Subversion Repositories or1k

/* 
 *  sym53c416.c
 *  Low-level SCSI driver for sym53c416 chip.
 *  Copyright (C) 1998 Lieven Willems (lw_linux@hotmail.com)
 * 
 *  LILO command line usage: sym53c416=<PORTBASE>[,<IRQ>]
 *
 *  This program is free software; you can redistribute it and/or modify it
 *  under the terms of the GNU General Public License as published by the
 *  Free Software Foundation; either version 2, or (at your option) any
 *  later version.
 *
 *  This program is distributed in the hope that it will be useful, but
 *  WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 *  General Public License for more details.
 *
 */
 
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <asm/dma.h>
#include <asm/system.h>
#include <asm/io.h>
#include <linux/blk.h>
#include "scsi.h"
#include "hosts.h"
#include "sd.h"
#include "sym53c416.h"
 
#define VERSION_STRING        "Version 1.0.0"
 
#define TC_LOW       0x00     /* Transfer counter low        */
#define TC_MID       0x01     /* Transfer counter mid        */
#define SCSI_FIFO    0x02     /* SCSI FIFO register          */
#define COMMAND_REG  0x03     /* Command Register            */
#define STATUS_REG   0x04     /* Status Register (READ)      */
#define DEST_BUS_ID  0x04     /* Destination Bus ID (WRITE)  */
#define INT_REG      0x05     /* Interrupt Register (READ)   */
#define TOM          0x05     /* Time out multiplier (WRITE) */
#define STP          0x06     /* Synchronous Transfer period */
#define SYNC_OFFSET  0x07     /* Synchronous Offset          */
#define CONF_REG_1   0x08     /* Configuration register 1    */
#define CONF_REG_2   0x0B     /* Configuration register 2    */
#define CONF_REG_3   0x0C     /* Configuration register 3    */
#define CONF_REG_4   0x0D     /* Configuration register 4    */
#define TC_HIGH      0x0E     /* Transfer counter high       */
#define PIO_FIFO_1   0x10     /* PIO FIFO register 1         */
#define PIO_FIFO_2   0x11     /* PIO FIFO register 2         */
#define PIO_FIFO_3   0x12     /* PIO FIFO register 3         */
#define PIO_FIFO_4   0x13     /* PIO FIFO register 4         */
#define PIO_FIFO_CNT 0x14     /* PIO FIFO count              */
#define PIO_INT_REG  0x15     /* PIO interrupt register      */
#define CONF_REG_5   0x16     /* Configuration register 5    */
#define FEATURE_EN   0x1D     /* Feature Enable register     */
 
/* Configuration register 1 entries: */
/* Bits 2-0: SCSI ID of host adapter */
#define SCM    0x80                     /* Slow Cable Mode              */
#define SRID   0x40                     /* SCSI Reset Interrupt Disable */
#define PTM    0x20                     /* Parity Test Mode             */
#define EPC    0x10                     /* Enable Parity Checking       */
#define CTME   0x08                     /* Special Test Mode            */
 
/* Configuration register 2 entries: */
#define FE     0x40                     /* Features Enable              */
#define SCSI2  0x08                     /* SCSI 2 Enable                */
#define TBPA   0x04                     /* Target Bad Parity Abort      */
 
/* Configuration register 3 entries: */
#define IDMRC  0x80                     /* ID Message Reserved Check    */
#define QTE    0x40                     /* Queue Tag Enable             */
#define CDB10  0x20                     /* Command Descriptor Block 10  */
#define FSCSI  0x10                     /* FastSCSI                     */
#define FCLK   0x08                     /* FastClock                    */
 
/* Configuration register 4 entries: */
#define RBS    0x08                     /* Register bank select         */
#define EAN    0x04                     /* Enable Active Negotiation    */
 
