & HDLC_FLAG_UNDERRUN_CRC ) RegValue |= BIT15 + BIT14; } if ( info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE ) RegValue |= BIT13; } if ( info->params.mode == MGSL_MODE_HDLC && (info->params.flags & HDLC_FLAG_SHARE_ZERO) ) RegValue |= BIT12; if ( info->params.addr_filter != 0xff ) { /* set up receive address filtering */ usc_OutReg( info, RSR, info->params.addr_filter ); RegValue |= BIT4; } usc_OutReg( info, CMR, RegValue ); info->cmr_value = RegValue; /* Receiver mode Register (RMR) * * <15..13> 000 encoding * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1) * <10> 1 1 = Set CRC to all 1s (use for SDLC/HDLC) * <9> 0 1 = Include Receive chars in CRC * <8> 1 1 = Use Abort/PE bit as abort indicator * <7..6> 00 Even parity * <5> 0 parity disabled * <4..2> 000 Receive Char Length = 8 bits * <1..0> 00 Disable Receiver * * 0000 0101 0000 0000 = 0x0500 */ RegValue = 0x0500; switch ( info->params.encoding ) { case HDLC_ENCODING_NRZB: RegValue |= BIT13; break; case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break; case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 + BIT13; break; case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break; case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 + BIT13; break; case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14; break; case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14 + BIT13; break; } if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT ) RegValue |= BIT9; else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT ) RegValue |= ( BIT12 | BIT10 | BIT9 ); usc_OutReg( info, RMR, RegValue ); /* Set the Receive count Limit Register (RCLR) to 0xffff. */ /* When an opening flag of an SDLC frame is recognized the */ /* Receive Character count (RCC) is loaded with the value in */ /* RCLR. The RCC is decremented for each received byte. The */ /* value of RCC is stored after the closing flag of the frame */ /* allowing the frame size to be computed. */ usc_OutReg( info, RCLR, RCLRVALUE ); usc_RCmd( info, RCmd_SelectRicrdma_level ); /* Receive Interrupt Control Register (RICR) * * <15..8> ? RxFIFO DMA Request Level * <7> 0 Exited Hunt IA (Interrupt Arm) * <6> 0 Idle Received IA * <5> 0 Break/Abort IA * <4> 0 Rx Bound IA * <3> 1 Queued status reflects oldest 2 bytes in FIFO * <2> 0 Abort/PE IA * <1> 1 Rx Overrun IA * <0> 0 Select TC0 value for readback * * 0000 0000 0000 1000 = 0x000a */ /* Carry over the Exit Hunt and Idle Received bits */ /* in case they have been armed by usc_ArmEvents. */ RegValue = usc_InReg( info, RICR ) & 0xc0; if ( info->bus_type == MGSL_BUS_TYPE_PCI ) usc_OutReg( info, RICR, (u16)(0x030a | RegValue) ); else usc_OutReg( info, RICR, (u16)(0x140a | RegValue) ); /* Unlatch all Rx status bits and clear Rx status IRQ Pending */ usc_UnlatchRxstatusBits( info, RXSTATUS_ALL ); usc_ClearIrqPendingBits( info, RECEIVE_STATUS ); /* Transmit mode Register (TMR) * * <15..13> 000 encoding * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1) * <10> 1 1 = Start CRC as all 1s (use for SDLC/HDLC) * <9> 0 1 = Tx CRC Enabled * <8> 0 1 = Append CRC to end of transmit frame * <7..6> 00 Transmit parity Even * <5> 0 Transmit parity Disabled * <4..2> 000 Tx Char Length = 8 bits * <1..0> 00 Disable Transmitter * * 0000 0100 0000 0000 = 0x0400 */ RegValue = 0x0400; switch ( info->params.encoding ) { case HDLC_ENCODING_NRZB: RegValue |= BIT13; break; case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break; case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 + BIT13; break; case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break; case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 + BIT13; break; case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14; break; case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14 + BIT13; break; } if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT ) RegValue |= BIT9 + BIT8; else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT ) RegValue |= ( BIT12 | BIT10 | BIT9 | BIT8); usc_OutReg( info, TMR, RegValue ); usc_set_txidle( info ); usc_TCmd( info, TCmd_SelectTicrdma_level ); /* Transmit Interrupt Control Register (TICR) * * <15..8> ? Transmit FIFO DMA Level * <7> 0 Present IA (Interrupt Arm) * <6> 0 Idle Sent IA * <5> 1 Abort Sent IA * <4> 1 EOF/EOM Sent IA * <3> 0 CRC Sent IA * <2> 1 1 = Wait for SW Trigger to Start Frame * <1> 1 Tx Underrun IA * <0> 0 TC0 constant on read back * * 0000 0000 0011 0110 = 0x0036 */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) usc_OutReg( info, TICR, 0x0736 ); else usc_OutReg( info, TICR, 0x1436 ); usc_UnlatchTxstatusBits( info, TXSTATUS_ALL ); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS ); /* ** Transmit Command/Status Register (TCSR) ** ** <15..12> 0000 TCmd ** <11> 0/1 UnderWait ** <10..08> 000 TxIdle ** <7> x PreSent ** <6> x IdleSent ** <5> x AbortSent ** <4> x EOF/EOM Sent ** <3> x CRC Sent ** <2> x All Sent ** <1> x TxUnder ** <0> x TxEmpty ** ** 0000 0000 0000 0000 = 0x0000 */ info->tcsr_value = 0; if ( !PreSL1660 ) info->tcsr_value |= TCSR_UNDERWAIT; usc_OutReg( info, TCSR, info->tcsr_value ); /* Clock mode Control Register (CMCR) * * <15..14> 00 counter 1 Source = Disabled * <13..12> 00 counter 0 Source = Disabled * <11..10> 11 BRG1 Input is TxC Pin * <9..8> 11 BRG0 Input is TxC Pin * <7..6> 01 DPLL Input is BRG1 Output * <5..3> XXX TxCLK comes from Port 0 * <2..0> XXX RxCLK comes from Port 1 * * 0000 1111 0111 0111 = 0x0f77 */ RegValue = 0x0f40; if ( info->params.flags & HDLC_FLAG_RXC_DPLL ) RegValue |= 0x0003; /* RxCLK from DPLL */ else if ( info->params.flags & HDLC_FLAG_RXC_BRG ) RegValue |= 0x0004; /* RxCLK from BRG0 */ else if ( info->params.flags & HDLC_FLAG_RXC_TXCPIN) RegValue |= 0x0006; /* RxCLK from TXC Input */ else RegValue |= 0x0007; /* RxCLK from Port1 */ if ( info->params.flags & HDLC_FLAG_TXC_DPLL ) RegValue |= 0x0018; /* TxCLK from DPLL */ else if ( info->params.flags & HDLC_FLAG_TXC_BRG ) RegValue |= 0x0020; /* TxCLK from BRG0 */ else if ( info->params.flags & HDLC_FLAG_TXC_RXCPIN) RegValue |= 0x0038; /* RxCLK from TXC Input */ else RegValue |= 0x0030; /* TxCLK from Port0 */ usc_OutReg( info, CMCR, RegValue ); /* Hardware Configuration Register (HCR) * * <15..14> 00 CTR0 Divisor:00=32,01=16,10=8,11=4 * <13> 0 CTR1DSel:0=CTR0Div determines CTR0Div * <12> 0 CVOK:0=report code violation in biphase * <11..10> 00 DPLL Divisor:00=32,01=16,10=8,11=4 * <9..8> XX DPLL mode:00=disable,01=NRZ,10=Biphase,11=Biphase Level * <7..6> 00 reserved * <5> 0 BRG1 mode:0=continuous,1=single cycle * <4> X BRG1 Enable * <3..2> 00 reserved * <1> 0 BRG0 mode:0=continuous,1=single cycle * <0> 0 BRG0 Enable */ RegValue = 0x0000; if ( info->params.flags & (HDLC_FLAG_RXC_DPLL + HDLC_FLAG_TXC_DPLL) ) { u32 XtalSpeed; u32 DpllDivisor; u16 Tc; /* DPLL is enabled. Use BRG1 to provide continuous reference clock */ /* for DPLL. DPLL mode in HCR is dependent on the encoding used. */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) XtalSpeed = 11059200; else XtalSpeed = 14745600; if ( info->params.flags & HDLC_FLAG_DPLL_DIV16 ) { DpllDivisor = 16; RegValue |= BIT10; } else if ( info->params.flags & HDLC_FLAG_DPLL_DIV8 ) { DpllDivisor = 8; RegValue |= BIT11; } else DpllDivisor = 32; /* Tc = (Xtal/Speed) - 1 */ /* If twice the remainder of (Xtal/Speed) is greater than Speed */ /* then rounding up gives a more precise time constant. Instead */ /* of rounding up and then subtracting 1 we just don't subtract */ /* the one in this case. */ /*-------------------------------------------------- * ejz: for DPLL mode, application should use the * same clock speed as the partner system, even * though clocking is derived from the input RxData. * In case the user uses a 0 for the clock speed, * default to 0xffffffff and don't try to divide by * zero *--------------------------------------------------*/ if ( info->params.clock_speed ) { Tc = (u16)((XtalSpeed/DpllDivisor)/info->params.clock_speed); if ( !((((XtalSpeed/DpllDivisor) % info->params.clock_speed) * 2) / info->params.clock_speed) ) Tc--; } else Tc = -1; /* Write 16-bit Time Constant for BRG1 */ usc_OutReg( info, TC1R, Tc ); RegValue |= BIT4; /* enable BRG1 */ switch ( info->params.encoding ) { case HDLC_ENCODING_NRZ: case HDLC_ENCODING_NRZB: case HDLC_ENCODING_NRZI_MARK: case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT8; break; case HDLC_ENCODING_BIPHASE_MARK: case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT9; break; case HDLC_ENCODING_BIPHASE_LEVEL: case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT9 + BIT8; break; } } usc_OutReg( info, HCR, RegValue ); /* Channel Control/status Register (CCSR) * * <15> X RCC FIFO Overflow status (RO) * <14> X RCC FIFO Not Empty status (RO) * <13> 0 1 = Clear RCC FIFO (WO) * <12> X DPLL Sync (RW) * <11> X DPLL 2 Missed Clocks status (RO) * <10> X DPLL 1 Missed Clock status (RO) * <9..8> 00 DPLL Resync on rising and falling edges (RW) * <7> X SDLC Loop On status (RO) * <6> X SDLC Loop Send status (RO) * <5> 1 Bypass counters for TxClk and RxClk (RW) * <4..2> 000 Last Char of SDLC frame has 8 bits (RW) * <1..0> 00 reserved * * 0000 0000 0010 0000 = 0x0020 */ usc_OutReg( info, CCSR, 0x1020 ); if ( info->params.flags & HDLC_FLAG_AUTO_CTS ) { usc_OutReg( info, SICR, (u16)(usc_InReg(info,SICR) | SICR_CTS_INACTIVE) ); } /* enable Master Interrupt Enable bit (MIE) */ usc_EnableMasterIrqBit( info ); usc_ClearIrqPendingBits( info, RECEIVE_STATUS + RECEIVE_DATA + TRANSMIT_STATUS + TRANSMIT_DATA + MISC); /* arm RCC underflow interrupt */ usc_OutReg(info, SICR, (u16)(usc_InReg(info,SICR) | BIT3)); usc_EnableInterrupts(info, MISC); info->mbre_bit = 0; outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */ usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */ info->mbre_bit = BIT8; outw( BIT8, info->io_base ); /* set Master Bus Enable (DCAR) */ if (info->bus_type == MGSL_BUS_TYPE_ISA) { /* Enable DMAEN (Port 7, Bit 14) */ /* This connects the DMA request signal to the ISA bus */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) & ~BIT14)); } /* DMA Control Register (DCR) * * <15..14> 10 Priority mode = Alternating Tx/Rx * 01 Rx has priority * 00 Tx has priority * * <13> 1 Enable Priority Preempt per DCR<15..14> * (WARNING DCR<11..10> must be 00 when this is 1) * 0 Choose activate channel per DCR<11..10> * * <12> 0 Little Endian for Array/List * <11..10> 00 Both Channels can use each bus grant * <9..6> 0000 reserved * <5> 0 7 CLK - Minimum Bus Re-request Interval * <4> 0 1 = drive D/C and S/D pins * <3> 1 1 = Add one wait state to all DMA cycles. * <2> 0 1 = Strobe /UAS on every transfer. * <1..0> 11 Addr incrementing only affects LS24 bits * * 0110 0000 0000 1011 = 0x600b */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { /* PCI adapter does not need DMA wait state */ usc_OutDmaReg( info, DCR, 0xa00b ); } else usc_OutDmaReg( info, DCR, 0x800b ); /* Receive DMA mode Register (RDMR) * * <15..14> 11 DMA mode = Linked List Buffer mode * <13> 1 RSBinA/L = store Rx status Block in Arrary/List entry * <12> 1 Clear count of List Entry after fetching * <11..10> 00 Address mode = Increment * <9> 1 Terminate Buffer on RxBound * <8> 0 Bus Width = 16bits * <7..0> ? status Bits (write as 0s) * * 1111 0010 0000 0000 = 0xf200 */ usc_OutDmaReg( info, RDMR, 0xf200 ); /* Transmit DMA mode Register (TDMR) * * <15..14> 11 DMA mode = Linked List Buffer mode * <13> 1 TCBinA/L = fetch Tx Control Block from List entry * <12> 1 Clear count of List Entry after fetching * <11..10> 00 Address mode = Increment * <9> 1 Terminate Buffer on end of frame * <8> 0 Bus Width = 16bits * <7..0> ? status Bits (Read Only so write as 0) * * 1111 0010 0000 0000 = 0xf200 */ usc_OutDmaReg( info, TDMR, 0xf200 ); /* DMA Interrupt Control Register (DICR) * * <15> 1 DMA Interrupt Enable * <14> 0 1 = Disable IEO from USC * <13> 0 1 = Don't provide vector during IntAck * <12> 1 1 = Include status in Vector * <10..2> 0 reserved, Must be 0s * <1> 0 1 = Rx DMA Interrupt Enabled * <0> 0 1 = Tx DMA Interrupt Enabled * * 1001 0000 0000 0000 = 0x9000 */ usc_OutDmaReg( info, DICR, 0x9000 ); usc_InDmaReg( info, RDMR ); /* clear pending receive DMA IRQ bits */ usc_InDmaReg( info, TDMR ); /* clear pending transmit DMA IRQ bits */ usc_OutDmaReg( info, CDIR, 0x0303 ); /* clear IUS and Pending for Tx and Rx */ /* Channel Control Register (CCR) * * <15..14> 10 Use 32-bit Tx Control Blocks (TCBs) * <13> 0 Trigger Tx on SW Command Disabled * <12> 0 Flag Preamble Disabled * <11..10> 00 Preamble Length * <9..8> 00 Preamble Pattern * <7..6> 10 Use 32-bit Rx status Blocks (RSBs) * <5> 0 Trigger Rx on SW Command Disabled * <4..0> 0 reserved * * 1000 0000 1000 0000 = 0x8080 */ RegValue = 0x8080; switch ( info->params.preamble_length ) { case HDLC_PREAMBLE_LENGTH_16BITS: RegValue |= BIT10; break; case HDLC_PREAMBLE_LENGTH_32BITS: RegValue |= BIT11; break; case HDLC_PREAMBLE_LENGTH_64BITS: RegValue |= BIT11 + BIT10; break; } switch ( info->params.preamble ) { case HDLC_PREAMBLE_PATTERN_FLAGS: RegValue |= BIT8 + BIT12; break; case HDLC_PREAMBLE_PATTERN_ONES: RegValue |= BIT8; break; case HDLC_PREAMBLE_PATTERN_10: RegValue |= BIT9; break; case HDLC_PREAMBLE_PATTERN_01: RegValue |= BIT9 + BIT8; break; } usc_OutReg( info, CCR, RegValue ); /* * Burst/Dwell Control Register * * <15..8> 0x20 Maximum number of transfers per bus grant * <7..0> 0x00 Maximum number of clock cycles per bus grant */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { /* don't limit bus occupancy on PCI adapter */ usc_OutDmaReg( info, BDCR, 0x0000 ); } else usc_OutDmaReg( info, BDCR, 0x2000 ); usc_stop_transmitter(info); usc_stop_receiver(info); } /* end of usc_set_sdlc_mode() */ /* usc_enable_loopback() * * Set the 16C32 for internal loopback mode. * The TxCLK and RxCLK signals are generated from the BRG0 and * the TxD is looped back to the RxD internally. * * Arguments: info pointer to device instance data * enable 1 = enable loopback, 0 = disable * Return Value: None */ void usc_enable_loopback(struct mgsl_struct *info, int enable) { if (enable) { /* blank external TXD output */ usc_OutReg(info,IOCR,usc_InReg(info,IOCR) | (BIT7+BIT6)); /* Clock mode Control Register (CMCR) * * <15..14> 00 counter 1 Disabled * <13..12> 00 counter 0 Disabled * <11..10> 11 BRG1 Input is TxC Pin * <9..8> 11 BRG0 Input is TxC Pin * <7..6> 01 DPLL Input is BRG1 Output * <5..3> 100 TxCLK comes from BRG0 * <2..0> 100 RxCLK comes from BRG0 * * 0000 1111 0110 0100 = 0x0f64 */ usc_OutReg( info, CMCR, 0x0f64 ); /* Write 16-bit Time Constant for BRG0 */ /* use clock speed if available, otherwise use 8 for diagnostics */ if (info->params.clock_speed) { if (info->bus_type == MGSL_BUS_TYPE_PCI) usc_OutReg(info, TC0R, (u16)((11059200/info->params.clock_speed)-1)); else usc_OutReg(info, TC0R, (u16)((14745600/info->params.clock_speed)-1)); } else usc_OutReg(info, TC0R, (u16)8); /* Hardware Configuration Register (HCR) Clear Bit 1, BRG0 mode = Continuous Set Bit 0 to enable BRG0. */ usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) ); /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */ usc_OutReg(info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004)); /* set Internal Data loopback mode */ info->loopback_bits = 0x300; outw( 0x0300, info->io_base + CCAR ); } else { /* enable external TXD output */ usc_OutReg(info,IOCR,usc_InReg(info,IOCR) & ~(BIT7+BIT6)); /* clear Internal Data loopback mode */ info->loopback_bits = 0; outw( 0,info->io_base + CCAR ); } } /* end of usc_enable_loopback() */ /* usc_enable_aux_clock() * * Enabled the AUX clock output at the specified frequency. * * Arguments: * * info pointer to device extension * data_rate data rate of clock in bits per second * A data rate of 0 disables the AUX clock. * * Return Value: None */ void usc_enable_aux_clock( struct mgsl_struct *info, u32 data_rate ) { u32 XtalSpeed; u16 Tc; if ( data_rate ) { if ( info->bus_type == MGSL_BUS_TYPE_PCI ) XtalSpeed = 11059200; else XtalSpeed = 14745600; /* Tc = (Xtal/Speed) - 1 */ /* If twice the remainder of (Xtal/Speed) is greater than Speed */ /* then rounding up gives a more precise time constant. Instead */ /* of rounding up and then subtracting 1 we just don't subtract */ /* the one in this case. */ Tc = (u16)(XtalSpeed/data_rate); if ( !(((XtalSpeed % data_rate) * 2) / data_rate) ) Tc--; /* Write 16-bit Time Constant for BRG0 */ usc_OutReg( info, TC0R, Tc ); /* * Hardware Configuration Register (HCR) * Clear Bit 1, BRG0 mode = Continuous * Set Bit 0 to enable BRG0. */ usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) ); /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */ usc_OutReg( info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) ); } else { /* data rate == 0 so turn off BRG0 */ usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) ); } } /* end of usc_enable_aux_clock() */ /* * * usc_process_rxoverrun_sync() * * This function processes a receive overrun by resetting the * receive DMA buffers and issuing a Purge Rx FIFO command * to allow the receiver to continue receiving. * * Arguments: * * info pointer to device extension * * Return Value: None */ void usc_process_rxoverrun_sync( struct mgsl_struct *info ) { int start_index; int end_index; int frame_start_index; int start_of_frame_found = FALSE; int end_of_frame_found = FALSE; int reprogram_dma = FALSE; DMABUFFERENTRY *buffer_list = info->rx_buffer_list; u32 phys_addr; usc_DmaCmd( info, DmaCmd_PauseRxChannel ); usc_RCmd( info, RCmd_EnterHuntmode ); usc_RTCmd( info, RTCmd_PurgeRxFifo ); /* CurrentRxBuffer points to the 1st buffer of the next */ /* possibly available receive frame. */ frame_start_index = start_index = end_index = info->current_rx_buffer; /* Search for an unfinished string of buffers. This means */ /* that a receive frame started (at least one buffer with */ /* count set to zero) but there is no terminiting buffer */ /* (status set to non-zero). */ while( !buffer_list[end_index].count ) { /* Count field has been reset to zero by 16C32. */ /* This buffer is currently in use. */ if ( !start_of_frame_found ) { start_of_frame_found = TRUE; frame_start_index = end_index; end_of_frame_found = FALSE; } if ( buffer_list[end_index].status ) { /* Status field has been set by 16C32. */ /* This is the last buffer of a received frame. */ /* We want to leave the buffers for this frame intact. */ /* Move on to next possible frame. */ start_of_frame_found = FALSE; end_of_frame_found = TRUE; } /* advance to next buffer entry in linked list */ end_index++; if ( end_index == info->rx_buffer_count ) end_index = 0; if ( start_index == end_index ) { /* The entire list has been searched with all Counts == 0 and */ /* all Status == 0. The receive buffers are */ /* completely screwed, reset all receive buffers! */ mgsl_reset_rx_dma_buffers( info ); frame_start_index = 0; start_of_frame_found = FALSE; reprogram_dma = TRUE; break; } } if ( start_of_frame_found && !end_of_frame_found ) { /* There is an unfinished string of receive DMA buffers */ /* as a result of the receiver overrun. */ /* Reset the buffers for the unfinished frame */ /* and reprogram the receive DMA controller to start */ /* at the 1st buffer of unfinished frame. */ start_index = frame_start_index; do { *((unsigned long *)&(info->rx_buffer_list[start_index++].count)) = DMABUFFERSIZE; /* Adjust index for wrap around. */ if ( start_index == info->rx_buffer_count ) start_index = 0; } while( start_index != end_index ); reprogram_dma = TRUE; } if ( reprogram_dma ) { usc_UnlatchRxstatusBits(info,RXSTATUS_ALL); usc_ClearIrqPendingBits(info, RECEIVE_DATA|RECEIVE_STATUS); usc_UnlatchRxstatusBits(info, RECEIVE_DATA|RECEIVE_STATUS); usc_EnableReceiver(info,DISABLE_UNCONDITIONAL); /* This empties the receive FIFO and loads the RCC with RCLR */ usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) ); /* program 16C32 with physical address of 1st DMA buffer entry */ phys_addr = info->rx_buffer_list[frame_start_index].phys_entry; usc_OutDmaReg( info, NRARL, (u16)phys_addr ); usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) ); usc_UnlatchRxstatusBits( info, RXSTATUS_ALL ); usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS ); usc_EnableInterrupts( info, RECEIVE_STATUS ); /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */ /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */ usc_OutDmaReg( info, RDIAR, BIT3 + BIT2 ); usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) ); usc_DmaCmd( info, DmaCmd_InitRxChannel ); if ( info->params.flags & HDLC_FLAG_AUTO_DCD ) usc_EnableReceiver(info,ENABLE_AUTO_DCD); else usc_EnableReceiver(info,ENABLE_UNCONDITIONAL); } else { /* This empties the receive FIFO and loads the RCC with RCLR */ usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) ); usc_RTCmd( info, RTCmd_PurgeRxFifo ); } } /* end of usc_process_rxoverrun_sync() */ /* usc_stop_receiver() * * Disable USC receiver * * Arguments: info pointer to device instance data * Return Value: None */ void usc_stop_receiver( struct mgsl_struct *info ) { if (debug_level >= DEBUG_LEVEL_ISR) printk("%s(%d):usc_stop_receiver(%s)\n", __FILE__,__LINE__, info->device_name ); /* Disable receive DMA channel. */ /* This also disables receive DMA channel interrupts */ usc_DmaCmd( info, DmaCmd_ResetRxChannel ); usc_UnlatchRxstatusBits( info, RXSTATUS_ALL ); usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS ); usc_DisableInterrupts( info, RECEIVE_DATA + RECEIVE_STATUS ); usc_EnableReceiver(info,DISABLE_UNCONDITIONAL); /* This