URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [scsi/] [Config.in] - Rev 1772
Go to most recent revision | Compare with Previous | Blame | View Log
comment 'SCSI support type (disk, tape, CD-ROM)'
dep_tristate 'SCSI disk support' CONFIG_BLK_DEV_SD $CONFIG_SCSI
dep_tristate 'SCSI tape support' CONFIG_CHR_DEV_ST $CONFIG_SCSI
dep_tristate 'SCSI CD-ROM support' CONFIG_BLK_DEV_SR $CONFIG_SCSI
dep_tristate 'SCSI generic support' CONFIG_CHR_DEV_SG $CONFIG_SCSI
comment 'Some SCSI devices (e.g. CD jukebox) support multiple LUNs'
bool 'Probe all LUNs on each SCSI device' CONFIG_SCSI_MULTI_LUN
bool 'Verbose SCSI error reporting (kernel size +=12K)' CONFIG_SCSI_CONSTANTS
mainmenu_option next_comment
comment 'SCSI low-level drivers'
dep_tristate '7000FASST SCSI support' CONFIG_SCSI_7000FASST $CONFIG_SCSI
dep_tristate 'ACARD SCSI support' CONFIG_SCSI_ACARD $CONFIG_SCSI
dep_tristate 'Adaptec AHA152X/2825 support' CONFIG_SCSI_AHA152X $CONFIG_SCSI
dep_tristate 'Adaptec AHA1542 support' CONFIG_SCSI_AHA1542 $CONFIG_SCSI
dep_tristate 'Adaptec AHA1740 support' CONFIG_SCSI_AHA1740 $CONFIG_SCSI
dep_tristate 'Adaptec AIC7xxx support' CONFIG_SCSI_AIC7XXX $CONFIG_SCSI
if [ "$CONFIG_SCSI_AIC7XXX" != "n" ]; then
bool ' Enable Tagged Command Queueing (TCQ) by default' CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT
int ' Maximum number of TCQ commands per device' CONFIG_AIC7XXX_CMDS_PER_DEVICE 8
bool ' Collect statistics to report in /proc' CONFIG_AIC7XXX_PROC_STATS N
int ' Delay in seconds after SCSI bus reset' CONFIG_AIC7XXX_RESET_DELAY 5
fi
dep_tristate 'AdvanSys SCSI support' CONFIG_SCSI_ADVANSYS $CONFIG_SCSI
dep_tristate 'Always IN2000 SCSI support' CONFIG_SCSI_IN2000 $CONFIG_SCSI
dep_tristate 'AM53/79C974 PCI SCSI support' CONFIG_SCSI_AM53C974 $CONFIG_SCSI
dep_tristate 'AMI MegaRAID support' CONFIG_SCSI_MEGARAID $CONFIG_SCSI
dep_tristate 'BusLogic SCSI support' CONFIG_SCSI_BUSLOGIC $CONFIG_SCSI
if [ "$CONFIG_SCSI_BUSLOGIC" != "n" ]; then
bool ' Omit FlashPoint support' CONFIG_SCSI_OMIT_FLASHPOINT
fi
dep_tristate 'DTC3180/3280 SCSI support' CONFIG_SCSI_DTC3280 $CONFIG_SCSI
dep_tristate 'EATA-DMA (DPT, NEC, AT&T, SNI, AST, Olivetti, Alphatronix) support' CONFIG_SCSI_EATA_DMA $CONFIG_SCSI
dep_tristate 'EATA-PIO (old DPT PM2001, PM2012A) support' CONFIG_SCSI_EATA_PIO $CONFIG_SCSI
dep_tristate 'EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support' CONFIG_SCSI_EATA $CONFIG_SCSI
if [ "$CONFIG_SCSI_EATA" != "n" ]; then
bool ' enable tagged command queueing' CONFIG_SCSI_EATA_TAGGED_QUEUE
bool ' enable elevator sorting' CONFIG_SCSI_EATA_LINKED_COMMANDS
int ' maximum number of queued commands' CONFIG_SCSI_EATA_MAX_TAGS 16
fi
dep_tristate 'Future Domain 16xx SCSI support' CONFIG_SCSI_FUTURE_DOMAIN $CONFIG_SCSI
dep_tristate 'Generic NCR5380/53c400 SCSI support' CONFIG_SCSI_GENERIC_NCR5380 $CONFIG_SCSI
if [ "$CONFIG_SCSI_GENERIC_NCR5380" != "n" ]; then
bool ' Enable NCR53c400 extensions' CONFIG_SCSI_GENERIC_NCR53C400
choice 'NCR5380/53c400 mapping method (use Port for T130B)' \
"Port CONFIG_SCSI_G_NCR5380_PORT \
Memory CONFIG_SCSI_G_NCR5380_MEM" Port
fi
dep_tristate 'Initio 91XX support' CONFIG_SCSI_INITIO $CONFIG_SCSI