/* Configuration register 5 entries: */
#define LPSR   0x80                     /* Lower Power SCSI Reset       */
#define IE     0x20                     /* Interrupt Enable             */
#define LPM    0x02                     /* Low Power Mode               */
#define WSE0   0x01                     /* 0WS Enable                   */
 
/* Interrupt register entries: */
#define SRST   0x80                     /* SCSI Reset                   */
#define ILCMD  0x40                     /* Illegal Command              */
#define DIS    0x20                     /* Disconnect                   */
#define BS     0x10                     /* Bus Service                  */
#define FC     0x08                     /* Function Complete            */
#define RESEL  0x04                     /* Reselected                   */
#define SI     0x03                     /* Selection Interrupt          */
 
/* Status Register Entries: */
#define SCI    0x80                     /* SCSI Core Int                */
#define GE     0x40                     /* Gross Error                  */
#define PE     0x20                     /* Parity Error                 */
#define TC     0x10                     /* Terminal Count               */
#define VGC    0x08                     /* Valid Group Code             */
#define PHBITS 0x07                     /* Phase bits                   */
 
/* PIO Interrupt Register Entries: */
#define SCI    0x80                     /* SCSI Core Int                */
#define PFI    0x40                     /* PIO FIFO Interrupt           */
#define FULL   0x20                     /* PIO FIFO Full                */
#define EMPTY  0x10                     /* PIO FIFO Empty               */
#define CE     0x08                     /* Collision Error              */
#define OUE    0x04                     /* Overflow / Underflow error   */
#define FIE    0x02                     /* Full Interrupt Enable        */
#define EIE    0x01                     /* Empty Interrupt Enable       */
 
/* SYM53C416 SCSI phases (lower 3 bits of SYM53C416_STATUS_REG) */
#define PHASE_DATA_OUT    0x00
#define PHASE_DATA_IN     0x01
#define PHASE_COMMAND     0x02
#define PHASE_STATUS      0x03
#define PHASE_RESERVED_1  0x04
#define PHASE_RESERVED_2  0x05
#define PHASE_MESSAGE_OUT 0x06
#define PHASE_MESSAGE_IN  0x07
 
/* SYM53C416 core commands */
#define NOOP                      0x00
#define FLUSH_FIFO                0x01
#define RESET_CHIP                0x02
#define RESET_SCSI_BUS            0x03
#define DISABLE_SEL_RESEL         0x45
#define RESEL_SEQ                 0x40
#define SEL_WITHOUT_ATN_SEQ       0x41
#define SEL_WITH_ATN_SEQ          0x42
#define SEL_WITH_ATN_AND_STOP_SEQ 0x43
#define ENABLE_SEL_RESEL          0x44
#define SEL_WITH_ATN3_SEQ         0x46
#define RESEL3_SEQ                0x47
#define SND_MSG                   0x20
#define SND_STAT                  0x21
#define SND_DATA                  0x22
#define DISCONNECT_SEQ            0x23
#define TERMINATE_SEQ             0x24
#define TARGET_COMM_COMPLETE_SEQ  0x25
#define DISCONN                   0x27
#define RECV_MSG_SEQ              0x28
#define RECV_CMD                  0x29
#define RECV_DATA                 0x2A
#define RECV_CMD_SEQ              0x2B
#define TARGET_ABORT_PIO          0x04
#define TRANSFER_INFORMATION      0x10
#define INIT_COMM_COMPLETE_SEQ    0x11
#define MSG_ACCEPTED              0x12
#define TRANSFER_PAD              0x18
#define SET_ATN                   0x1A
#define RESET_ATN                 0x1B
#define ILLEGAL                   0xFF
 
#define PIO_MODE                  0x80
 
#define IO_RANGE 0x20         /* 0x00 - 0x1F                   */
#define ID       "sym53c416"
#define PIO_SIZE 128          /* Size of PIO fifo is 128 bytes */
 
