URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [scsi/] [inia100.h] - Rev 1772
Go to most recent revision | Compare with Previous | Blame | View Log
/************************************************************************** * Initio A100 device driver for Linux. * * Copyright (c) 1994-1998 Initio Corporation * All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2, or (at your option) * any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; see the file COPYING. If not, write to * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. * * -------------------------------------------------------------------------- * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions, and the following disclaimer, * without modification, immediately at the beginning of the file. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * Where this Software is combined with software released under the terms of * the GNU Public License ("GPL") and the terms of the GPL would require the * combined work to also be released under the terms of the GPL, the terms * and conditions of this License will apply in addition to those of the * GPL with the exception of any terms or conditions of this License that * conflict with, or are expressly prohibited by, the GPL. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * ************************************************************************** * * Module: inia100.h * Description: INI-A100U2W LINUX device driver header * Revision History: * 06/18/98 HL, Initial production Version 1.02 * 12/19/98 bv, Use spinlocks for 2.1.95 and up ****************************************************************************/ #ifndef CVT_LINUX_VERSION #define CVT_LINUX_VERSION(V,P,S) (((V) * 65536) + ((P) * 256) + (S)) #endif #ifndef LINUX_VERSION_CODE #include <linux/version.h> #endif #include "sd.h" extern int inia100_detect(Scsi_Host_Template *); extern int inia100_command(Scsi_Cmnd *); extern int inia100_queue(Scsi_Cmnd *, void (*done) (Scsi_Cmnd *)); extern int inia100_abort(Scsi_Cmnd *); extern int inia100_reset(Scsi_Cmnd *, unsigned int); #if LINUX_VERSION_CODE >= CVT_LINUX_VERSION(1, 3, 0) extern int inia100_biosparam(Scsi_Disk *, kdev_t, int *); /*for linux v2.0 */ extern struct proc_dir_entry proc_scsi_inia100; #else extern int inia100_biosparam(Disk *, int, int *); /*for linux v1.13 */ #endif #define inia100_REVID "Initio INI-A100U2W SCSI device driver; Revision: 1.02a" #if LINUX_VERSION_CODE < CVT_LINUX_VERSION(1, 3, 0) #define INIA100 { \ NULL, \ NULL, \ inia100_REVID, \ inia100_detect, \ NULL, \ NULL, \ inia100_command, \ inia100_queue, \ inia100_abort, \ inia100_reset, \ NULL, \ inia100_biosparam, \ 1, \ 7, \ SG_ALL, \ 1, \ 0, \ 0, \ ENABLE_CLUSTERING \ } #else #if LINUX_VERSION_CODE < CVT_LINUX_VERSION(2, 1, 75) #define INIA100 { \ NULL, \ NULL, \ &proc_scsi_inia100, \ NULL, \ inia100_REVID, \ inia100_detect, \ NULL, \ NULL, \ inia100_command, \ inia100_queue, \ inia100_abort, \ inia100_reset, \ NULL, \ inia100_biosparam, \ 1, \ 7, \ 0, \ 1, \ 0, \ 0, \ ENABLE_CLUSTERING \ } #else /* Version >= 2.1.75 */ #define INIA100 { \ next: NULL, \ module: NULL, \ proc_dir: &proc_scsi_inia100, \ proc_info: NULL, \ name: inia100_REVID, \ detect: inia100_detect, \ release: NULL, \ info: NULL, \ command: inia100_command, \ queuecommand: inia100_queue, \ eh_strategy_handler: NULL, \ eh_abort_handler: NULL, \ eh_device_reset_handler: NULL, \ eh_bus_reset_handler: NULL, \ eh_host_reset_handler: NULL, \ abort: inia100_abort, \ reset: inia100_reset, \ slave_attach: NULL, \ bios_param: inia100_biosparam, \ can_queue: 1, \ this_id: 1, \ sg_tablesize: SG_ALL, \ cmd_per_lun: 1, \ present: 0, \ unchecked_isa_dma: 0, \ use_clustering: ENABLE_CLUSTERING, \ use_new_eh_code: 0 \ } #endif #endif #define VIRT_TO_BUS(i) (unsigned int) virt_to_bus((void *)(i)) #define ULONG unsigned long #define PVOID void * #define USHORT unsigned short #define UCHAR unsigned char #define BYTE unsigned char #define WORD unsigned short #define DWORD unsigned long #define UBYTE unsigned char #define UWORD unsigned short #define UDWORD unsigned long #ifdef ALPHA #define U32 unsigned int #else #define U32 unsigned long #endif #ifndef NULL #define NULL 0 /* zero */ #endif #ifndef TRUE #define TRUE (1) /* boolean true */ #endif #ifndef FALSE #define FALSE (0) /* boolean false */ #endif #ifndef FAILURE #define FAILURE (-1) #endif #if 1 #define ORC_MAXQUEUE 245 #else #define ORC_MAXQUEUE 25 #endif #define TOTAL_SG_ENTRY 32 #define MAX_TARGETS 16 #define IMAX_CDB 15 #define SENSE_SIZE 14 #define MAX_SUPPORTED_ADAPTERS 4 #define SUCCESSFUL 0x00 #define I920_DEVICE_ID 0x0002 /* Initio's inic-950 product ID */ /************************************************************************/ /* Scatter-Gather Element Structure */ /************************************************************************/ typedef struct ORC_SG_Struc { U32 SG_Ptr; /* Data Pointer */ U32 SG_Len; /* Data Length */ } ORC_SG; /* SCSI related definition */ #define DISC_NOT_ALLOW 0x80 /* Disconnect is not allowed */ #define DISC_ALLOW 0xC0 /* Disconnect is allowed */ #define ORC_OFFSET_SCB 16 #define ORC_MAX_SCBS 250 #define MAX_CHANNELS 2 #define MAX_ESCB_ELE 64 #define TCF_DRV_255_63 0x0400 /********************************************************/ /* Orchid Configuration Register Set */ /********************************************************/ #define ORC_PVID 0x00 /* Vendor ID */ #define ORC_VENDOR_ID 0x1101 /* Orchid vendor ID */ #define ORC_PDID 0x02 /* Device ID */ #define ORC_DEVICE_ID 0x1060 /* Orchid device ID */ #define ORC_COMMAND 0x04 /* Command */ #define BUSMS 0x04 /* BUS MASTER Enable */ #define IOSPA 0x01 /* IO Space Enable */ #define ORC_STATUS 0x06 /* Status register */ #define ORC_REVISION 0x08 /* Revision number */ #define ORC_BASE 0x10 /* Base address */ #define ORC_BIOS 0x50 /* Expansion ROM base address */ #define ORC_INT_NUM 0x3C /* Interrupt line */ #define ORC_INT_PIN 0x3D /* Interrupt pin */ /********************************************************/ /* Orchid Host Command Set */ /********************************************************/ #define ORC_CMD_NOP 0x00 /* Host command - NOP */ #define ORC_CMD_VERSION 0x01 /* Host command - Get F/W version */ #define ORC_CMD_ECHO 0x02 /* Host command - ECHO */ #define ORC_CMD_SET_NVM 0x03 /* Host command - Set NVRAM */ #define ORC_CMD_GET_NVM 0x04 /* Host command - Get NVRAM */ #define ORC_CMD_GET_BUS_STATUS 0x05 /* Host command - Get SCSI bus status */ #define ORC_CMD_ABORT_SCB 0x06 /* Host command - Abort SCB */ #define ORC_CMD_ISSUE_SCB 0x07 /* Host command - Issue SCB */ /********************************************************/ /* Orchid Register Set */ /********************************************************/ #define ORC_GINTS 0xA0 /* Global Interrupt Status */ #define QINT 0x04 /* Reply Queue Interrupt */ #define ORC_GIMSK 0xA1 /* Global Interrupt MASK */ #define MQINT 0x04 /* Mask Reply Queue Interrupt */ #define ORC_GCFG 0xA2 /* Global Configure */ #define EEPRG 0x01 /* Enable EEPROM programming */ #define ORC_GSTAT 0xA3 /* Global status */ #define WIDEBUS 0x10 /* Wide SCSI Devices connected */ #define ORC_HDATA 0xA4 /* Host Data */ #define ORC_HCTRL 0xA5 /* Host Control */ #define SCSIRST 0x80 /* SCSI bus reset */ #define HDO 0x40 /* Host data out */ #define HOSTSTOP 0x02 /* Host stop RISC engine */ #define DEVRST 0x01 /* Device reset */ #define