OpenCores
URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [block/] [Config.in] - Rev 1765

Compare with Previous | Blame | View Log

#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Floppy, IDE, and other block devices'

tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
bool 'Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support' CONFIG_BLK_DEV_IDE
comment 'Please see Documentation/ide.txt for help/info on IDE drives'
if [ "$CONFIG_BLK_DEV_IDE" = "n" ]; then
  bool 'Old harddisk (MFM/RLL/IDE) driver' CONFIG_BLK_DEV_HD_ONLY
else
  bool '   Use old disk-only driver on primary interface' CONFIG_BLK_DEV_HD_IDE
  if [ "$CONFIG_BLK_DEV_HD_IDE" != "n" ]; then
    bool '     Use multi-mode by default' CONFIG_IDEDISK_MULTI_MODE
  fi
  bool '   Include IDE/ATAPI CDROM support' CONFIG_BLK_DEV_IDECD
  bool '   Include IDE/ATAPI TAPE support' CONFIG_BLK_DEV_IDETAPE
  bool '   Include IDE/ATAPI FLOPPY support (new)' CONFIG_BLK_DEV_IDEFLOPPY
  bool '   SCSI emulation support' CONFIG_BLK_DEV_IDESCSI
  bool '   Support removable IDE interfaces (PCMCIA)' CONFIG_BLK_DEV_IDE_PCMCIA
  bool '   CMD640 chipset bugfix/support' CONFIG_BLK_DEV_CMD640
  if [ "$CONFIG_BLK_DEV_CMD640" = "y" ]; then
    bool '     CMD640 enhanced support' CONFIG_BLK_DEV_CMD640_ENHANCED
  fi
  if [ "$CONFIG_PCI" = "y" ]; then
    bool '   RZ1000 chipset bugfix/support' CONFIG_BLK_DEV_RZ1000
    bool '   Intel 82371 PIIX (Triton I/II) DMA support' CONFIG_BLK_DEV_TRITON
    if [ "$CONFIG_BLK_DEV_TRITON" = "y" ]; then
      bool '     Boot off-board chipsets first support' CONFIG_BLK_DEV_OFFBOARD
    fi
  fi
  bool '   Other IDE chipset support' CONFIG_IDE_CHIPSETS
  if [ "$CONFIG_IDE_CHIPSETS" = "y" ]; then
    comment 'Note: most of these also require special kernel boot parameters'
    bool '      ALI M14xx       support' CONFIG_BLK_DEV_ALI14XX
    bool '      DTC-2278        support' CONFIG_BLK_DEV_DTC2278
    bool '      Holtek HT6560B  support' CONFIG_BLK_DEV_HT6560B
    if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
      bool '      PROMISE DC4030  support (EXPERIMENTAL)' CONFIG_BLK_DEV_PROMISE
    fi
    bool '      QDI QD6580      support' CONFIG_BLK_DEV_QD6580
    bool '      UMC 8672        support' CONFIG_BLK_DEV_UMC8672
  fi
fi

comment 'Additional Block Devices'

tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
bool 'Multiple devices driver support' CONFIG_BLK_DEV_MD
if [ "$CONFIG_BLK_DEV_MD" = "y" ]; then
  tristate '   Linear (append) mode' CONFIG_MD_LINEAR
  tristate '   RAID-0 (striping) mode' CONFIG_MD_STRIPED
  tristate '   RAID-1 (mirroring) mode' CONFIG_MD_MIRRORING
  tristate '   RAID-4/RAID-5 mode' CONFIG_MD_RAID5
fi
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" ]; then
  bool '   Release empty RAM disk blocks' CONFIG_RD_RELEASE_BLOCKS
  bool '   Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD
fi
tristate 'ROM disk memory block device' CONFIG_BLK_DEV_BLKMEM
tristate 'XT harddisk support' CONFIG_BLK_DEV_XD
if [ "$CONFIG_PCI" = "y" ]; then
  bool 'Mylex DAC960 PCI RAID Controller support' CONFIG_BLK_DEV_DAC960
fi

tristate 'Compaq SMART2 support' CONFIG_BLK_CPQ_DA
if [ "$CONFIG_BLK_CPQ_DA" = "y" -o "$CONFIG_BLK_CPQ_DA" = "m" ]; then
  bool '   Support for PCI SMART-2 Controllers' CONFIG_BLK_CPQ_DA_PCI
  bool '   Support for EISA SMART-2 Controllers' CONFIG_BLK_CPQ_DA_EISA
fi

tristate 'Parallel port IDE device support' CONFIG_PARIDE 
if [ "$CONFIG_PARIDE" = "y" -o "$CONFIG_PARIDE" = "m" ]; then
  source drivers/block/paride/Config.in
fi

if [ "$CONFIG_BLK_DEV_HD_IDE" = "y" -o "$CONFIG_BLK_DEV_HD_ONLY" = "y" ]; then
  define_bool CONFIG_BLK_DEV_HD y
else
  define_bool CONFIG_BLK_DEV_HD n
fi

endmenu

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.