#define READ_TIMEOUT              150
#define WRITE_TIMEOUT             150
 
#ifdef MODULE
 
#define sym53c416_base sym53c416
#define sym53c416_base_1 sym53c416_1
#define sym53c416_base_2 sym53c416_2
#define sym53c416_base_3 sym53c416_3
 
static unsigned short sym53c416_base = 0;
static unsigned int sym53c416_irq = 0;
static unsigned short sym53c416_base_1 = 0;
static unsigned int sym53c416_irq_1 = 0;
static unsigned short sym53c416_base_2 = 0;
static unsigned int sym53c416_irq_2 = 0;
static unsigned short sym53c416_base_3 = 0;
static unsigned int sym53c416_irq_3 = 0;
 
#endif
 
/* #define DEBUG */
 
/* Macro for debugging purposes */
 
#ifdef DEBUG
#define DEB(x) x
#else
#define DEB(x)
#endif
 
#define MAXHOSTS 4
 
enum phases
  {
  idle,
  data_out,
  data_in,
  command_ph,
  status_ph,
  message_out,
  message_in
  };
 
typedef struct
  {
  int base;
  int irq;
  int scsi_id;
  } host;
 
host hosts[MAXHOSTS] = {
                       {0, 0, SYM53C416_SCSI_ID},
                       {0, 0, SYM53C416_SCSI_ID},
                       {0, 0, SYM53C416_SCSI_ID},
                       {0, 0, SYM53C416_SCSI_ID}
                       };
 
static int host_index = 0;
 
static char info[120];
 
static Scsi_Cmnd *current_command = NULL;
 
struct proc_dir_entry proc_scsi_sym53c416 = {PROC_SCSI_SYM53C416, 7, ID, S_IFDIR | S_IRUGO | S_IXUGO, 2};
 
int fastpio = 1;
 
int probeaddrs[] = {0x200, 0x220, 0x240, 0};
 
static void sym53c416_set_transfer_counter(int base, unsigned int len)
  {
  /* Program Transfer Counter */
  outb(len & 0x0000FF, base + TC_LOW);
  outb((len & 0x00FF00) >> 8, base + TC_MID);
  outb((len & 0xFF0000) >> 16, base + TC_HIGH);
  }
 
/* Returns the number of bytes read */
static __inline__ unsigned int sym53c416_read(int base, unsigned char *buffer, unsigned int len)
  {
  unsigned int orig_len = len;
  unsigned long flags = 0;
  unsigned int bytes_left;
  int i;
  int timeout = READ_TIMEOUT;
 
  /* Do transfer */
  save_flags(flags);
  cli();
  while(len && timeout)
    {
    bytes_left = inb(base + PIO_FIFO_CNT); /* Number of bytes in the PIO FIFO */
    if(fastpio && bytes_left > 3)
      {
      insl(base + PIO_FIFO_1, buffer, bytes_left >> 2);
      buffer += bytes_left & 0xFC;
      len -= bytes_left & 0xFC;
      }
    else if(bytes_left > 0)
      {
      len -= bytes_left;
      for(; bytes_left > 0; bytes_left--)
        *(buffer++) = inb(base + PIO_FIFO_1);
      }
    else
      {
      i = jiffies + timeout;
      restore_flags(flags);
      while(jiffies < i && (inb(base + PIO_INT_REG) & EMPTY) && timeout)
        if(inb(base + PIO_INT_REG) & SCI)
          timeout = 0;
      save_flags(flags);
      cli();
      if(inb(base + PIO_INT_REG) & EMPTY)
        timeout = 0;
      }
    }
  restore_flags(flags);
  return orig_len - len;
  }
 
/* Returns the number of bytes written */
static __inline__ unsigned int sym53c416_write(int base, unsigned char *buffer, unsigned int len)
  {
  unsigned int orig_len = len;
  unsigned long flags = 0;
  unsigned int bufferfree;
  unsigned int i;
  unsigned int timeout = WRITE_TIMEOUT;
 