dep_tristate 'Initio INI-A100U2W support' CONFIG_SCSI_INIA100 $CONFIG_SCSI
dep_tristate 'NCR53c406a SCSI support' CONFIG_SCSI_NCR53C406A $CONFIG_SCSI
dep_tristate 'symbios 53c416 SCSI support' CONFIG_SCSI_SYM53C416 $CONFIG_SCSI
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'NCR53c7,8xx SCSI support' CONFIG_SCSI_NCR53C7xx $CONFIG_SCSI
if [ "$CONFIG_SCSI_NCR53C7xx" != "n" ]; then
bool ' always negotiate synchronous transfers' CONFIG_SCSI_NCR53C7xx_sync
bool ' allow FAST-SCSI [10MHz]' CONFIG_SCSI_NCR53C7xx_FAST
bool ' allow DISCONNECT' CONFIG_SCSI_NCR53C7xx_DISCONNECT
fi
fi
if [ "$CONFIG_PCI" = "y" -a "$CONFIG_SCSI_NCR53C7xx" != "y" ]; then
dep_tristate 'NCR53C8XX SCSI support' CONFIG_SCSI_NCR53C8XX $CONFIG_SCSI
if [ "$CONFIG_SCSI_NCR53C8XX" != "n" ]; then
int ' default tagged command queue depth' CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS 8
int ' maximum number of queued commands' CONFIG_SCSI_NCR53C8XX_MAX_TAGS 32
int ' synchronous transfers frequency in MHz' CONFIG_SCSI_NCR53C8XX_SYNC 20
bool ' enable profiling' CONFIG_SCSI_NCR53C8XX_PROFILE
bool ' use normal IO' CONFIG_SCSI_NCR53C8XX_IOMAPPED
if [ "$CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS" = "0" ]; then
bool ' not allow targets to disconnect' CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
fi
if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
bool ' assume boards are SYMBIOS compatible' CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT
fi
fi
fi
dep_tristate 'IOMEGA Parallel Port ZIP drive SCSI support' CONFIG_SCSI_PPA $CONFIG_SCSI
if [ "$CONFIG_SCSI_PPA" != "n" ]; then
bool ' Buggy EPP chipset support' CONFIG_SCSI_PPA_HAVE_PEDANTIC
fi
dep_tristate 'PAS16 SCSI support' CONFIG_SCSI_PAS16 $CONFIG_SCSI
dep_tristate 'PCI-2000 support' CONFIG_SCSI_PCI2000 $CONFIG_SCSI
dep_tristate 'PCI2220I support' CONFIG_SCSI_PCI2220I $CONFIG_SCSI
dep_tristate 'PSI240I support' CONFIG_SCSI_PSI240I $CONFIG_SCSI
dep_tristate 'Qlogic FAS SCSI support' CONFIG_SCSI_QLOGIC_FAS $CONFIG_SCSI
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'Qlogic ISP SCSI support' CONFIG_SCSI_QLOGIC_ISP $CONFIG_SCSI
fi
dep_tristate 'Seagate ST-02 and Future Domain TMC-8xx SCSI support' CONFIG_SCSI_SEAGATE $CONFIG_SCSI
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'Tekram DC390(T) and Am53/79C974 SCSI support' CONFIG_SCSI_DC390T $CONFIG_SCSI
if [ "$CONFIG_SCSI_DC390T" != "n" ]; then
bool ' _omit_ support for non-DC390 adapters' CONFIG_SCSI_DC390T_NOGENSUPP
fi
fi
dep_tristate 'Trantor T128/T128F/T228 SCSI support' CONFIG_SCSI_T128 $CONFIG_SCSI
dep_tristate 'Tripace TC-2550x SCSI support' CONFIG_SCSI_TC2550 $CONFIG_SCSI
dep_tristate 'UltraStor 14F/34F support' CONFIG_SCSI_U14_34F $CONFIG_SCSI
if [ "$CONFIG_SCSI_U14_34F" != "n" ]; then
bool ' enable elevator sorting' CONFIG_SCSI_U14_34F_LINKED_COMMANDS
int ' maximum number of queued commands' CONFIG_SCSI_U14_34F_MAX_TAGS 8
fi
dep_tristate 'UltraStor SCSI support' CONFIG_SCSI_ULTRASTOR $CONFIG_SCSI
dep_tristate 'GDT SCSI Disk Array Controller support' CONFIG_SCSI_GDTH $CONFIG_SCSI
#dep_tristate 'SCSI debugging host adapter' CONFIG_SCSI_DEBUG $CONFIG_SCSI
endmenu
Go to most recent revision | Compare with Previous | Blame | View Log