URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [net/] [atarilance.c] - Rev 1777
Go to most recent revision | Compare with Previous | Blame | View Log
/* atarilance.c: Ethernet driver for VME Lance cards on the Atari */ /* Written 1995/96 by Roman Hodek (Roman.Hodek@informatik.uni-erlangen.de) This software may be used and distributed according to the terms of the GNU Public License, incorporated herein by reference. This drivers was written with the following sources of reference: - The driver for the Riebl Lance card by the TU Vienna. - The modified TUW driver for PAM's VME cards - The PC-Linux driver for Lance cards (but this is for bus master cards, not the shared memory ones) - The Amiga Ariadne driver v1.0: (in 1.2.13pl4/0.9.13) Initial version v1.1: (in 1.2.13pl5) more comments deleted some debugging stuff optimized register access (keep AREG pointing to CSR0) following AMD, CSR0_STRT should be set only after IDON is detected use memcpy() for data transfers, that also employs long word moves better probe procedure for 24-bit systems non-VME-RieblCards need extra delays in memcpy must also do write test, since 0xfxe00000 may hit ROM use 8/32 tx/rx buffers, which should give better NFS performance; this is made possible by shifting the last packet buffer after the RieblCard reserved area v1.2: (in 1.2.13pl8) again fixed probing for the Falcon; 0xfe01000 hits phys. 0x00010000 and thus RAM, in case of no Lance found all memory contents have to be restored! Now possible to compile as module. v1.3: 03/30/96 Jes Sorensen, Roman (in 1.3) Several little 1.3 adaptions When the lance is stopped it jumps back into little-endian mode. It is therefore necessary to put it back where it belongs, in big endian mode, in order to make things work. This might be the reason why multicast-mode didn't work before, but I'm not able to test it as I only got an Amiga (we had similar problems with the A2065 driver). */ static char *version = "atarilance.c: v1.3 04/04/96 " "Roman.Hodek@informatik.uni-erlangen.de\n"; #include <linux/module.h> #include <linux/stddef.h> #include <linux/kernel.h> #include <linux/sched.h> #include <linux/string.h> #include <linux/ptrace.h> #include <linux/errno.h> #include <linux/malloc.h> #include <linux/interrupt.h> #include <asm/irq.h> #include <asm/atarihw.h> #include <asm/atariints.h> #include <asm/bitops.h> #include <asm/io.h> #include <asm/bootinfo.h> #include <linux/netdevice.h> #include <linux/etherdevice.h> #include <linux/skbuff.h> /* Debug level: * 0 = silent, print only serious errors * 1 = normal, print error messages * 2 = debug, print debug infos * 3 = debug, print even more debug infos (packet data) */ #define LANCE_DEBUG 1 #ifdef LANCE_DEBUG static int lance_debug = LANCE_DEBUG; #else static int lance_debug = 1; #endif /* Print debug messages on probing? */ #undef LANCE_DEBUG_PROBE #define DPRINTK(n,a) \ do { \ if (lance_debug >= n) \ printk a; \ } while( 0 ) #ifdef LANCE_DEBUG_PROBE # define PROBE_PRINT(a) printk a #else # define PROBE_PRINT(a) #endif /* These define the number of Rx and Tx buffers as log2. (Only powers * of two are valid) * Much more rx buffers (32) are reserved than tx buffers (8), since receiving * is more time critical then sending and packets may have to remain in the * board's memory when main memory is low. */ #define TX_LOG_RING_SIZE 3 #define RX_LOG_RING_SIZE 5 /* These are the derived values */ #define TX_RING_SIZE (1 << TX_LOG_RING_SIZE) #define TX_RING_LEN_BITS (TX_LOG_RING_SIZE << 5) #define TX_RING_MOD_MASK (TX_RING_SIZE - 1) #define RX_RING_SIZE (1 << RX_LOG_RING_SIZE) #define RX_RING_LEN_BITS (RX_LOG_RING_SIZE << 5) #define RX_RING_MOD_MASK (RX_RING_SIZE - 1) /* The LANCE Rx and Tx ring descriptors. */ struct lance_rx_head { unsigned short base; /* Low word of base addr */ volatile unsigned char flag; unsigned char base_hi; /* High word of base addr (unused) */ short buf_length; /* This length is 2s complement! */ volatile short msg_length; /* This length is "normal". */ }; struct