  /* Do transfer */
  save_flags(flags);
  cli();
  while(len && timeout)
    {
    bufferfree = PIO_SIZE - inb(base + PIO_FIFO_CNT);
    if(bufferfree > len)
      bufferfree = len;
    if(fastpio && bufferfree > 3)
      {
      outsl(base + PIO_FIFO_1, buffer, bufferfree >> 2);
      buffer += bufferfree & 0xFC;
      len -= bufferfree & 0xFC;
      }
    else if(bufferfree > 0)
      {
      len -= bufferfree;
      for(; bufferfree > 0; bufferfree--)
        outb(*(buffer++), base + PIO_FIFO_1);
      }
    else
      {
      i = jiffies + timeout;
      restore_flags(flags);
      while(jiffies < i && (inb(base + PIO_INT_REG) & FULL) && timeout)
        ;
      save_flags(flags);
      cli();
      if(inb(base + PIO_INT_REG) & FULL)
        timeout = 0;
      }
    }
  restore_flags(flags);
  return orig_len - len;
  }
 
static void sym53c416_intr_handle(int irq, void *dev_id, struct pt_regs *regs)
  {
  int base = 0;
  int i;
  unsigned long flags = 0;
  unsigned char status_reg, pio_int_reg, int_reg;
  struct scatterlist *sglist;
  unsigned int sgcount;
  unsigned int tot_trans = 0;
 
  /* We search the base address of the host adapter which caused the interrupt */
  for(i = 0; i < host_index && !base; i++)
    if(irq == hosts[i].irq)
      base = hosts[i].base;
  /* If no adapter found, we cannot handle the interrupt. Leave a message */
  /* and continue. This should never happen...                            */
  if(!base)
    {
    printk("sym53c416: No host adapter defined for interrupt %d\n", irq);
    return;
    }
  /* Now we have the base address and we can start handling the interrupt */
  save_flags(flags);
  cli();
  status_reg = inb(base + STATUS_REG);
  pio_int_reg = inb(base + PIO_INT_REG);
  int_reg = inb(base + INT_REG);
  restore_flags(flags);
 
