URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [net/] [fc/] [tach.h] - Rev 1765
Compare with Previous | Blame | View Log
/********************************************************************** * Defines for the Tachyon Fibre Channel Controller and the Interphase * (i)chip TPI. *********************************************************************/ #ifndef _TACH_H #define _TACH_H #define MY_PAGE_SIZE 4096 #define REPLICATE 0xFF #define MAX_NODES 127 #define BROADCAST 0xFFFFFF #define BROADCAST_ADDR 0xFFFFFFFFFFFF #define LOGIN_COMPLETED 2 #define LOGIN_ATTEMPTED 1 #define LOGIN_NOT_ATTEMPTED 0 #define TRUE 1 #define FALSE 0 #define TACHYON_LIMIT 0x01EF #define TACHYON_OFFSET 0x200 /* Offsets to the (i) chip */ #define ICHIP_HW_CONTROL_REG_OFF (0x080 - TACHYON_OFFSET) #define ICHIP_HW_STATUS_REG_OFF (0x084 - TACHYON_OFFSET) #define ICHIP_HW_ADDR_MASK_REG_OFF (0x090 - TACHYON_OFFSET) /* (i)chip Hardware Control Register defines */ #define ICHIP_HCR_RESET 0x01 #define ICHIP_HCR_DERESET 0x0 #define ICHIP_HCR_ENABLE_INTA 0x0000003E #define ICHIP_HCR_ENABLE_INTB 0x003E0000 #define ICHIP_HCR_IWDATA_FIFO 0x800000 /* (i)chip Hardware Status Register defines */ #define ICHIP_HSR_INT_LATCH 0x02 /* (i)chip Hardware Address Mask Register defines */ #define ICHIP_HAMR_BYTE_SWAP_ADDR_TR 0x08 #define ICHIP_HAMR_BYTE_SWAP_NO_ADDR_TR 0x04 /* NOVRAM defines */ #define IPH5526_NOVRAM_SIZE 64 /* Offsets for the registers that correspond to the * Qs on the Tachyon (As defined in the Tachyon Manual). */ /* Outbound Command Queue (OCQ). */ #define OCQ_BASE_REGISTER_OFFSET 0x000 #define OCQ_LENGTH_REGISTER_OFFSET 0x004 #define OCQ_PRODUCER_REGISTER_OFFSET 0x008 #define OCQ_CONSUMER_REGISTER_OFFSET 0x00C /* Inbound Message Queue (IMQ). */ #define IMQ_BASE_REGISTER_OFFSET 0x080 #define IMQ_LENGTH_REGISTER_OFFSET 0x084 #define IMQ_CONSUMER_REGISTER_OFFSET 0x088 #define IMQ_PRODUCER_REGISTER_OFFSET 0x08C /* Multiframe Sequence Buffer Queue (MFSBQ) */ #define MFSBQ_BASE_REGISTER_OFFSET 0x0C0 #define MFSBQ_LENGTH_REGISTER_OFFSET 0x0C4 #define MFSBQ_PRODUCER_REGISTER_OFFSET 0x0C8 #define MFSBQ_CONSUMER_REGISTER_OFFSET 0x0CC #define MFS_LENGTH_REGISTER_OFFSET 0x0D0 /* Single Frame Sequence Buffer Queue (SFSBQ) */ #define SFSBQ_BASE_REGISTER_OFFSET 0x100 #define SFSBQ_LENGTH_REGISTER_OFFSET 0x104 #define SFSBQ_PRODUCER_REGISTER_OFFSET 0x108 #define SFSBQ_CONSUMER_REGISTER_OFFSET 0x10C #define SFS_LENGTH_REGISTER_OFFSET 0x110 /* SCSI Exchange State Table (SEST) */ #define SEST_BASE_REGISTER_OFFSET 0x140 #define SEST_LENGTH_REGISTER_OFFSET 0x144 #define SCSI_LENGTH_REGISTER_OFFSET 