lance_tx_head { unsigned short base; /* Low word of base addr */ volatile unsigned char flag; unsigned char base_hi; /* High word of base addr (unused) */ short length; /* Length is 2s complement! */ volatile short misc; }; struct ringdesc { unsigned short adr_lo; /* Low 16 bits of address */ unsigned char len; /* Length bits */ unsigned char adr_hi; /* High 8 bits of address (unused) */ }; /* The LANCE initialization block, described in databook. */ struct lance_init_block { unsigned short mode; /* Pre-set mode */ unsigned char hwaddr[6]; /* Physical ethernet address */ unsigned filter[2]; /* Multicast filter (unused). */ /* Receive and transmit ring base, along with length bits. */ struct ringdesc rx_ring; struct ringdesc tx_ring; }; /* The whole layout of the Lance shared memory */ struct lance_memory { struct lance_init_block init; struct lance_tx_head tx_head[TX_RING_SIZE]; struct lance_rx_head rx_head[RX_RING_SIZE]; char packet_area[0]; /* packet data follow after the * init block and the ring * descriptors and are located * at runtime */ }; /* RieblCard specifics: * The original TOS driver for these cards reserves the area from offset * 0xee70 to 0xeebb for storing configuration data. Of interest to us is the * Ethernet address there, and the magic for verifying the data's validity. * The reserved area isn't touch by packet buffers. Furthermore, offset 0xfffe * is reserved for the interrupt vector number. */ #define RIEBL_RSVD_START 0xee70 #define RIEBL_RSVD_END 0xeec0 #define RIEBL_MAGIC 0x09051990 #define RIEBL_MAGIC_ADDR ((unsigned long *)(((char *)MEM) + 0xee8a)) #define RIEBL_HWADDR_ADDR ((unsigned char *)(((char *)MEM) + 0xee8e)) #define RIEBL_IVEC_ADDR ((unsigned short *)(((char *)MEM) + 0xfffe)) /* This is a default address for the old RieblCards without a battery * that have no ethernet address at boot time. 00:00:36:04 is the * prefix for Riebl cards, the 00:00 at the end is arbitrary. */ static unsigned char OldRieblDefHwaddr[6] = { 0x00, 0x00, 0x36, 0x04, 0x00, 0x00 }; /* I/O registers of the Lance chip */ struct lance_ioreg { /* base+0x0 */ volatile unsigned short data; /* base+0x2 */ volatile unsigned short addr; unsigned char _dummy1[3]; /* base+0x7 */ volatile unsigned char ivec; unsigned char _dummy2[5]; /* base+0xd */ volatile unsigned char eeprom; unsigned char _dummy3; /* base+0xf */ volatile unsigned char mem; }; /* Types of boards this driver supports */ enum lance_type { OLD_RIEBL, /* old Riebl card without battery */ NEW_RIEBL, /* new Riebl card with battery */ PAM_CARD /* PAM card with EEPROM */ }; static char *lance_names[] = { "Riebl-Card (without battery)", "Riebl-Card (with battery)", "PAM intern card" }; /* The driver's private device structure */ struct lance_private { enum lance_type cardtype; struct lance_ioreg *iobase; struct lance_memory *mem; int cur_rx, cur_tx; /* The next free ring entry */ int dirty_tx; /* Ring entries to be freed. */ /* copy function */ void *(*memcpy_f)( void *, const void *, size_t ); struct enet_statistics stats; /* These two must be ints for set_bit() */ int tx_full; int lock; }; /* I/O register access macros */ #define MEM lp->mem #define DREG IO->data #define AREG IO->addr #define REGA(a) ( AREG = (a), DREG ) /* Definitions for packet buffer access: */ #define PKT_BUF_SZ 1544 /* Get the address of a packet buffer corresponding to a given buffer head */ #define PKTBUF_ADDR(head) (((unsigned char *)(MEM)) + (head)->base) /* Possible memory/IO addresses for probing */ struct lance_addr { unsigned long memaddr; unsigned long ioaddr; int slow_flag; } lance_addr_list[] = { { 0xfe010000, 0xfe00fff0, 0 }, /* RieblCard VME in TT */ { 0xffc10000, 0xffc0fff0, 0 }, /* RieblCard VME in MegaSTE (highest byte stripped) */ { 0xffe00000, 0xffff7000, 1 }, /* RieblCard in ST (highest byte stripped) */ { 0xffd00000, 0xffff7000, 1 }, /* RieblCard in ST with hw modif. to avoid conflict with ROM (highest byte stripped) */ { 0xffcf0000, 0xffcffff0, 0 }, /* PAMCard VME in TT and MSTE (highest byte stripped) */ }; #define N_LANCE_ADDR (sizeof(lance_addr_list)/sizeof(*lance_addr_list)) /* Definitions for the Lance */ /* tx_head flags */ #define TMD1_ENP 0x01 /* end of packet */ #define TMD1_STP 0x02 /* start of packet */ #define TMD1_DEF 0x04 /* deferred */ #define TMD1_ONE 0x08 /* one retry needed */ #define TMD1_MORE 0x10 /* more than one retry needed */ #define TMD1_ERR 0x40 /* error summary */ #define TMD1_OWN 0x80 /* ownership (set: chip owns) */ #define TMD1_OWN_CHIP TMD1_OWN #define TMD1_OWN_HOST 0 /* tx_head misc field */ #define TMD3_TDR 0x03FF /* Time Domain Reflectometry counter */ #define TMD3_RTRY 0x0400 /* failed after 16 retries */ #define TMD3_LCAR 0x0800 /* carrier lost */ #define TMD3_LCOL 0x1000 /* late collision */ #define TMD3_UFLO 0x4000 /* underflow (late memory) */ #define TMD3_BUFF 0x8000 /* buffering error (no ENP) */ /* rx_head flags */ #define RMD1_ENP 0x01 /* end of packet */ #define RMD1_STP 0x02 /* start of packet */ #define RMD1_BUFF 0x04 /* buffer error */ #define RMD1_CRC 0x08 /* CRC error */ #define RMD1_OFLO 0x10 /* overflow */ #define RMD1_FRAM 0x20 /* framing error */ #define RMD1_ERR 0x40 /* error summary */ #define RMD1_OWN 0x80 /* ownership (set: ship owns) */ #define RMD1_OWN_CHIP RMD1_OWN #define RMD1_OWN_HOST 0 /* register names */ #define CSR0 0 /* mode/status */ #define CSR1 1 /* init block addr (low) */ #define CSR2 2 /* init block addr (high) */ #define CSR3 3 /* misc */ #define CSR8 8 /* address filter */ #define CSR15 15 /* promiscuous mode */ /* CSR0 */ /* (R=readable, W=writeable, S=set on write, C=clear on write) */ #define CSR0_INIT 0x0001 /* initialize (RS) */ #define CSR0_STRT 0x0002 /* start (RS) */ #define CSR0_STOP 0x0004 /* stop (RS) */ #define CSR0_TDMD 0x0008 /* transmit demand (RS) */ #define CSR0_TXON 0x0010 /* transmitter on (R) */ #define CSR0_RXON 0x0020 /* receiver on (R) */ #define CSR0_INEA 0x0040 /* interrupt enable (RW) */ #define CSR0_INTR 0x0080 /* interrupt active (R) */ #define CSR0_IDON 0x0100 /* initialization done (RC) */ #define CSR0_TINT 0x0200 /* transmitter interrupt (RC) */ #define CSR0_RINT 0x0400 /* receiver interrupt (RC) */ #define CSR0_MERR 0x0800 /* memory error (RC) */ #define CSR0_MISS 0x1000 /* missed frame (RC) */ #define CSR0_CERR 0x2000 /* carrier error (no heartbeat :-) (RC) */ #define CSR0_BABL 0x4000 /* babble: tx-ed too many bits (RC) */ #define CSR0_ERR 0x8000 /* error (RC) */ /* CSR3 */ #define CSR3_BCON 0x0001 /* byte control */ #define CSR3_ACON 0x0002 /* ALE control */ #define CSR3_BSWP 0x0004 /* byte swap (1=big endian) */ /***************************** Prototypes *****************************/ static int addr_accessible( volatile void *regp, int wordflag, int writeflag ); static unsigned long lance_probe1( struct device *dev, struct lance_addr *init_rec ); static int lance_open( struct device *dev ); static void lance_init_ring( struct device *dev ); static int lance_start_xmit( struct sk_buff *skb, struct device *dev ); static void lance_interrupt( int irq, struct pt_regs *fp, struct device *dev ); static int lance_rx( struct device *dev ); static int lance_close( struct device *dev ); static struct enet_statistics *lance_get_stats( struct device *dev ); static void set_multicast_list( struct device *dev ); static int lance_set_mac_address( struct device *dev, void *addr ); /************************* End of Prototypes **************************/ void *slow_memcpy( void *dst, const void *src, size_t len ) { char *cto = dst; const char *cfrom = src; while( len-- ) { *cto++ = *cfrom++; MFPDELAY(); } return( dst ); } int atarilance_probe( struct device *dev ) { int i; static int found = 0; if (!MACH_IS_ATARI || found) /* Assume there's only one board possible... That seems true, since * the Riebl/PAM board's address cannot be changed. */ return( ENODEV ); for( i = 0; i < N_LANCE_ADDR; ++i ) { if (lance_probe1( dev, &lance_addr_list[i] )) { found = 1; return( 0 ); } } return( ENODEV ); } /* Derived from hwreg_present() in atari/config.c: */ static int