URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [scsi/] [sim710.c] - Rev 1774
Go to most recent revision | Compare with Previous | Blame | View Log
/* * sim710.c - Copyright (C) 1999 Richard Hirst <richard@sleepie.demon.co.uk> * *---------------------------------------------------------------------------- * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. *---------------------------------------------------------------------------- * * MCA card detection code by Trent McNair. * Fixes to not explicitly nul bss data from Xavier Bestel. * Some multiboard fixes from Rolf Eike Beer. * Auto probing of EISA config space from Trevor Hemsley. * * Various bits of code in this driver have been copied from 53c7,8xx,c, * which is coyright Drew Eckhardt. The scripts for the SCSI chip are * compiled with the script compiler written by Drew. * * This is a simple driver for the NCR53c710. More complex drivers * for this chip (e.g. 53c7xx.c) require that the scsi chip be able to * do DMA block moves between memory and on-chip registers, which can * be a problem if those registers are in the I/O address space. There * can also be problems on hardware where the registers are memory * mapped, if the design is such that memory-to-memory transfers initiated * by the scsi chip cannot access the chip registers. * * This driver is designed to avoid these problems and is intended to * work with any Intel machines using 53c710 chips, including various * Compaq and NCR machines. It was initially written for the Tadpole * TP34V VME board which is 68030 based. * * The driver supports boot-time parameters similar to * sim710=addr:0x9000,irq:15 * and insmod parameters similar to * sim710="addr:0x9000 irq:15" * * Multiple controllers can also be set up by command line, provided the * addr: parameter is specified first for each controller. e.g. * sim710="addr:0x9000 irq:15 addr:0x8000 irq:14" * * To seperate the different options, ' ', '+', and ',' can be used, except * that ',' can not be used in module parameters. ' ' can be a pain, because * it needs to be quoted, which causes problems with some installers. * The command line above is completely equivalent to * sim710="addr:0x9000+irq:15+addr:0x8000+irq:14" * * The complete list of options are: * * addr:0x9000 Specifies the base I/O port (or address) of the 53C710. * irq:15 Specifies the IRQ number used by the 53c710. * debug:0xffff Generates lots of debug output. * ignore:0x0a Makes the driver ignore SCSI IDs 0 and 2. * nodisc:0x70 Prevents disconnects from IDs 6, 5 and 4. * noneg:0x10 Prevents SDTR negotiation on ID 4. * disabled:1 Completely disables the driver. When present, overrides * all other options. * * The driver will auto-probe chip addresses and IRQs now, so typically no * parameters are needed. Auto-probing of addresses is disabled if any addr: * parameters are specified. * * Current limitations: * * o Async only * o Severely lacking in error recovery * o 'debug:' should be per host really. * */ #include <linux/config.h> #include <linux/module.h> #include <linux/version.h> #include <linux/kernel.h> #include <linux/types.h> #include <linux/string.h> #include <linux/ioport.h> #include <linux/delay.h> #include <linux/sched.h> #include <linux/proc_fs.h> #include <linux/init.h> #include <linux/mca.h> #include <linux/interrupt.h> #include <asm/dma.h> #include <asm/system.h> #include <linux/spinlock.h> #include <asm/io.h> #include <asm/pgtable.h> #include <asm/byteorder.h> #include <linux/blk.h> /* All targets are I/O mapped at the moment */ #define IO_MAPPED #if defined(CONFIG_MCA) /* * For each known microchannel card using the 53c710 we need a list * of possible IRQ and IO settings, as well as their corresponding * bit assignment in pos[]. This might get cumbersome if there * are more than a few cards (I only know of 2 at this point). */ #define MCA_53C710_IDS { 0x01bb, 0x01ba, 0x004f } /* CARD ID 01BB and 01BA use the same pos values */ #define MCA_01BB_IO_PORTS { 0x0000, 0x0000, 0x0800, 0x0C00, 0x1000, 0x1400, \ 0x1800, 0x1C00, 0x2000, 0x2400, 0x2800, \ 0x2C00, 0x3000, 0x3400, 0x3800, 0x3C00, \ 0x4000, 0x4400, 0x4800, 0x4C00, 0x5000 } #define MCA_01BB_IRQS { 3, 5, 11, 14 } /* CARD ID 004f */ #define MCA_004F_IO_PORTS { 0x0000, 0x0200, 0x0300, 0x0400, 0x0500, 0x0600 } #define MCA_004F_IRQS { 5, 9, 14 } #endif #include "scsi.h" #include "hosts.h" #include "sim710.h" #include<linux/stat.h> #define DEBUG #undef DEBUG_LIMIT_INTS /* Define to 10 to hang driver after 10 ints */ /* Debug options available via the "debug:0x1234" parameter */ #define DEB_NONE 0x0000 /* Nothing */ #define DEB_HALT 0x0001 /* Detailed trace of chip halt funtion */ #define DEB_REGS 0x0002 /* All chip register read/writes */ #define DEB_SYNC 0x0004 /* Sync/async negotiation */ #define DEB_PMM 0x0008 /* Phase mis-match handling */ #define DEB_INTS 0x0010 /* General interrupt trace */ #define DEB_TOUT 0x0020 /* Selection timeouts */ #define DEB_RESUME 0x0040 /* Resume addresses for the script */ #define DEB_CMND 0x0080 /* Commands and status returned */ #define DEB_FIXUP 0x0100 /* Fixup of scsi addresses */ #define DEB_DISC 0x0200 /* Disconnect/reselect handling */ #define DEB_ANY 0xffff /* Any and all debug options */ #ifdef DEBUG #define DEB(m,x) if (sim710_debug & m) x int sim710_debug; #else #define DEB(m,x) #endif /* Redefine scsi_done to force renegotiation of (a)sync transfers * following any failed command. */ #define SCSI_DONE(cmd) { \ DEB(DEB_CMND, printk("scsi%d: Complete %08x\n", \ host->host_no, cmd->result)); \ if (cmd->result) \ hostdata->negotiate |= (1 << cmd->target); \ cmd->scsi_done(cmd); \ } #ifndef offsetof #define offsetof(t, m) ((size_t) (&((t *)0)->m)) #endif #define STATE_INITIALISED 0 #define STATE_HALTED 1 #define STATE_IDLE 2 #define STATE_BUSY 3 #define STATE_DISABLED 4 #define MAXBOARDS 4 /* Increase this and the sizes of the arrays below, if you need more.. */ #ifdef MODULE char *sim710; /* command line passed by insmod */ MODULE_AUTHOR("Richard Hirst"); MODULE_DESCRIPTION("Simple