URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [net/] [hp.c] - Rev 1765
Compare with Previous | Blame | View Log
/* hp.c: A HP LAN ethernet driver for linux. */ /* Written 1993-94 by Donald Becker. Copyright 1993 United States Government as represented by the Director, National Security Agency. This software may be used and distributed according to the terms of the GNU Public License, incorporated herein by reference. The author may be reached as becker@CESDIS.gsfc.nasa.gov, or C/O Center of Excellence in Space Data and Information Sciences Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771 This is a driver for the HP PC-LAN adaptors. Sources: The Crynwr packet driver. */ static const char *version = "hp.c:v1.10 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n"; #include <linux/module.h> #include <linux/kernel.h> #include <linux/sched.h> #include <linux/errno.h> #include <linux/ioport.h> #include <linux/netdevice.h> #include <linux/etherdevice.h> #include <asm/system.h> #include <asm/io.h> #include "8390.h" /* A zero-terminated list of I/O addresses to be probed. */ static unsigned int hppclan_portlist[] = { 0x300, 0x320, 0x340, 0x280, 0x2C0, 0x200, 0x240, 0}; #define HP_IO_EXTENT 32 #define HP_DATAPORT 0x0c /* "Remote DMA" data port. */ #define HP_ID 0x07 #define HP_CONFIGURE 0x08 /* Configuration register. */ #define HP_RUN 0x01 /* 1 == Run, 0 == reset. */ #define HP_IRQ 0x0E /* Mask for software-configured IRQ line. */ #define HP_DATAON 0x10 /* Turn on dataport */ #define NIC_OFFSET 0x10 /* Offset the 8390 registers. */ #define HP_START_PG 0x00 /* First page of TX buffer */ #define HP_8BSTOP_PG 0x80 /* Last page +1 of RX ring */ #define HP_16BSTOP_PG 0xFF /* Same, for 16 bit cards. */ int hp_probe(struct device *dev); int hp_probe1(struct device *dev, int ioaddr); static int hp_open(struct device *dev); static int hp_close(struct device *dev); static void hp_reset_8390(struct device *dev); static void hp_get_8390_hdr(struct device *dev, struct e8390_pkt_hdr *hdr, int ring_page); static void hp_block_input(struct device *dev, int count, struct sk_buff *skb , int ring_offset); static void hp_block_output(struct device *dev, int count, const unsigned char *buf, const int start_page); static void hp_init_card(struct device *dev); /* The map from IRQ number to HP_CONFIGURE register setting. */ /* My default is IRQ5 0 1 2 3 4 5 6 7 8 9 10 11 */ static char irqmap[16] = { 0, 0, 4, 6, 8,10, 0,14, 0, 4, 2,12,0,0,0,0}; /* Probe for an HP LAN adaptor. Also initialize the card and fill in STATION_ADDR with the station address. */ #ifdef HAVE_DEVLIST struct netdev_entry netcard_drv = {"hp", hp_probe1, HP_IO_EXTENT, hppclan_portlist}; #else int hp_probe(struct device *dev) { int i; int base_addr = dev ? dev->base_addr : 0; if (base_addr > 0x1ff) /* Check a single specified location. */ return hp_probe1(dev, base_addr); else if (base_addr != 0) /* Don't probe at all. */ return ENXIO; for (i = 0; hppclan_portlist[i]; i++) { int ioaddr = hppclan_portlist[i]; if (check_region(ioaddr, HP_IO_EXTENT)) continue; if (hp_probe1(dev, ioaddr) == 0) return 0; } return ENODEV; } #endif int hp_probe1(struct device *dev, int ioaddr) { int i, board_id, wordmode; const char *name; static unsigned version_printed = 0; /* Check for the HP physical address, 08 00 09 xx xx xx. */ /* This really isn't good enough: we may pick up HP LANCE boards also! Avoid the lance 0x5757 signature. */ if (inb(ioaddr) != 0x08 || inb(ioaddr+1) != 0x00 || inb(ioaddr+2) != 0x09 || inb(ioaddr+14) == 0x57) return ENODEV; /* Set up the parameters based on the board ID. If you have additional mappings, please mail them to me -djb. */ if ((board_id = inb(ioaddr + HP_ID)) & 0x80) { name = "HP27247"; wordmode = 1; } else { name = "HP27250"; wordmode = 0; } /* We should have a "dev" from Space.c or the static module table. */ if (dev == NULL) { printk("hp.c: Passed a NULL device.