URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [net/] [mace.h] - Rev 1275
Go to most recent revision | Compare with Previous | Blame | View Log
/* * mace.h - definitions for the registers in the Am79C940 MACE * (Medium Access Control for Ethernet) controller. * * Copyright (C) 1996 Paul Mackerras. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ #define REG(x) volatile unsigned char x; char x ## _pad[15] struct mace { REG(rcvfifo); /* receive FIFO */ REG(xmtfifo); /* transmit FIFO */ REG(xmtfc); /* transmit frame control */ REG(xmtfs); /* transmit frame status */ REG(xmtrc); /* transmit retry count */ REG(rcvfc); /* receive frame control */ REG(rcvfs); /* receive frame status (4 bytes) */ REG(fifofc); /* FIFO frame count */ REG(ir); /* interrupt register */ REG(imr); /* interrupt mask register */ REG(pr); /* poll register */ REG(biucc); /* bus interface unit config control */ REG(fifocc); /* FIFO configuration control */ REG(maccc); /* medium access control config control */ REG(plscc); /* phys layer signalling config control */ REG(phycc); /* physical configuration control */ REG(chipid_lo); /* chip ID, lsb */ REG(chipid_hi); /* chip ID, msb */ REG(iac); /* internal address config */ REG(reg19); REG(ladrf); /* logical address filter (8 bytes) */ REG(padr); /* physical address (6 bytes) */ REG(reg22); REG(reg23); REG(mpc); /* missed packet count (clears when read) */ REG(reg25); REG(rntpc); /* runt packet count (clears when read) */ REG(rcvcc); /* recv collision count (clears when read) */ REG(reg28); REG(utr); /* user test reg */ REG(reg30); REG(reg31); }; /* Bits in XMTFC */ #define DRTRY 0x80 /* don't retry transmission after collision */ #define DXMTFCS 0x08 /* don't append FCS to transmitted frame */ #define AUTO_PAD_XMIT 0x01 /* auto-pad short packets on transmission */ /* Bits in XMTFS: only valid when XMTSV is set in PR and XMTFS */ #define XMTSV 0x80 /* transmit status (i.e. XMTFS) valid */ #define UFLO 0x40 /* underflow - xmit fifo ran dry */ #define LCOL 0x20 /* late collision (transmission aborted) */ #define MORE 0x10 /* 2 or more retries needed to xmit frame */ #define ONE 0x08 /* 1 retry needed to xmit frame */ #define DEFER 0x04 /* MACE had to defer xmission (enet busy) */ #define LCAR 0x02 /* loss of carrier (transmission aborted) */ #define RTRY 0x01 /* too many retries (transmission aborted) */ /* Bits in XMTRC: only valid when XMTSV is set in PR (and XMTFS) */ #define EXDEF 0x80 /* had to defer for excessive time */ #define RETRY_MASK 0x0f /* number of retries (0 - 15) */ /* Bits in RCVFC */ #define LLRCV 0x08 /* low latency receive: early DMA request */ #define M_RBAR 0x04 /* sets function of EAM/R pin */ #define AUTO_STRIP_RCV 0x01 /* auto-strip short LLC frames on recv */ /* * Bits in RCVFS. After a frame is received, four bytes of status * are automatically read from this register and appended to the frame * data in memory. These are: * Byte 0 and 1: message byte count and frame status * Byte 2: runt packet count * Byte 3: receive collision count */ #define RS_OFLO 0x8000 /* receive FIFO overflowed */ #define RS_CLSN 0x4000 /* received frame suffered (late) collision */ #define RS_FRAMERR 0x2000 /* framing error flag */ #define RS_FCSERR 0x1000 /* frame had FCS error */ #define RS_COUNT 0x0fff /* mask for byte count field */ /* Bits (fields) in FIFOFC */ #define RCVFC_SH 4 /* receive frame count in FIFO */ #define RCVFC_MASK 0x0f #define XMTFC_SH 0 /* transmit frame count in FIFO */ #define XMTFC_MASK 0x0f /* * Bits in IR and IMR. The IR