NCR53C710 driver"); MODULE_LICENSE("GPL"); MODULE_PARM(sim710, "s"); #endif static int sim710_errors; /* Count of error interrupts */ static int sim710_intrs; /* Count of all interrupts */ static int ignore_ids[MAXBOARDS]; /* Accept all SCSI IDs */ static int opt_nodisc[MAXBOARDS]; /* Allow disconnect on all IDs */ static int opt_noneg[MAXBOARDS]; /* Allow SDTR negotiation on all IDs */ static int hostdata_order; /* Encoded size of hostdata for free_pages() */ static int no_of_boards; /* Actual number of boards/chips */ static unsigned int bases[MAXBOARDS]; /* Base addresses of chips */ static unsigned int irq_vectors[MAXBOARDS]; /* IRQ vectors used by chips */ /* The SCSI Script!!! */ #include "sim710_d.h" /* Now define offsets in the DSA, as (A_dsa_xxx/4) */ #define DSA_SELECT (A_dsa_select/4) #define DSA_MSGOUT (A_dsa_msgout/4) #define DSA_CMND (A_dsa_cmnd/4) #define DSA_STATUS (A_dsa_status/4) #define DSA_MSGIN (A_dsa_msgin/4) #define DSA_DATAIN (A_dsa_datain/4) #define DSA_DATAOUT (A_dsa_dataout/4) #define DSA_SIZE (A_dsa_size/4) #define MAX_SG 128 /* Scatter/Gather elements */ #define MAX_MSGOUT 8 #define MAX_MSGIN 8 #define MAX_CMND 12 #define MAX_STATUS 1 struct sim710_hostdata{ int state; Scsi_Cmnd * issue_queue; Scsi_Cmnd * running; int chip; u8 negotiate; u8 reselected_identify; u8 msgin_buf[MAX_MSGIN]; u8 msg_reject; u32 test1_src __attribute__ ((aligned (4))); u32 test1_dst; struct sim710_target { Scsi_Cmnd *cur_cmd; u32 resume_offset; u32 data_in_jump; u32 data_out_jump; u32 dsa[DSA_SIZE]; /* SCSI Script DSA area */ u8 dsa_msgout[MAX_MSGOUT]; u8 dsa_msgin[MAX_MSGIN]; u8 dsa_cdb[MAX_CMND]; u8 dsa_status[MAX_STATUS]; } target[8]; u32 script[sizeof(SCRIPT)/4] __attribute__ ((aligned (4))); }; /* Template to request asynchronous transfers */ static const unsigned char async_message[] = { EXTENDED_MESSAGE, 3 /* length */, EXTENDED_SDTR, 0, 0 /* asynchronous */}; static void sim710_intr_handle(int irq, void *dev_id, struct pt_regs *regs); static void do_sim710_intr_handle(int irq, void *dev_id, struct pt_regs *regs); static __inline__ void run_process_issue_queue(struct sim710_hostdata *); static void process_issue_queue (struct sim710_hostdata *, unsigned long flags); static int full_reset(struct Scsi_Host * host); /* * Function : static void ncr_dump (struct Scsi_Host *host) * * Purpose : Dump (possibly) useful info * * Inputs : host - pointer to this host adapter's structure */ static void ncr_dump (struct Scsi_Host *host) { unsigned long flags; struct sim710_hostdata *hostdata = (struct sim710_hostdata *) host->hostdata[0]; save_flags(flags); cli(); printk("scsi%d: Chip register contents:\n", host->host_no); printk(" (script at virt %p, bus %lx)\n", hostdata->script, virt_to_bus(hostdata->script)); printk(" 00 sien: %02x sdid: %02x scntl1:%02x scntl0:%02x\n" " 04 socl: %02x sodl: %02x sxfer: %02x scid: %02x\n" " 08 sbcl: %02x sbdl: %02x sidl: %02x sfbr: %02x\n" " 0C sstat2:%02x sstat1:%02x sstat0:%02x dstat: %02x\n" " 10 dsa: %08x\n" " 14 ctest3:%02x ctest2:%02x ctest1:%02x ctest0:%02x\n" " 18 ctest7:%02x ctest6:%02x ctest5:%02x ctest4:%02x\n" " 1C temp: %08x\n" " 20 lcrc: %02x ctest8:%02x istat: %02x dfifo: %02x\n" " 24 dbc: %08x dnad: %08x dsp: %08x\n" " 30 dsps: %08x scratch:%08x\n" " 38 dcntl: %02x dwt: %02x dien: %02x dmode: %02x\n" " 3C adder: %08x\n", NCR_read8(SIEN_REG), NCR_read8(SDID_REG), NCR_read8(SCNTL1_REG), NCR_read8(SCNTL0_REG), NCR_read8(SOCL_REG), NCR_read8(SODL_REG), NCR_read8(SXFER_REG), NCR_read8(SCID_REG), NCR_read8(SBCL_REG), NCR_read8(SBDL_REG), NCR_read8(SIDL_REG), NCR_read8(SFBR_REG), NCR_read8(SSTAT2_REG), NCR_read8(SSTAT1_REG), NCR_read8(SSTAT0_REG), NCR_read8(DSTAT_REG), NCR_read32(DSA_REG), NCR_read8(CTEST3_REG), NCR_read8(CTEST2_REG), NCR_read8(CTEST1_REG), NCR_read8(CTEST0_REG), NCR_read8(CTEST7_REG), NCR_read8(CTEST6_REG), NCR_read8(CTEST5_REG), NCR_read8(CTEST4_REG), NCR_read8(TEMP_REG), NCR_read8(LCRC_REG), NCR_read8(CTEST8_REG), NCR_read8(ISTAT_REG), NCR_read8(DFIFO_REG), NCR_read32(DBC_REG), NCR_read32(DNAD_REG), NCR_read32(DSP_REG), NCR_read32(DSPS_REG), NCR_read32(SCRATCH_REG), NCR_read8(DCNTL_REG), NCR_read8(DWT_REG), NCR_read8(DIEN_REG), NCR_read8(DMODE_REG), NCR_read32(ADDER_REG)); restore_flags(flags); } /* * Function: int param_setup(char *str) */ __init int param_setup(char *str) { char *cur = str; char *p, *pc, *pv; int val; int c; no_of_boards = 0; while (no_of_boards < MAXBOARDS && cur != NULL && (pc = strchr(cur, ':')) != NULL) { char *pe; val = 0; pv = pc; c = *++pv; val = (int) simple_strtoul(pv, &pe, 0); if (!strncmp(cur, "addr:", 5)) { bases[no_of_boards++] = val; } #ifdef DEBUG else if (!strncmp(cur, "debug:", 6)) { sim710_debug = val; } #endif else if (no_of_boards == 0) { printk("sim710: Invalid parameters, addr: must come first\n"); no_of_boards = -1; return 1; } else if (!strncmp(cur, "irq:", 4)) irq_vectors[no_of_boards-1] = val; else if (!strncmp(cur, "ignore:", 7)) ignore_ids[no_of_boards-1] = val; else if (!strncmp(cur, "nodisc:", 7)) opt_nodisc[no_of_boards-1] = val; else if (!strncmp(cur, "noneg:", 6)) opt_noneg[no_of_boards-1] = val; else if (!strncmp(cur, "disabled:", 9)) { no_of_boards = -1; return 1; } else { printk("sim710: unexpected boot option '%.