addr_accessible( volatile void *regp, int wordflag, int writeflag ) { int ret; long flags; long *vbr, save_berr; save_flags(flags); cli(); __asm__ __volatile__ ( "movec %/vbr,%0" : "=r" (vbr) : ); save_berr = vbr[2]; __asm__ __volatile__ ( "movel %/sp,%/d1\n\t" "movel #Lberr,%2@\n\t" "moveq #0,%0\n\t" "tstl %3\n\t" "bne 1f\n\t" "moveb %1@,%/d0\n\t" "nop \n\t" "bra 2f\n" "1: movew %1@,%/d0\n\t" "nop \n" "2: tstl %4\n\t" "beq 2f\n\t" "tstl %3\n\t" "bne 1f\n\t" "clrb %1@\n\t" "nop \n\t" "moveb %/d0,%1@\n\t" "nop \n\t" "bra 2f\n" "1: clrw %1@\n\t" "nop \n\t" "movew %/d0,%1@\n\t" "nop \n" "2: moveq #1,%0\n" "Lberr: movel %/d1,%/sp" : "=&d" (ret) : "a" (regp), "a" (&vbr[2]), "rm" (wordflag), "rm" (writeflag) : "d0", "d1", "memory" ); vbr[2] = save_berr; restore_flags(flags); return( ret ); } static unsigned long lance_probe1( struct device *dev, struct lance_addr *init_rec ) { volatile unsigned short *memaddr = (volatile unsigned short *)init_rec->memaddr; volatile unsigned short *ioaddr = (volatile unsigned short *)init_rec->ioaddr; struct lance_private *lp; struct lance_ioreg *IO; int i; static int did_version = 0; unsigned short save1, save2; PROBE_PRINT(( "Probing for Lance card at mem %#lx io %#lx\n", (long)memaddr, (long)ioaddr )); /* Test whether memory readable and writable */ PROBE_PRINT(( "lance_probe1: testing memory to be accessible\n" )); if (!addr_accessible( memaddr, 1, 1 )) goto probe_fail; /* Written values should come back... */ PROBE_PRINT(( "lance_probe1: testing memory to be writable (1)\n" )); save1 = *memaddr; *memaddr = 0x0001; if (*memaddr != 0x0001) goto probe_fail; PROBE_PRINT(( "lance_probe1: testing memory to be writable (2)\n" )); *memaddr = 0x0000; if (*memaddr != 0x0000) goto probe_fail; *memaddr = save1; /* First port should be readable and writable */ PROBE_PRINT(( "lance_probe1: testing ioport to be accessible\n" )); if (!addr_accessible( ioaddr, 1, 1 )) goto probe_fail; /* and written values should be readable */ PROBE_PRINT(( "lance_probe1: testing ioport to be writeable\n" )); save2 = ioaddr[1]; ioaddr[1] = 0x0001; if (ioaddr[1] != 0x0001) goto probe_fail; /* The CSR0_INIT bit should not be readable */ PROBE_PRINT(( "lance_probe1: testing CSR0 register function (1)\n" )); save1 = ioaddr[0]; ioaddr[1] = CSR0; ioaddr[0] = CSR0_INIT | CSR0_STOP; if (ioaddr[0] != CSR0_STOP) { ioaddr[0] = save1; ioaddr[1] = save2; goto probe_fail; } PROBE_PRINT(( "lance_probe1: testing CSR0 register function (2)\n" )); ioaddr[0] = CSR0_STOP; if (ioaddr[0] != CSR0_STOP) { ioaddr[0] = save1; ioaddr[1] = save2; goto probe_fail; } /* Now ok... */ PROBE_PRINT(( "lance_probe1: Lance card detected\n" )); goto probe_ok; probe_fail: return( 0 ); probe_ok: init_etherdev( dev, sizeof(struct lance_private) ); if (!dev->priv) dev->priv = kmalloc( sizeof(struct lance_private), GFP_KERNEL ); lp = (struct lance_private *)dev->priv; MEM = (struct lance_memory *)memaddr; IO = lp->iobase = (struct lance_ioreg *)ioaddr; dev->base_addr = (unsigned long)ioaddr; /* informational only */ lp->memcpy_f = init_rec->slow_flag ? slow_memcpy : memcpy; REGA( CSR0 ) = CSR0_STOP; /* Now test for type: If the eeprom I/O port is readable, it is a * PAM card */ if (addr_accessible( &(IO->eeprom), 0, 0 )) { /* Switch back to Ram */ i = IO->mem; lp->cardtype = PAM_CARD; } else if (*RIEBL_MAGIC_ADDR == RIEBL_MAGIC) { lp->cardtype = NEW_RIEBL; } else lp->cardtype = OLD_RIEBL; if (lp->cardtype == PAM_CARD || memaddr == (unsigned short *)0xffe00000) { /* PAMs card and Riebl on ST use level 5 autovector */ add_isr( IRQ_AUTO_5, (isrfunc)lance_interrupt, IRQ_TYPE_PRIO, dev, "PAM/Riebl-ST Ethernet" ); dev->irq = (unsigned short)IRQ_AUTO_5; } else { /* For VME-RieblCards, request a free VME int; * (This must be unsigned long, since dev->irq is short and the * IRQ_MACHSPEC bit would be cut off...) */ unsigned long irq = atari_register_vme_int(); if (!irq) { printk( "Lance: request for VME interrupt failed\n" ); return( 0 ); } add_isr( irq, (isrfunc)lance_interrupt, IRQ_TYPE_PRIO, dev, "Riebl-VME