  /* First, we handle error conditions */
  if(int_reg & SCI)         /* SCSI Reset */
    {
    printk("sym53c416: Warning: Reset received\n");
    current_command->SCp.phase = idle;
    current_command->result = DID_RESET << 16;
    current_command->scsi_done(current_command);
    return;
    }
  if(int_reg & ILCMD)       /* Illegal Command */
    {
    printk("sym53c416: Warning: Illegal Command: 0x%02x\n", inb(base + COMMAND_REG));
    current_command->SCp.phase = idle;
    current_command->result = DID_ERROR << 16;
    current_command->scsi_done(current_command);
    return;
    }
  if(status_reg & GE)         /* Gross Error */
    {
    printk("sym53c416: Warning: Gross Error\n");
    current_command->SCp.phase = idle;
    current_command->result = DID_ERROR << 16;
    current_command->scsi_done(current_command);
    return;
    }
  if(status_reg & PE)         /* Parity Error */
    {
    printk("sym53c416: Warning: Parity Error\n");
    current_command->SCp.phase = idle;
    current_command->result = DID_PARITY << 16;
    current_command->scsi_done(current_command);
    return;
    }
  if(pio_int_reg & (CE | OUE))
    {
    printk("sym53c416: Warning: PIO Interrupt Error\n");
    current_command->SCp.phase = idle;
    current_command->result = DID_ERROR << 16;
    current_command->scsi_done(current_command);
    return;
    }
  if(int_reg & DIS)           /* Disconnect */
    {
    if(current_command->SCp.phase != message_in)
      current_command->result = DID_NO_CONNECT << 16;
    else
      current_command->result = (current_command->SCp.Status & 0xFF) | ((current_command->SCp.Message & 0xFF) << 8) | (DID_OK << 16);
    current_command->SCp.phase = idle;
    current_command->scsi_done(current_command);
    return;
    }
  /* Now we handle SCSI phases         */
  switch(status_reg & PHBITS)       /* Filter SCSI phase out of status reg */
    {
    case PHASE_DATA_OUT:
      {
      if(int_reg & BS)
        {
        current_command->SCp.phase = data_out;
        outb(FLUSH_FIFO, base + COMMAND_REG);
        sym53c416_set_transfer_counter(base, current_command->request_bufflen);
        outb(TRANSFER_INFORMATION | PIO_MODE, base + COMMAND_REG);
        if(!current_command->use_sg)
          tot_trans = sym53c416_write(base, current_command->request_buffer, current_command->request_bufflen);
        else
          {
          sgcount = current_command->use_sg;
          sglist = current_command->request_buffer;
          while(sgcount--)
            {
            tot_trans += sym53c416_write(base, sglist->address, sglist->length);
            sglist++;
            }
          }
        if(tot_trans < current_command->underflow)
          printk("sym53c416: Warning: underflow, wrote %d bytes, request for %d bytes\n", tot_trans, current_command->underflow);
        }
      break;
      }
    case PHASE_DATA_IN:
      {
      if(int_reg & BS)
        {
        current_command->SCp.phase = data_in;
        outb(FLUSH_FIFO, base + COMMAND_REG);
        sym53c416_set_transfer_counter(base, current_command->request_bufflen);
        outb(TRANSFER_INFORMATION | PIO_MODE, base + COMMAND_REG);
        if(!current_command->use_sg)
          tot_trans = sym53c416_read(base, current_command->request_buffer, current_command->request_bufflen);
        else
          {
          sgcount = current_command->use_sg;
          sglist = current_command->request_buffer;
          while(sgcount--)
            {
            tot_trans += sym53c416_read(base, sglist->address, sglist->length);
            sglist++;
            }
          }
        if(tot_trans < current_command->underflow)
          printk("sym53c416: Warning: underflow, read %d bytes, request for %d bytes\n", tot_trans, current_command->underflow);
        }
      break;
      }
    case PHASE_COMMAND:
      {
      current_command->SCp.phase = command_ph;
      printk("sym53c416: Warning: Unknown interrupt in command phase\n");
      break;
      }
    case PHASE_STATUS:
      {
      current_command->SCp.phase = status_ph;
      outb(FLUSH_FIFO, base + COMMAND_REG);
      outb(INIT_COMM_COMPLETE_SEQ, base + COMMAND_REG);
      break;
      }
    case PHASE_RESERVED_1:
    case PHASE_RESERVED_2:
      {
      printk("sym53c416: Warning: Reserved phase\n");
      break;
      }
    case PHASE_MESSAGE_OUT:
      {
      current_command->SCp.phase = message_out;
      outb(SET_ATN, base + COMMAND_REG);
      outb(MSG_ACCEPTED, base + COMMAND_REG);
      break;
      }
    case PHASE_MESSAGE_IN:
      {
      current_command->SCp.phase = message_in;
      current_command->SCp.Status = inb(base + SCSI_FIFO);
      current_command->SCp.Message = inb(base + SCSI_FIFO);
      if(current_command->SCp.Message == SAVE_POINTERS || current_command->SCp.Message == DISCONNECT)
        outb(SET_ATN, base + COMMAND_REG);
      outb(MSG_ACCEPTED, base + COMMAND_REG);
      break;
      }
    }
  }
 
static void sym53c416_init(int base, int scsi_id)
  {
  outb(RESET_CHIP, base + COMMAND_REG);
  outb(NOOP, base + COMMAND_REG);
  outb(0x99, base + TOM); /* Time out of 250 ms */
  outb(0x05, base + STP);
  outb(0x00, base + SYNC_OFFSET);
  outb(EPC | scsi_id, base + CONF_REG_1);
  outb(FE | SCSI2 | TBPA, base + CONF_REG_2);
  outb(IDMRC | QTE | CDB10 | FSCSI | FCLK, base + CONF_REG_3);
  outb(0x83 | EAN, base + CONF_REG_4);
  outb(IE | WSE0, base + CONF_REG_5);
  outb(0, base + FEATURE_EN);
  }
 
static int sym53c416_probeirq(int base, int scsi_id)
  {
  int irq, irqs, i;
 