*s'\n", (int)(pc-cur+1), cur); no_of_boards = -1; return 1; } /* Allow ',', ' ', or '+' seperators. Used to be ',' at boot and * ' ' for module load, some installers crap out on the space and * insmod doesn't like the comma. */ if ((p = strchr(cur, ',')) || (p = strchr(cur, ' ')) || (p = strchr(cur, '+'))) cur = p + 1; else break; } return 1; } #ifndef MODULE __setup("sim710=", param_setup); #endif /* * Function: static const char *sbcl_to_phase (int sbcl) */ static const char * sbcl_to_phase (int sbcl) { switch (sbcl & SBCL_PHASE_MASK) { case SBCL_PHASE_DATAIN: return "DATAIN"; case SBCL_PHASE_DATAOUT: return "DATAOUT"; case SBCL_PHASE_MSGIN: return "MSGIN"; case SBCL_PHASE_MSGOUT: return "MSGOUT"; case SBCL_PHASE_CMDOUT: return "CMDOUT"; case SBCL_PHASE_STATIN: return "STATUSIN"; default: return "unknown"; } } /* * Function : static int ncr_halt (struct Scsi_Host *host) * * Purpose : halts the SCSI SCRIPTS(tm) processor on the NCR chip * * Inputs : host - SCSI chip to halt * * Returns : 0 on success */ static int ncr_halt (struct Scsi_Host *host) { unsigned long flags; unsigned char istat, tmp; struct sim710_hostdata *hostdata = (struct sim710_hostdata *) host->hostdata[0]; int stage; int timeout; int res = 0; save_flags(flags); cli(); /* Stage 0 : eat all interrupts Stage 1 : set ABORT Stage 2 : eat all but abort interrupts Stage 3 : eat all interrupts We loop for 50000 times with a delay of 10us which should give us about half a second. */ for (stage = 0, timeout = 50000; timeout; timeout--) { if (stage == 1) { DEB(DEB_HALT, printk("ncr_halt: writing ISTAT_ABRT\n")); NCR_write8(ISTAT_REG, ISTAT_ABRT); ++stage; } istat = NCR_read8 (ISTAT_REG); if (istat & ISTAT_SIP) { DEB(DEB_HALT, printk("ncr_halt: got ISTAT_SIP, istat=%02x\n", istat)); tmp = NCR_read8(SSTAT0_REG); DEB(DEB_HALT, printk("ncr_halt: got SSTAT0_REG=%02x\n", tmp)); } else if (istat & ISTAT_DIP) { DEB(DEB_HALT, printk("ncr_halt: got ISTAT_DIP, istat=%02x\n", istat)); tmp = NCR_read8(DSTAT_REG); DEB(DEB_HALT, printk("ncr_halt: got DSTAT_REG=%02x\n", tmp)); if (stage == 2) { if (tmp & DSTAT_ABRT) { DEB(DEB_HALT, printk("ncr_halt: got DSTAT_ABRT, clearing istat\n")); NCR_write8(ISTAT_REG, 0); ++stage; } else { res = 1; break; } } } if (!(istat & (ISTAT_SIP|ISTAT_DIP))) { if (stage == 0) ++stage; else if (stage == 3) break; } udelay(10); } restore_flags(flags); if (timeout == 0 || res) { printk(KERN_ALERT "scsi%d: could not halt NCR chip\n", host->host_no); return 1; } else { hostdata->state = STATE_HALTED; return 0; } } /* * Function : static void sim710_soft_reset (struct Scsi_Host *host) * * Purpose : perform a soft reset of the NCR53c7xx chip * * Inputs : host - pointer to this host adapter's structure * * Preconditions : sim710_init must have been called for this * host. * */ static void sim710_soft_reset (struct Scsi_Host *host) { unsigned long flags; save_flags(flags); cli(); /* * Do a soft reset of the chip so that everything is * reinitialized to the power-on state. * * Basically follow the procedure outlined in the NCR53c700 * data manual under Chapter Six, How to Use, Steps Necessary to * Start SCRIPTS, with the exception of actually starting the * script and setting up the synchronous transfer gunk. */ /* XXX Should we reset the scsi bus here? */ NCR_write8(SCNTL1_REG, SCNTL1_RST); /* Reset the bus */ udelay(50); NCR_write8(SCNTL1_REG, 0); udelay(500); NCR_write8(ISTAT_REG, ISTAT_10_SRST); /* Reset the chip */ udelay(50); NCR_write8(ISTAT_REG, 0); mdelay(1000); /* Let devices recover */ NCR_write32(SCRATCH_REG, 0); NCR_write8(DCNTL_REG, DCNTL_10_COM | DCNTL_700_CF_3); NCR_write8(CTEST7_REG, CTEST7_10_CDIS|CTEST7_STD); NCR_write8(DMODE_REG, DMODE_10_BL_8 | DMODE_10_FC2); NCR_write8(SCID_REG, 1 << host->this_id); NCR_write8(SBCL_REG, 0); NCR_write8(SXFER_REG, 0); NCR_write8(SCNTL1_REG, SCNTL1_ESR_700); NCR_write8(SCNTL0_REG, SCNTL0_EPC | SCNTL0_EPG_700 | SCNTL0_ARB1 | SCNTL0_ARB2); NCR_write8(DIEN_REG, DIEN_700_BF | DIEN_ABRT | DIEN_SSI | DIEN_SIR | DIEN_700_OPC); NCR_write8(SIEN_REG_700, SIEN_PAR | SIEN_700_STO | SIEN_RST | SIEN_UDC | SIEN_SGE | SIEN_MA); restore_flags(flags); } /* * Function : static void sim710_driver_init (struct Scsi_Host *host) * * Purpose : Initialize internal structures, as required on startup, or * after a SCSI bus reset. * * Inputs : host - pointer to this host adapter's structure */ static void sim710_driver_init (struct Scsi_Host *host) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *) host->hostdata[0]; int i; hostdata->running = NULL; memcpy (hostdata->script, SCRIPT, sizeof(SCRIPT)); for (i = 0; i < PATCHES; i++) hostdata->script[LABELPATCHES[i]] += virt_to_bus(hostdata->script); patch_abs_32 (hostdata->script, 0, reselected_identify, virt_to_bus((void *)&(hostdata->reselected_identify))); patch_abs_32 (hostdata->script, 0, msgin_buf, virt_to_bus((void *)&(hostdata->msgin_buf[0]))); patch_abs_32 (hostdata->script, 0, msg_reject, virt_to_bus((void *)&(hostdata->msg_reject))); patch_abs_32 (hostdata->script, 0, test1_src, virt_to_bus((void *)&(hostdata->test1_src))); patch_abs_32 (hostdata->script, 0, test1_dst, virt_to_bus((void *)&(hostdata->test1_dst))); hostdata->state = STATE_INITIALISED; hostdata->negotiate = 0xff; } /* Handle incoming Synchronous data transfer request. If our negotiate * flag is set then this is a response to our request, otherwise it is * spurious request from the target. Don't really expect target initiated * SDTRs, because we always negotiate on the first command. Could still * get them though.. * The chip is currently paused with ACK asserted on the last byte of the * SDTR. * resa is the resume address if the message is in response to our outgoing * SDTR. Only possible on initial identify. * resb is the resume address if the message exchange is initiated by the * target. */ static u32 handle_sdtr (struct Scsi_Host * host, Scsi_Cmnd * cmd, u32 resa, u32 resb) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; struct sim710_target *targdata = hostdata->target + cmd->target; u32 resume_offset; if (resa && hostdata->negotiate & (1 << cmd->target)) { DEB(DEB_SYNC, printk("scsi%d: Response to host SDTR = %02x %02x\n", host->host_no, hostdata->msgin_buf[3], hostdata->msgin_buf[4])); /* We always issue an SDTR with the identify, so we must issue * the CDB next. */ resume_offset = resa; hostdata->negotiate &= ~(1 << cmd->target); } else { DEB(DEB_SYNC, printk("scsi%d: Target initiated SDTR = %02x %02x\n", host->host_no, hostdata->msgin_buf[3], hostdata->msgin_buf[4])); memcpy(targdata->dsa_msgout, async_message, sizeof(async_message)); targdata->dsa[DSA_MSGOUT] = sizeof(async_message); /* I guess the target could do this anytime; we have to send our * response, and then continue (sending the CDB if not already done). */ resume_offset = resb; } return resume_offset; } /* * Function : static int datapath_residual (Scsi_Host *host) * * Purpose : return residual data count of what's in the chip. * * Inputs : host - SCSI host */ static int datapath_residual (struct Scsi_Host *host) { int count, synchronous, sstat; unsigned int ddir; count = ((NCR_read8 (DFIFO_REG) & DFIFO_10_BO_MASK) - (NCR_read32 (DBC_REG) & DFIFO_10_BO_MASK)) & DFIFO_10_BO_MASK; synchronous = NCR_read8 (SXFER_REG) & SXFER_MO_MASK; ddir = NCR_read8 (CTEST0_REG_700) & CTEST0_700_DDIR; if (ddir) { /* Receive */ if (synchronous) count += (NCR_read8 (SSTAT2_REG) & SSTAT2_FF_MASK) >> SSTAT2_FF_SHIFT; else if (NCR_read8 (SSTAT1_REG) & SSTAT1_ILF) ++count; } else { /* Send */ sstat = NCR_read8 (SSTAT1_REG); if (sstat & SSTAT1_OLF) ++count; if (synchronous && (sstat & SSTAT1_ORF)) ++count; } return count; } static u32 handle_idd (struct Scsi_Host * host, Scsi_Cmnd * cmd) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; struct sim710_target *targdata = hostdata->target + cmd->target; u32 resume_offset = 0, index; index = (u32)((u32 *)(bus_to_virt(NCR_read32(DSP_REG))) - hostdata->script); switch (index) { case Ent_wait_disc_complete/4 + 2: cmd->result = targdata->dsa_status[0]; SCSI_DONE(cmd); targdata->cur_cmd = NULL; resume_offset = Ent_reselect; break; case Ent_wait_disc2/4 + 2: /* Disconnect after command - just wait for a reselect */ targdata->resume_offset = Ent_resume_msgin2a; resume_offset = Ent_reselect; break; case Ent_wait_disc3/4 + 2: /* Disconnect after the data phase */ targdata->resume_offset = Ent_resume_msgin3a; resume_offset = Ent_reselect; break; case Ent_wait_disc1/4 + 2: /* Disconnect before command - not expected */ targdata->resume_offset = Ent_resume_msgin1a; resume_offset = Ent_reselect; break; default: printk("scsi%d: Unexpected Illegal Instruction, script[%04x]\n", host->host_no, index); sim710_errors++; /* resume_offset is zero, which will cause host reset */ } return resume_offset; } /* Handle a phase mismatch. */ static u32 handle_phase_mismatch (struct Scsi_Host * host, Scsi_Cmnd * cmd) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; struct sim710_target *targdata = hostdata->target + cmd->target; u32 resume_offset = 0, index; unsigned char sbcl; sbcl = NCR_read8(SBCL_REG) & SBCL_PHASE_MASK; index = (u32)((u32 *)(bus_to_virt(NCR_read32(DSP_REG))) - hostdata->script); DEB(DEB_PMM, printk("scsi%d: Phase mismatch, phase %s (%x) at script[0x%x]\n", host->host_no, sbcl_to_phase(sbcl), sbcl, index)); DEB(DEB_PMM, print_command(cmd->cmnd)); if (index == Ent_done_ident/4) { /* Sending initial message out - probably rejecting our sync * negotiation request. */ NCR_write8(SOCL_REG, 0); /* Negate ATN */ if (sbcl == SBCL_PHASE_MSGIN) resume_offset = Ent_resume_rej_ident; else if (sbcl == SBCL_PHASE_CMDOUT) { /* Some old devices (SQ555) switch to cmdout after the first * byte of an identify message, regardless of whether we * have more bytes to send! */ printk("scsi%d: Unexpected switch to CMDOUT during IDENTIFY\n", host->host_no); resume_offset = Ent_resume_cmd; } else if (sbcl == SBCL_PHASE_STATIN) { /* Some devices do this on parity error, at least */ printk("scsi%d: Unexpected switch to STATUSIN on initial message out\n", host->host_no); resume_offset = Ent_end_data_trans; } else { printk("scsi%d: Unexpected phase change to %s on initial msgout\n", host->host_no, sbcl_to_phase(sbcl)); /* resume_offset is zero, which will cause a host reset */ } hostdata->negotiate &= ~(1 << cmd->target); } else if (index > Ent_patch_input_data/4 && index < Ent_patch_output_data/4) { /* DataIn transfer phase */ u32 sg_id, oaddr, olen, naddr, nlen; int residual; sg_id = (index - Ent_patch_input_data/4 - 4) / 2; targdata->data_in_jump = hostdata->script[Ent_patch_input_data/4+1] = virt_to_bus(hostdata->script + Ent_patch_input_data/4 + sg_id * 2 + 2); olen = targdata->dsa[DSA_DATAIN + sg_id * 2]; oaddr = targdata->dsa[DSA_DATAIN + sg_id * 2 + 1]; residual = datapath_residual (host); if (residual) printk("scsi%d: Residual count %d on DataIn - NOT expected!!!", host->host_no, residual); naddr = NCR_read32(DNAD_REG) - residual; nlen = (NCR_read32(DBC_REG) & 0x00ffffff) + residual; DEB(DEB_PMM, printk("scsi%d: DIN sg %d, old %08x/%08x, new %08x/%08x (%d)\n", host->host_no, sg_id, oaddr, olen, naddr, nlen, residual)); if (oaddr+olen != naddr+nlen) { printk("scsi%d: PMM DIN counts error: 0x%x + 0x%x != 0x%x + 0x%x", host->host_no, oaddr, olen, naddr, nlen); } else { targdata->dsa[DSA_DATAIN + sg_id * 2] = nlen; targdata->dsa[DSA_DATAIN + sg_id * 2 + 1] = naddr; resume_offset = Ent_resume_pmm; } } else if (index > Ent_patch_output_data/4 && index <= Ent_end_data_trans/4) { /* Dataout transfer phase */ u32 sg_id, oaddr, olen, naddr, nlen; int residual; sg_id = (index - Ent_patch_output_data/4 - 4) / 2; targdata->data_out_jump = hostdata->script[Ent_patch_output_data/4+1] = virt_to_bus(hostdata->script + Ent_patch_output_data/4 + sg_id * 2 + 2); olen = targdata->dsa[DSA_DATAOUT + sg_id * 2]; oaddr = targdata->dsa[DSA_DATAOUT + sg_id * 2 + 1]; residual = datapath_residual (host); naddr = NCR_read32(DNAD_REG) - residual; nlen = (NCR_read32(DBC_REG) & 0x00ffffff) + residual; DEB(DEB_PMM, printk("scsi%d: DOUT sg %d, old %08x/%08x, new %08x/%08x (%d)\n", host->host_no, sg_id, oaddr, olen, naddr, nlen, residual)); if (oaddr+olen != naddr+nlen) { printk("scsi%d: PMM DOUT counts error: 0x%x + 0x%x != 0x%x + 0x%x", host->host_no, oaddr, olen, naddr, nlen); } else { targdata->dsa[DSA_DATAOUT + sg_id * 2] = nlen; targdata->dsa[DSA_DATAOUT + sg_id * 2 + 1] = naddr; resume_offset = Ent_resume_pmm; } } else if (sbcl == SBCL_PHASE_STATIN) { /* Change to Status In at some random point; probably wants to report a * parity error or similar. */ printk("scsi%d: Unexpected phase change to STATUSIN at index 0x%x\n", host->host_no, index); resume_offset = Ent_end_data_trans; } else { printk("scsi%d: Unexpected phase change to %s at index 0x%x\n", host->host_no, sbcl_to_phase(sbcl), index); /* resume_offset is zero, which will cause a host