ORC_HSTUS 0xA6 /* Host Status */ #define HDI 0x02 /* Host data in */ #define RREADY 0x01 /* RISC engine is ready to receive */ #define ORC_NVRAM 0xA7 /* Nvram port address */ #define SE2CS 0x008 #define SE2CLK 0x004 #define SE2DO 0x002 #define SE2DI 0x001 #define ORC_PQUEUE 0xA8 /* Posting queue FIFO */ #define ORC_PQCNT 0xA9 /* Posting queue FIFO Cnt */ #define ORC_RQUEUE 0xAA /* Reply queue FIFO */ #define ORC_RQUEUECNT 0xAB /* Reply queue FIFO Cnt */ #define ORC_FWBASEADR 0xAC /* Firmware base address */ #define ORC_EBIOSADR0 0xB0 /* External Bios address */ #define ORC_EBIOSADR1 0xB1 /* External Bios address */ #define ORC_EBIOSADR2 0xB2 /* External Bios address */ #define ORC_EBIOSDATA 0xB3 /* External Bios address */ #define ORC_SCBSIZE 0xB7 /* SCB size register */ #define ORC_SCBBASE0 0xB8 /* SCB base address 0 */ #define ORC_SCBBASE1 0xBC /* SCB base address 1 */ #define ORC_RISCCTL 0xE0 /* RISC Control */ #define PRGMRST 0x002 #define DOWNLOAD 0x001 #define ORC_PRGMCTR0 0xE2 /* RISC program counter */ #define ORC_PRGMCTR1 0xE3 /* RISC program counter */ #define ORC_RISCRAM 0xEC /* RISC RAM data port 4 bytes */ typedef struct orc_extended_scb { /* Extended SCB */ ORC_SG ESCB_SGList[TOTAL_SG_ENTRY]; /*0 Start of SG list */ Scsi_Cmnd *SCB_Srb; /*50 SRB Pointer */ } ESCB; /*********************************************************************** SCSI Control Block ************************************************************************/ typedef struct orc_scb { /* Scsi_Ctrl_Blk */ UBYTE SCB_Opcode; /*00 SCB command code&residual */ UBYTE SCB_Flags; /*01 SCB Flags */ UBYTE SCB_Target; /*02 Target Id */ UBYTE SCB_Lun; /*03 Lun */ U32 SCB_Reserved0; /*04 Reserved for ORCHID must 0 */ U32 SCB_XferLen; /*08 Data Transfer Length */ U32 SCB_Reserved1; /*0C Reserved for ORCHID must 0 */ U32 SCB_SGLen; /*10 SG list # * 8 */ U32 SCB_SGPAddr; /*14 SG List Buf physical Addr */ U32 SCB_SGPAddrHigh; /*18 SG Buffer high physical Addr */ UBYTE SCB_HaStat; /*1C Host Status */ UBYTE SCB_TaStat; /*1D Target Status */ UBYTE SCB_Status; /*1E SCB status */ UBYTE SCB_Link; /*1F Link pointer, default 0xFF */ UBYTE SCB_SenseLen; /*20 Sense Allocation Length */ UBYTE SCB_CDBLen; /*21 CDB Length */ UBYTE SCB_Ident; /*22 Identify */ UBYTE SCB_TagMsg; /*23 Tag Message */ UBYTE SCB_CDB[IMAX_CDB]; /*24 SCSI CDBs */ UBYTE SCB_ScbIdx; /*3C Index for this ORCSCB */ U32 SCB_SensePAddr; /*34 Sense Buffer physical Addr */ ESCB *SCB_EScb; /*38 Extended SCB Pointer */ #ifndef ALPHA UBYTE SCB_Reserved2[4]; /*3E Reserved for Driver use */ #endif } ORC_SCB; /* Opcodes of ORCSCB_Opcode */ #define ORC_EXECSCSI 0x00 /* SCSI initiator command with residual */ #define ORC_BUSDEVRST 0x01 /* SCSI Bus Device Reset */ /* Status of ORCSCB_Status */ #define SCB_COMPLETE 0x00 /* SCB request completed */ #define SCB_POST 0x01 /* SCB is posted by the HOST */ /* Bit Definition for ORCSCB_Flags */ #define SCF_DISINT 0x01 /* Disable HOST interrupt */ #define SCF_DIR 0x18 /* Direction bits */ #define SCF_NO_DCHK 0x00 /* Direction determined by SCSI */ #define SCF_DIN 0x08 /* From Target to Initiator */ #define SCF_DOUT 0x10 /* From Initiator to Target */ #define SCF_NO_XF 0x18 /* No data transfer */ #define SCF_POLL 0x40 /* Error Codes for ORCSCB_HaStat */ #define HOST_SEL_TOUT 0x11 #define HOST_DO_DU 0x12 #define HOST_BUS_FREE 0x13 #define HOST_BAD_PHAS 0x14 #define HOST_INV_CMD 0x16 #define HOST_SCSI_RST 0x1B #define HOST_DEV_RST 0x1C /* Error Codes for ORCSCB_TaStat */ #define TARGET_CHK_COND 0x02 #define TARGET_BUSY 0x08 #define TARGET_TAG_FULL 0x28 /* Queue tag msg: Simple_quque_tag, Head_of_queue_tag, Ordered_queue_tag */ #define MSG_STAG 0x20 #define MSG_HTAG 0x21 #define MSG_OTAG 0x22 #define MSG_IGNOREWIDE 0x23 #define MSG_IDENT 0x80 #define MSG_DISC 0x40 /* Disconnect allowed */ /* SCSI MESSAGE */ #define MSG_EXTEND 0x01 #define MSG_SDP 0x02 #define MSG_ABORT 0x06 #define MSG_REJ 0x07 #define MSG_NOP 0x08 #define MSG_PARITY 0x09 #define MSG_DEVRST 0x0C #define MSG_STAG 0x20 /*********************************************************************** Target Device Control Structure **********************************************************************/ typedef struct ORC_Tar_Ctrl_Struc { UBYTE TCS_DrvDASD; /* 6 */ UBYTE TCS_DrvSCSI; /* 7 */ UBYTE TCS_DrvHead; /* 8 */ UWORD TCS_DrvFlags; /* 4 */ UBYTE TCS_DrvSector; /* 7 */ } ORC_TCS, *PORC_TCS; /* Bit Definition for TCF_DrvFlags */ #define TCS_DF_NODASD_SUPT 0x20 /* Suppress OS/2 DASD Mgr support */ #define TCS_DF_NOSCSI_SUPT 0x40 /* Suppress OS/2 SCSI Mgr support */ /*********************************************************************** Host Adapter Control Structure ************************************************************************/ typedef struct ORC_Ha_Ctrl_Struc { USHORT HCS_Base; /* 00 */ UBYTE HCS_Index; /* 02 */ UBYTE HCS_Intr; /* 04 */ UBYTE HCS_SCSI_ID; /* 06 H/A SCSI ID */ UBYTE HCS_BIOS; /* 07 BIOS configuration */ UBYTE HCS_Flags; /* 0B */ UBYTE HCS_HAConfig1; /* 1B SCSI0MAXTags */ UBYTE HCS_MaxTar; /* 1B SCSI0MAXTags */ USHORT HCS_Units; /* Number of units this adapter */ USHORT HCS_AFlags; /* Adapter info. defined flags */ ULONG HCS_Timeout; /* Adapter timeout value */ PVOID HCS_virScbArray; /* 28 Virtual Pointer to SCB array */ U32 HCS_physScbArray; /* Scb Physical address */ PVOID HCS_virEscbArray; /* Virtual pointer to ESCB Scatter list */ U32 HCS_physEscbArray; /* scatter list Physical address */ UBYTE TargetFlag[16]; /* 30 target configuration, TCF_EN_TAG */ UBYTE MaximumTags[16]; /* 40 ORC_MAX_SCBS */ UBYTE ActiveTags[16][16]; /* 50 */ ORC_TCS HCS_Tcs[16]; /* 28 */ U32 BitAllocFlag[MAX_CHANNELS][8]; /* Max STB is 256, So 256/32 */ #if LINUX_VERSION_CODE >= CVT_LINUX_VERSION(2,1,95) spinlock_t BitAllocFlagLock; #endif Scsi_Cmnd *pSRB_head; Scsi_Cmnd *pSRB_tail; #if LINUX_VERSION_CODE >= CVT_LINUX_VERSION(2,1,95) spinlock_t pSRB_lock; #endif } ORC_HCS; /* Bit Definition for HCS_Flags */ #define HCF_SCSI_RESET 0x01 /* SCSI BUS RESET */ #define HCF_PARITY 0x02 /* parity card */ #define HCF_LVDS 0x10 /* parity card */ /* Bit Definition for TargetFlag */ #define TCF_EN_255 0x08 #define TCF_EN_TAG 0x10 #define TCF_BUSY 0x20 #define TCF_DISCONNECT 0x40 #define TCF_SPIN_UP 0x80 /* Bit Definition for HCS_AFlags */ #define HCS_AF_IGNORE 0x01 /* Adapter ignore */ #define HCS_AF_DISABLE_RESET 0x10 /* Adapter disable reset */ #define HCS_AF_DISABLE_ADPT 0x80 /* Adapter disable */ /*---------------------------------------*/ /* TimeOut for RESET to complete (30s) */ /* */ /* After a RESET the drive is checked */ /* every 200ms. */ /*---------------------------------------*/ #define DELAYED_RESET_MAX (30*1000L) #define DELAYED_RESET_INTERVAL 200L /*----------------------------------------------*/ /* TimeOut for IRQ from last interrupt (5s) */ /*----------------------------------------------*/ #define IRQ_TIMEOUT_INTERVAL (5*1000L) /*----------------------------------------------*/ /* Retry Delay interval (200ms) */ /*----------------------------------------------*/ #define DELAYED_RETRY_INTERVAL 200L #define INQUIRY_SIZE 36 #define CAPACITY_SIZE 8 #define DEFAULT_SENSE_LEN 14 #define DEVICE_NOT_FOUND 0x86 /*----------------------------------------------*/ /* Definition for PCI device */ /*----------------------------------------------*/ #define MAX_PCI_DEVICES 21 #define MAX_PCI_BUSES 8
Go to most recent revision | Compare with Previous | Blame | View Log