empties the receive FIFO and loads the RCC with RCLR */ usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) ); usc_RTCmd( info, RTCmd_PurgeRxFifo ); info->rx_enabled = 0; info->rx_overflow = 0; info->rx_rcc_underrun = 0; } /* end of stop_receiver() */ /* usc_start_receiver() * * Enable the USC receiver * * Arguments: info pointer to device instance data * Return Value: None */ void usc_start_receiver( struct mgsl_struct *info ) { u32 phys_addr; if (debug_level >= DEBUG_LEVEL_ISR) printk("%s(%d):usc_start_receiver(%s)\n", __FILE__,__LINE__, info->device_name ); mgsl_reset_rx_dma_buffers( info ); usc_stop_receiver( info ); usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) ); usc_RTCmd( info, RTCmd_PurgeRxFifo ); if ( info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW ) { /* DMA mode Transfers */ /* Program the DMA controller. */ /* Enable the DMA controller end of buffer interrupt. */ /* program 16C32 with physical address of 1st DMA buffer entry */ phys_addr = info->rx_buffer_list[0].phys_entry; usc_OutDmaReg( info, NRARL, (u16)phys_addr ); usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) ); usc_UnlatchRxstatusBits( info, RXSTATUS_ALL ); usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS ); usc_EnableInterrupts( info, RECEIVE_STATUS ); /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */ /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */ usc_OutDmaReg( info, RDIAR, BIT3 + BIT2 ); usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) ); usc_DmaCmd( info, DmaCmd_InitRxChannel ); if ( info->params.flags & HDLC_FLAG_AUTO_DCD ) usc_EnableReceiver(info,ENABLE_AUTO_DCD); else usc_EnableReceiver(info,ENABLE_UNCONDITIONAL); } else { usc_UnlatchRxstatusBits(info, RXSTATUS_ALL); usc_ClearIrqPendingBits(info, RECEIVE_DATA + RECEIVE_STATUS); usc_EnableInterrupts(info, RECEIVE_DATA); usc_RTCmd( info, RTCmd_PurgeRxFifo ); usc_RCmd( info, RCmd_EnterHuntmode ); usc_EnableReceiver(info,ENABLE_UNCONDITIONAL); } usc_OutReg( info, CCSR, 0x1020 ); info->rx_enabled = 1; } /* end of usc_start_receiver() */ /* usc_start_transmitter() * * Enable the USC transmitter and send a transmit frame if * one is loaded in the DMA buffers. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_start_transmitter( struct mgsl_struct *info ) { u32 phys_addr; unsigned int FrameSize; if (debug_level >= DEBUG_LEVEL_ISR) printk("%s(%d):usc_start_transmitter(%s)\n", __FILE__,__LINE__, info->device_name ); if ( info->xmit_cnt ) { /* If auto RTS enabled and RTS is inactive, then assert */ /* RTS and set a flag indicating that the driver should */ /* negate RTS when the transmission completes. */ info->drop_rts_on_tx_done = 0; if ( info->params.flags & HDLC_FLAG_AUTO_RTS ) { usc_get_serial_signals( info ); if ( !(info->serial_signals & SerialSignal_RTS) ) { info->serial_signals |= SerialSignal_RTS; usc_set_serial_signals( info ); info->drop_rts_on_tx_done = 1; } } if ( info->params.mode == MGSL_MODE_ASYNC ) { if ( !info->tx_active ) { usc_UnlatchTxstatusBits(info, TXSTATUS_ALL); usc_ClearIrqPendingBits(info, TRANSMIT_STATUS + TRANSMIT_DATA); usc_EnableInterrupts(info, TRANSMIT_DATA); usc_load_txfifo(info); } } else { /* Disable transmit DMA controller while programming. */ usc_DmaCmd( info, DmaCmd_ResetTxChannel ); /* Transmit DMA buffer is loaded, so program USC */ /* to send the frame contained in the buffers. */ FrameSize = info->tx_buffer_list[info->start_tx_dma_buffer].rcc; /* if operating in Raw sync mode, reset the rcc component * of the tx dma buffer entry, otherwise, the serial controller * will send a closing sync char after this count. */ if ( info->params.mode == MGSL_MODE_RAW ) info->tx_buffer_list[info->start_tx_dma_buffer].rcc = 0; /* Program the Transmit Character Length Register (TCLR) */ /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */ usc_OutReg( info, TCLR, (u16)FrameSize ); usc_RTCmd( info, RTCmd_PurgeTxFifo ); /* Program the address of the 1st DMA Buffer Entry in linked list */ phys_addr = info->tx_buffer_list[info->start_tx_dma_buffer].phys_entry; usc_OutDmaReg( info, NTARL, (u16)phys_addr ); usc_OutDmaReg( info, NTARU, (u16)(phys_addr >> 16) ); usc_UnlatchTxstatusBits( info, TXSTATUS_ALL ); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS ); usc_EnableInterrupts( info, TRANSMIT_STATUS ); if ( info->params.mode == MGSL_MODE_RAW && info->num_tx_dma_buffers > 1 ) { /* When running external sync mode, attempt to 'stream' transmit */ /* by filling tx dma buffers as they become available. To do this */ /* we need to enable Tx DMA EOB Status interrupts : */ /* */ /* 1. Arm End of Buffer (EOB) Transmit DMA Interrupt (BIT2 of TDIAR) */ /* 2. Enable Transmit DMA Interrupts (BIT0 of DICR) */ usc_OutDmaReg( info, TDIAR, BIT2|BIT3 ); usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT0) ); } /* Initialize Transmit DMA Channel */ usc_DmaCmd( info, DmaCmd_InitTxChannel ); usc_TCmd( info, TCmd_SendFrame ); info->tx_timer.expires = jiffies + jiffies_from_ms(5000); add_timer(&info->tx_timer); } info->tx_active = 1; } if ( !info->tx_enabled ) { info->tx_enabled = 1; if ( info->params.flags & HDLC_FLAG_AUTO_CTS ) usc_EnableTransmitter(info,ENABLE_AUTO_CTS); else usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL); } } /* end of usc_start_transmitter() */ /* usc_stop_transmitter() * * Stops the transmitter and DMA * * Arguments: info pointer to device isntance data * Return Value: None */ void usc_stop_transmitter( struct mgsl_struct *info ) { if (debug_level >= DEBUG_LEVEL_ISR) printk("%s(%d):usc_stop_transmitter(%s)\n", __FILE__,__LINE__, info->device_name ); del_timer(&info->tx_timer); usc_UnlatchTxstatusBits( info, TXSTATUS_ALL ); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA ); usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA ); usc_EnableTransmitter(info,DISABLE_UNCONDITIONAL); usc_DmaCmd( info, DmaCmd_ResetTxChannel ); usc_RTCmd( info, RTCmd_PurgeTxFifo ); info->tx_enabled = 0; info->tx_active = 0; } /* end of usc_stop_transmitter() */ /* usc_load_txfifo() * * Fill the transmit FIFO until the FIFO is full or * there is no more data to load. * * Arguments: info pointer to device extension (instance data) * Return Value: None */ void usc_load_txfifo( struct mgsl_struct *info ) { int Fifocount; u8 TwoBytes[2]; if ( !info->xmit_cnt && !info->x_char ) return; /* Select transmit FIFO status readback in TICR */ usc_TCmd( info, TCmd_SelectTicrTxFifostatus ); /* load the Transmit FIFO until FIFOs full or all data sent */ while( (Fifocount = usc_InReg(info, TICR) >> 8) && info->xmit_cnt ) { /* there is more space in the transmit FIFO and */ /* there is more data in transmit buffer */ if ( (info->xmit_cnt > 1) && (Fifocount > 1) && !info->x_char ) { /* write a 16-bit word from transmit buffer to 16C32 */ TwoBytes[0] = info->xmit_buf[info->xmit_tail++]; info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); TwoBytes[1] = info->xmit_buf[info->xmit_tail++]; info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); outw( *((u16 *)TwoBytes), info->io_base + DATAREG); info->xmit_cnt -= 2; info->icount.tx += 2; } else { /* only 1 byte left to transmit or 1 FIFO slot left */ outw( (inw( info->io_base + CCAR) & 0x0780) | (TDR+LSBONLY), info->io_base + CCAR ); if (info->x_char) { /* transmit pending high priority char */ outw( info->x_char,info->io_base + CCAR ); info->x_char = 0; } else { outw( info->xmit_buf[info->xmit_tail++],info->io_base + CCAR ); info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1); info->xmit_cnt--; } info->icount.tx++; } } } /* end of usc_load_txfifo() */ /* usc_reset() * * Reset the adapter to a known state and prepare it for further use. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_reset( struct mgsl_struct *info ) { if ( info->bus_type == MGSL_BUS_TYPE_PCI ) { int i; u32 readval; /* Set BIT30 of Misc Control Register */ /* (Local Control Register 0x50) to force reset of USC. */ volatile u32 *MiscCtrl = (u32 *)(info->lcr_base + 0x50); u32 *LCR0BRDR = (u32 *)(info->lcr_base + 0x28); info->misc_ctrl_value |= BIT30; *MiscCtrl = info->misc_ctrl_value; /* * Force at least 170ns delay before clearing * reset bit. Each read from LCR takes at least * 30ns so 10 times for 300ns to be safe. */ for(i=0;i<10;i++) readval = *MiscCtrl; info->misc_ctrl_value &= ~BIT30; *MiscCtrl = info->misc_ctrl_value; *LCR0BRDR = BUS_DESCRIPTOR( 1, // Write Strobe Hold (0-3) 2, // Write Strobe Delay (0-3) 2, // Read Strobe Delay (0-3) 0, // NWDD (Write data-data) (0-3) 4, // NWAD (Write Addr-data) (0-31) 0, // NXDA (Read/Write Data-Addr) (0-3) 0, // NRDD (Read Data-Data) (0-3) 5 // NRAD (Read Addr-Data) (0-31) ); } else { /* do HW reset */ outb( 0,info->io_base + 8 ); } info->mbre_bit = 0; info->loopback_bits = 0; info->usc_idle_mode = 0; /* * Program the Bus Configuration Register (BCR) * * <15> 0 Don't use seperate address * <14..6> 0 reserved * <5..4> 00 IAckmode = Default, don't care * <3> 1 Bus Request Totem Pole output * <2> 1 Use 16 Bit data bus * <1> 0 IRQ Totem Pole output * <0> 0 Don't Shift Right Addr * * 0000 0000 0000 1100 = 0x000c * * By writing to io_base + SDPIN the Wait/Ack pin is * programmed to work as a Wait pin. */ outw( 0x000c,info->io_base + SDPIN ); outw( 0,info->io_base ); outw( 0,info->io_base + CCAR ); /* select little endian byte ordering */ usc_RTCmd( info, RTCmd_SelectLittleEndian ); /* Port Control Register (PCR) * * <15..14> 11 Port 7 is Output (~DMAEN, Bit 14 : 0 = Enabled) * <13..12> 11 Port 6 is Output (~INTEN, Bit 12 : 0 = Enabled) * <11..10> 00 Port 5 is Input (No Connect, Don't Care) * <9..8> 00 Port 4 is Input (No Connect, Don't Care) * <7..6> 11 Port 3 is Output (~RTS, Bit 6 : 0 = Enabled ) * <5..4> 11 Port 2 is Output (~DTR, Bit 4 : 0 = Enabled ) * <3..2> 01 Port 1 is Input (Dedicated RxC) * <1..0> 01 Port 0 is Input (Dedicated TxC) * * 1111 0000 1111 0101 = 0xf0f5 */ usc_OutReg( info, PCR, 0xf0f5 ); /* * Input/Output Control Register * * <15..14> 00 CTS is active low input * <13..12> 00 DCD is active low input * <11..10> 00 TxREQ pin is input (DSR) * <9..8> 00 RxREQ pin is input (RI) * <7..6> 00 TxD is output (Transmit Data) * <5..3> 000 TxC Pin in Input (14.7456MHz Clock) * <2..0> 100 RxC is Output (drive with BRG0) * * 0000 0000 0000 0100 = 0x0004 */ usc_OutReg( info, IOCR, 0x0004 ); } /* end of usc_reset() */ /* usc_set_async_mode() * * Program adapter for asynchronous communications. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_set_async_mode( struct mgsl_struct *info ) { u16 RegValue; /* disable interrupts while programming USC */ usc_DisableMasterIrqBit( info ); outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */ usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */ usc_loopback_frame( info ); /* Channel mode Register (CMR) * * <15..14> 00 Tx Sub modes, 00 = 1 Stop Bit * <13..12> 00 00 = 16X Clock * <11..8> 0000 Transmitter mode = Asynchronous * <7..6> 00 reserved? * <5..4> 00 Rx Sub modes, 00 = 16X Clock * <3..0> 0000 Receiver mode = Asynchronous * * 0000 0000 0000 0000 = 0x0 */ RegValue = 0; if ( info->params.stop_bits != 1 ) RegValue |= BIT14; usc_OutReg( info, CMR, RegValue ); /* Receiver mode Register (RMR) * * <15..13> 000 encoding = None * <12..08> 00000 reserved (Sync Only) * <7..6> 00 Even parity * <5> 0 parity disabled * <4..2> 000 Receive Char Length = 8 bits * <1..0> 00 Disable Receiver * * 0000 0000 0000 0000 = 0x0 */ RegValue = 0; if ( info->params.data_bits != 8 ) RegValue |= BIT4+BIT3+BIT2; if ( info->params.parity != ASYNC_PARITY_NONE ) { RegValue |= BIT5; if ( info->params.parity != ASYNC_PARITY_ODD ) RegValue |= BIT6; } usc_OutReg( info, RMR, RegValue ); /* Set IRQ trigger level */ usc_RCmd( info, RCmd_SelectRicrIntLevel ); /* Receive Interrupt Control Register (RICR) * * <15..8> ? RxFIFO IRQ Request Level * * Note: For async mode the receive FIFO level must be set * to 0 to aviod the situation where the FIFO contains fewer bytes * than the trigger level and no more data is expected. * * <7> 0 Exited Hunt IA (Interrupt Arm) * <6> 0 Idle Received IA * <5> 0 Break/Abort IA * <4> 0 Rx Bound IA * <3> 0 Queued status reflects oldest byte in FIFO * <2> 0 Abort/PE IA * <1> 0 Rx Overrun IA * <0> 0 Select TC0 value for readback * * 0000 0000 0100 0000 = 0x0000 + (FIFOLEVEL in MSB) */ usc_OutReg( info, RICR, 0x0000 ); usc_UnlatchRxstatusBits( info, RXSTATUS_ALL ); usc_ClearIrqPendingBits( info, RECEIVE_STATUS ); /* Transmit mode Register (TMR) * * <15..13> 000 encoding = None * <12..08> 00000 reserved (Sync Only) * <7..6> 00 Transmit parity Even * <5> 0 Transmit parity Disabled * <4..2> 000 Tx Char Length = 8 bits * <1..0> 00 Disable Transmitter * * 0000 0000 0000 0000 = 0x0 */ RegValue = 0; if ( info->params.data_bits != 8 ) RegValue |= BIT4+BIT3+BIT2; if ( info->params.parity != ASYNC_PARITY_NONE ) { RegValue |= BIT5; if ( info->params.parity != ASYNC_PARITY_ODD ) RegValue |= BIT6; } usc_OutReg( info, TMR, RegValue ); usc_set_txidle( info ); /* Set IRQ trigger level */ usc_TCmd( info, TCmd_SelectTicrIntLevel ); /* Transmit Interrupt Control Register (TICR) * * <15..8> ? Transmit FIFO IRQ Level * <7> 0 Present IA (Interrupt Arm) * <6> 1 Idle Sent IA * <5> 0 Abort Sent IA * <4> 0 EOF/EOM Sent IA * <3> 0 CRC Sent IA * <2> 0 1 = Wait for SW Trigger to Start Frame * <1> 0 Tx Underrun IA * <0> 0 TC0 constant on read back * * 0000 0000 0100 0000 = 0x0040 */ usc_OutReg( info, TICR, 0x1f40 ); usc_UnlatchTxstatusBits( info, TXSTATUS_ALL ); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS ); usc_enable_async_clock( info, info->params.data_rate ); /* Channel Control/status Register (CCSR) * * <15> X RCC FIFO Overflow status (RO) * <14> X RCC FIFO Not Empty status (RO) * <13> 0 1 = Clear RCC FIFO (WO) * <12> X DPLL in Sync status (RO) * <11> X DPLL 2 Missed Clocks status (RO) * <10> X DPLL 1 Missed Clock status (RO) * <9..8> 00 DPLL Resync on rising and falling edges (RW) * <7> X SDLC Loop On status (RO) * <6> X SDLC Loop Send status (RO) * <5> 1 Bypass counters for TxClk and RxClk (RW) * <4..2> 000 Last Char of SDLC frame has 8 bits (RW) * <1..0> 00 reserved * * 0000 0000 0010 0000 = 0x0020 */ usc_OutReg( info, CCSR, 0x0020 ); usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA + RECEIVE_DATA + RECEIVE_STATUS ); usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA + RECEIVE_DATA + RECEIVE_STATUS ); usc_EnableMasterIrqBit( info ); if (info->bus_type == MGSL_BUS_TYPE_ISA) { /* Enable INTEN (Port 6, Bit12) */ /* This connects the IRQ request signal to the ISA bus */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12)); } } /* end of usc_set_async_mode() */ /* usc_loopback_frame() * * Loop back a small (2 byte) dummy SDLC frame. * Interrupts and DMA are NOT used. The purpose of this is to * clear any 'stale' status info left over from running in async mode. * * The 16C32 shows the strange behaviour of marking the 1st * received SDLC frame with a CRC error even when there is no * CRC error. To get around this a small dummy from of 2 bytes * is looped back when switching from async to sync mode. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_loopback_frame( struct mgsl_struct *info ) { int i; unsigned long oldmode = info->params.mode; info->params.mode = MGSL_MODE_HDLC; usc_DisableMasterIrqBit( info ); usc_set_sdlc_mode( info ); usc_enable_loopback( info, 1 ); /* Write 16-bit Time Constant for BRG0 */ usc_OutReg( info, TC0R, 0 ); /* Channel Control Register (CCR) * * <15..14> 00 Don't use 32-bit Tx Control Blocks (TCBs) * <13> 0 Trigger Tx on SW Command Disabled * <12> 0 Flag Preamble Disabled * <11..10> 00 Preamble Length = 8-Bits * <9..8> 01 Preamble Pattern = flags * <7..6> 10 Don't use 32-bit Rx status Blocks (RSBs) * <5> 0 Trigger Rx on SW Command Disabled * <4..0> 0 reserved * * 0000 0001 0000 0000 = 0x0100 */ usc_OutReg( info, CCR, 0x0100 ); /* SETUP RECEIVER */ usc_RTCmd( info, RTCmd_PurgeRxFifo ); usc_EnableReceiver(info,ENABLE_UNCONDITIONAL); /* SETUP TRANSMITTER */ /* Program the Transmit Character Length Register (TCLR) */ /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */ usc_OutReg( info, TCLR, 2 ); usc_RTCmd( info, RTCmd_PurgeTxFifo ); /* unlatch Tx status bits, and start transmit channel. */ usc_UnlatchTxstatusBits(info,TXSTATUS_ALL); outw(0,info->io_base + DATAREG); /* ENABLE TRANSMITTER */ usc_TCmd( info, TCmd_SendFrame ); usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL); /* WAIT FOR RECEIVE COMPLETE */ for (i=0 ; i<1000 ; i++) if (usc_InReg( info, RCSR ) & (BIT8 + BIT4 + BIT3 + BIT1)) break; /* clear Internal Data loopback mode */ usc_enable_loopback(info, 0); usc_EnableMasterIrqBit(info); info->params.mode = oldmode; } /* end of usc_loopback_frame() */ /* usc_set_sync_mode() Programs the USC for SDLC communications. * * Arguments: info pointer to adapter info structure * Return Value: None */ void usc_set_sync_mode( struct mgsl_struct *info ) { usc_loopback_frame( info ); usc_set_sdlc_mode( info ); if (info->bus_type == MGSL_BUS_TYPE_ISA) { /* Enable INTEN (Port 6, Bit12) */ /* This connects the IRQ request signal to the ISA bus */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12)); } usc_enable_aux_clock(info, info->params.clock_speed); if (info->params.loopback) usc_enable_loopback(info,1); } /* end of mgsl_set_sync_mode() */ /* usc_set_txidle() Set the HDLC idle mode for the transmitter. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_set_txidle( struct mgsl_struct *info ) { u16 usc_idle_mode = IDLEMODE_FLAGS; /* Map API idle mode to USC register bits */ switch( info->idle_mode ){ case HDLC_TXIDLE_FLAGS: usc_idle_mode = IDLEMODE_FLAGS; break; case HDLC_TXIDLE_ALT_ZEROS_ONES: usc_idle_mode = IDLEMODE_ALT_ONE_ZERO; break; case HDLC_TXIDLE_ZEROS: usc_idle_mode = IDLEMODE_ZERO; break; case HDLC_TXIDLE_ONES: usc_idle_mode = IDLEMODE_ONE; break; case HDLC_TXIDLE_ALT_MARK_SPACE: usc_idle_mode = IDLEMODE_ALT_MARK_SPACE; break; case HDLC_TXIDLE_SPACE: usc_idle_mode = IDLEMODE_SPACE; break; case HDLC_TXIDLE_MARK: usc_idle_mode = IDLEMODE_MARK; break; } info->usc_idle_mode = usc_idle_mode; //usc_OutReg(info, TCSR, usc_idle_mode); info->tcsr_value &= ~IDLEMODE_MASK; /* clear idle mode bits */ info->tcsr_value += usc_idle_mode; usc_OutReg(info, TCSR, info->tcsr_value); /* * if SyncLink WAN adapter is running in external sync mode, the * transmitter has been set to Monosync in order to try to mimic * a true raw outbound bit stream. Monosync still sends an open/close * sync char at the start/end of a frame. Try to match those sync * patterns to the idle mode set here */ if ( info->params.mode == MGSL_MODE_RAW ) { unsigned char syncpat = 0; switch( info->idle_mode ) { case HDLC_TXIDLE_FLAGS: syncpat = 0x7e; break; case HDLC_TXIDLE_ALT_ZEROS_ONES: syncpat = 0x55; break; case HDLC_TXIDLE_ZEROS: case HDLC_TXIDLE_SPACE: syncpat = 0x00; break; case HDLC_TXIDLE_ONES: case HDLC_TXIDLE_MARK: syncpat = 0xff; break; case HDLC_TXIDLE_ALT_MARK_SPACE: syncpat = 0xaa; break; } usc_SetTransmitSyncChars(info,syncpat,syncpat); } } /* end of usc_set_txidle() */ /* usc_get_serial_signals() * * Query the adapter for the state of the V24 status (input) signals. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_get_serial_signals( struct mgsl_struct *info ) { u16 status; /* clear all serial signals except DTR and RTS */ info->serial_signals &= SerialSignal_DTR + SerialSignal_RTS; /* Read the Misc Interrupt status Register (MISR) to get */ /* the V24 status signals. */ status = usc_InReg( info, MISR ); /* set serial signal bits to reflect MISR */ if ( status & MISCSTATUS_CTS ) info->serial_signals |= SerialSignal_CTS; if ( status & MISCSTATUS_DCD ) info->serial_signals |= SerialSignal_DCD; if ( status & MISCSTATUS_RI ) info->serial_signals |= SerialSignal_RI; if ( status & MISCSTATUS_DSR ) info->serial_signals |= SerialSignal_DSR; } /* end of usc_get_serial_signals() */ /* usc_set_serial_signals() * * Set the state of DTR and RTS based on contents of * serial_signals member of device extension. * * Arguments: info pointer to device instance data * Return Value: None */ void usc_set_serial_signals( struct mgsl_struct *info ) { u16 Control; unsigned char V24Out = info->serial_signals; /* get the current value of the Port Control Register (PCR) */ Control = usc_InReg( info, PCR ); if ( V24Out & SerialSignal_RTS ) Control &= ~(BIT6); else Control |= BIT6; if ( V24Out & SerialSignal_DTR ) Control &= ~(BIT4); else Control |= BIT4; usc_OutReg( info, PCR, Control ); } /* end of usc_set_serial_signals() */ /* usc_enable_async_clock() * * Enable the async clock at the specified frequency. * * Arguments: info pointer to device instance data * data_rate data rate of clock in bps * 0 disables the AUX clock. * Return Value: None */ void usc_enable_async_clock( struct mgsl_struct *info, u32 data_rate ) { if ( data_rate ) { /* * Clock mode Control Register (CMCR) * * <15..14> 00 counter 1 Disabled * <13..12> 00 counter 0 Disabled * <11..10> 11 BRG1 Input is TxC Pin * <9..8> 11 BRG0 Input is TxC Pin * <7..6> 01 DPLL Input is BRG1 Output * <5..3> 100 TxCLK comes from BRG0 * <2..0> 100 RxCLK comes from BRG0 * * 0000 1111 0110 0100 = 0x0f64 */ usc_OutReg( info, CMCR, 0x0f64 ); /* * Write 16-bit Time Constant for BRG0 * Time Constant = (ClkSpeed / data_rate) - 1 * ClkSpeed = 921600 (ISA), 691200 (PCI) */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) usc_OutReg( info, TC0R, (u16)((691200/data_rate) - 1) ); else usc_OutReg( info, TC0R, (u16)((921600/data_rate) - 1) ); /* * Hardware Configuration Register (HCR) * Clear Bit 1, BRG0 