0x148 /* Length of the various Qs */ #define NO_OF_ENTRIES 8 #define OCQ_LENGTH (MY_PAGE_SIZE/32) #define IMQ_LENGTH (MY_PAGE_SIZE/32) #define MFSBQ_LENGTH 8 #define SFSBQ_LENGTH 8 #define SEST_LENGTH MY_PAGE_SIZE /* Size of the various buffers. */ #define TACH_FRAME_SIZE 2048 #define MFS_BUFFER_SIZE TACH_FRAME_SIZE #define SFS_BUFFER_SIZE (TACH_FRAME_SIZE + TACHYON_HEADER_LEN) #define SEST_BUFFER_SIZE 512 #define TACH_HEADER_SIZE 64 #define NO_OF_TACH_HEADERS ((MY_PAGE_SIZE)/TACH_HEADER_SIZE) #define NO_OF_FCP_CMNDS (MY_PAGE_SIZE/32) #define SDB_SIZE 2048 #define NO_OF_SDB_ENTRIES ((32*MY_PAGE_SIZE)/SDB_SIZE) /* Offsets to the other Tachyon registers. * (As defined in the Tachyon manual) */ #define TACHYON_CONFIG_REGISTER_OFFSET 0x184 #define TACHYON_CONTROL_REGISTER_OFFSET 0x188 #define TACHYON_STATUS_REGISTER_OFFSET 0x18C #define TACHYON_FLUSH_SEST_REGISTER_OFFSET 0x190 /* Defines for the Tachyon Configuration register. */ #define SCSI_ENABLE 0x40000000 #define WRITE_STREAM_SIZE 0x800 /* size = 16 */ #define READ_STREAM_SIZE 0x300 /* size = 64 */ #define PARITY_EVEN 0x2 #define OOO_REASSEMBLY_DISABLE 0x40 /* Defines for the Tachyon Control register. */ #define SOFTWARE_RESET 0x80000000 #define OCQ_RESET 0x4 #define ERROR_RELEASE 0x2 /* Defines for the Tachyon Status register. */ #define RECEIVE_FIFO_EMPTY 0x10 #define OSM_FROZEN 0x1 #define OCQ_RESET_STATUS 0x20 #define SCSI_FREEZE_STATUS 0x40 /* Offsets to the Frame Manager registers. */ #define FMGR_CONFIG_REGISTER_OFFSET 0x1C0 #define FMGR_CONTROL_REGISTER_OFFSET 0x1C4 #define FMGR_STATUS_REGISTER_OFFSET 0x1C8 #define FMGR_TIMER_REGISTER_OFFSET 0x1CC #define FMGR_WWN_HI_REGISTER_OFFSET 0x1E0 #define FMGR_WWN_LO_REGISTER_OFFSET 0x1E4 #define FMGR_RCVD_ALPA_REGISTER_OFFSET 0x1E8 /* Defines for the Frame Manager Configuration register. */ #define BB_CREDIT 0x10000 #define NPORT 0x8000 #define LOOP_INIT_FABRIC_ADDRESS 0x400 #define LOOP_INIT_PREVIOUS_ADDRESS 0x200 #define LOOP_INIT_SOFT_ADDRESS 0x80 /* Defines for the Frame Manager Control register. */ #define HOST_CONTROL 0x02 #define EXIT_HOST_CONTROL 0x03 #define OFFLINE 0x05 #define INITIALIZE 0x06 #define CLEAR_LF 0x07 /* Defines for the Frame Manager Status register. */ #define LOOP_UP 0x80000000 #define TRANSMIT_PARITY_ERROR 0x40000000 #define NON_PARTICIPATING 0x20000000 #define OUT_OF_SYNC 0x02000000 #define LOSS_OF_SIGNAL 0x01000000 #define NOS_OLS_RECEIVED 0x00080000 #define LOOP_STATE_TIMEOUT 0x00040000 #define LIPF_RECEIVED 0x00020000 #define BAD_ALPA 0x00010000 #define LINK_FAILURE 0x00001000 #define ELASTIC_STORE_ERROR 0x00000400 #define