reset */ } /* Flush DMA FIFO */ NCR_write8 (CTEST8_REG, CTEST8_10_CLF); while (NCR_read8 (CTEST8_REG) & CTEST8_10_CLF); return resume_offset; } static u32 handle_script_int(struct Scsi_Host * host, Scsi_Cmnd * cmd) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; struct sim710_target *targdata = hostdata->target + cmd->target; u32 dsps, resume_offset = 0; unsigned char sbcl; dsps = NCR_read32(DSPS_REG); switch (dsps) { case A_int_cmd_complete: cmd->result = targdata->dsa_status[0]; SCSI_DONE(cmd); targdata->cur_cmd = NULL; resume_offset = Ent_reselect; break; case A_int_msg_sdtr1: resume_offset = handle_sdtr(host, cmd, Ent_resume_msgin1a, Ent_resume_msgin1b); break; case A_int_msg_sdtr2: resume_offset = handle_sdtr(host, cmd, 0, Ent_resume_msgin2b); break; case A_int_msg_sdtr3: resume_offset = handle_sdtr(host, cmd, 0, Ent_resume_msgin3b); break; case A_int_disc1: /* Disconnect before command - not expected */ targdata->resume_offset = Ent_resume_msgin1a; resume_offset = Ent_reselect; break; case A_int_disc2: /* Disconnect after command - just wait for a reselect */ targdata->resume_offset = Ent_resume_msgin2a; resume_offset = Ent_reselect; break; case A_int_disc3: /* Disconnect after the data phase */ targdata->resume_offset = Ent_resume_msgin3a; resume_offset = Ent_reselect; break; case A_int_reselected: hostdata->script[Ent_patch_output_data/4+1] = targdata->data_out_jump; hostdata->script[Ent_patch_input_data/4+1] = targdata->data_in_jump; NCR_write32(DSA_REG, virt_to_bus(targdata->dsa)); resume_offset = targdata->resume_offset; break; case A_int_data_bad_phase: sbcl = NCR_read8(SBCL_REG) & SBCL_PHASE_MASK; printk("scsi%d: int_data_bad_phase, phase %s (%x)\n", host->host_no, sbcl_to_phase(sbcl), sbcl); break; case A_int_bad_msg1: case A_int_bad_msg2: case A_int_bad_msg3: case A_int_cmd_bad_phase: case A_int_no_msgout1: case A_int_no_msgout2: case A_int_no_msgout3: case A_int_not_cmd_complete: case A_int_sel_no_ident: case A_int_sel_not_cmd: case A_int_status_not_msgin: case A_int_resel_not_msgin: case A_int_selected: case A_int_not_rej: default: sbcl = NCR_read8(SBCL_REG) & SBCL_PHASE_MASK; printk("scsi%d: Unimplemented script interrupt: %08x, phase %s\n", host->host_no, dsps, sbcl_to_phase(sbcl)); sim710_errors++; /* resume_offset is zero, which will cause a host reset */ } return resume_offset; } /* A quick wrapper for sim710_intr_handle to grab the spin lock */ static void do_sim710_intr_handle(int irq, void *dev_id, struct pt_regs *regs) { unsigned long flags; spin_lock_irqsave(&io_request_lock, flags); sim710_intr_handle(irq, dev_id, regs); spin_unlock_irqrestore(&io_request_lock, flags); } /* A "high" level interrupt handler */ static void sim710_intr_handle(int irq, void *dev_id, struct pt_regs *regs) { struct Scsi_Host * host = (struct Scsi_Host *)dev_id; struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; Scsi_Cmnd * cmd; unsigned char istat, dstat; unsigned char sstat0; u32 scratch, dsps, resume_offset = 0; istat = NCR_read8(ISTAT_REG); if (!(istat & (ISTAT_SIP|ISTAT_DIP))) return; else { sim710_intrs++; dsps = NCR_read32(DSPS_REG); hostdata->state = STATE_HALTED; sstat0 = dstat = 0; scratch = NCR_read32(SCRATCH_REG); if (istat & ISTAT_SIP) { sstat0 = NCR_read8(SSTAT0_REG); } if (istat & ISTAT_DIP) { udelay(10); /* Some comment somewhere about 10cycles * between accesses to sstat0 and dstat ??? */ dstat = NCR_read8(DSTAT_REG); } DEB(DEB_INTS, printk("scsi%d: Int %d, istat %02x, sstat0 %02x " "dstat %02x, dsp [%04x], scratch %02x\n", host->host_no, sim710_intrs, istat, sstat0, dstat, (u32 *)(bus_to_virt(NCR_read32(DSP_REG))) - hostdata->script, scratch)); if (scratch & 0x100) { u8 *p = hostdata->msgin_buf; DEB(DEB_INTS, printk(" msgin_buf: %02x %02x %02x %02x\n", p[0], p[1], p[2], p[3])); } if ((dstat & DSTAT_SIR) && dsps == A_int_reselected) { /* Reselected. Identify the target from LCRC_REG, and * update current command. If we were trying to select * a device, then that command needs to go back on the * issue_queue for later. */ unsigned char lcrc = NCR_read8(LCRC_REG_10); int id = 0; if (!(lcrc & 0x7f)) { printk("scsi%d: Reselected with LCRC = %02x\n", host->host_no, lcrc); cmd = NULL; } else { while (!(lcrc & 1)) { id++; lcrc >>= 1; } DEB(DEB_DISC, printk("scsi%d: Reselected by ID %d\n", host->host_no, id)); if (hostdata->running) { /* Clear SIGP */ (void)NCR_read8(CTEST2_REG_700); DEB(DEB_DISC, printk("scsi%d: Select of %d interrupted " "by reselect from %d (%p)\n", host->host_no, hostdata->running->target, id, hostdata->target[id].cur_cmd)); cmd = hostdata->running; hostdata->target[cmd->target].cur_cmd = NULL; cmd->SCp.ptr = (unsigned char *) hostdata->issue_queue; hostdata->issue_queue = cmd; } cmd = hostdata->running = hostdata->target[id].cur_cmd; } } else cmd = hostdata->running; if (!cmd) { printk("scsi%d: No active command!\n", host->host_no); printk("scsi%d: Int %d, istat %02x, sstat0 %02x " "dstat %02x, dsp [%04x], scratch %02x, dsps %08x\n", host->host_no, sim710_intrs, istat, sstat0, dstat, (u32 *)(bus_to_virt(NCR_read32(DSP_REG))) - hostdata->script, NCR_read32(SCRATCH_REG), dsps); /* resume_offset is zero, which will cause a host reset */ } else if (sstat0 & SSTAT0_700_STO) { DEB(DEB_TOUT, printk("scsi%d: Selection timeout\n", host->host_no)); cmd->result = DID_NO_CONNECT << 16; SCSI_DONE(cmd); hostdata->target[cmd->target].cur_cmd = NULL; resume_offset = Ent_reselect; } else if (sstat0 & (SSTAT0_SGE|SSTAT0_UDC|SSTAT0_RST|SSTAT0_PAR)) { printk("scsi%d: Serious error, sstat0 = %02x\n", host->host_no, sstat0); sim710_errors++; /* resume_offset is zero, which will cause a host reset */ } else if (dstat & (DSTAT_BF|DSTAT_ABRT|DSTAT_SSI|DSTAT_WTD)) { printk("scsi%d: Serious error, dstat = %02x\n", host->host_no, dstat); sim710_errors++; /* resume_offset is zero, which will cause a host reset */ } else if (dstat & DSTAT_SIR) resume_offset = handle_script_int(host, cmd); else if (sstat0 & SSTAT0_MA) resume_offset = handle_phase_mismatch(host, cmd); else if (dstat & DSTAT_IID) { /* This can be due to a quick reselect while doing a WAIT * DISCONNECT. */ resume_offset = handle_idd(host, cmd); } else { sim710_errors++; printk("scsi%d: Spurious interrupt!