mode = Continuous * Set Bit 0 to enable BRG0. */ usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) ); /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */ usc_OutReg( info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) ); } else { /* data rate == 0 so turn off BRG0 */ usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) ); } } /* end of usc_enable_async_clock() */ /* * Buffer Structures: * * Normal memory access uses virtual addresses that can make discontiguous * physical memory pages appear to be contiguous in the virtual address * space (the processors memory mapping handles the conversions). * * DMA transfers require physically contiguous memory. This is because * the DMA system controller and DMA bus masters deal with memory using * only physical addresses. * * This causes a problem under Windows NT when large DMA buffers are * needed. Fragmentation of the nonpaged pool prevents allocations of * physically contiguous buffers larger than the PAGE_SIZE. * * However the 16C32 supports Bus Master Scatter/Gather DMA which * allows DMA transfers to physically discontiguous buffers. Information * about each data transfer buffer is contained in a memory structure * called a 'buffer entry'. A list of buffer entries is maintained * to track and control the use of the data transfer buffers. * * To support this strategy we will allocate sufficient PAGE_SIZE * contiguous memory buffers to allow for the total required buffer * space. * * The 16C32 accesses the list of buffer entries using Bus Master * DMA. Control information is read from the buffer entries by the * 16C32 to control data transfers. status information is written to * the buffer entries by the 16C32 to indicate the status of completed * transfers. * * The CPU writes control information to the buffer entries to control * the 16C32 and reads status information from the buffer entries to * determine information about received and transmitted frames. * * Because the CPU and 16C32 (adapter) both need simultaneous access * to the buffer entries, the buffer entry memory is allocated with * HalAllocateCommonBuffer(). This restricts the size of the buffer * entry list to PAGE_SIZE. * * The actual data buffers on the other hand will only be accessed * by the CPU or the adapter but not by both simultaneously. This allows * Scatter/Gather packet based DMA procedures for using physically * discontiguous pages. */ /* * mgsl_reset_tx_dma_buffers() * * Set the count for all transmit buffers to 0 to indicate the * buffer is available for use and set the current buffer to the * first buffer. This effectively makes all buffers free and * discards any data in buffers. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info ) { unsigned int i; for ( i = 0; i < info->tx_buffer_count; i++ ) { *((unsigned long *)&(info->tx_buffer_list[i].count)) = 0; } info->current_tx_buffer = 0; info->start_tx_dma_buffer = 0; info->tx_dma_buffers_used = 0; info->get_tx_holding_index = 0; info->put_tx_holding_index = 0; info->tx_holding_count = 0; } /* end of mgsl_reset_tx_dma_buffers() */ /* * num_free_tx_dma_buffers() * * returns the number of free tx dma buffers available * * Arguments: info pointer to device instance data * Return Value: number of free tx dma buffers */ int num_free_tx_dma_buffers(struct mgsl_struct *info) { return info->tx_buffer_count - info->tx_dma_buffers_used; } /* * mgsl_reset_rx_dma_buffers() * * Set the count for all receive buffers to DMABUFFERSIZE * and set the current buffer to the first buffer. This effectively * makes all buffers free and discards any data in buffers. * * Arguments: info pointer to device instance data * Return Value: None */ void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info ) { unsigned int i; for ( i = 0; i < info->rx_buffer_count; i++ ) { *((unsigned long *)&(info->rx_buffer_list[i].count)) = DMABUFFERSIZE; // info->rx_buffer_list[i].count = DMABUFFERSIZE; // info->rx_buffer_list[i].status = 0; } info->current_rx_buffer = 0; } /* end of mgsl_reset_rx_dma_buffers() */ /* * mgsl_free_rx_frame_buffers() * * Free the receive buffers used by a received SDLC * frame such that the buffers can be reused. * * Arguments: * * info pointer to device instance data * StartIndex index of 1st receive buffer of frame * EndIndex index of last receive buffer of frame * * Return Value: None */ void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex ) { int Done = 0; DMABUFFERENTRY *pBufEntry; unsigned int Index; /* Starting with 1st buffer entry of the frame clear the status */ /* field and set the count field to DMA Buffer Size. */ Index = StartIndex; while( !Done ) { pBufEntry = &(info->rx_buffer_list[Index]); if ( Index == EndIndex ) { /* This is the last buffer of the frame! */ Done = 1; } /* reset current buffer for reuse */ // pBufEntry->status = 0; // pBufEntry->count = DMABUFFERSIZE; *((unsigned long *)&(pBufEntry->count)) = DMABUFFERSIZE; /* advance to next buffer entry in linked list */ Index++; if ( Index == info->rx_buffer_count ) Index = 0; } /* set current buffer to next buffer after last buffer of frame */ info->current_rx_buffer = Index; } /* end of free_rx_frame_buffers() */ /* mgsl_get_rx_frame() * * This function attempts to return a received SDLC frame from the * receive DMA buffers. Only frames received without errors are returned. * * Arguments: info pointer to device extension * Return Value: 1 if frame returned, otherwise 0 */ int mgsl_get_rx_frame(struct mgsl_struct *info) { unsigned int StartIndex, EndIndex; /* index of 1st and last buffers of Rx frame */ unsigned short status; DMABUFFERENTRY *pBufEntry; unsigned int framesize = 0; int ReturnCode = 0; unsigned long flags; struct tty_struct *tty = info->tty; int return_frame = 0; /* * current_rx_buffer points to the 1st buffer of the next available * receive frame. To find the last buffer of the frame look for * a non-zero status field in the buffer entries. (The status * field is set by the 16C32 after completing a receive frame. */ StartIndex = EndIndex = info->current_rx_buffer; while( !info->rx_buffer_list[EndIndex].status ) { /* * If the count field of the buffer entry is non-zero then * this buffer has not been used. (The 16C32 clears the count * field when it starts using the buffer.) If an unused buffer * is encountered then there are no frames available. */ if ( info->rx_buffer_list[EndIndex].count ) goto Cleanup; /* advance to next buffer entry in linked list */ EndIndex++; if ( EndIndex == info->rx_buffer_count ) EndIndex = 0; /* if entire list searched then no frame available */ if ( EndIndex == StartIndex ) { /* If this occurs then something bad happened, * all buffers have been 'used' but none mark * the end of a frame. Reset buffers and receiver. */ if ( info->rx_enabled ){ spin_lock_irqsave(&info->irq_spinlock,flags); usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } goto Cleanup; } } /* check status of receive frame */ status = info->rx_buffer_list[EndIndex].status; if ( status & (RXSTATUS_SHORT_FRAME + RXSTATUS_OVERRUN + RXSTATUS_CRC_ERROR + RXSTATUS_ABORT) ) { if ( status & RXSTATUS_SHORT_FRAME ) info->icount.rxshort++; else if ( status & RXSTATUS_ABORT ) info->icount.rxabort++; else if ( status & RXSTATUS_OVERRUN ) info->icount.rxover++; else { info->icount.rxcrc++; if ( info->params.crc_type & HDLC_CRC_RETURN_EX ) return_frame = 1; } framesize = 0; #ifdef CONFIG_SYNCLINK_SYNCPPP info->netstats.rx_errors++; info->netstats.rx_frame_errors++; #endif } else return_frame = 1; if ( return_frame ) { /* receive frame has no errors, get frame size. * The frame size is the starting value of the RCC (which was * set to 0xffff) minus the ending value of the RCC (decremented * once for each receive character) minus 2 for the 16-bit CRC. */ framesize = RCLRVALUE - info->rx_buffer_list[EndIndex].rcc; /* adjust frame size for CRC if any */ if ( info->params.crc_type == HDLC_CRC_16_CCITT ) framesize -= 2; else if ( info->params.crc_type == HDLC_CRC_32_CCITT ) framesize -= 4; } if ( debug_level >= DEBUG_LEVEL_BH ) printk("%s(%d):mgsl_get_rx_frame(%s) status=%04X size=%d\n", __FILE__,__LINE__,info->device_name,status,framesize); if ( debug_level >= DEBUG_LEVEL_DATA ) mgsl_trace_block(info,info->rx_buffer_list[StartIndex].virt_addr, MIN(framesize,DMABUFFERSIZE),0); if (framesize) { if ( ( (info->params.crc_type & HDLC_CRC_RETURN_EX) && ((framesize+1) > info->max_frame_size) ) || (framesize > info->max_frame_size) ) info->icount.rxlong++; else { /* copy dma buffer(s) to contiguous intermediate buffer */ int copy_count = framesize; int index = StartIndex; unsigned char *ptmp = info->intermediate_rxbuffer; if ( !(status & RXSTATUS_CRC_ERROR)) info->icount.rxok++; while(copy_count) { int partial_count; if ( copy_count > DMABUFFERSIZE ) partial_count = DMABUFFERSIZE; else partial_count = copy_count; pBufEntry = &(info->rx_buffer_list[index]); memcpy( ptmp, pBufEntry->virt_addr, partial_count ); ptmp += partial_count; copy_count -= partial_count; if ( ++index == info->rx_buffer_count ) index = 0; } if ( info->params.crc_type & HDLC_CRC_RETURN_EX ) { ++framesize; *ptmp = (status & RXSTATUS_CRC_ERROR ? RX_CRC_ERROR : RX_OK); if ( debug_level >= DEBUG_LEVEL_DATA ) printk("%s(%d):mgsl_get_rx_frame(%s) rx frame status=%d\n", __FILE__,__LINE__,info->device_name, *ptmp); } #ifdef CONFIG_SYNCLINK_SYNCPPP if (info->netcount) { /* pass frame to syncppp device */ mgsl_sppp_rx_done(info,info->intermediate_rxbuffer,framesize); } else #endif { /* Call the line discipline receive callback directly. */ if ( tty && tty->ldisc.receive_buf ) tty->ldisc.receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize); } } } /* Free the buffers used by this frame. */ mgsl_free_rx_frame_buffers( info, StartIndex, EndIndex ); ReturnCode = 1; Cleanup: if ( info->rx_enabled && info->rx_overflow ) { /* The receiver needs to restarted because of * a receive overflow (buffer or FIFO). If the * receive buffers are now empty, then restart receiver. */ if ( !info->rx_buffer_list[EndIndex].status && info->rx_buffer_list[EndIndex].count ) { spin_lock_irqsave(&info->irq_spinlock,flags); usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } return ReturnCode; } /* end of mgsl_get_rx_frame() */ /* mgsl_get_raw_rx_frame() * * This function attempts to return a received frame from the * receive DMA buffers when running in external loop mode. In this mode, * we will return at most one DMABUFFERSIZE frame to the application. * The USC receiver is triggering off of DCD going active to start a new * frame, and DCD going inactive to terminate the frame (similar to * processing a closing flag character). * * In this routine, we will return DMABUFFERSIZE "chunks" at a time. * If DCD goes inactive, the