LINK_UP 0x00000200 #define LINK_DOWN 0x00000100 #define ARBITRATING 0x00000010 #define ARB_WON 0x00000020 #define OPEN 0x00000030 #define OPENED 0x00000040 #define TX_CLS 0x00000050 #define RX_CLS 0x00000060 #define TRANSFER 0x00000070 #define INITIALIZING 0x00000080 #define LOOP_FAIL 0x000000D0 #define OLD_PORT 0x000000F0 #define PORT_STATE_ACTIVE 0x0000000F #define PORT_STATE_OFFLINE 0x00000000 #define PORT_STATE_LF1 0x00000009 #define PORT_STATE_LF2 0x0000000A /* Completion Message Types * (defined in P.177 of the Tachyon manual) */ #define OUTBOUND_COMPLETION 0x000 #define OUTBOUND_COMPLETION_I 0x100 #define OUT_HI_PRI_COMPLETION 0x001 #define OUT_HI_PRI_COMPLETION_I 0x101 #define INBOUND_MFS_COMPLETION 0x102 #define INBOUND_OOO_COMPLETION 0x003 #define INBOUND_SFS_COMPLETION 0x104 #define INBOUND_C1_TIMEOUT 0x105 #define INBOUND_UNKNOWN_FRAME_I 0x106 #define INBOUND_BUSIED_FRAME 0x006 #define SFS_BUF_WARN 0x107 #define MFS_BUF_WARN 0x108 #define IMQ_BUF_WARN 0x109 #define FRAME_MGR_INTERRUPT 0x10A #define READ_STATUS 0x10B #define INBOUND_SCSI_DATA_COMPLETION 0x10C #define INBOUND_SCSI_COMMAND 0x10D #define BAD_SCSI_FRAME 0x10E #define INB_SCSI_STATUS_COMPLETION 0x10F /* One of the things that we care about when we receive an * Outbound Completion Message (OCM). */ #define OCM_TIMEOUT_OR_BAD_ALPA 0x0800 /* Defines for the Tachyon Header structure. */ #define SOFI3 0x70 #define SOFN3 0xB0 #define EOFN 0x5 /* R_CTL */ #define FC4_DEVICE_DATA 0 #define EXTENDED_LINK_DATA 0x20000000 #define FC4_LINK_DATA 0x30000000 #define BASIC_LINK_DATA 0x80000000 #define LINK_CONTROL 0xC0000000 #define SOLICITED_DATA 0x1000000 #define UNSOLICITED_CONTROL 0x2000000 #define SOLICITED_CONTROL 0x3000000 #define UNSOLICITED_DATA 0x4000000 #define DATA_DESCRIPTOR 0x5000000 #define UNSOLICITED_COMMAND 0x6000000 #define RCTL_ELS_UCTL 0x22000000 #define RCTL_ELS_SCTL 0x23000000 #define RCTL_BASIC_ABTS 0x81000000 #define RCTL_BASIC_ACC 0x84000000 #define RCTL_BASIC_RJT 0x85000000 /* TYPE */ #define TYPE_BLS 0x00000000 #define TYPE_ELS 0x01000000 #define TYPE_FC_SERVICES 0x20000000 #define TYPE_LLC_SNAP 0x05000000 #define TYPE_FCP 0x08000000 /* F_CTL */ #define EXCHANGE_RESPONDER 0x800000 #define SEQUENCE_RESPONDER 0x400000 #define FIRST_SEQUENCE 0x200000 #define LAST_SEQUENCE 0x100000 #define SEQUENCE_INITIATIVE 0x10000 #define RELATIVE_OFF_PRESENT 0x8 #define END_SEQUENCE 0x80000 #define TACHYON_HEADER_LEN 32 #define NW_HEADER_LEN 16 /* Defines for the Outbound Descriptor Block (ODB). */ #define ODB_CLASS_3 0xC000 #define ODB_NO_COMP 0x400 #define ODB_NO_INT 0x200 #define