  /* Clear interrupt register */
  inb(base + INT_REG);
  /* Start probing for irq's */
  irqs = probe_irq_on();
  /* Reinit chip */
  sym53c416_init(base, scsi_id);
  /* Cause interrupt */
  outb(NOOP, base + COMMAND_REG);
  outb(ILLEGAL, base + COMMAND_REG);
  outb(0x07, base + DEST_BUS_ID);
  outb(0x00, base + DEST_BUS_ID);
  /* Wait for interrupt to occur */
  i = jiffies + 20;
  while(i > jiffies && !(inb(base + STATUS_REG) & SCI))
    barrier();
  if(i <= jiffies) /* timed out */
    return 0;
  /* Get occurred irq */
  irq = probe_irq_off(irqs);
  sym53c416_init(base, scsi_id);
  return irq;
  }
 
/* Setup: sym53c416=base,irq */
void sym53c416_setup(char *str, int *ints)
  {
  int i;
 
  if(host_index >= MAXHOSTS)
    {
    printk("sym53c416.c: Too many hosts defined\n");
    }
  else
    {
    if(ints[0] < 1 || ints[0] > 2)
      {
      printk("sym53c416.c: Wrong number of parameters:\n");
      printk("sym53c416.c: usage: sym53c416=<base>[,<irq>]\n");
      }
    else
      {
      for(i = 0; i < host_index && i >= 0; i++)
        if(hosts[i].base == ints[1])
          i = -2;
      if(i >= 0)
        {
        hosts[host_index].base = ints[1];
        hosts[host_index].irq = (ints[0] == 2)? ints[2] : 0;
        host_index++;
        }
      }
    }
  }
 
static int sym53c416_test(int base)
  {
  outb(RESET_CHIP, base + COMMAND_REG);
  outb(NOOP, base + COMMAND_REG);
  if(inb(base + COMMAND_REG) != NOOP)
    return 0;
  if(!inb(base + TC_HIGH) || inb(base + TC_HIGH) == 0xFF)
    return 0;
  if((inb(base + PIO_INT_REG) & (FULL | EMPTY | CE | OUE | FIE | EIE)) != EMPTY)
    return 0;
  return 1;
  }
 
void sym53c416_probe(void)
  {
  int *base = probeaddrs;
  int ints[2];
 
  ints[0] = 1;
  for(; *base; base++)
    if(!check_region(*base, IO_RANGE) && sym53c416_test(*base))
      {
      ints[1] = *base;
      sym53c416_setup(NULL, ints);
      }
  }
 
int sym53c416_detect(Scsi_Host_Template *tpnt)
  {
  unsigned long flags;
  struct Scsi_Host * shpnt = NULL;
  int i;
  int count;
 
#ifdef MODULE
  int ints[3];
 
  ints[0] = 2;
  if(sym53c416_base)
    {
    ints[1] = sym53c416_base;
    ints[2] = sym53c416_irq;
    sym53c416_setup(NULL, ints);
    }
  if(sym53c416_base_1)
    {
    ints[1] = sym53c416_base_1;
    ints[2] = sym53c416_irq_1;
    sym53c416_setup(NULL, ints);
    }
  if(sym53c416_base_2)
    {
    ints[1] = sym53c416_base_2;
    ints[2] = sym53c416_irq_2;
    sym53c416_setup(NULL, ints);
    }
  if(sym53c416_base_3)
    {
    ints[1] = sym53c416_base_3;
    ints[2] = sym53c416_irq_3;
    sym53c416_setup(NULL, ints);
    }
#endif
 
  printk("sym53c416.c: %s\n", VERSION_STRING);
 
  sym53c416_probe();
 