clears itself when read. * Setting a bit in the IMR will disable the corresponding interrupt. */ #define JABBER 0x80 /* jabber error - 10baseT xmission too long */ #define BABBLE 0x40 /* babble - xmitter xmitting for too long */ #define CERR 0x20 /* collision err - no SQE test (heartbeat) */ #define RCVCCO 0x10 /* RCVCC overflow */ #define RNTPCO 0x08 /* RNTPC overflow */ #define MPCO 0x04 /* MPC overflow */ #define RCVINT 0x02 /* receive interrupt */ #define XMTINT 0x01 /* transmitter interrupt */ /* Bits in PR */ #define XMTSV 0x80 /* XMTFS valid (same as in XMTFS) */ #define TDTREQ 0x40 /* set when xmit fifo is requesting data */ #define RDTREQ 0x20 /* set when recv fifo requests data xfer */ /* Bits in BIUCC */ #define BSWP 0x40 /* byte swap, i.e. big-endian bus */ #define XMTSP_4 0x00 /* start xmitting when 4 bytes in FIFO */ #define XMTSP_16 0x10 /* start xmitting when 16 bytes in FIFO */ #define XMTSP_64 0x20 /* start xmitting when 64 bytes in FIFO */ #define XMTSP_112 0x30 /* start xmitting when 112 bytes in FIFO */ #define SWRST 0x01 /* software reset */ /* Bits in FIFOCC */ #define XMTFW_8 0x00 /* xmit fifo watermark = 8 words free */ #define XMTFW_16 0x40 /* 16 words free */ #define XMTFW_32 0x80 /* 32 words free */ #define RCVFW_16 0x00 /* recv fifo watermark = 16 bytes avail */ #define RCVFW_32 0x10 /* 32 bytes avail */ #define RCVFW_64 0x20 /* 64 bytes avail */ #define XMTFWU 0x08 /* xmit fifo watermark update enable */ #define RCVFWU 0x04 /* recv fifo watermark update enable */ #define XMTBRST 0x02 /* enable transmit burst mode */ #define RCVBRST 0x01 /* enable receive burst mode */ /* Bits in MACCC */ #define PROM 0x80 /* promiscuous mode */ #define DXMT2PD 0x40 /* disable xmit two-part deferral algorithm */ #define EMBA 0x20 /* enable modified backoff algorithm */ #define DRCVPA 0x08 /* disable receiving physical address */ #define DRCVBC 0x04 /* disable receiving broadcasts */ #define ENXMT 0x02 /* enable transmitter */ #define ENRCV 0x01 /* enable receiver */ /* Bits in PLSCC */ #define XMTSEL 0x08 /* select DO+/DO- state when idle */ #define PORTSEL_AUI 0x00 /* select AUI port */ #define PORTSEL_10T 0x02 /* select 10Base-T port */ #define PORTSEL_DAI 0x04 /* select DAI port */ #define PORTSEL_GPSI 0x06 /* select GPSI port */ #define ENPLSIO 0x01 /* enable optional PLS I/O pins */ /* Bits in PHYCC */ #define LNKFL 0x80 /* reports 10Base-T link failure */ #define DLNKTST 0x40 /* disable 10Base-T link test */ #define REVPOL 0x20 /* 10Base-T receiver polarity reversed */ #define DAPC 0x10 /* disable auto receiver polarity correction */ #define LRT 0x08 /* low receive threshold for long links */ #define ASEL 0x04 /* auto-select AUI or 10Base-T port */ #define RWAKE 0x02 /* remote wake function */ #define AWAKE 0x01 /* auto wake function */ /* Bits in IAC */ #define ADDRCHG 0x80 /* request address change */ #define PHYADDR 0x04 /* access physical address */ #define LOGADDR 0x02 /* access multicast filter */ /* Bits in UTR */ #define RTRE 0x80 /* reserved test register enable. DON'T SET. */ #define RTRD 0x40 /* reserved test register disable. Sticky */ #define RPAC 0x20 /* accept runt packets */ #define FCOLL 0x10 /* force collision */ #define RCVFCSE 0x08 /* receive FCS enable */ #define LOOP_NONE 0x00 /* no loopback */ #define LOOP_EXT 0x02 /* external loopback */ #define LOOP_INT 0x04 /* internal loopback, excludes MENDEC */ #define LOOP_MENDEC 0x06 /* internal loopback, includes MENDEC */
Go to most recent revision | Compare with Previous | Blame | View Log