Ethernet" ); dev->irq = irq; } printk("%s: %s at io %#lx, mem %#lx, irq %d%s, hwaddr ", dev->name, lance_names[lp->cardtype], (unsigned long)ioaddr, (unsigned long)memaddr, dev->irq, init_rec->slow_flag ? " (slow memcpy)" : "" ); /* Get the ethernet address */ switch( lp->cardtype ) { case OLD_RIEBL: /* No ethernet address! (Set some default address) */ memcpy( dev->dev_addr, OldRieblDefHwaddr, 6 ); break; case NEW_RIEBL: lp->memcpy_f( dev->dev_addr, RIEBL_HWADDR_ADDR, 6 ); break; case PAM_CARD: i = IO->eeprom; for( i = 0; i < 6; ++i ) dev->dev_addr[i] = ((((unsigned short *)MEM)[i*2] & 0x0f) << 4) | ((((unsigned short *)MEM)[i*2+1] & 0x0f)); i = IO->mem; break; } for( i = 0; i < 6; ++i ) printk( "%02x%s", dev->dev_addr[i], (i < 5) ? ":" : "\n" ); if (lp->cardtype == OLD_RIEBL) { printk( "%s: Warning: This is a default ethernet address!\n", dev->name ); printk( " Use \"ifconfig hw ether ...\" to set the address.\n" ); } MEM->init.mode = 0x0000; /* Disable Rx and Tx. */ for( i = 0; i < 6; i++ ) MEM->init.hwaddr[i] = dev->dev_addr[i^1]; /* <- 16 bit swap! */ MEM->init.filter[0] = 0x00000000; MEM->init.filter[1] = 0x00000000; MEM->init.rx_ring.adr_lo = offsetof( struct lance_memory, rx_head ); MEM->init.rx_ring.adr_hi = 0; MEM->init.rx_ring.len = RX_RING_LEN_BITS; MEM->init.tx_ring.adr_lo = offsetof( struct lance_memory, tx_head ); MEM->init.tx_ring.adr_hi = 0; MEM->init.tx_ring.len = TX_RING_LEN_BITS; if (lp->cardtype == PAM_CARD) IO->ivec = IRQ_SOURCE_TO_VECTOR(dev->irq); else *RIEBL_IVEC_ADDR = IRQ_SOURCE_TO_VECTOR(dev->irq); if (did_version++ == 0) DPRINTK( 1, ( version )); /* The LANCE-specific entries in the device structure. */ dev->open = &lance_open; dev->hard_start_xmit = &lance_start_xmit; dev->stop = &lance_close; dev->get_stats = &lance_get_stats; dev->set_multicast_list = &set_multicast_list; dev->set_mac_address = &lance_set_mac_address; dev->start = 0; memset( &lp->stats, 0, sizeof(lp->stats) ); return( 1 ); } static int lance_open( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; struct lance_ioreg *IO = lp->iobase; int i; DPRINTK( 2, ( "%s: lance_open()\n", dev->name )); lance_init_ring(dev); /* Re-initialize the LANCE, and start it when done. */ REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0); REGA( CSR2 ) = 0; REGA( CSR1 ) = 0; REGA( CSR0 ) = CSR0_INIT; /* From now on, AREG is kept to point to CSR0 */ i = 1000000; while (--i > 0) if (DREG & CSR0_IDON) break; if (i < 0 || (DREG & CSR0_ERR)) { DPRINTK( 2, ( "lance_open(): opening %s failed, i=%d, csr0=%04x\n", dev->name, i, DREG )); DREG = CSR0_STOP; return( -EIO ); } DREG = CSR0_IDON; DREG = CSR0_STRT; DREG = CSR0_INEA; dev->tbusy = 0; dev->interrupt = 0; dev->start = 1; DPRINTK( 2, ( "%s: LANCE is open, csr0 %04x\n", dev->name, DREG )); MOD_INC_USE_COUNT; return( 0 ); } /* Initialize the LANCE Rx and Tx rings. */ static void lance_init_ring( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; int i; unsigned offset; lp->lock = 0; lp->tx_full = 0; lp->cur_rx = lp->cur_tx = 0; lp->dirty_tx = 0; offset = offsetof( struct lance_memory, packet_area ); /* If the packet buffer at offset 'o' would conflict with the reserved area * of RieblCards, advance it */ #define CHECK_OFFSET(o) \ do { \ if (lp->cardtype == OLD_RIEBL || lp->cardtype == NEW_RIEBL) { \ if (((o) < RIEBL_RSVD_START) ? (o)+PKT_BUF_SZ > RIEBL_RSVD_START \ : (o) < RIEBL_RSVD_END) \ (o) = RIEBL_RSVD_END; \ } \ } while(0) for( i = 0; i < TX_RING_SIZE; i++ ) { CHECK_OFFSET(offset); MEM->tx_head[i].base = offset; MEM->tx_head[i].flag = TMD1_OWN_HOST; MEM->tx_head[i].base_hi = 0; MEM->tx_head[i].length = 0; MEM->tx_head[i].misc = 0; offset += PKT_BUF_SZ; } for( i = 0; i < RX_RING_SIZE; i++ ) { CHECK_OFFSET(offset); MEM->rx_head[i].base = offset; MEM->rx_head[i].flag = TMD1_OWN_CHIP; MEM->rx_head[i].base_hi = 0; MEM->rx_head[i].buf_length = -PKT_BUF_SZ; MEM->rx_head[i].msg_length = 0; offset += PKT_BUF_SZ; } } static int lance_start_xmit( struct sk_buff *skb, struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; struct lance_ioreg *IO = lp->iobase; int entry, len; struct lance_tx_head *head; unsigned long flags; /* Transmitter timeout, serious problems. */ if (dev->tbusy) { int tickssofar = jiffies - dev->trans_start; if (tickssofar < 20) return( 1 ); AREG = CSR0; DPRINTK( 1, ( "%s: transmit timed out, status %04x, resetting.