ODB_EE_CREDIT 0xF /* Defines for the Extended Descriptor Block (EDB). */ #define EDB_LEN ((32*MY_PAGE_SIZE)/8) #define EDB_END 0x8000 #define EDB_FREE 0 #define EDB_BUSY 1 /* Command Codes */ #define ELS_LS_RJT 0x01000000 #define ELS_ACC 0x02000000 #define ELS_PLOGI 0x03000000 #define ELS_FLOGI 0x04000000 #define ELS_LOGO 0x05000000 #define ELS_TPRLO 0x24000000 #define ELS_ADISC 0x52000000 #define ELS_PDISC 0x50000000 #define ELS_PRLI 0x20000000 #define ELS_PRLO 0x21000000 #define ELS_SCR 0x62000000 #define ELS_RSCN 0x61000000 #define ELS_FARP_REQ 0x54000000 #define ELS_ABTX 0x06000000 #define ELS_ADVC 0x0D000000 #define ELS_ECHO 0x10000000 #define ELS_ESTC 0x0C000000 #define ELS_ESTS 0x0B000000 #define ELS_RCS 0x07000000 #define ELS_RES 0x08000000 #define ELS_RLS 0x0F000000 #define ELS_RRQ 0x12000000 #define ELS_RSS 0x09000000 #define ELS_RTV 0x0E000000 #define ELS_RSI 0x0A000000 #define ELS_TEST 0x11000000 #define ELS_RNC 0x53000000 #define ELS_RVCS 0x41000000 #define ELS_TPLS 0x23000000 #define ELS_GAID 0x30000000 #define ELS_FACT 0x31000000 #define ELS_FAN 0x60000000 #define ELS_FDACT 0x32000000 #define ELS_NACT 0x33000000 #define ELS_NDACT 0x34000000 #define ELS_QoSR 0x40000000 #define ELS_FDISC 0x51000000 #define ELS_NS_PLOGI 0x03FFFFFC /* LS_RJT reason codes. */ #define INV_LS_CMND_CODE 0x0001 #define LOGICAL_ERR 0x0003 #define LOGICAL_BUSY 0x0005 #define PROTOCOL_ERR 0x0007 #define UNABLE_TO_PERFORM 0x0009 #define CMND_NOT_SUPP 0x000B /* LS_RJT explanation codes. */ #define NO_EXPLN 0x0000 #define RECV_FIELD_SIZE 0x0700 #define CONC_SEQ 0x0900 #define REQ_NOT_SUPPORTED 0x2C00 #define INV_PAYLOAD_LEN 0x2D00 /* Payload Length defines. */ #define PLOGI_LEN 116 #define CONCURRENT_SEQUENCES 0x01 #define RO_INFO_CATEGORY 0xFE #define E_D_TOV 0x07D0 /* 2 Secs */ #define AL_TIME 0x0010 /* ~15 msec */ #define TOV_VALUES (AL_TIME << 16) | E_D_TOV #define RT_TOV 0x64 /* 100 msec */ #define PTP_TOV_VALUES (RT_TOV << 16) | E_D_TOV #define SERVICE_VALID 0x8000 #define SEQUENCE_DELIVERY 0x0800 #define CLASS3_CONCURRENT_SEQUENCE 0x01 #define CLASS3_OPEN_SEQUENCE 0x01 /* These are retrieved from the NOVRAM. */ #define WORLD_WIDE_NAME_LOW fi->g.my_port_name_low #define WORLD_WIDE_NAME_HIGH fi->g.my_port_name_high #define N_PORT_NAME_HIGH fi->g.my_port_name_high #define N_PORT_NAME_LOW fi->g.my_port_name_low #define NODE_NAME_HIGH fi->g.my_node_name_high #define NODE_NAME_LOW fi->g.my_node_name_low #define PORT_NAME_LEN 8 #define NODE_NAME_LEN 8 #define PH_VERSION 0x0909 #define LOOP_BB_CREDIT 0x00 #define PT2PT_BB_CREDIT 0x01 #define FLOGI_C_F 0x0800 /* Alternate