URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [block/] [ide.h] - Rev 1765
Compare with Previous | Blame | View Log
/* * linux/drivers/block/ide.h * * Copyright (C) 1994, 1995 Linus Torvalds & authors */ #include <linux/config.h> /* * This is the multiple IDE interface driver, as evolved from hd.c. * It supports up to four IDE interfaces, on one or more IRQs (usually 14 & 15). * There can be up to two drives per interface, as per the ATA-2 spec. * * Primary i/f: ide0: major=3; (hda) minor=0; (hdb) minor=64 * Secondary i/f: ide1: major=22; (hdc or hd1a) minor=0; (hdd or hd1b) minor=64 * Tertiary i/f: ide2: major=33; (hde) minor=0; (hdf) minor=64 * Quaternary i/f: ide3: major=34; (hdg) minor=0; (hdh) minor=64 */ /****************************************************************************** * IDE driver configuration options (play with these as desired): * * REALLY_SLOW_IO can be defined in ide.c and ide-cd.c, if necessary */ #undef REALLY_FAST_IO /* define if ide ports are perfect */ #define INITIAL_MULT_COUNT 0 /* off=0; on=2,4,8,16,32, etc.. */ #ifdef CONFIG_COLDFIRE /* * ColdFire board specifics... */ #define SUPPORT_VLB_SYNC 0 /* No VLB on ColdFires */ #define MAX_HWIFS 1 /* Only 1 interface */ #endif #ifndef SUPPORT_SLOW_DATA_PORTS /* 1 to support slow data ports */ #define SUPPORT_SLOW_DATA_PORTS 1 /* 0 to reduce kernel size */ #endif #ifndef SUPPORT_VLB_SYNC /* 1 to support weird 32-bit chips */ #define SUPPORT_VLB_SYNC 1 /* 0 to reduce kernel size */ #endif #ifndef DISK_RECOVERY_TIME /* off=0; on=access_delay_time */ #define DISK_RECOVERY_TIME 0 /* for hardware that needs it */ #endif #ifndef OK_TO_RESET_CONTROLLER /* 1 needed for good error recovery */ #define OK_TO_RESET_CONTROLLER 1 /* 0 for use with AH2372A/B interface */ #endif #ifndef FAKE_FDISK_FOR_EZDRIVE /* 1 to help linux fdisk with EZDRIVE */ #define FAKE_FDISK_FOR_EZDRIVE 1 /* 0 to reduce kernel size */ #endif #ifndef FANCY_STATUS_DUMPS /* 1 for human-readable drive errors */ #define FANCY_STATUS_DUMPS 1 /* 0 to reduce kernel size */ #endif #ifdef CONFIG_BLK_DEV_CMD640 #if 0 /* change to 1 when debugging cmd640 problems */ void cmd640_dump_regs (void); #define CMD640_DUMP_REGS cmd640_dump_regs() /* for debugging cmd640 chipset */ #endif #endif /* CONFIG_BLK_DEV_CMD640 */ #if defined(CONFIG_BLK_DEV_IDECD) || defined(CONFIG_BLK_DEV_IDETAPE) || \ defined(CONFIG_BLK_DEV_IDEFLOPPY) || defined(CONFIG_BLK_DEV_IDESCSI) #define CONFIG_BLK_DEV_IDEATAPI 1 #endif /* * IDE_DRIVE_CMD is used to implement many features of the hdparm utility */ #define IDE_DRIVE_CMD 99 /* (magic) undef to reduce kernel size*/ /* * "No user-serviceable parts" beyond this point :) *****************************************************************************/ #if defined(CONFIG_BLK_DEV_IDESCSI) && !defined(CONFIG_SCSI) #error "SCSI must also be selected" #endif typedef unsigned char byte; /* used everywhere */ /* * Probably not wise to fiddle with these */ #define ERROR_MAX 8 /* Max read/write errors per sector */ #define ERROR_RESET 3 /* Reset controller every 4th retry */ #define ERROR_RECAL 1 /* Recalibrate every 2nd retry */ /* * Ensure that various configuration flags have compatible settings */ #ifdef REALLY_SLOW_IO #undef REALLY_FAST_IO #endif /* * Definitions for accessing IDE controller registers */ #define HWIF(drive) ((ide_hwif_t *)((drive)->hwif)) #define HWGROUP(drive) ((ide_hwgroup_t *)(HWIF(drive)->hwgroup)) #define IDE_DATA_OFFSET (0) #define IDE_ERROR_OFFSET (1) #define IDE_NSECTOR_OFFSET (2) #define IDE_SECTOR_OFFSET (3) #define IDE_LCYL_OFFSET (4) #define IDE_HCYL_OFFSET (5) #define IDE_SELECT_OFFSET (6) #define IDE_STATUS_OFFSET (7) #define IDE_FEATURE_OFFSET