\n", host->host_no); /* resume_offset is zero, which will cause a host reset */ } } if (resume_offset) { if (resume_offset == Ent_reselect) { hostdata->running = NULL; hostdata->state = STATE_IDLE; } else hostdata->state = STATE_BUSY; DEB(DEB_RESUME, printk("scsi%d: Resuming at script[0x%x]\n", host->host_no, resume_offset/4)); #ifdef DEBUG_LIMIT_INTS if (sim710_intrs < DEBUG_LIMIT_INTS) #endif { NCR_write32(SCRATCH_REG, 0); NCR_write32(DSP_REG, virt_to_bus(hostdata->script+resume_offset/4)); } if (resume_offset == Ent_reselect) run_process_issue_queue(hostdata); } else { printk("scsi%d: Failed to handle interrupt. Failing commands " "and resetting SCSI bus and chip\n", host->host_no); mdelay(1000); /* Give chance to read screen!! */ full_reset(host); } } static void run_command (struct sim710_hostdata *hostdata, Scsi_Cmnd *cmd) { struct Scsi_Host *host = cmd->host; struct sim710_target *targdata = hostdata->target + cmd->target; int i, datain, dataout, sg_start; u32 *dip, *dop, dsa; DEB(DEB_CMND, printk("scsi%d: id%d starting ", host->host_no, cmd->target)); DEB(DEB_CMND, print_command(cmd->cmnd)); switch (cmd->cmnd[0]) { case INQUIRY: case MODE_SENSE: case READ_6: case READ_10: case READ_CAPACITY: case REQUEST_SENSE: case READ_BLOCK_LIMITS: case READ_TOC: datain = 1; dataout = 0; break; case MODE_SELECT: case WRITE_6: case WRITE_10: datain = 0; dataout = 1; break; case TEST_UNIT_READY: case ALLOW_MEDIUM_REMOVAL: case START_STOP: datain = dataout = 0; break; default: datain = dataout = 1; } memcpy(targdata->dsa_cdb, cmd->cmnd, MAX_CMND); targdata->dsa_msgout[0] = IDENTIFY((opt_nodisc[hostdata->chip] & (1<<cmd->target)) ? 0 : 1 ,0); if (hostdata->negotiate & (1 << cmd->target)) { if (opt_noneg[hostdata->chip] & (1 << cmd->target)) { hostdata->negotiate ^= (1 << cmd->target); targdata->dsa[DSA_MSGOUT] = 1; } else { DEB(DEB_SYNC, printk("scsi%d: Negotiating async transfers " "for ID %d\n", host->host_no, cmd->target)); memcpy(targdata->dsa_msgout+1, async_message, sizeof(async_message)); targdata->dsa[DSA_MSGOUT] = sizeof(async_message) + 1; } } else targdata->dsa[DSA_MSGOUT] = 1; targdata->dsa_msgin[0] = 0xff; targdata->dsa_status[0] = 0xff; targdata->dsa[DSA_SELECT] = (1 << cmd->target) << 16; targdata->dsa[DSA_MSGOUT+1] = virt_to_bus(targdata->dsa_msgout); targdata->dsa[DSA_CMND] = cmd->cmd_len; targdata->dsa[DSA_CMND+1] = virt_to_bus(targdata->dsa_cdb); targdata->dsa[DSA_STATUS] = 1; targdata->dsa[DSA_STATUS+1] = virt_to_bus(targdata->dsa_status); targdata->dsa[DSA_MSGIN] = 1; targdata->dsa[DSA_MSGIN+1] = virt_to_bus(targdata->dsa_msgin); sg_start = (MAX_SG - (cmd->use_sg ? cmd->use_sg : 1)) * 2; dip = targdata->dsa + DSA_DATAIN + sg_start; dop = targdata->dsa + DSA_DATAOUT + sg_start; for (i = 0; cmd->use_sg ? (i < cmd->use_sg) : !i; i++) { u32 vbuf = cmd->use_sg ? (u32)(((struct scatterlist *)cmd->buffer)[i].address) : (u32)(cmd->request_buffer); u32 bbuf = virt_to_bus((void *)vbuf); u32 cnt = cmd->use_sg ? ((struct scatterlist *)cmd->buffer)[i].length : cmd->request_bufflen; if (datain) { *dip++ = cnt; *dip++ = bbuf; } if (dataout) { *dop++ = cnt; *dop++ = bbuf; } } targdata->data_out_jump = hostdata->script[Ent_patch_output_data/4+1] = virt_to_bus(hostdata->script + Ent_patch_output_data/4 + sg_start + 2); targdata->data_in_jump = hostdata->script[Ent_patch_input_data/4+1] = virt_to_bus(hostdata->script + Ent_patch_input_data/4 + sg_start + 2); for (i = 0, dsa = virt_to_bus(targdata->dsa); i < 4; i++) { u32 v = hostdata->script[Ent_patch_new_dsa/4 + i * 2]; v &= ~0x0000ff00; v |= (dsa & 0xff) << 8; hostdata->script[Ent_patch_new_dsa/4 + i * 2] = v; dsa >>= 8; } hostdata->running = targdata->cur_cmd = cmd; hostdata->state = STATE_BUSY; NCR_write8(ISTAT_REG, ISTAT_10_SIGP); } static volatile int process_issue_queue_running = 0; static __inline__ void run_process_issue_queue(struct sim710_hostdata *hostdata) { unsigned long flags; save_flags (flags); cli(); if (!process_issue_queue_running) { process_issue_queue_running = 1; process_issue_queue(hostdata, flags); /* * process_issue_queue_running is cleared in process_issue_queue * once it can't do more work, and process_issue_queue exits with * interrupts disabled. */ } restore_flags (flags); } /* * Function : process_issue_queue (hostdata, flags) * * Purpose : Start next command for any idle target. * * NOTE : process_issue_queue exits with interrupts *disabled*, so the * caller must reenable them if it desires. * * NOTE : process_issue_queue should be called from both * sim710_queue_command() and from the interrupt handler * after command completion. */ static void process_issue_queue (struct sim710_hostdata *hostdata, unsigned long flags) { Scsi_Cmnd *tmp, *prev; int done; /* * We run (with interrupts disabled) until we're sure that none of * the host adapters have anything that can be done, at which point * we set process_issue_queue_running to 0 and exit. * * Interrupts are enabled before doing various other internal * instructions, after we've decided that we need to run through * the loop again. * */ do { cli(); /* Freeze request queues */ done = 1; if (hostdata->issue_queue) { if (hostdata->state == STATE_DISABLED) { tmp = (Scsi_Cmnd *) hostdata->issue_queue; hostdata->issue_queue = (Scsi_Cmnd *) tmp->SCp.ptr; tmp->result = (DID_BAD_TARGET << 16); tmp->scsi_done (tmp); done = 0; } else if (hostdata->state == STATE_IDLE) { for (tmp = hostdata->issue_queue, prev = NULL; tmp; prev = tmp, tmp = (Scsi_Cmnd *) tmp->SCp.ptr) { if (hostdata->target[tmp->target].cur_cmd == NULL) { if (prev) prev->SCp.ptr = tmp->SCp.ptr; else hostdata->issue_queue = (Scsi_Cmnd *) tmp->SCp.ptr; tmp->SCp.ptr = NULL; run_command (hostdata, tmp); done = 0; } /* if target/lun is not busy */ } /* scan issue queue for work */ } /* host is idle */ } /* if hostdata->issue_queue */ if (!done) restore_flags (flags); } while (!done); process_issue_queue_running = 0; } int sim710_queuecommand(Scsi_Cmnd * cmd, void (*done)(Scsi_Cmnd *)) { struct Scsi_Host *host = cmd->host; struct sim710_hostdata *hostdata = (struct sim710_hostdata *)host->hostdata[0]; Scsi_Cmnd *tmp; unsigned long flags; if (cmd->lun) { /* Silently ignore luns other than zero! */ cmd->result = (DID_BAD_TARGET << 16); done(cmd); return 0; } DEB(DEB_CMND, printk("scsi%d: id%d queuing ", host->host_no, cmd->target)); DEB(DEB_CMND, print_command(cmd->cmnd)); cmd->scsi_done = done; cmd->host_scribble = NULL; cmd->SCp.ptr = NULL; cmd->SCp.buffer = NULL; save_flags(flags); cli(); if (ignore_ids[hostdata->chip] & (1 << cmd->target)) { printk("scsi%d: ignoring target %d\n", host->host_no, cmd->target); cmd->result = (DID_BAD_TARGET << 16); done(cmd); restore_flags (flags); return 0; } #ifdef DEBUG_LIMIT_INTS if (sim710_intrs > DEBUG_LIMIT_INTS) { cmd->result = (DID_BAD_TARGET << 16); done(cmd); restore_flags (flags); return 0; } #endif if (cmd->use_sg > MAX_SG) panic ("cmd->use_sg = %d\n", cmd->use_sg); if (!(hostdata->issue_queue) || (cmd->cmnd[0] == REQUEST_SENSE)) { cmd->SCp.ptr = (unsigned char *) hostdata->issue_queue; hostdata->issue_queue = cmd; } else { for (tmp = hostdata->issue_queue; tmp->SCp.ptr; tmp = (Scsi_Cmnd *) tmp->SCp.ptr); tmp->SCp.ptr = (unsigned char *) cmd; } restore_flags (flags); run_process_issue_queue(hostdata); return 0; } __init int sim710_detect(Scsi_Host_Template * tpnt) { unsigned char scsi_id; unsigned int base_addr; struct Scsi_Host * host = NULL; struct sim710_hostdata *hostdata; unsigned long timeout; unsigned long irq_mask; int requested_irq; int probed_irq; u32 dsps; int chips = 0; int limit; int indx; int revision; int size; volatile u8 tmp; struct Scsi_Host *our_hosts[MAXBOARDS+1]; #ifdef MODULE if (sim710) param_setup(sim710); #endif if (no_of_boards < 0) { printk("sim710: NCR53C710 driver disabled\n"); return 0; } #ifdef CONFIG_MCA /* If board details have been specified via boot/module parameters, * then don't bother probing. */ if (no_of_boards == 0) { int slot; int pos[3]; int mca_53c710_ids[] = MCA_53C710_IDS; int *id_to_check = mca_53c710_ids; static int io_004f_by_pos[] = MCA_004F_IO_PORTS; static int irq_004f_by_pos[] = MCA_004F_IRQS; static int io_01bb_by_pos[] = MCA_01BB_IO_PORTS; static int irq_01bb_by_pos[] = MCA_01BB_IRQS; while ( *id_to_check && no_of_boards < MAXBOARDS) { if (!MCA_bus) return 0; if ((slot = mca_find_adapter(*id_to_check, 0)) != MCA_NOTFOUND) { pos[0] = mca_read_stored_pos(slot, 2); pos[1] = mca_read_stored_pos(slot, 3); pos[2] = mca_read_stored_pos(slot, 4); /* * 01BB & 01BA port base by bits 7,6,5,4,3,2 in pos[2] * * 000000 <disabled> 001010 0x2800 * 000001 <invalid> 001011 0x2C00 * 000010 0x0800 001100 0x3000 * 000011 0x0C00 001101 0x3400 * 000100 0x1000 001110 0x3800 * 000101 0x1400 001111 0x3C00 * 000110 0x1800 010000 0x4000 * 000111 0x1C00 010001 0x4400 * 001000 0x2000 010010 0x4800 * 001001 0x2400 010011 0x4C00 * 010100 0x5000 * * 00F4 port base by bits 3,2,1 in pos[0] * * 000 <disabled> 001 0x200 * 010 0x300 011 0x400 * 100 0x500 101 0x600 * * 01BB & 01BA IRQ is specified in pos[0] bits 7 and 6: * * 00 3 10 11 * 01 5 11 14 * * 00F4 IRQ specified by bits 6,5,4 in pos[0] * * 100 5 101 9 * 110 14 */ if ( *id_to_check == 0x01bb || *id_to_check == 0x01ba ) { bases[no_of_boards] = io_01bb_by_pos[(pos[2] & 0xFC) >> 2]; irq_vectors[no_of_boards] = irq_01bb_by_pos[((pos[0] & 0xC0) >> 6)]; if (bases[no_of_boards] == 0x0000) printk("sim710: NCR53C710 Adapter ID 0x01bb is disabled.\n"); else { no_of_boards++; if ( *id_to_check == 0x01bb ) mca_set_adapter_name( slot, "NCR 3360/3430 SCSI SubSystem" ); else mca_set_adapter_name(slot, "NCR Dual SIOP SCSI Host Adapter Board"); } } else if ( *id_to_check == 0x004f ) { bases[no_of_boards] = io_004f_by_pos[((pos[0] & 0x0E) >> 1)]; irq_vectors[no_of_boards] = irq_004f_by_pos[((pos[0] & 0x70) >> 4) - 4]; if (bases[no_of_boards] == 0x0000) printk("sim710: NCR53C710 Adapter ID 0x004f is disabled.\n"); else { no_of_boards++; mca_set_adapter_name(slot, "NCR 53c710 SCSI Host Adapter Board"); } } } id_to_check++; } } #endif #ifdef CONFIG_EISA /* Auto probe, if no boards specified in boot parameters */ if (no_of_boards == 0) { int io_addr; /* reverse probe, so my on-board controller at 0x9000 is always scsi0 */ for (io_addr = 0x9000; no_of_boards < MAXBOARDS && io_addr >= 0x1000; io_addr -= 0x1000) { if (request_region(io_addr, 0x40, "sim710") != NULL) { int id0 = inw(io_addr + 0xc80); int id1 = inw(io_addr + 0xc82); /* The on-board controller on my Proliant 2000 is 0x1044, * my EISA card is 0x1144. */ if (id0 == 0x110e && (id1 == 0x1044 || id1 == 0x1144)) { bases[no_of_boards] = io_addr; #if 0 /* This should detect the IRQ, but I havn't proved it for * myself. Leave the old probe code active for now, as * no-one has reported problems with it. */ switch (inb(io_addr + 0xc88)) { case (0x00): irq_vectors[no_of_boards] = 11; break; case (0x01): irq_vectors[no_of_boards] = 14; break; case (0x02): irq_vectors[no_of_boards] = 15; break; case (0x03): irq_vectors[no_of_boards] = 10; break; case (0x04): irq_vectors[no_of_boards] = 9; break; default: printk("sim710.c: irq nasty\n"); } #endif no_of_boards++; } release_region(io_addr, 64); } } } #endif if (!no_of_boards) { printk("sim710: No NCR53C710 adapter found.\n"); return 0; } size = sizeof(struct sim710_hostdata); hostdata_order = 0; while (size > (PAGE_SIZE << hostdata_order)) hostdata_order++; size = PAGE_SIZE << hostdata_order; DEB(DEB_ANY, printk("sim710: hostdata %d bytes, size %d, order %d\n", sizeof(struct sim710_hostdata), size, hostdata_order)); tpnt->proc_name = "sim710"; memset(our_hosts, 0, sizeof(our_hosts)); for (indx = 0; indx < no_of_boards; indx++) { unsigned long page = __get_free_pages(GFP_ATOMIC, hostdata_order); if(page == 0UL) { printk(KERN_WARNING "sim710: out of memory registering board %d.