BB_Credit Mgmnt */ #define PLOGI_C_F 0x8800 /* Continuously Increasing + Alternate BB_Credit Management */ /* Fabric defines */ #define DIRECTORY_SERVER 0xFFFFFC #define FABRIC_CONTROLLER 0xFFFFFD #define F_PORT 0xFFFFFE #define FLOGI_DID 0xFFFE #define NS_PLOGI_DID 0xFFFC /* Fibre Channel Services defines */ #define FCS_RFC_4 0x02170000 #define FCS_GP_ID4 0x01A10000 #define FCS_ACC 0x8002 #define FCS_REJECT 0x8001 /* CT Header defines */ #define FC_CT_REV 0x01000000 #define DIRECTORY_SERVER_APP 0xFC #define NAME_SERVICE 0x02 /* Port Type defines */ #define PORT_TYPE_IP 0x05000000 #define PORT_TYPE_NX_PORTS 0x7F000000 /* SCR defines */ #define FABRIC_DETECTED_REG 0x00000001 #define N_PORT_DETECTED_REG 0x00000002 #define FULL_REGISTRATION 0x00000003 #define CLEAR_REGISTRATION 0x000000FF /* Command structure has only one byte to address targets */ #define MAX_SCSI_TARGETS 0xFF #define FC_SCSI_READ 0x80 #define FC_SCSI_WRITE 0x81 #define FC_ELS 0x01 #define FC_BLS 0x00 #define FC_IP 0x05 #define FC_BROADCAST 0xFF /* SEST defines. */ #define SEST_V 0x80000000 /* V = 1 */ #define INB_SEST_VED 0xA0000000 /* V = 1, D = 1 */ #define SEST_INV 0x7FFFFFFF #define OUTB_SEST_VED 0x80000000 /* V = 1 */ #define INV_SEQ_LEN 0xFFFFFFFF #define OUTB_SEST_LINK 0xFFFF /* PRLI defines. */ #define PAGE_LEN 0x100000 /* 3rd byte - 0x10 */ #define PRLI_LEN 0x0014 /* 20 bytes */ #define FCP_TYPE_CODE 0x0800 /* FCP-SCSI */ #define IMAGE_PAIR 0x2000 /* establish image pair */ #define INITIATOR_FUNC 0x00000020 #define TARGET_FUNC 0x00000010 #define READ_XFER_RDY_DISABLED 0x00000002 #define NODE_PROCESS_LOGGED_IN 0x3 #define NODE_NOT_PRESENT 0x2 #define NODE_LOGGED_IN 0x1 #define NODE_LOGGED_OUT 0x0 /* Defines to determine what should be returned when a SCSI frame * times out. */ #define FC_SCSI_BAD_TARGET 0xFFFE0000 /* RSCN Address formats */ #define PORT_ADDRESS_FORMAT 0x00 #define AREA_ADDRESS_FORMAT 0x01 #define DOMAIN_ADDRESS_FORMAT 0x02 /* Defines used to determine whether a frame transmission should * be indicated by an interrupt or not. */ #define NO_COMP_AND_INT 0 #define INT_AND_COMP_REQ 1 #define NO_INT_COMP_REQ 2 /* Other junk... */ #define SDB_FREE 0 #define SDB_BUSY 1 #define MAX_PENDING_FRAMES 15 #define RX_ID_FIRST_SEQUENCE 0xFFFF #define OX_ID_FIRST_SEQUENCE 0xFFFF #define NOT_SCSI_XID 0x8000 #define MAX_SCSI_XID 0x0FFF /* X_IDs are from 0-4095 */ #define SCSI_READ_BIT 0x4000 #define MAX_SCSI_OXID 0x4FFF #define OXID_AVAILABLE 0 #define OXID_INUSE 1 #define MAX_SEQ_ID 0xFF #define INITIATOR 2 #define TARGET 1 #define DELETE_ENTRY 1 #define ADD_ENTRY 2 #endif /* _TACH_H */