\n"); dev = init_etherdev(0, 0); } if (ei_debug && version_printed++ == 0) printk(version); printk("%s: %s (ID %02x) at %#3x,", dev->name, name, board_id, ioaddr); for(i = 0; i < ETHER_ADDR_LEN; i++) printk(" %2.2x", dev->dev_addr[i] = inb(ioaddr + i)); /* Snarf the interrupt now. Someday this could be moved to open(). */ if (dev->irq < 2) { int irq_16list[] = { 11, 10, 5, 3, 4, 7, 9, 0}; int irq_8list[] = { 7, 5, 3, 4, 9, 0}; int *irqp = wordmode ? irq_16list : irq_8list; do { int irq = *irqp; if (request_irq (irq, NULL, 0, "bogus", NULL) != -EBUSY) { autoirq_setup(0); /* Twinkle the interrupt, and check if it's seen. */ outb_p(irqmap[irq] | HP_RUN, ioaddr + HP_CONFIGURE); outb_p( 0x00 | HP_RUN, ioaddr + HP_CONFIGURE); if (irq == autoirq_report(0) /* It's a good IRQ line! */ && request_irq (irq, &ei_interrupt, 0, "hp", NULL) == 0) { printk(" selecting IRQ %d.\n", irq); dev->irq = *irqp; break; } } } while (*++irqp); if (*irqp == 0) { printk(" no free IRQ lines.\n"); return EBUSY; } } else { if (dev->irq == 2) dev->irq = 9; if (request_irq(dev->irq, ei_interrupt, 0, "hp", NULL)) { printk (" unable to get IRQ %d.\n", dev->irq); return EBUSY; } } /* Allocate dev->priv and fill in 8390 specific dev fields. */ if (ethdev_init(dev)) { printk (" unable to get memory for dev->priv.\n"); free_irq(dev->irq, NULL); return -ENOMEM; } /* Grab the region so we can find another board if something fails. */ request_region(ioaddr, HP_IO_EXTENT,"hp"); /* Set the base address to point to the NIC, not the "real" base! */ dev->base_addr = ioaddr + NIC_OFFSET; dev->open = &hp_open; dev->stop = &hp_close; ei_status.name = name; ei_status.word16 = wordmode; ei_status.tx_start_page = HP_START_PG; ei_status.rx_start_page = HP_START_PG + TX_PAGES; ei_status.stop_page = wordmode ? HP_16BSTOP_PG : HP_8BSTOP_PG; ei_status.reset_8390 = &hp_reset_8390; ei_status.get_8390_hdr = &hp_get_8390_hdr; ei_status.block_input = &hp_block_input; ei_status.block_output = &hp_block_output; hp_init_card(dev); return 0; } static int hp_open(struct device *dev) { ei_open(dev); MOD_INC_USE_COUNT; return 0; } static int hp_close(struct device *dev) { ei_close(dev); MOD_DEC_USE_COUNT; return 0; } static void hp_reset_8390(struct device *dev) { int hp_base = dev->base_addr - NIC_OFFSET; int saved_config = inb_p(hp_base + HP_CONFIGURE); if (ei_debug > 1) printk("resetting the 8390 time=%ld...", jiffies); outb_p(0x00, hp_base + HP_CONFIGURE); ei_status.txing = 0; /* Pause just a few cycles for the hardware reset to take place. */ SLOW_DOWN_IO; SLOW_DOWN_IO; outb_p(saved_config, hp_base + HP_CONFIGURE); SLOW_DOWN_IO; SLOW_DOWN_IO; if ((inb_p(hp_base+NIC_OFFSET+EN0_ISR) & ENISR_RESET) == 0) printk("%s: hp_reset_8390() did not complete.\n", dev->name); if (ei_debug > 1) printk("8390 reset done (%ld).", jiffies); return; } static void hp_get_8390_hdr(struct device *dev, struct e8390_pkt_hdr *hdr, int ring_page) { int nic_base = dev->base_addr; int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base); outb_p(sizeof(struct e8390_pkt_hdr), nic_base + EN0_RCNTLO); outb_p(0, nic_base + EN0_RCNTHI); outb_p(0, nic_base + EN0_RSARLO); /* On page boundary */ outb_p(ring_page, nic_base + EN0_RSARHI); outb_p(E8390_RREAD+E8390_START, nic_base); if (ei_status.word16) insw(nic_base - NIC_OFFSET + HP_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)>>1); else insb(nic_base - NIC_OFFSET + HP_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)); outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE); } /* Block input and output, similar to the Crynwr packet driver. If you are porting to a new ethercard look at the packet driver source for hints. The HP LAN doesn't use shared memory -- we put the packet out through the "remote DMA" dataport. */ static void hp_block_input(struct device *dev, int count, struct sk_buff *skb, int ring_offset) { int nic_base = dev->base_addr; int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE); int xfer_count = count; char *buf = skb->data; outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base); outb_p(count & 0xff, nic_base + EN0_RCNTLO); outb_p(count >> 8, nic_base + EN0_RCNTHI); outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO); outb_p(ring_offset >> 8, nic_base + EN0_RSARHI); outb_p(E8390_RREAD+E8390_START, nic_base); if (ei_status.word16) { insw(nic_base - NIC_OFFSET + HP_DATAPORT,buf,count>>1); if (count & 0x01) buf[count-1] = inb(nic_base - NIC_OFFSET + HP_DATAPORT), xfer_count++; } else { insb(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count); } /* This is for the ALPHA version only, remove for later releases. */ if (ei_debug > 0) { /* DMA termination address check... */ int high = inb_p(nic_base + EN0_RSARHI); int low = inb_p(nic_base + EN0_RSARLO); int addr = (high << 8) + low; /* Check only the lower 8 bits so we can ignore ring wrap. */ if (((ring_offset + xfer_count) & 0xff) != (addr & 0xff)) printk("%s: RX transfer address mismatch, %#4.4x vs. %#4.4x (actual).