last Rx DMA Buffer will have a non-zero * status field and the RCC field will indicate the length of the * entire received frame. We take this RCC field and get the modulus * of RCC and DMABUFFERSIZE to determine if number of bytes in the * last Rx DMA buffer and return that last portion of the frame. * * Arguments: info pointer to device extension * Return Value: 1 if frame returned, otherwise 0 */ int mgsl_get_raw_rx_frame(struct mgsl_struct *info) { unsigned int CurrentIndex, NextIndex; unsigned short status; DMABUFFERENTRY *pBufEntry; unsigned int framesize = 0; int ReturnCode = 0; unsigned long flags; struct tty_struct *tty = info->tty; /* * current_rx_buffer points to the 1st buffer of the next available * receive frame. The status field is set by the 16C32 after * completing a receive frame. If the status field of this buffer * is zero, either the USC is still filling this buffer or this * is one of a series of buffers making up a received frame. * * If the count field of this buffer is zero, the USC is either * using this buffer or has used this buffer. Look at the count * field of the next buffer. If that next buffer's count is * non-zero, the USC is still actively using the current buffer. * Otherwise, if the next buffer's count field is zero, the * current buffer is complete and the USC is using the next * buffer. */ CurrentIndex = NextIndex = info->current_rx_buffer; ++NextIndex; if ( NextIndex == info->rx_buffer_count ) NextIndex = 0; if ( info->rx_buffer_list[CurrentIndex].status != 0 || (info->rx_buffer_list[CurrentIndex].count == 0 && info->rx_buffer_list[NextIndex].count == 0)) { /* * Either the status field of this dma buffer is non-zero * (indicating the last buffer of a receive frame) or the next * buffer is marked as in use -- implying this buffer is complete * and an intermediate buffer for this received frame. */ status = info->rx_buffer_list[CurrentIndex].status; if ( status & (RXSTATUS_SHORT_FRAME + RXSTATUS_OVERRUN + RXSTATUS_CRC_ERROR + RXSTATUS_ABORT) ) { if ( status & RXSTATUS_SHORT_FRAME ) info->icount.rxshort++; else if ( status & RXSTATUS_ABORT ) info->icount.rxabort++; else if ( status & RXSTATUS_OVERRUN ) info->icount.rxover++; else info->icount.rxcrc++; framesize = 0; } else { /* * A receive frame is available, get frame size and status. * * The frame size is the starting value of the RCC (which was * set to 0xffff) minus the ending value of the RCC (decremented * once for each receive character) minus 2 or 4 for the 16-bit * or 32-bit CRC. * * If the status field is zero, this is an intermediate buffer. * It's size is 4K. * * If the DMA Buffer Entry's Status field is non-zero, the * receive operation completed normally (ie: DCD dropped). The * RCC field is valid and holds the received frame size. * It is possible that the RCC field will be zero on a DMA buffer * entry with a non-zero status. This can occur if the total * frame size (number of bytes between the time DCD goes active * to the time DCD goes inactive) exceeds 65535 bytes. In this * case the 16C32 has underrun on the RCC count and appears to * stop updating this counter to let us know the actual received * frame size. If this happens (non-zero status and zero RCC), * simply return the entire RxDMA Buffer */ if ( status ) { /* * In the event that the final RxDMA Buffer is * terminated with a non-zero status and the RCC * field is zero, we interpret this as the RCC * having underflowed (received frame > 65535 bytes). * * Signal the event to the user by passing back * a status of RxStatus_CrcError returning the full * buffer and let the app figure out what data is * actually valid */ if ( info->rx_buffer_list[CurrentIndex].rcc ) framesize = RCLRVALUE - info->rx_buffer_list[CurrentIndex].rcc; else framesize = DMABUFFERSIZE; } else framesize = DMABUFFERSIZE; } if ( framesize > DMABUFFERSIZE ) { /* * if running in raw sync mode, ISR handler for * End Of Buffer events terminates all buffers at 4K. * If this frame size is said to be >4K, get the * actual number of bytes of the frame in this buffer. */ framesize = framesize % DMABUFFERSIZE; } if ( debug_level >= DEBUG_LEVEL_BH ) printk("%s(%d):mgsl_get_raw_rx_frame(%s) status=%04X size=%d\n", __FILE__,__LINE__,info->device_name,status,framesize); if ( debug_level >= DEBUG_LEVEL_DATA ) mgsl_trace_block(info,info->rx_buffer_list[CurrentIndex].virt_addr, MIN(framesize,DMABUFFERSIZE),0); if (framesize) { /* copy dma buffer(s) to contiguous intermediate buffer */ /* NOTE: we never copy more than DMABUFFERSIZE bytes */ pBufEntry = &(info->rx_buffer_list[CurrentIndex]); memcpy( info->intermediate_rxbuffer, pBufEntry->virt_addr, framesize); info->icount.rxok++; /* Call the line discipline receive callback directly. */ if ( tty && tty->ldisc.receive_buf ) tty->ldisc.receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize); } /* Free the buffers used by this frame. */ mgsl_free_rx_frame_buffers( info, CurrentIndex, CurrentIndex ); ReturnCode = 1; } if ( info->rx_enabled && info->rx_overflow ) { /* The receiver needs to restarted because of * a receive overflow (buffer or FIFO). If the * receive buffers are now empty, then restart receiver. */ if ( !info->rx_buffer_list[CurrentIndex].status && info->rx_buffer_list[CurrentIndex].count ) { spin_lock_irqsave(&info->irq_spinlock,flags); usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } return ReturnCode; } /* end of mgsl_get_raw_rx_frame() */ /* mgsl_load_tx_dma_buffer() * * Load the transmit DMA buffer with the specified data. * * Arguments: * * info pointer to device extension * Buffer pointer to buffer containing frame to load * BufferSize size in bytes of frame in Buffer * * Return Value: None */ void mgsl_load_tx_dma_buffer(struct mgsl_struct *info, const char *Buffer, unsigned int BufferSize) { unsigned short Copycount; unsigned int i = 0; DMABUFFERENTRY *pBufEntry; if ( debug_level >= DEBUG_LEVEL_DATA ) mgsl_trace_block(info,Buffer, MIN(BufferSize,DMABUFFERSIZE), 1); if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) { /* set CMR:13 to start transmit when * next GoAhead (abort) is received */ info->cmr_value |= BIT13; } /* begin loading the frame in the next available tx dma * buffer, remember it's starting location for setting * up tx dma operation */ i = info->current_tx_buffer; info->start_tx_dma_buffer = i; /* Setup the status and RCC (Frame Size) fields of the 1st */ /* buffer entry in the transmit DMA buffer list. */ info->tx_buffer_list[i].status = info->cmr_value & 0xf000; info->tx_buffer_list[i].rcc = BufferSize; info->tx_buffer_list[i].count = BufferSize; /* Copy frame data from 1st source buffer to the DMA buffers. */ /* The frame data may span multiple DMA buffers. */ while( BufferSize ){ /* Get a pointer to next DMA buffer entry. */ pBufEntry = &info->tx_buffer_list[i++]; if ( i == info->tx_buffer_count ) i=0; /* Calculate the number of bytes that can be copied from */ /* the source buffer to this DMA buffer. */ if ( BufferSize > DMABUFFERSIZE ) Copycount = DMABUFFERSIZE; else Copycount = BufferSize; /* Actually copy data from source buffer to DMA buffer. */ /* Also set the data count for this individual DMA buffer. */ if ( info->bus_type == MGSL_BUS_TYPE_PCI ) mgsl_load_pci_memory(pBufEntry->virt_addr, Buffer,Copycount); else memcpy(pBufEntry->virt_addr, Buffer, Copycount); pBufEntry->count = Copycount; /* Advance source pointer and reduce remaining data count. */ Buffer += Copycount; BufferSize -= Copycount; ++info->tx_dma_buffers_used; } /* remember next available tx dma buffer */ info->current_tx_buffer = i; } /* end of mgsl_load_tx_dma_buffer() */ /* * mgsl_register_test() * * Performs a register test of the 16C32. * * Arguments: info pointer to device instance data * Return Value: TRUE if test passed, otherwise FALSE */ BOOLEAN mgsl_register_test( struct mgsl_struct *info ) { static unsigned short BitPatterns[] = { 0x0000, 0xffff, 0xaaaa, 0x5555, 0x1234, 0x6969, 0x9696, 0x0f0f }; static unsigned int Patterncount = sizeof(BitPatterns)/sizeof(unsigned short); unsigned int i; BOOLEAN rc = TRUE; unsigned long flags; spin_lock_irqsave(&info->irq_spinlock,flags); usc_reset(info); /* Verify the reset state of some registers. */ if ( (usc_InReg( info, SICR ) != 0) || (usc_InReg( info, IVR ) != 0) || (usc_InDmaReg( info, DIVR ) != 0) ){ rc = FALSE; } if ( rc == TRUE ){ /* Write bit patterns to various registers but do it out of */ /* sync, then read back and verify values. */ for ( i = 0 ; i < Patterncount ; i++ ) { usc_OutReg( info, TC0R, BitPatterns[i] ); usc_OutReg( info, TC1R, BitPatterns[(i+1)%Patterncount] ); usc_OutReg( info, TCLR, BitPatterns[(i+2)%Patterncount] ); usc_OutReg( info, RCLR, BitPatterns[(i+3)%Patterncount] ); usc_OutReg( info, RSR, BitPatterns[(i+4)%Patterncount] ); usc_OutDmaReg( info, TBCR, BitPatterns[(i+5)%Patterncount] ); if ( (usc_InReg( info, TC0R ) != BitPatterns[i]) || (usc_InReg( info, TC1R ) != BitPatterns[(i+1)%Patterncount]) || (usc_InReg( info, TCLR ) != BitPatterns[(i+2)%Patterncount]) || (usc_InReg( info, RCLR ) != BitPatterns[(i+3)%Patterncount]) || (usc_InReg( info, RSR ) != BitPatterns[(i+4)%Patterncount]) || (usc_InDmaReg( info, TBCR ) != BitPatterns[(i+5)%Patterncount]) ){ rc = FALSE; break; } } } usc_reset(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); return rc; } /* end of mgsl_register_test() */ /* mgsl_irq_test() Perform interrupt test of the 16C32. * * Arguments: info pointer to device instance data * Return Value: TRUE if test passed, otherwise FALSE */ BOOLEAN mgsl_irq_test( struct mgsl_struct *info ) { unsigned long EndTime; unsigned long flags; spin_lock_irqsave(&info->irq_spinlock,flags); usc_reset(info); /* * Setup 16C32 to interrupt on TxC pin (14MHz clock) transition. * The ISR sets irq_occurred to 1. */ info->irq_occurred = FALSE; /* Enable INTEN gate for ISA adapter (Port 6, Bit12) */ /* Enable INTEN (Port 6, Bit12) */ /* This connects the IRQ request signal to the ISA bus */ /* on the ISA adapter. This has no effect for the PCI adapter */ usc_OutReg( info, PCR, (unsigned short)((usc_InReg(info, PCR) | BIT13) & ~BIT12) ); usc_EnableMasterIrqBit(info); usc_EnableInterrupts(info, IO_PIN); usc_ClearIrqPendingBits(info, IO_PIN); usc_UnlatchIostatusBits(info, MISCSTATUS_TXC_LATCHED); usc_EnableStatusIrqs(info, SICR_TXC_ACTIVE + SICR_TXC_INACTIVE); spin_unlock_irqrestore(&info->irq_spinlock,flags); EndTime=100; while( EndTime-- && !info->irq_occurred ) { set_current_state(TASK_INTERRUPTIBLE); schedule_timeout(jiffies_from_ms(10)); } spin_lock_irqsave(&info->irq_spinlock,flags); usc_reset(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); if ( !info->irq_occurred ) return FALSE; else return TRUE; } /* end of mgsl_irq_test() */ /* mgsl_dma_test() * * Perform