IDE_ERROR_OFFSET #define IDE_COMMAND_OFFSET IDE_STATUS_OFFSET #define IDE_DATA_REG (HWIF(drive)->io_base+IDE_DATA_OFFSET) #define IDE_ERROR_REG (HWIF(drive)->io_base+IDE_ERROR_OFFSET) #define IDE_NSECTOR_REG (HWIF(drive)->io_base+IDE_NSECTOR_OFFSET) #define IDE_SECTOR_REG (HWIF(drive)->io_base+IDE_SECTOR_OFFSET) #define IDE_LCYL_REG (HWIF(drive)->io_base+IDE_LCYL_OFFSET) #define IDE_HCYL_REG (HWIF(drive)->io_base+IDE_HCYL_OFFSET) #define IDE_SELECT_REG (HWIF(drive)->io_base+IDE_SELECT_OFFSET) #define IDE_STATUS_REG (HWIF(drive)->io_base+IDE_STATUS_OFFSET) #define IDE_CONTROL_REG (HWIF(drive)->ctl_port) #define IDE_FEATURE_REG IDE_ERROR_REG #define IDE_COMMAND_REG IDE_STATUS_REG #define IDE_ALTSTATUS_REG IDE_CONTROL_REG #define IDE_IREASON_REG IDE_NSECTOR_REG #define IDE_BCOUNTL_REG IDE_LCYL_REG #define IDE_BCOUNTH_REG IDE_HCYL_REG #ifdef REALLY_FAST_IO #define OUT_BYTE(b,p) outb((b),(p)) #define IN_BYTE(p) (byte)inb(p) #else #define OUT_BYTE(b,p) outb_p((b),(p)) #define IN_BYTE(p) (byte)inb_p(p) #endif /* REALLY_FAST_IO */ #define GET_ERR() IN_BYTE(IDE_ERROR_REG) #define GET_STAT() IN_BYTE(IDE_STATUS_REG) #define OK_STAT(stat,good,bad) (((stat)&((good)|(bad)))==(good)) #define BAD_R_STAT (BUSY_STAT | ERR_STAT) #define BAD_W_STAT (BAD_R_STAT | WRERR_STAT) #define BAD_STAT (BAD_R_STAT | DRQ_STAT) #define DRIVE_READY (READY_STAT | SEEK_STAT) #define DATA_READY (DRQ_STAT) /* * Some more useful definitions */ #define IDE_MAJOR_NAME "ide" /* the same for all i/f; see also genhd.c */ #define MAJOR_NAME IDE_MAJOR_NAME #define PARTN_BITS 6 /* number of minor dev bits for partitions */ #define PARTN_MASK ((1<<PARTN_BITS)-1) /* a useful bit mask */ #define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */ #ifndef MAX_HWIFS #define MAX_HWIFS 4 /* an arbitrary, but realistic limit */ #endif #define SECTOR_WORDS (512 / 4) /* number of 32bit words per sector */ /* * Timeouts for various operations: */ #define WAIT_DRQ (5*HZ/100) /* 50msec - spec allows up to 20ms */ #ifdef CONFIG_APM #define WAIT_READY (5*HZ) /* 5sec - some laptops are very slow */ #else #define WAIT_READY (3*HZ/100) /* 30msec - should be instantaneous */ #endif /* CONFIG_APM */ #define WAIT_PIDENTIFY (1*HZ) /* 1sec - should be less than 3ms (?) */ #define WAIT_WORSTCASE (30*HZ) /* 30sec - worst case when spinning up */ #define WAIT_CMD (10*HZ) /* 10sec - maximum wait for an IRQ to happen */ #if defined(CONFIG_BLK_DEV_HT6560B) || defined(CONFIG_BLK_DEV_PROMISE) #define SELECT_DRIVE(hwif,drive) \ { \ if (hwif->selectproc) \ hwif->selectproc(drive); \ else \ OUT_BYTE((drive)->select.all, hwif->io_base+IDE_SELECT_OFFSET); \ } #else #define SELECT_DRIVE(hwif,drive) OUT_BYTE((drive)->select.all, hwif->io_base+IDE_SELECT_OFFSET); #endif /* CONFIG_BLK_DEV_HT6560B || CONFIG_BLK_DEV_PROMISE */ #ifdef CONFIG_BLK_DEV_IDETAPE #include "ide-tape.h" #endif /* CONFIG_BLK_DEV_IDETAPE */ #ifdef CONFIG_BLK_DEV_IDECD struct atapi_request_sense { unsigned char error_code : 7; unsigned char valid : 1; byte reserved1; unsigned char sense_key : 4; unsigned char reserved2 : 1; unsigned char ili : 1; unsigned char reserved3 : 2; byte info[4]; byte sense_len; byte command_info[4]; byte asc; byte ascq; byte fru; byte sense_key_specific[3]; }; struct packet_command { char *buffer; int buflen; int stat; struct atapi_request_sense *sense_data; unsigned char c[12]; }; /* Structure of a MSF cdrom address. */ struct atapi_msf { byte reserved; byte minute; byte second; byte frame; }; /* Space to hold the disk TOC. */ #define MAX_TRACKS 99 struct atapi_toc_header { unsigned short toc_length; byte first_track; byte last_track; }; struct atapi_toc_entry { byte reserved1; unsigned control : 4; unsigned adr : 4; byte track; byte reserved2; union { unsigned lba; struct atapi_msf msf; } addr; }; struct atapi_toc { int last_session_lba; int xa_flag; unsigned capacity; struct atapi_toc_header hdr; struct atapi_toc_entry ent[MAX_TRACKS+1]; /* One extra for the leadout. */ }; /* This structure is annoyingly close to, but not identical with, the cdrom_subchnl structure from cdrom.h. */ struct atapi_cdrom_subchnl { u_char acdsc_reserved; u_char acdsc_audiostatus; u_short acdsc_length; u_char acdsc_format; u_char acdsc_adr: 4; u_char acdsc_ctrl: 4; u_char acdsc_trk; u_char acdsc_ind; union { struct atapi_msf msf; int lba; } acdsc_absaddr; union { struct atapi_msf msf; int lba; } acdsc_reladdr; }; /* Extra per-device info for cdrom drives. */ struct cdrom_info { /* Buffer for table of contents. NULL if we haven't allocated a TOC buffer for this device yet. */ struct atapi_toc *toc; /* Sector buffer. If a read request wants only the first part of a cdrom block, we cache the rest of the block here, in the expectation that that data is going to be wanted soon. SECTOR_BUFFERED is the number of the first buffered sector, and NSECTORS_BUFFERED is the number of sectors in the buffer. Before the buffer is allocated, we should have SECTOR_BUFFER == NULL and NSECTORS_BUFFERED == 0. */ unsigned long sector_buffered; unsigned long nsectors_buffered; char *sector_buffer; /* The result of the last successful request sense command on this device. */ struct atapi_request_sense sense_data; int max_sectors; }; #endif /* CONFIG_BLK_DEV_IDECD */ /* * Now for the data we need to maintain per-drive: ide_drive_t */ typedef enum {ide_disk, ide_cdrom, ide_tape, ide_floppy, ide_scsi} ide_media_t; typedef union { unsigned all : 8; /* all of the bits together */ struct { unsigned set_geometry : 1; /* respecify drive geometry */ unsigned recalibrate : 1; /* seek to cyl 0 */ unsigned set_multmode : 1; /* set multmode count */ unsigned set_tune : 1; /* tune interface for drive */ unsigned mc : 1; /* acknowledge media change */ unsigned reserved : 3; /* unused */ } b; } special_t; typedef union { unsigned all : 8; /* all of the bits together */ struct { unsigned head : 4; /* always zeros here */ unsigned unit : 1; /* drive select number, 0 or 1 */ unsigned bit5 : 1; /* always 1 */ unsigned lba : 1; /* using LBA instead of CHS */ unsigned bit7 : 1; /* always 1 */ } b; } select_t; typedef struct ide_drive_s { special_t special; /* special action flags */ unsigned present : 1; /* drive is physically present */ unsigned noprobe : 1; /* from: hdx=noprobe */ unsigned keep_settings : 1; /* restore settings after drive reset */ unsigned busy : 1; /* currently doing revalidate_disk() */ unsigned removable : 1; /* 1 if need to do check_media_change */ unsigned using_dma : 1; /* disk is using dma for read/write */ unsigned forced_geom : 1; /* 1 if hdx=c,h,s was given at boot */ unsigned unmask : 1; /* flag: okay to unmask other irqs */ unsigned no_unmask : 1; /* disallow setting unmask bit */ unsigned no_io_32bit : 1; /* disallow enabling 32bit I/O */ unsigned nobios : 1; /* flag: do not probe bios for drive */ unsigned slow : 1; /* flag: slow data port */ unsigned autotune : 2; /* 1=autotune, 2=noautotune, 0=default */ #if FAKE_FDISK_FOR_EZDRIVE unsigned remap_0_to_1 : 1; /* flag: partitioned with ezdrive */ #endif /* FAKE_FDISK_FOR_EZDRIVE */ unsigned no_geom : 1; /* flag: do not set geometry */ ide_media_t media; /* disk, cdrom, tape, floppy */ select_t select; /* basic drive/head select reg value */ byte ctl; /* "normal" value for IDE_CONTROL_REG */ byte ready_stat; /* min status value for drive ready */ byte mult_count; /* current multiple