\n", dev->name, ring_offset + xfer_count, addr); } outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE); } static void hp_block_output(struct device *dev, int count, const unsigned char *buf, const int start_page) { int nic_base = dev->base_addr; int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE); outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE); /* Round the count up for word writes. Do we need to do this? What effect will an odd byte count have on the 8390? I should check someday. */ if (ei_status.word16 && (count & 0x01)) count++; /* We should already be in page 0, but to be safe... */ outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base); #ifdef NE8390_RW_BUGFIX /* Handle the read-before-write bug the same way as the Crynwr packet driver -- the NatSemi method doesn't work. */ outb_p(0x42, nic_base + EN0_RCNTLO); outb_p(0, nic_base + EN0_RCNTHI); outb_p(0xff, nic_base + EN0_RSARLO); outb_p(0x00, nic_base + EN0_RSARHI); #define NE_CMD 0x00 outb_p(E8390_RREAD+E8390_START, nic_base + NE_CMD); /* Make certain that the dummy read has occurred. */ inb_p(0x61); inb_p(0x61); #endif outb_p(count & 0xff, nic_base + EN0_RCNTLO); outb_p(count >> 8, nic_base + EN0_RCNTHI); outb_p(0x00, nic_base + EN0_RSARLO); outb_p(start_page, nic_base + EN0_RSARHI); outb_p(E8390_RWRITE+E8390_START, nic_base); if (ei_status.word16) { /* Use the 'rep' sequence for 16 bit boards. */ outsw(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count>>1); } else { outsb(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count); } /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here -- it's broken! */ /* This is for the ALPHA version only, remove for later releases. */ if (ei_debug > 0) { /* DMA termination address check... */ int high = inb_p(nic_base + EN0_RSARHI); int low = inb_p(nic_base + EN0_RSARLO); int addr = (high << 8) + low; if ((start_page << 8) + count != addr) printk("%s: TX Transfer address mismatch, %#4.4x vs. %#4.4x.\n", dev->name, (start_page << 8) + count, addr); } outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE); return; } /* This function resets the ethercard if something screws up. */ static void hp_init_card(struct device *dev) { int irq = dev->irq; NS8390_init(dev, 0); outb_p(irqmap[irq&0x0f] | HP_RUN, dev->base_addr - NIC_OFFSET + HP_CONFIGURE); return; } #ifdef MODULE #define MAX_HP_CARDS 4 /* Max number of HP cards per module */ #define NAMELEN 8 /* # of chars for storing dev->name */ static char namelist[NAMELEN * MAX_HP_CARDS] = { 0, }; static struct device dev_hp[MAX_HP_CARDS] = { { NULL, /* assign a chunk of namelist[] below */ 0, 0, 0, 0, 0, 0, 0, 0, 0, NULL, NULL }, }; static int io[MAX_HP_CARDS] = { 0, }; static int irq[MAX_HP_CARDS] = { 0, }; /* This is set up so that only a single autoprobe takes place per call. ISA device autoprobes on a running machine are not recommended. */ int init_module(void) { int this_dev, found = 0; for (this_dev = 0; this_dev < MAX_HP_CARDS; this_dev++) { struct device *dev = &dev_hp[this_dev]; dev->name = namelist+(NAMELEN*this_dev); dev->irq = irq[this_dev]; dev->base_addr = io[this_dev]; dev->init = hp_probe; if (io[this_dev] == 0) { if (this_dev != 0) break; /* only autoprobe 1st one */ printk(KERN_NOTICE "hp.c: Presently autoprobing (not recommended) for a single card.\n"); } if (register_netdev(dev) != 0) { printk(KERN_WARNING "hp.c: No HP card found (i/o = 0x%x).\n", io[this_dev]); if (found != 0) return 0; /* Got at least one. */ return -ENXIO; } found++; } return 0; } void cleanup_module(void) { int this_dev; for (this_dev = 0; this_dev < MAX_HP_CARDS; this_dev++) { struct device *dev = &dev_hp[this_dev]; if (dev->priv != NULL) { int ioaddr = dev->base_addr - NIC_OFFSET; kfree(dev->priv); dev->priv = NULL; free_irq(dev->irq, NULL); irq2dev_map[dev->irq] = NULL; release_region(ioaddr, HP_IO_EXTENT); unregister_netdev(dev); } } } #endif /* MODULE */ /* * Local variables: * compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c hp.c" * version-control: t * kept-new-versions: 5 * tab-width: 4 * c-indent-level: 4 * End: */