Subversion Repositories or1k

#
# This file is used for selecting non-standard netcard options, and
# need not be modified for typical use.
#
# Drivers are *not* selected in this file, but rather with files
# automatically generated during the top-level kernel configuration.
#
# Special options supported, indexed by their 'config' name:
#
#  CONFIG_WD80x3        The Western Digital (SMC) WD80x3 driver
#       WD_SHMEM=xxx    Forces the address of the shared memory
#  CONFIG_NE2000        The NE-[12]000 clone driver.
#       PACKETBUF_MEMSIZE  Allows an extra-large packet buffer to be
#                       used.  Usually pointless under Linux.
#       show_all_SAPROM  Show the entire address PROM, not just the
#                       ethernet address, during boot.
#       CONFIG_NE_RW_BUGFIX  Patch an obscure bug with a version of the 8390.
#       CONFIG_NE_SANITY Double check the internal card xfer address
#                       against the driver's value. Useful for debugging.
#  CONFIG_HPLAN         The HP-LAN driver (for 8390-based boards only).
#       rw_bugfix       Fix the same obscure bug.
#  CONFIG_EL2           The 3c503 EtherLink II driver
#       EL2_AUI         Default to the AUI port instead of the BNC port
#       no_probe_nonshared_memory  Don't probe for programmed-I/O boards.
#       EL2MEMTEST      Test shared memory at boot-time.
#  CONFIG_PLIP          The Crynwr-protocol PL/IP driver
#       INITIALTIMEOUTFACTOR    Timing parameters.
#       MAXTIMEOUTFACTOR
#  DE600                The D-Link DE-600 Portable Ethernet Adaptor.
#         DE600_IO      The DE600 I/O-port address (0x378 == default)
#         DE600_IRQ     The DE600 IRQ number to use (IRQ7 == default)
#         DE600_DEBUG   Enable or disable DE600 debugging (default off)
#  DE620                The D-Link DE-600 Portable Ethernet Adaptor.
#         DE620_IO      The DE620 I/O-port address (0x378 == default)
#         DE620_IRQ     The DE620 IRQ number to use (IRQ7 == default)
#         DE620_DEBUG   Enable or disable DE600 debugging (default off)
#  DEPCA                The DIGITAL series of LANCE based Ethernet Cards
#                       (DEPCA, DE100, DE200/1/2, DE210, DE422 (EISA))
#  EWRK3                The DIGITAL series of AT Ethernet Cards (DE203/4/5)
#       EWRK3_DEBUG     Set the desired debug level
#
#  DE4x5                The DIGITAL series of PCI/EISA Ethernet Cards,
#                       DE425, DE434, DE435, DE450, DE500
#     DE4X5_DEBUG       Set the desired debug level
#     DEC_ONLY          Allows driver to work with DIGITAL cards only - 
#                       see linux/drivers/net/README.de4x5
#     DE4X5_AUTOSENSE   (Default) auto media/mode selection
#                       If you want at least one board to not autosense then
#                       no board can autosense. For a board mix of several
#                       types, OR the manual values [eg for a DE500 (100M) with
#                       a DE450 (AUI) use '-DDE4X5_AUTOSENSE=(_100Mb|AUI)']
#                       For full auto media/mode selection           = AUTO
#                       For manual TP media selection                = TP
#                       For manual TP/Nway media selection (DC21041) = TP_NW
#                       For manual BNC media selection               = BNC
#                       For manual AUI media selection               = AUI
#                       For manual BNC/AUI media selection (DC21040) = BNC_AUI
#                       For manual 10Mb/s mode selection   (DC21140) = _10Mb
#                       For manual 100Mb/s mode selection  (DC21140) = _100Mb
#                       The DC21040 will default to TP if TP_NW is specified
#                       The DC21041 will default to BNC if BNC_AUI is specified
#     DE4X5_DO_MEMCPY   Forces the Intels to use memory copies into sk_buffs
#                       rather than straight DMA.
#
#  DEFXX                The DIGITAL series of FDDI EISA (DEFEA) and PCI (DEFPA)
#                       controllers
#       DEFXX_DEBUG     Set the desired debug level
#
#  TULIP                Tulip (dc21040/dc21041/ds21140) driver
#       TULIP_PORT      specify default if_port
#                       0: 10TP
#                       1: 100Tx(ds21140)/AUI(dc2104x)
#                       2: BNC(dc2104x)
#       TULIP_FIX_PORT  don't change if_port automatically if defined
#       TULIP_MAX_CARDS maximum number of probed card
#

# The following options exist, but cannot be set in this file.
#  lance.c
#       LANCE_DMA       Change the default DMA to other than DMA5.
#  8390.c
#       NO_PINGPONG     Disable ping-pong transmit buffers.


# Most drivers also have a *_DEBUG setting that may be adjusted.
# The 8390 drivers share the EI_DEBUG setting.

# General options for Space.c
OPTS            = # -DETH0_ADDR=0x300 -DETH0_IRQ=11

WD_OPTS         = #-DWD_SHMEM=0xDD000
EL2_OPTS        = #-DEL2_AUI
NE_OPTS         =
HP_OPTS         =
PLIP_OPTS       =
DEPCA_OPTS      = 
EWRK3_OPTS      = 
DE4X5_OPTS      = -DDE4X5_AUTOSENSE=AUTO
DEFXX_OPTS      =
ELP_OPTS        =
TULIP_OPTS      =
OETH_OPTS       =