sector setting */ byte mult_req; /* requested multiple sector setting */ byte tune_req; /* requested drive tuning setting */ byte io_32bit; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */ byte bad_wstat; /* used for ignoring WRERR_STAT */ byte sect0; /* offset of first sector for DM6:DDO */ byte usage; /* current "open()" count for drive */ byte head; /* "real" number of heads */ byte sect; /* "real" sectors per track */ byte bios_head; /* BIOS/fdisk/LILO number of heads */ byte bios_sect; /* BIOS/fdisk/LILO sectors per track */ unsigned short bios_cyl; /* BIOS/fdisk/LILO number of cyls */ unsigned short cyl; /* "real" number of cyls */ void *hwif; /* actually (ide_hwif_t *) */ struct wait_queue *wqueue; /* used to wait for drive in open() */ struct hd_driveid *id; /* drive model identification info */ struct hd_struct *part; /* drive partition table */ char name[4]; /* drive name, such as "hda" */ #ifdef CONFIG_BLK_DEV_IDECD struct cdrom_info cdrom_info; /* for ide-cd.c */ #endif /* CONFIG_BLK_DEV_IDECD */ #ifdef CONFIG_BLK_DEV_IDETAPE idetape_tape_t tape; /* for ide-tape.c */ #endif /* CONFIG_BLK_DEV_IDETAPE */ #ifdef CONFIG_BLK_DEV_IDEFLOPPY void *floppy; /* for ide-floppy.c */ #endif /* CONFIG_BLK_DEV_IDEFLOPPY */ #ifdef CONFIG_BLK_DEV_IDESCSI void *scsi; /* for ide-scsi.c */ #endif /* CONFIG_BLK_DEV_IDESCSI */ byte ide_scsi; /* use ide-scsi driver */ } ide_drive_t; /* * An ide_dmaproc_t() initiates/aborts DMA read/write operations on a drive. * * The caller is assumed to have selected the drive and programmed the drive's * sector address using CHS or LBA. All that remains is to prepare for DMA * and then issue the actual read/write DMA/PIO command to the drive. * * Returns 0 if all went well. * Returns 1 if DMA read/write could not be started, in which case the caller * should either try again later, or revert to PIO for the current request. */ typedef enum { ide_dma_read = 0, ide_dma_write = 1, ide_dma_abort = 2, ide_dma_check = 3, ide_dma_status_bad = 4, ide_dma_transferred = 5, ide_dma_begin = 6 } ide_dma_action_t; typedef int (ide_dmaproc_t)(ide_dma_action_t, ide_drive_t *); /* * An ide_tuneproc_t() is used to set the speed of an IDE interface * to a particular PIO mode. The "byte" parameter is used * to select the PIO mode by number (0,1,2,3,4,5), and a value of 255 * indicates that the interface driver should "auto-tune" the PIO mode * according to the drive capabilities in drive->id; * * Not all interface types support tuning, and not all of those * support all possible PIO settings. They may silently ignore * or round values as they see fit. */ typedef void (ide_tuneproc_t)(ide_drive_t *, byte); /* * This is used to provide HT6560B & PROMISE interface support. */ typedef void (ide_selectproc_t) (ide_drive_t *); /* * hwif_chipset_t is used to keep track of the specific hardware * chipset used by each IDE interface, if known. */ typedef enum { ide_unknown, ide_generic, ide_triton, ide_cmd640, ide_dtc2278, ide_ali14xx, ide_qd6580, ide_umc8672, ide_ht6560b, ide_promise, ide_udma } hwif_chipset_t; typedef struct hwif_s { struct hwif_s *next; /* for linked-list in ide_hwgroup_t */ void *hwgroup; /* actually (ide_hwgroup_t *) */ #ifdef CONFIG_COLDFIRE unsigned int io_base; /* base io port addr */ unsigned int ctl_port; /* usually io_base+0x206 */ #else unsigned short io_base; /* base io port addr */ unsigned short ctl_port; /* usually io_base+0x206 */ #endif ide_drive_t drives[MAX_DRIVES]; /* drive info */ struct gendisk *gd; /* gendisk structure */ ide_tuneproc_t *tuneproc; /* routine to tune PIO mode for drives */ #if defined(CONFIG_BLK_DEV_HT6560B) || defined(CONFIG_BLK_DEV_PROMISE) ide_selectproc_t *selectproc; /* tweaks hardware to select drive */ #endif ide_dmaproc_t *dmaproc; /* dma read/write/abort routine */ unsigned long *dmatable; /* dma physical region descriptor table */ unsigned short dma_base; /* base addr for dma ports (triton) */ byte irq; /* our irq number */ byte major; /* our major number */ char name[5]; /* name of interface, eg. "ide0" */ byte index; /* 0 for ide0; 1 for ide1; ... */ hwif_chipset_t chipset; /* sub-module for tuning.. */ unsigned noprobe : 1; /* don't probe for this interface */ unsigned present : 1; /* this interface exists */ unsigned serialized : 1; /* serialized operation with mate hwif */ unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */ #ifdef CONFIG_BLK_DEV_PROMISE unsigned is_promise2: 1; /* 2nd i/f on promise DC4030 */ #endif /* CONFIG_BLK_DEV_PROMISE */ #if (DISK_RECOVERY_TIME > 0) unsigned long last_time; /* time when previous rq was done */ #endif #ifdef CONFIG_BLK_DEV_IDECD struct request request_sense_request; /* from ide-cd.c */ struct packet_command request_sense_pc; /* from ide-cd.c */ #endif /* CONFIG_BLK_DEV_IDECD */ #ifdef CONFIG_BLK_DEV_IDETAPE ide_drive_t *tape_drive; /* Pointer to the tape on this interface */ #endif /* CONFIG_BLK_DEV_IDETAPE */ } ide_hwif_t; /* * internal ide interrupt handler type */ typedef void (ide_handler_t)(ide_drive_t *); typedef struct hwgroup_s { ide_handler_t *handler;/* irq handler, if active */ ide_drive_t *drive; /* current drive */ ide_hwif_t *hwif; /* ptr to current hwif in linked-list */ ide_hwif_t *next_hwif; /* next selected hwif (for tape) */ struct request *rq; /* current request */ struct timer_list timer; /* failsafe timer */ struct request wrq; /* local copy of current write rq */ unsigned long poll_timeout; /* timeout value during long polls */ int active; /* set when servicing requests */ } ide_hwgroup_t; /* * ide_hwifs[] is the master data structure used to keep track * of just about everything in ide.c. Whenever possible, routines * should be using pointers to a drive (ide_drive_t *) or * pointers to a hwif (ide_hwif_t *), rather than indexing this * structure directly (the allocation/layout may change!). * */ #ifndef _IDE_C extern ide_hwif_t ide_hwifs[]; /* master data repository */ #endif /* * One final include file, which references some of the data/defns from above */ #define IDE_DRIVER /* "parameter" for blk.h */ #include <linux/blk.h> #if (DISK_RECOVERY_TIME > 0) void ide_set_recovery_timer (ide_hwif_t *); #define SET_RECOVERY_TIMER(drive) ide_set_recovery_timer (drive) #else #define SET_RECOVERY_TIMER(drive) #endif /* * This is used for (nearly) all data transfers from the IDE interface */ void ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount); /* * This is used for (nearly) all data transfers to the IDE interface */ void ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount); /* * This is used for (nearly) all ATAPI data transfers from/to the IDE interface */ void atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount); void atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount); /* * This is used on exit from the driver, to designate the next irq handler * and also to start the safety timer. */ void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout); /* * Error reporting, in human readable form (luxurious, but a memory hog). */ byte ide_dump_status (ide_drive_t *drive, const char *msg, byte stat); /* * ide_error() takes action based on the error returned by the controller. * The calling function must return afterwards, to restart the request. */ void ide_error (ide_drive_t *drive, const char *msg, byte stat); /* * ide_fixstring() cleans up and (optionally) byte-swaps