a DMA test of the 16C32. A small frame is * transmitted via DMA from a transmit buffer to a receive buffer * using single buffer DMA mode. * * Arguments: info pointer to device instance data * Return Value: TRUE if test passed, otherwise FALSE */ BOOLEAN mgsl_dma_test( struct mgsl_struct *info ) { unsigned short FifoLevel; unsigned long phys_addr; unsigned int FrameSize; unsigned int i; char *TmpPtr; BOOLEAN rc = TRUE; unsigned short status=0; unsigned long EndTime; unsigned long flags; MGSL_PARAMS tmp_params; /* save current port options */ memcpy(&tmp_params,&info->params,sizeof(MGSL_PARAMS)); /* load default port options */ memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS)); #define TESTFRAMESIZE 40 spin_lock_irqsave(&info->irq_spinlock,flags); /* setup 16C32 for SDLC DMA transfer mode */ usc_reset(info); usc_set_sdlc_mode(info); usc_enable_loopback(info,1); /* Reprogram the RDMR so that the 16C32 does NOT clear the count * field of the buffer entry after fetching buffer address. This * way we can detect a DMA failure for a DMA read (which should be * non-destructive to system memory) before we try and write to * memory (where a failure could corrupt system memory). */ /* Receive DMA mode Register (RDMR) * * <15..14> 11 DMA mode = Linked List Buffer mode * <13> 1 RSBinA/L = store Rx status Block in List entry * <12> 0 1 = Clear count of List Entry after fetching * <11..10> 00 Address mode = Increment * <9> 1 Terminate Buffer on RxBound * <8> 0 Bus Width = 16bits * <7..0> ? status Bits (write as 0s) * * 1110 0010 0000 0000 = 0xe200 */ usc_OutDmaReg( info, RDMR, 0xe200 ); spin_unlock_irqrestore(&info->irq_spinlock,flags); /* SETUP TRANSMIT AND RECEIVE DMA BUFFERS */ FrameSize = TESTFRAMESIZE; /* setup 1st transmit buffer entry: */ /* with frame size and transmit control word */ info->tx_buffer_list[0].count = FrameSize; info->tx_buffer_list[0].rcc = FrameSize; info->tx_buffer_list[0].status = 0x4000; /* build a transmit frame in 1st transmit DMA buffer */ TmpPtr = info->tx_buffer_list[0].virt_addr; for (i = 0; i < FrameSize; i++ ) *TmpPtr++ = i; /* setup 1st receive buffer entry: */ /* clear status, set max receive buffer size */ info->rx_buffer_list[0].status = 0; info->rx_buffer_list[0].count = FrameSize + 4; /* zero out the 1st receive buffer */ memset( info->rx_buffer_list[0].virt_addr, 0, FrameSize + 4 ); /* Set count field of next buffer entries to prevent */ /* 16C32 from using buffers after the 1st one. */ info->tx_buffer_list[1].count = 0; info->rx_buffer_list[1].count = 0; /***************************/ /* Program 16C32 receiver. */ /***************************/ spin_lock_irqsave(&info->irq_spinlock,flags); /* setup DMA transfers */ usc_RTCmd( info, RTCmd_PurgeRxFifo ); /* program 16C32 receiver with physical address of 1st DMA buffer entry */ phys_addr = info->rx_buffer_list[0].phys_entry; usc_OutDmaReg( info, NRARL, (unsigned short)phys_addr ); usc_OutDmaReg( info, NRARU, (unsigned short)(phys_addr >> 16) ); /* Clear the Rx DMA status bits (read RDMR) and start channel */ usc_InDmaReg( info, RDMR ); usc_DmaCmd( info, DmaCmd_InitRxChannel ); /* Enable Receiver (RMR <1..0> = 10) */ usc_OutReg( info, RMR, (unsigned short)((usc_InReg(info, RMR) & 0xfffc) | 0x0002) ); spin_unlock_irqrestore(&info->irq_spinlock,flags); /*************************************************************/ /* WAIT FOR RECEIVER TO DMA ALL PARAMETERS FROM BUFFER ENTRY */ /*************************************************************/ /* Wait 100ms for interrupt. */ EndTime = jiffies + jiffies_from_ms(100); for(;;) { if (time_after(jiffies, EndTime)) { rc = FALSE; break; } spin_lock_irqsave(&info->irq_spinlock,flags); status = usc_InDmaReg( info, RDMR ); spin_unlock_irqrestore(&info->irq_spinlock,flags); if ( !(status & BIT4) && (status & BIT5) ) { /* INITG (BIT 4) is inactive (no entry read in progress) AND */ /* BUSY (BIT 5) is active (channel still active). */ /* This means the buffer entry read has completed. */ break; } } /******************************/ /* Program 16C32 transmitter. */ /******************************/ spin_lock_irqsave(&info->irq_spinlock,flags); /* Program the Transmit Character Length Register (TCLR) */ /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */ usc_OutReg( info, TCLR, (unsigned short)info->tx_buffer_list[0].count ); usc_RTCmd( info, RTCmd_PurgeTxFifo ); /* Program the address of the 1st DMA Buffer Entry in linked list */ phys_addr = info->tx_buffer_list[0].phys_entry; usc_OutDmaReg( info, NTARL, (unsigned short)phys_addr ); usc_OutDmaReg( info, NTARU, (unsigned short)(phys_addr >> 16) ); /* unlatch Tx status bits, and start transmit channel. */ usc_OutReg( info, TCSR, (unsigned short)(( usc_InReg(info, TCSR) & 0x0f00) | 0xfa) ); usc_DmaCmd( info, DmaCmd_InitTxChannel ); /* wait for DMA controller to fill transmit FIFO */ usc_TCmd( info, TCmd_SelectTicrTxFifostatus ); spin_unlock_irqrestore(&info->irq_spinlock,flags); /**********************************/ /* WAIT FOR TRANSMIT FIFO TO FILL */ /**********************************/ /* Wait 100ms */ EndTime = jiffies + jiffies_from_ms(100); for(;;) { if (time_after(jiffies, EndTime)) { rc = FALSE; break; } spin_lock_irqsave(&info->irq_spinlock,flags); FifoLevel = usc_InReg(info, TICR) >> 8; spin_unlock_irqrestore(&info->irq_spinlock,flags); if ( FifoLevel < 16 ) break; else if ( FrameSize < 32 ) { /* This frame is smaller than the entire transmit FIFO */ /* so wait for the entire frame to be loaded. */ if ( FifoLevel <= (32 - FrameSize) ) break; } } if ( rc == TRUE ) { /* Enable 16C32 transmitter. */ spin_lock_irqsave(&info->irq_spinlock,flags); /* Transmit mode Register (TMR), <1..0> = 10, Enable Transmitter */ usc_TCmd( info, TCmd_SendFrame ); usc_OutReg( info, TMR, (unsigned short)((usc_InReg(info, TMR) & 0xfffc) | 0x0002) ); spin_unlock_irqrestore(&info->irq_spinlock,flags); /******************************/ /* WAIT FOR TRANSMIT COMPLETE */ /******************************/ /* Wait 100ms */ EndTime = jiffies + jiffies_from_ms(100); /* While timer not expired wait for transmit complete */ spin_lock_irqsave(&info->irq_spinlock,flags); status = usc_InReg( info, TCSR ); spin_unlock_irqrestore(&info->irq_spinlock,flags); while ( !(status & (BIT6+BIT5+BIT4+BIT2+BIT1)) ) { if (time_after(jiffies, EndTime)) { rc = FALSE; break; } spin_lock_irqsave(&info->irq_spinlock,flags); status = usc_InReg( info, TCSR ); spin_unlock_irqrestore(&info->irq_spinlock,flags); } } if ( rc == TRUE ){ /* CHECK FOR TRANSMIT ERRORS */ if ( status & (BIT5 + BIT1) ) rc = FALSE; } if ( rc == TRUE ) { /* WAIT FOR RECEIVE COMPLETE */ /* Wait 100ms */ EndTime = jiffies + jiffies_from_ms(100); /* Wait for 16C32 to write receive status to buffer entry. */ status=info->rx_buffer_list[0].status; while ( status == 0 ) { if (time_after(jiffies, EndTime)) { rc = FALSE; break; } status=info->rx_buffer_list[0].status; } } if ( rc == TRUE ) { /* CHECK FOR RECEIVE ERRORS */ status = info->rx_buffer_list[0].status; if ( status & (BIT8 + BIT3 + BIT1) ) { /* receive error has occured */ rc = FALSE; } else { if ( memcmp( info->tx_buffer_list[0].virt_addr , info->rx_buffer_list[0].virt_addr, FrameSize ) ){ rc = FALSE; } } } spin_lock_irqsave(&info->irq_spinlock,flags); usc_reset( info ); spin_unlock_irqrestore(&info->irq_spinlock,flags); /* restore current port options */ memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS)); return rc; } /* end of mgsl_dma_test() */ /* mgsl_adapter_test() * * Perform the register, IRQ, and DMA tests for the 16C32. * * Arguments: info pointer to device instance data * Return Value: 0 if success, otherwise -ENODEV */ int mgsl_adapter_test( struct mgsl_struct *info ) { if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):Testing device %s\n", __FILE__,__LINE__,info->device_name ); if ( !mgsl_register_test( info ) ) { info->init_error = DiagStatus_AddressFailure; printk( "%s(%d):Register test failure for device %s Addr=%04X\n", __FILE__,__LINE__,info->device_name, (unsigned short)(info->io_base) ); return -ENODEV; } if ( !mgsl_irq_test( info ) ) { info->init_error = DiagStatus_IrqFailure; printk( "%s(%d):Interrupt test failure for device %s IRQ=%d\n", __FILE__,__LINE__,info->device_name, (unsigned short)(info->irq_level) ); return -ENODEV; } if ( !mgsl_dma_test( info ) ) { info->init_error = DiagStatus_DmaFailure; printk( "%s(%d):DMA test failure for device %s DMA=%d\n", __FILE__,__LINE__,info->device_name, (unsigned short)(info->dma_level) ); return -ENODEV; } if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):device %s passed diagnostics\n", __FILE__,__LINE__,info->device_name ); return 0; } /* end of mgsl_adapter_test() */ /* mgsl_memory_test() * * Test the shared memory on a PCI adapter. * * Arguments: info pointer to device instance data * Return Value: TRUE if test passed, otherwise FALSE */ BOOLEAN mgsl_memory_test( struct mgsl_struct *info ) { static unsigned long BitPatterns[] = { 0x0, 0x55555555, 0xaaaaaaaa, 0x66666666, 0x99999999, 0xffffffff, 0x12345678 }; unsigned long Patterncount = sizeof(BitPatterns)/sizeof(unsigned long); unsigned long i; unsigned long TestLimit = SHARED_MEM_ADDRESS_SIZE/sizeof(unsigned long); unsigned long * TestAddr; if ( info->bus_type != MGSL_BUS_TYPE_PCI ) return TRUE; TestAddr = (unsigned long *)info->memory_base; /* Test data lines with test pattern at one location. */ for ( i = 0 ; i < Patterncount ; i++ ) { *TestAddr = BitPatterns[i]; if ( *TestAddr != BitPatterns[i] ) return FALSE; } /* Test address lines with incrementing pattern over */ /* entire address range. */ for ( i = 0 ; i < TestLimit ; i++ ) { *TestAddr = i * 4; TestAddr++; } TestAddr = (unsigned long *)info->memory_base; for ( i = 0 ; i < TestLimit ; i++ ) { if ( *TestAddr != i * 4 ) return FALSE; TestAddr++; } memset( info->memory_base, 0, SHARED_MEM_ADDRESS_SIZE ); return TRUE; } /* End Of mgsl_memory_test() */ /* mgsl_load_pci_memory() * * Load a large block of data into the PCI shared memory. * Use this instead of memcpy() or memmove() to move data * into the PCI shared memory. * * Notes: * * This function prevents the PCI9050 interface chip from hogging * the adapter local bus, which can starve the 16C32 by preventing * 16C32 bus master cycles. * * The PCI9050 documentation says that the 9050 will always release * control of the local bus after completing the current read * or write operation. * * It appears that as long as the PCI9050 write FIFO is full, the * PCI9050 treats all of the writes as a single burst transaction * and will not release the bus. This causes DMA latency problems * at high speeds when copying large data blocks to the shared * memory. * * This function in effect, breaks the a large shared memory write * into multiple transations