\n", dev->name, DREG )); DREG = CSR0_STOP; /* * Always set BSWP after a STOP as STOP puts it back into * little endian mode. */ REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0); lp->stats.tx_errors++; #ifndef final_version { int i; DPRINTK( 2, ( "Ring data: dirty_tx %d cur_tx %d%s cur_rx %d\n", lp->dirty_tx, lp->cur_tx, lp->tx_full ? " (full)" : "", lp->cur_rx )); for( i = 0 ; i < RX_RING_SIZE; i++ ) DPRINTK( 2, ( "rx #%d: base=%04x blen=%04x mlen=%04x\n", i, MEM->rx_head[i].base, -MEM->rx_head[i].buf_length, MEM->rx_head[i].msg_length )); for( i = 0 ; i < TX_RING_SIZE; i++ ) DPRINTK( 2, ( "tx #%d: base=%04x len=%04x misc=%04x\n", i, MEM->tx_head[i].base, -MEM->tx_head[i].length, MEM->tx_head[i].misc )); } #endif lance_init_ring(dev); REGA( CSR0 ) = CSR0_INEA | CSR0_INIT | CSR0_STRT; dev->tbusy = 0; dev->trans_start = jiffies; dev_kfree_skb(skb, FREE_WRITE); return( 0 ); } if (skb == NULL) { dev_tint( dev ); return( 0 ); } if (skb->len <= 0) return( 0 ); DPRINTK( 2, ( "%s: lance_start_xmit() called, csr0 %4.4x.\n", dev->name, DREG )); /* Block a timer-based transmit from overlapping. This could better be done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */ if (set_bit( 0, (void*)&dev->tbusy ) != 0) { DPRINTK( 0, ( "%s: Transmitter access conflict.\n", dev->name )); return 1; } if (set_bit( 0, (void*)&lp->lock ) != 0) { DPRINTK( 0, ( "%s: tx queue lock!.\n", dev->name )); /* don't clear dev->tbusy flag. */ return 1; } /* Fill in a Tx ring entry */ if (lance_debug >= 3) { u_char *p; int i; printk( "%s: TX pkt type 0x%04x from ", dev->name, ((u_short *)skb->data)[6]); for( p = &((u_char *)skb->data)[6], i = 0; i < 6; i++ ) printk("%02x%s", *p++, i != 5 ? ":" : "" ); printk(" to "); for( p = (u_char *)skb->data, i = 0; i < 6; i++ ) printk("%02x%s", *p++, i != 5 ? ":" : "" ); printk(" data at 0x%08x len %d\n", (int)skb->data, (int)skb->len ); } /* We're not prepared for the int until the last flags are set/reset. And * the int may happen already after setting the OWN_CHIP... */ save_flags(flags); cli(); /* Mask to ring buffer boundary. */ entry = lp->cur_tx & TX_RING_MOD_MASK; head = &(MEM->tx_head[entry]); /* Caution: the write order is important here, set the "ownership" bits * last. */ /* The old LANCE chips doesn't automatically pad buffers to min. size. */ len = (ETH_ZLEN < skb->len) ? skb->len : ETH_ZLEN; /* PAM-Card has a bug: Can only send packets with even number of bytes! */ if (lp->cardtype == PAM_CARD && (len & 1)) ++len; head->length = -len; head->misc = 0; lp->memcpy_f( PKTBUF_ADDR(head), (void *)skb->data, skb->len ); head->flag = TMD1_OWN_CHIP | TMD1_ENP | TMD1_STP; dev_kfree_skb( skb, FREE_WRITE ); lp->cur_tx++; while( lp->cur_tx >= TX_RING_SIZE && lp->dirty_tx >= TX_RING_SIZE ) { lp->cur_tx -= TX_RING_SIZE; lp->dirty_tx -= TX_RING_SIZE; } /* Trigger an immediate send poll. */ DREG = CSR0_INEA | CSR0_TDMD; dev->trans_start = jiffies; lp->lock = 0; if ((MEM->tx_head[(entry+1) & TX_RING_MOD_MASK].flag & TMD1_OWN) == TMD1_OWN_HOST) dev->tbusy = 0; else lp->tx_full = 1; restore_flags(flags); return 0; } /* The LANCE interrupt handler. */ static void lance_interrupt( int irq, struct pt_regs *fp, struct device *dev ) { struct lance_private *lp; struct lance_ioreg *IO; int csr0, boguscnt = 10; if (dev == NULL) { DPRINTK( 1, ( "lance_interrupt(): interrupt for unknown device.\n" )); return; } lp = (struct lance_private *)dev->priv; IO = lp->iobase; AREG = CSR0; if (dev->interrupt) DPRINTK( 2, ( "%s: Re-entering the interrupt handler.\n", dev->name )); dev->interrupt = 1; while( ((csr0 = DREG) & (CSR0_ERR | CSR0_TINT | CSR0_RINT)) && --boguscnt >= 0) { /* Acknowledge all of the current interrupt sources ASAP. */ DREG = csr0 & ~(CSR0_INIT | CSR0_STRT | CSR0_STOP | CSR0_TDMD | CSR0_INEA); DPRINTK( 2, ( "%s: interrupt csr0=%04x new csr=%04x.