a text string, * removing leading/trailing blanks and compressing internal blanks. * It is primarily used to tidy up the model name/number fields as * returned by the WIN_[P]IDENTIFY commands. */ void ide_fixstring (byte *s, const int bytecount, const int byteswap); /* * This routine busy-waits for the drive status to be not "busy". * It then checks the status for all of the "good" bits and none * of the "bad" bits, and if all is okay it returns 0. All other * cases return 1 after invoking ide_error() -- caller should return. * */ int ide_wait_stat (ide_drive_t *drive, byte good, byte bad, unsigned long timeout); /* * This routine is called from the partition-table code in genhd.c * to "convert" a drive to a logical geometry with fewer than 1024 cyls. * * The second parameter, "xparm", determines exactly how the translation * will be handled: * 0 = convert to CHS with fewer than 1024 cyls * using the same method as Ontrack DiskManager. * 1 = same as "0", plus offset everything by 63 sectors. * -1 = similar to "0", plus redirect sector 0 to sector 1. * >1 = convert to a CHS geometry with "xparm" heads. * * Returns 0 if the translation was not possible, if the device was not * an IDE disk drive, or if a geometry was "forced" on the commandline. * Returns 1 if the geometry translation was successful. */ int ide_xlate_1024 (kdev_t, int, const char *); /* * Start a reset operation for an IDE interface. * The caller should return immediately after invoking this. */ void ide_do_reset (ide_drive_t *); /* * This function is intended to be used prior to invoking ide_do_drive_cmd(). */ void ide_init_drive_cmd (struct request *rq); /* * "action" parameter type for ide_do_drive_cmd() below. */ typedef enum {ide_wait, /* insert rq at end of list, and wait for it */ ide_next, /* insert rq immediately after current request */ ide_preempt, /* insert rq in front of current request */ ide_end} /* insert rq at end of list, but don't wait for it */ ide_action_t; /* * This function issues a special IDE device request * onto the request queue. * * If action is ide_wait, then the rq is queued at the end of the * request queue, and the function sleeps until it has been processed. * This is for use when invoked from an ioctl handler. * * If action is ide_preempt, then the rq is queued at the head of * the request queue, displacing the currently-being-processed * request and this function returns immediately without waiting * for the new rq to be completed. This is VERY DANGEROUS, and is * intended for careful use by the ATAPI tape/cdrom driver code. * * If action is ide_next, then the rq is queued immediately after * the currently-being-processed-request (if any), and the function * returns without waiting for the new rq to be completed. As above, * This is VERY DANGEROUS, and is intended for careful use by the * ATAPI tape/cdrom driver code. * * If action is ide_end, then the rq is queued at the end of the * request queue, and the function returns immediately without waiting * for the new rq to be completed. This is again intended for careful * use by the ATAPI tape/cdrom driver code. (Currently used by ide-tape.c, * when operating in the pipelined operation mode). */ int ide_do_drive_cmd (ide_drive_t *drive, struct request *rq, ide_action_t action); /* * Clean up after success/failure of an explicit drive cmd. * stat/err are used only when (HWGROUP(drive)->rq->cmd == IDE_DRIVE_CMD). */ void ide_end_drive_cmd (ide_drive_t *drive, byte stat, byte err); /* * ide_system_bus_speed() returns what we think is the system VESA/PCI * bus speed (in Mhz). This is used for calculating interface PIO timings. * The default is 40 for known PCI