by interleaving a shared memory read * which will flush the write FIFO and 'complete' the write * transation. This allows any pending DMA request to gain control * of the local bus in a timely fasion. * * Arguments: * * TargetPtr pointer to target address in PCI shared memory * SourcePtr pointer to source buffer for data * count count in bytes of data to copy * * Return Value: None */ void mgsl_load_pci_memory( char* TargetPtr, const char* SourcePtr, unsigned short count ) { /* 16 32-bit writes @ 60ns each = 960ns max latency on local bus */ #define PCI_LOAD_INTERVAL 64 unsigned short Intervalcount = count / PCI_LOAD_INTERVAL; unsigned short Index; unsigned long Dummy; for ( Index = 0 ; Index < Intervalcount ; Index++ ) { memcpy(TargetPtr, SourcePtr, PCI_LOAD_INTERVAL); Dummy = *((volatile unsigned long *)TargetPtr); TargetPtr += PCI_LOAD_INTERVAL; SourcePtr += PCI_LOAD_INTERVAL; } memcpy( TargetPtr, SourcePtr, count % PCI_LOAD_INTERVAL ); } /* End Of mgsl_load_pci_memory() */ void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit) { int i; int linecount; if (xmit) printk("%s tx data:\n",info->device_name); else printk("%s rx data:\n",info->device_name); while(count) { if (count > 16) linecount = 16; else linecount = count; for(i=0;i<linecount;i++) printk("%02X ",(unsigned char)data[i]); for(;i<17;i++) printk(" "); for(i=0;i<linecount;i++) { if (data[i]>=040 && data[i]<=0176) printk("%c",data[i]); else printk("."); } printk("\n"); data += linecount; count -= linecount; } } /* end of mgsl_trace_block() */ /* mgsl_tx_timeout() * * called when HDLC frame times out * update stats and do tx completion processing * * Arguments: context pointer to device instance data * Return Value: None */ void mgsl_tx_timeout(unsigned long context) { struct mgsl_struct *info = (struct mgsl_struct*)context; unsigned long flags; if ( debug_level >= DEBUG_LEVEL_INFO ) printk( "%s(%d):mgsl_tx_timeout(%s)\n", __FILE__,__LINE__,info->device_name); if(info->tx_active && (info->params.mode == MGSL_MODE_HDLC || info->params.mode == MGSL_MODE_RAW) ) { info->icount.txtimeout++; } spin_lock_irqsave(&info->irq_spinlock,flags); info->tx_active = 0; info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE ) usc_loopmode_cancel_transmit( info ); spin_unlock_irqrestore(&info->irq_spinlock,flags); #ifdef CONFIG_SYNCLINK_SYNCPPP if (info->netcount) mgsl_sppp_tx_done(info); else #endif mgsl_bh_transmit(info); } /* end of mgsl_tx_timeout() */ /* signal that there are no more frames to send, so that * line is 'released' by echoing RxD to TxD when current * transmission is complete (or immediately if no tx in progress). */ static int mgsl_loopmode_send_done( struct mgsl_struct * info ) { unsigned long flags; spin_lock_irqsave(&info->irq_spinlock,flags); if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) { if (info->tx_active) info->loopmode_send_done_requested = TRUE; else usc_loopmode_send_done(info); } spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } /* release the line by echoing RxD to TxD * upon completion of a transmit frame */ void usc_loopmode_send_done( struct mgsl_struct * info ) { info->loopmode_send_done_requested = FALSE; /* clear CMR:13 to 0 to start echoing RxData to TxData */ info->cmr_value &= ~BIT13; usc_OutReg(info, CMR, info->cmr_value); } /* abort a transmit in progress while in HDLC LoopMode */ void usc_loopmode_cancel_transmit( struct mgsl_struct * info ) { /* reset tx dma channel and purge TxFifo */ usc_RTCmd( info, RTCmd_PurgeTxFifo ); usc_DmaCmd( info, DmaCmd_ResetTxChannel ); usc_loopmode_send_done( info ); } /* for HDLC/SDLC LoopMode, setting CMR:13 after the transmitter is enabled * is an Insert Into Loop action. Upon receipt of a GoAhead sequence (RxAbort) * we must clear CMR:13 to begin repeating TxData to RxData */ void usc_loopmode_insert_request( struct mgsl_struct * info ) { info->loopmode_insert_requested = TRUE; /* enable RxAbort irq. On next RxAbort, clear CMR:13 to * begin repeating TxData on RxData (complete insertion) */ usc_OutReg( info, RICR, (usc_InReg( info, RICR ) | RXSTATUS_ABORT_RECEIVED ) ); /* set CMR:13 to insert into loop on next GoAhead (RxAbort) */ info->cmr_value |= BIT13; usc_OutReg(info, CMR, info->cmr_value); } /* return 1 if station is inserted into the loop, otherwise 0 */ int usc_loopmode_active( struct mgsl_struct * info) { return usc_InReg( info, CCSR ) & BIT7 ? 1 : 0 ; } /* return 1 if USC is in loop send mode, otherwise 0 */ int usc_loopmode_send_active( struct mgsl_struct * info ) { return usc_InReg( info, CCSR ) & BIT6 ? 1 : 0 ; } #ifdef CONFIG_SYNCLINK_SYNCPPP /* syncppp net device routines */ void mgsl_sppp_init(struct mgsl_struct *info) { struct net_device *d; sprintf(info->netname,"mgsl%d",info->line); info->if_ptr = &info->pppdev; info->netdev = info->pppdev.dev = &info->netdevice; sppp_attach(&info->pppdev); d = info->netdev; strcpy(d->name,info->netname); d->base_addr = info->io_base; d->irq = info->irq_level; d->dma = info->dma_level; d->priv = info; d->init = NULL; d->open = mgsl_sppp_open; d->stop = mgsl_sppp_close; d->hard_start_xmit = mgsl_sppp_tx; d->do_ioctl = mgsl_sppp_ioctl; d->get_stats = mgsl_net_stats; d->tx_timeout = mgsl_sppp_tx_timeout; d->watchdog_timeo = 10*HZ; #if LINUX_VERSION_CODE < VERSION(2,4,4) dev_init_buffers(d); #endif if (register_netdev(d) == -1) { printk(KERN_WARNING "%s: register_netdev failed.\n", d->name); sppp_detach(info->netdev); return; } if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_init()\n"); } void mgsl_sppp_delete(struct mgsl_struct *info) { if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_delete(%s)\n",info->netname); sppp_detach(info->netdev); unregister_netdev(info->netdev); } int mgsl_sppp_open(struct net_device *d) { struct mgsl_struct *info = d->priv; int err; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_open(%s)\n",info->netname); spin_lock_irqsave(&info->netlock, flags); if (info->count != 0 || info->netcount != 0) { printk(KERN_WARNING "%s: sppp_open returning busy\n", info->netname); spin_unlock_irqrestore(&info->netlock, flags); return -EBUSY; } info->netcount=1; MOD_INC_USE_COUNT; spin_unlock_irqrestore(&info->netlock, flags); /* claim resources and init adapter */ if ((err = startup(info)) != 0) goto open_fail; /* allow syncppp module to do open processing */ if ((err = sppp_open(d)) != 0) { shutdown(info); goto open_fail; } info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR; mgsl_program_hw(info); d->trans_start = jiffies; netif_start_queue(d); return 0; open_fail: spin_lock_irqsave(&info->netlock, flags); info->netcount=0; MOD_DEC_USE_COUNT; spin_unlock_irqrestore(&info->netlock, flags); return err; } void mgsl_sppp_tx_timeout(struct net_device *dev) { struct mgsl_struct *info = dev->priv; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_tx_timeout(%s)\n",info->netname); info->netstats.tx_errors++; info->netstats.tx_aborted_errors++; spin_lock_irqsave(&info->irq_spinlock,flags); usc_stop_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); netif_wake_queue(dev); } int mgsl_sppp_tx(struct sk_buff *skb, struct net_device *dev) { struct mgsl_struct *info = dev->priv; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_tx(%s)\n",info->netname); netif_stop_queue(dev); info->xmit_cnt = skb->len; mgsl_load_tx_dma_buffer(info, skb->data, skb->len); info->netstats.tx_packets++; info->netstats.tx_bytes += skb->len; dev_kfree_skb(skb); dev->trans_start = jiffies; spin_lock_irqsave(&info->irq_spinlock,flags); if (!info->tx_active) usc_start_transmitter(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); return 0; } int mgsl_sppp_close(struct net_device *d) { struct mgsl_struct *info = d->priv; unsigned long flags; if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_close(%s)\n",info->netname); /* shutdown adapter and release resources */ shutdown(info); /* allow syncppp to do close processing */ sppp_close(d); netif_stop_queue(d); spin_lock_irqsave(&info->netlock, flags); info->netcount=0; MOD_DEC_USE_COUNT; spin_unlock_irqrestore(&info->netlock, flags); return 0; } void mgsl_sppp_rx_done(struct mgsl_struct *info, char *buf, int size) { struct sk_buff *skb = dev_alloc_skb(size); if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_sppp_rx_done(%s)\n",info->netname); if (skb == NULL) { printk(KERN_NOTICE "%s: cant alloc skb, dropping packet\n", info->netname); info->netstats.rx_dropped++; return; } memcpy(skb_put(skb, size),buf,size); skb->protocol = htons(ETH_P_WAN_PPP); skb->dev = info->netdev; skb->mac.raw = skb->data; info->netstats.rx_packets++; info->netstats.rx_bytes += size; netif_rx(skb); info->netdev->trans_start = jiffies; } void mgsl_sppp_tx_done(struct mgsl_struct *info) { if (netif_queue_stopped(info->netdev)) netif_wake_queue(info->netdev); } struct net_device_stats *mgsl_net_stats(struct net_device *dev) { struct mgsl_struct *info = dev->priv; if (debug_level >= DEBUG_LEVEL_INFO) printk("mgsl_net_stats(%s)\n",info->netname); return &info->netstats; } int mgsl_sppp_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) { struct mgsl_struct *info = (struct mgsl_struct *)dev->priv; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_ioctl %s cmd=%08X\n", __FILE__,__LINE__, info->netname, cmd ); return sppp_do_ioctl(dev, ifr, cmd); } #endif /* ifdef CONFIG_SYNCLINK_SYNCPPP */ static int __init synclink_init_one (struct pci_dev *dev, const struct pci_device_id *ent) { struct mgsl_struct *info; if (pci_enable_device(dev)) { printk("error enabling pci device %p\n", dev); return -EIO; } if (!(info = mgsl_allocate_device())) { printk("can't allocate device instance data.\n"); return -EIO; } /* Copy user configuration info to device instance data */ info->io_base = pci_resource_start(dev, 2); info->irq_level = dev->irq; info->phys_memory_base = pci_resource_start(dev, 3); /* Because veremap only works on page boundaries we must map * a larger area than is actually implemented for the LCR * memory range. We map a full page starting at the page boundary. */ info->phys_lcr_base = pci_resource_start(dev, 0); info->lcr_offset = info->phys_lcr_base & (PAGE_SIZE-1); info->phys_lcr_base &= ~(PAGE_SIZE-1); info->bus_type = MGSL_BUS_TYPE_PCI; info->io_addr_size = 8; info->irq_flags = SA_SHIRQ; if (dev->device == 0x0210) { /* Version 1 PCI9030 based universal PCI adapter */ info->misc_ctrl_value = 0x007c4080; info->hw_version = 1; } else { /* Version 0 PCI9050 based 5V PCI adapter * A PCI9050 bug prevents reading LCR registers if * LCR base address bit 7 is set. Maintain shadow * value so we can write to LCR misc control reg. */ info->misc_ctrl_value = 0x087e4546; info->hw_version = 0; } mgsl_add_device(info); return 0; } static void __devexit synclink_remove_one (struct pci_dev *dev) { }