\n", dev->name, csr0, DREG )); if (csr0 & CSR0_RINT) /* Rx interrupt */ lance_rx( dev ); if (csr0 & CSR0_TINT) { /* Tx-done interrupt */ int dirty_tx = lp->dirty_tx; while( dirty_tx < lp->cur_tx) { int entry = dirty_tx & TX_RING_MOD_MASK; int status = MEM->tx_head[entry].flag; if (status & TMD1_OWN_CHIP) break; /* It still hasn't been Txed */ MEM->tx_head[entry].flag = 0; if (status & TMD1_ERR) { /* There was an major error, log it. */ int err_status = MEM->tx_head[entry].misc; lp->stats.tx_errors++; if (err_status & TMD3_RTRY) lp->stats.tx_aborted_errors++; if (err_status & TMD3_LCAR) lp->stats.tx_carrier_errors++; if (err_status & TMD3_LCOL) lp->stats.tx_window_errors++; if (err_status & TMD3_UFLO) { /* Ackk! On FIFO errors the Tx unit is turned off! */ lp->stats.tx_fifo_errors++; /* Remove this verbosity later! */ DPRINTK( 1, ( "%s: Tx FIFO error! Status %04x\n", dev->name, csr0 )); /* Restart the chip. */ DREG = CSR0_STRT; } } else { if (status & (TMD1_MORE | TMD1_ONE | TMD1_DEF)) lp->stats.collisions++; lp->stats.tx_packets++; } dirty_tx++; } #ifndef final_version if (lp->cur_tx - dirty_tx >= TX_RING_SIZE) { DPRINTK( 0, ( "out-of-sync dirty pointer," " %d vs. %d, full=%d.\n", dirty_tx, lp->cur_tx, lp->tx_full )); dirty_tx += TX_RING_SIZE; } #endif if (lp->tx_full && dev->tbusy && dirty_tx > lp->cur_tx - TX_RING_SIZE + 2) { /* The ring is no longer full, clear tbusy. */ lp->tx_full = 0; dev->tbusy = 0; mark_bh( NET_BH ); } lp->dirty_tx = dirty_tx; } /* Log misc errors. */ if (csr0 & CSR0_BABL) lp->stats.tx_errors++; /* Tx babble. */ if (csr0 & CSR0_MISS) lp->stats.rx_errors++; /* Missed a Rx frame. */ if (csr0 & CSR0_MERR) { DPRINTK( 1, ( "%s: Bus master arbitration failure (?!?), " "status %04x.\n", dev->name, csr0 )); /* Restart the chip. */ DREG = CSR0_STRT; } } /* Clear any other interrupt, and set interrupt enable. */ DREG = CSR0_BABL | CSR0_CERR | CSR0_MISS | CSR0_MERR | CSR0_IDON | CSR0_INEA; DPRINTK( 2, ( "%s: exiting interrupt, csr0=%#04x.\n", dev->name, DREG )); dev->interrupt = 0; return; } static int lance_rx( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; int entry = lp->cur_rx & RX_RING_MOD_MASK; int i; DPRINTK( 2, ( "%s: rx int, flag=%04x\n", dev->name, MEM->rx_head[entry].flag )); /* If we own the next entry, it's a new packet. Send it up. */ while( (MEM->rx_head[entry].flag & RMD1_OWN) == RMD1_OWN_HOST ) { struct lance_rx_head *head = &(MEM->rx_head[entry]); int status = head->flag; if (status != (RMD1_ENP|RMD1_STP)) { /* There was an error. */ /* There is a tricky error noted by John Murphy, <murf@perftech.com> to Russ Nelson: Even with full-sized buffers it's possible for a jabber packet to use two buffers, with only the last correctly noting the error. */ if (status & RMD1_ENP) /* Only count a general error at the */ lp->stats.rx_errors++; /* end of a packet.*/ if (status & RMD1_FRAM) lp->stats.rx_frame_errors++; if (status & RMD1_OFLO) lp->stats.rx_over_errors++; if (status & RMD1_CRC) lp->stats.rx_crc_errors++; if (status & RMD1_BUFF) lp->stats.rx_fifo_errors++; head->flag &= (RMD1_ENP|RMD1_STP); } else { /* Malloc up new buffer, compatible with net-3. */ short pkt_len = head->msg_length & 0xfff; struct sk_buff *skb; if (pkt_len < 60) { printk( "%s: Runt packet!\n", dev->name ); lp->stats.rx_errors++; } else { skb = dev_alloc_skb( pkt_len+2 ); if (skb == NULL) { DPRINTK( 1, ( "%s: Memory squeeze, deferring packet.