systems, 50 otherwise. * The "idebus=xx" parameter can be used to override this value. */ int ide_system_bus_speed (void); /* * ide_multwrite() transfers a block of up to mcount sectors of data * to a drive as part of a disk multwrite operation. */ void ide_multwrite (ide_drive_t *drive, unsigned int mcount); #ifdef CONFIG_BLK_DEV_IDECD /* * These are routines in ide-cd.c invoked from ide.c */ void ide_do_rw_cdrom (ide_drive_t *, unsigned long); int ide_cdrom_ioctl (ide_drive_t *, struct inode *, struct file *, unsigned int, unsigned long); int ide_cdrom_check_media_change (ide_drive_t *); int ide_cdrom_open (struct inode *, struct file *, ide_drive_t *); void ide_cdrom_release (struct inode *, struct file *, ide_drive_t *); void ide_cdrom_setup (ide_drive_t *); #endif /* CONFIG_BLK_DEV_IDECD */ #ifdef CONFIG_BLK_DEV_IDETAPE /* * Functions in ide-tape.c which are invoked from ide.c: */ /* * idetape_identify_device is called during device probing stage to * probe for an ide atapi tape drive and to initialize global variables * in ide-tape.c which provide the link between the character device * and the corresponding block device. * * Returns 1 if an ide tape was detected and is supported. * Returns 0 otherwise. */ int idetape_identify_device (ide_drive_t *drive,struct hd_driveid *id); /* * idetape_setup is called a bit later than idetape_identify_device, * during the search for disk partitions, to initialize various tape * state variables in ide_drive_t *drive. */ void idetape_setup (ide_drive_t *drive); /* * idetape_do_request is our request function. It is called by ide.c * to process a new request. */ void idetape_do_request (ide_drive_t *drive, struct request *rq, unsigned long block); /* * idetape_end_request is used to finish servicing a request, and to * insert a pending pipeline request into the main device queue. */ void idetape_end_request (byte uptodate, ide_hwgroup_t *hwgroup); /* * Block device interface functions. */ int idetape_blkdev_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg); int idetape_blkdev_open (struct inode *inode, struct file *filp, ide_drive_t *drive); void idetape_blkdev_release (struct inode *inode, struct file *filp, ide_drive_t *drive); /* * idetape_register_chrdev initializes the character device interface to * the ide tape drive. */ void idetape_register_chrdev (void); #endif /* CONFIG_BLK_DEV_IDETAPE */ #ifdef CONFIG_BLK_DEV_IDEFLOPPY int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id); void idefloppy_setup (ide_drive_t *drive); void idefloppy_do_request (ide_drive_t *drive, struct request *rq, unsigned long block); void idefloppy_end_request (byte uptodate, ide_hwgroup_t *hwgroup); int idefloppy_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg); int idefloppy_open (struct inode *inode, struct file *filp, ide_drive_t *drive); void idefloppy_release (struct inode *inode, struct file *filp, ide_drive_t *drive); int idefloppy_media_change (ide_drive_t *drive); unsigned long idefloppy_capacity (ide_drive_t *drive); #endif /* CONFIG_BLK_DEV_IDEFLOPPY */ #ifdef CONFIG_BLK_DEV_IDESCSI void idescsi_setup (ide_drive_t *drive); void idescsi_do_request (ide_drive_t *drive, struct request *rq, unsigned long block); void idescsi_end_request (byte uptodate, ide_hwgroup_t *hwgroup); int idescsi_ioctl (ide_drive_t *drive, struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg); int idescsi_open (struct inode *inode, struct file *filp, ide_drive_t *drive); void idescsi_ide_release (struct inode *inode, struct file *filp, ide_drive_t *drive); #endif /* CONFIG_BLK_DEV_IDESCSI */ #ifdef CONFIG_BLK_DEV_TRITON void ide_init_triton (byte, byte); #endif /* CONFIG_BLK_DEV_TRITON */