\n", indx); break; } host = scsi_register(tpnt, 4); if(host == NULL) { free_pages(host->hostdata[0], hostdata_order); break; } our_hosts[chips] = host; host->hostdata[0] = page; hostdata = (struct sim710_hostdata *)host->hostdata[0]; memset(hostdata, 0, size); scsi_id = 7; base_addr = bases[indx]; requested_irq = irq_vectors[indx]; printk("scsi%d: Configuring Sim710 (SCSI-ID %d) at %x, IRQ %d\n", host->host_no, scsi_id, base_addr, requested_irq); DEB(DEB_ANY, printk("sim710: hostdata = %p (%d bytes), dsa0 = %p\n", hostdata, sizeof(struct sim710_hostdata), hostdata->target[0].dsa)); hostdata->chip = indx; host->irq = requested_irq; host->this_id = scsi_id; host->unique_id = base_addr; host->base = base_addr; hostdata->msg_reject = MESSAGE_REJECT; if (ncr_halt(host)) { free_pages(host->hostdata[0], hostdata_order); scsi_unregister (host); printk("scsi%d: Failed to initialise 53c710 at address %x\n", host->host_no, base_addr); continue; } DEB(DEB_ANY,ncr_dump(host)); revision = (NCR_read8(CTEST8_REG) & 0xF0) >> 4; printk("scsi%d: Revision 0x%x\n",host->host_no,revision); sim710_soft_reset(host); sim710_driver_init(host); request_region((u32)host->base, 64, "sim710"); /* Now run test1 */ hostdata->test1_src = 0x53c710aa; hostdata->test1_dst = 0x76543210; NCR_write32(DSPS_REG, 0x89abcdef); irq_mask = probe_irq_on(); NCR_write32(DSP_REG, virt_to_bus(hostdata->script+Ent_test1/4)); timeout = 5; while (hostdata->test1_dst != hostdata->test1_src && timeout--) mdelay(100); tmp = NCR_read8(ISTAT_REG); tmp = NCR_read8(SSTAT0_REG); udelay(10); tmp = NCR_read8(DSTAT_REG); probed_irq = probe_irq_off(irq_mask); if (requested_irq == 0) { if (probed_irq > 0) { printk("scsi%d: Chip is using IRQ %d\n", host->host_no, probed_irq); requested_irq = host->irq = probed_irq; } else { printk("scsi%d: Failed to probe for IRQ (returned %d)\n", host->host_no, probed_irq); ncr_halt(host); free_pages(host->hostdata[0], hostdata_order); scsi_unregister (host); release_region((u32)host->base, 64); continue; } } else if (probed_irq > 0 && probed_irq != requested_irq) printk("scsi%d: WARNING requested IRQ %d, but probed as %d\n", host->host_no, requested_irq, probed_irq); else if (probed_irq <= 0) printk("scsi%d: WARNING IRQ probe failed, (returned %d)\n", host->host_no, probed_irq); dsps = NCR_read32(DSPS_REG); if (hostdata->test1_dst != 0x53c710aa || dsps != A_int_test1) { if (hostdata->test1_dst != 0x53c710aa) printk("scsi%d: test 1 FAILED: data: exp 0x53c710aa, got 0x%08x\n", host->host_no, hostdata->test1_dst); if (dsps != A_int_test1) printk("scsi%d: test 1 FAILED: dsps: exp 0x%08x, got 0x%08x\n", host->host_no, A_int_test1, dsps); ncr_dump(host); ncr_halt(host); free_pages(host->hostdata[0], hostdata_order); scsi_unregister (host); release_region((u32)host->base, 64); continue; } printk("scsi%d: test 1 completed ok.\n", host->host_no); NCR_write32(DSP_REG, virt_to_bus(hostdata->script+Ent_reselect/4)); hostdata->state = STATE_IDLE; chips++; } /* OK, now run down our_hosts[] calling request_irq(... SA_SHIRQ ...). * Couldn't call request_irq earlier, as probing would have failed. */ for (indx = 0, limit = chips; indx < limit; indx++) { host = our_hosts[indx]; if (request_irq(host->irq, do_sim710_intr_handle, SA_INTERRUPT | SA_SHIRQ, "sim710", host)) { printk("scsi%d : IRQ%d not free, detaching\n", host->host_no, host->irq); ncr_halt(host); free_pages(host->hostdata[0], hostdata_order); scsi_unregister (host); chips--; } } return chips; } int sim710_abort(Scsi_Cmnd * cmd) { struct Scsi_Host * host = cmd->host; printk("scsi%d: Unable to abort command for target %d\n", host->host_no, cmd->target); return FAILED; } /* * This is a device reset. Need to select and send a Bus Device Reset msg. */ int sim710_dev_reset(Scsi_Cmnd * SCpnt) { struct Scsi_Host * host = SCpnt->host; printk("scsi%d: Unable to send Bus Device Reset for target %d\n", host->host_no, SCpnt->target); return FAILED; } /* * This is bus reset. We need to reset the bus and fail any active commands. */ int sim710_bus_reset(Scsi_Cmnd * SCpnt) { struct Scsi_Host * host = SCpnt->host; printk("scsi%d: Unable to do SCSI bus reset\n", host->host_no); return FAILED; } static int full_reset(struct Scsi_Host * host) { struct sim710_hostdata *hostdata = (struct sim710_hostdata *) host->hostdata[0]; int target; Scsi_Cmnd *cmd; u32 istat, dstat = 0, sstat0 = 0, sstat1 = 0, dsp, dsps, scratch; unsigned long flags; save_flags(flags); cli(); istat = NCR_read8(ISTAT_REG); if (istat & ISTAT_SIP) { sstat0 = NCR_read8(SSTAT0_REG); sstat1 = NCR_read8(SSTAT1_REG); udelay(10); } if (istat & ISTAT_DIP) dstat = NCR_read8(DSTAT_REG); if (ncr_halt(host)) { restore_flags(flags); return FAILED; } restore_flags(flags); dsp = NCR_read32(DSP_REG); dsps = NCR_read32(DSPS_REG); scratch = NCR_read32(SCRATCH_REG); printk("scsi%d: istat = %02x, sstat0 = %02x, sstat1 = %02x, dstat = %02x\n", host->host_no, istat, sstat0, sstat1, dstat); printk("scsi%d: dsp = %08x (script[0x%04x]), dsps = %08x, scratch = %08x\n", host->host_no, dsp, ((u32)bus_to_virt(dsp) - (u32)hostdata->script)/4, dsps, scratch); for (target = 0; target < 7; target++) { if ((cmd = hostdata->target[target].cur_cmd)) { printk("scsi%d: Failing command for ID%d\n", host->host_no, target); cmd->result = DID_RESET << 16; cmd->scsi_done(cmd); hostdata->target[target].cur_cmd = NULL; } } sim710_soft_reset(host); sim710_driver_init(host); NCR_write32(DSP_REG, virt_to_bus(hostdata->script+Ent_reselect/4)); hostdata->state = STATE_IDLE; run_process_issue_queue(hostdata); return SUCCESS; } /* * This is host reset. We need to reset the chip and the bus. */ int sim710_host_reset(Scsi_Cmnd * SCpnt) { struct Scsi_Host * host = SCpnt->host; printk("scsi%d: >>>>>>>>>>>> Host reset <<<<<<<<<<<<\n", host->host_no); return full_reset(host); } #ifdef MODULE int sim710_release(struct Scsi_Host *host) { ncr_halt(host); free_pages(host->hostdata[0], hostdata_order); free_irq(host->irq, host); release_region((u32)host->base, 64); return 1; } #endif static Scsi_Host_Template driver_template = SIM710_SCSI; #include "scsi_module.c"
Go to most recent revision | Compare with Previous | Blame | View Log