\n", dev->name )); for( i = 0; i < RX_RING_SIZE; i++ ) if (MEM->rx_head[(entry+i) & RX_RING_MOD_MASK].flag & RMD1_OWN_CHIP) break; if (i > RX_RING_SIZE - 2) { lp->stats.rx_dropped++; head->flag |= RMD1_OWN_CHIP; lp->cur_rx++; } break; } if (lance_debug >= 3) { u_char *data = PKTBUF_ADDR(head), *p; printk( "%s: RX pkt type 0x%04x from ", dev->name, ((u_short *)data)[6]); for( p = &data[6], i = 0; i < 6; i++ ) printk("%02x%s", *p++, i != 5 ? ":" : "" ); printk(" to "); for( p = data, i = 0; i < 6; i++ ) printk("%02x%s", *p++, i != 5 ? ":" : "" ); printk(" data %02x %02x %02x %02x %02x %02x %02x %02x " "len %d\n", data[15], data[16], data[17], data[18], data[19], data[20], data[21], data[22], pkt_len ); } skb->dev = dev; skb_reserve( skb, 2 ); /* 16 byte align */ skb_put( skb, pkt_len ); /* Make room */ lp->memcpy_f( skb->data, PKTBUF_ADDR(head), pkt_len ); skb->protocol = eth_type_trans( skb, dev ); netif_rx( skb ); lp->stats.rx_packets++; } } head->flag |= RMD1_OWN_CHIP; entry = (++lp->cur_rx) & RX_RING_MOD_MASK; } lp->cur_rx &= RX_RING_MOD_MASK; /* From lance.c (Donald Becker): */ /* We should check that at least two ring entries are free. If not, we should free one and mark stats->rx_dropped++. */ return 0; } static int lance_close( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; struct lance_ioreg *IO = lp->iobase; dev->start = 0; dev->tbusy = 1; AREG = CSR0; DPRINTK( 2, ( "%s: Shutting down ethercard, status was %2.2x.\n", dev->name, DREG )); /* We stop the LANCE here -- it occasionally polls memory if we don't. */ DREG = CSR0_STOP; MOD_DEC_USE_COUNT; return 0; } static struct enet_statistics *lance_get_stats( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; return &lp->stats; } /* Set or clear the multicast filter for this adaptor. num_addrs == -1 Promiscuous mode, receive all packets num_addrs == 0 Normal mode, clear multicast list num_addrs > 0 Multicast mode, receive normal and MC packets, and do best-effort filtering. */ static void set_multicast_list( struct device *dev ) { struct lance_private *lp = (struct lance_private *)dev->priv; struct lance_ioreg *IO = lp->iobase; if (!dev->start) /* Only possible if board is already started */ return; /* We take the simple way out and always enable promiscuous mode. */ DREG = CSR0_STOP; /* Temporarily stop the lance. */ if (dev->flags & IFF_PROMISC) { /* Log any net taps. */ DPRINTK( 1, ( "%s: Promiscuous mode enabled.\n", dev->name )); REGA( CSR15 ) = 0x8000; /* Set promiscuous mode */ } else { short multicast_table[4]; int num_addrs = dev->mc_count; int i; /* We don't use the multicast table, but rely on upper-layer * filtering. */ memset( multicast_table, (num_addrs == 0) ? 0 : -1, sizeof(multicast_table) ); for( i = 0; i < 4; i++ ) REGA( CSR8+i ) = multicast_table[i]; REGA( CSR15 ) = 0; /* Unset promiscuous mode */ } /* * Always set BSWP after a STOP as STOP puts it back into * little endian mode. */ REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0); /* Resume normal operation and reset AREG to CSR0 */ REGA( CSR0 ) = CSR0_IDON | CSR0_INEA | CSR0_STRT; } /* This is needed for old RieblCards and possible for new RieblCards */ static int lance_set_mac_address( struct device *dev, void *addr ) { struct lance_private *lp = (struct lance_private *)dev->priv; struct sockaddr *saddr = addr; int i; if (lp->cardtype != OLD_RIEBL && lp->cardtype != NEW_RIEBL) return( -EOPNOTSUPP ); if (dev->start) { /* Only possible while card isn't started */ DPRINTK( 1, ( "%s: hwaddr can be set only while card isn't open.\n", dev->name )); return( -EIO ); } memcpy( dev->dev_addr, saddr->sa_data, dev->addr_len ); for( i = 0; i < 6; i++ ) MEM->init.hwaddr[i] = dev->dev_addr[i^1]; /* <- 16 bit swap! */ lp->memcpy_f( RIEBL_HWADDR_ADDR, dev->dev_addr, 6 ); /* set also the magic for future sessions */ *RIEBL_MAGIC_ADDR = RIEBL_MAGIC; return( 0 ); } #ifdef MODULE static char devicename[9] = { 0, }; static struct device atarilance_dev = { devicename, /* filled in by register_netdev() */ 0, 0, 0, 0, /* memory */ 0, 0, /* base, irq */ 0, 0, 0, NULL, atarilance_probe, }; int init_module(void) { int err; if ((err = register_netdev( &atarilance_dev ))) { if (err == -EIO) { printk( "No Atari Lance board found. Module not loaded.\n"); } return( err ); } return( 0 ); } void cleanup_module(void) { unregister_netdev( &atarilance_dev ); } #endif /* MODULE */ /* * Local variables: * c-indent-level: 4 * tab-width: 4 * End: */
Go to most recent revision | Compare with Previous | Blame | View Log