Subversion Repositories or1k

/*
 * This driver adapted from Drew Eckhardt's Trantor T128 driver
 *
 * Copyright 1993, Drew Eckhardt
 *	Visionary Computing
 *	(Unix and Linux consulting and custom programming)
 *	drew@colorado.edu
 *      +1 (303) 666-5836
 *
 *  ( Based on T128 - DISTRIBUTION RELEASE 3. ) 
 *
 * Modified to work with the Pro Audio Spectrum/Studio 16
 * by John Weidman.
 *
 *
 * For more information, please consult 
 *
 * Media Vision
 * (510) 770-8600
 * (800) 348-7116
 * 
 * and 
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
 *
 * NCR Microelectronics
 * 1635 Aeroplaza Drive
 * Colorado Springs, CO 80916
 * 1+ (719) 578-3400
 * 1+ (800) 334-5454
 */
 
 
#ifndef PAS16_H
#define PAS16_H
 
#define PAS16_PUBLIC_RELEASE 3
 
#define PDEBUG_INIT	0x1
#define PDEBUG_TRANSFER 0x2
 
#define PAS16_DEFAULT_BASE_1  0x388
#define PAS16_DEFAULT_BASE_2  0x384
#define PAS16_DEFAULT_BASE_3  0x38c
#define PAS16_DEFAULT_BASE_4  0x288
 
#define PAS16_DEFAULT_BOARD_1_IRQ 10
#define PAS16_DEFAULT_BOARD_2_IRQ 12
#define PAS16_DEFAULT_BOARD_3_IRQ 14
#define PAS16_DEFAULT_BOARD_4_IRQ 15
 
 
/*
 * The Pro Audio Spectrum boards are I/O mapped. They use a Zilog 5380
 * SCSI controller, which is the equivalent of NCR's 5380.  "Pseudo-DMA"
 * architecture is used, where a PAL drives the DMA signals on the 5380
 * allowing fast, blind transfers with proper handshaking. 
 */
 
 
/* The Time-out Counter register is used to safe-guard against a stuck
 * bus (in the case of RDY driven handshake) or a stuck byte (if 16-Bit
 * DMA conversion is used).  The counter uses a 28.224MHz clock
 * divided by 14 as its clock source.  In the case of a stuck byte in
 * the holding register, an interrupt is generated (and mixed with the
 * one with the drive) using the CD-ROM interrupt pointer.
 */
 
#define P_TIMEOUT_COUNTER_REG	0x4000
#define P_TC_DISABLE	0x80	/* Set to 0 to enable timeout int. */
				/* Bits D6-D0 contain timeout count */
 
 
#define P_TIMEOUT_STATUS_REG_OFFSET	0x4001
#define P_TS_TIM		0x80	/* check timeout status */
					/* Bits D6-D4 N/U */
#define P_TS_ARM_DRQ_INT	0x08	/* Arm DRQ Int.  When set high,
					 * the next rising edge will
					 * cause a CD-ROM interrupt.
					 * When set low, the interrupt
					 * will be cleared.  There is
					 * no status available for
					 * this interrupt.
					 */
#define P_TS_ENABLE_TO_ERR_INTERRUPT	/* Enable timeout error int. */
#define P_TS_ENABLE_WAIT		/* Enable Wait */
 
#define P_TS_CT			0x01	/* clear timeout. Note: writing
					 * to this register clears the
					 * timeout error int. or status
					 */
 
 
/*
 * The data register reads/writes to/from the 5380 in pseudo-DMA mode
 */ 
 
#define P_DATA_REG_OFFSET	0x5c00	/* rw */
 
#define P_STATUS_REG_OFFSET	0x5c01	/* ro */
#define P_ST_RDY		0x80	/* 5380 DDRQ Status */
 
#define P_IRQ_STATUS		0x5c03
#define P_IS_IRQ		0x80	/* DIRQ status */
 
#define PCB_CONFIG 0x803
#define MASTER_ADDRESS_PTR 0x9a01  /* Fixed position - no relo */
#define SYS_CONFIG_4 0x8003
#define WAIT_STATE 0xbc00
#define OPERATION_MODE_1 0xec03
#define IO_CONFIG_3 0xf002
 
 
#ifndef ASM
int pas16_abort(Scsi_Cmnd *);
int pas16_biosparam(Disk *, kdev_t, int*);
int pas16_detect(Scsi_Host_Template *);
int pas16_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
int pas16_reset(Scsi_Cmnd *, unsigned int);
int pas16_proc_info (char *buffer ,char **start, off_t offset,
		     int length, int hostno, int inout);
 
#ifndef NULL
#define NULL 0
#endif
 
#ifndef CMD_PER_LUN
#define CMD_PER_LUN 2
#endif
 
#ifndef CAN_QUEUE
#define CAN_QUEUE 32 
#endif
 
/* 
 * I hadn't thought of this with the earlier drivers - but to prevent
 * macro definition conflicts, we shouldn't define all of the internal
 * macros when this is being used solely for the host stub.
 */
 
#if defined(HOSTS_C) || defined(MODULE)
 
#define MV_PAS16 {NULL, NULL, NULL, NULL, \
	"Pro Audio Spectrum-16 SCSI", 		\
	pas16_detect, NULL, NULL,					\
	NULL, pas16_queue_command, pas16_abort, pas16_reset, NULL, 	\
	pas16_biosparam, 						\
	/* can queue */ CAN_QUEUE, /* id */ 7, SG_ALL,			\
	/* cmd per lun */ CMD_PER_LUN , 0, 0, DISABLE_CLUSTERING}
 
#endif
#ifndef HOSTS_C
 
#define NCR5380_implementation_fields \
    volatile unsigned short io_port
 
#define NCR5380_local_declare() \
    volatile unsigned short io_port
 
#define NCR5380_setup(instance) \
    io_port = (instance)->io_port
 
#define PAS16_io_port(reg) ( io_port + pas16_offset[(reg)] )
 
#if !(PDEBUG & PDEBUG_TRANSFER) 
#define NCR5380_read(reg) ( inb(PAS16_io_port(reg)) )
#define NCR5380_write(reg, value) ( outb((value),PAS16_io_port(reg)) )
#else
#define NCR5380_read(reg)						\
    (((unsigned char) printk("scsi%d : read register %d at io_port %04x\n"\
    , instance->hostno, (reg), PAS16_io_port(reg))), inb( PAS16_io_port(reg)) )
 
#define NCR5380_write(reg, value) 					\
    (printk("scsi%d : write %02x to register %d at io_port %04x\n", 	\
	    instance->hostno, (value), (reg), PAS16_io_port(reg)),	\
    outb( (value),PAS16_io_port(reg) ) )
 
#endif
 
 
#define NCR5380_intr pas16_intr
#define NCR5380_queue_command pas16_queue_command
#define NCR5380_abort pas16_abort
#define NCR5380_reset pas16_reset
#define NCR5380_proc_info pas16_proc_info
 
/* 15 14 12 10 7 5 3 
   1101 0100 1010 1000 */
 
#define PAS16_IRQS 0xd4a8 
 
#endif /* else def HOSTS_C */
#endif /* ndef ASM */
#endif /* PAS16_H */