  /* Now we register and set up each host adapter found... */
  for(count = 0, i = 0; i < host_index; i++)
    if(!sym53c416_test(hosts[i].base))
      printk("No sym53c416 found at address 0x%03x\n", hosts[i].base);
    else
      {
      if(hosts[i].irq == 0)
        /* We don't have an irq yet, so we should probe for one */
        if((hosts[i].irq = sym53c416_probeirq(hosts[i].base, hosts[i].scsi_id)) == 0)
          printk("irq autoprobing failed for sym53c416 at address 0x%03x\n", hosts[i].base);
      if(hosts[i].irq && !check_region(hosts[i].base, IO_RANGE))
        {
        shpnt = scsi_register(tpnt, 0);
        save_flags(flags);
        cli();
        /* Request for specified IRQ */
        if(request_irq(hosts[i].irq, sym53c416_intr_handle, 0, ID, NULL))
          {
          restore_flags(flags);
          printk("Unable to assign IRQ %d\n", hosts[i].irq);
          scsi_unregister(shpnt);
          }
        else
          {
          /* Inform the kernel of our IO range */
          request_region(hosts[i].base, IO_RANGE, ID);
          shpnt->unique_id = hosts[i].base;
          shpnt->io_port = hosts[i].base;
          shpnt->n_io_port = IO_RANGE;
          shpnt->irq = hosts[i].irq;
          shpnt->this_id = hosts[i].scsi_id;
          sym53c416_init(hosts[i].base, hosts[i].scsi_id);
          count++;
          restore_flags(flags);
          }
        }
      }
  return count;
  }
 
const char *sym53c416_info(struct Scsi_Host *SChost)
  {
  int i;
  int base = SChost->io_port;
  int irq = SChost->irq;
  int scsi_id = 0;
  int rev = inb(base + TC_HIGH);
 
  for(i = 0; i < host_index; i++)
    if(hosts[i].base == base)
      scsi_id = hosts[i].scsi_id;
  sprintf(info, "Symbios Logic 53c416 (rev. %d) at 0x%03x, irq %d, SCSI-ID %d, %s pio", rev, base, irq, scsi_id, (fastpio)? "fast" : "slow");
  return info;
  }
 
int sym53c416_queuecommand(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *))
  {
  int base;
  unsigned long flags = 0;
  int i;
 
  /* Store base register as we can have more than one controller in the system */
  base = SCpnt->host->io_port;
  current_command = SCpnt;                  /* set current command                */
  current_command->scsi_done = done;        /* set ptr to done function           */
  current_command->SCp.phase = command_ph;  /* currect phase is the command phase */
  current_command->SCp.Status = 0;
  current_command->SCp.Message = 0;
 
  save_flags(flags);
  cli();
  outb(SCpnt->target, base + DEST_BUS_ID); /* Set scsi id target        */
  outb(FLUSH_FIFO, base + COMMAND_REG);    /* Flush SCSI and PIO FIFO's */
  /* Write SCSI command into the SCSI fifo */
  for(i = 0; i < SCpnt->cmd_len; i++)
    outb(SCpnt->cmnd[i], base + SCSI_FIFO);
  /* Start selection sequence */
  outb(SEL_WITHOUT_ATN_SEQ, base + COMMAND_REG);
  /* Now an interrupt will be generated which we will catch in out interrupt routine */
  restore_flags(flags);
  return 0;
  }
 
static void internal_done(Scsi_Cmnd *SCpnt)
  {
  SCpnt->SCp.Status++;
  }
 
int sym53c416_command(Scsi_Cmnd *SCpnt)
  {
  sym53c416_queuecommand(SCpnt, internal_done);
  SCpnt->SCp.Status = 0;
  while(!SCpnt->SCp.Status)
    barrier();
  return SCpnt->result;
  }
 
int sym53c416_abort(Scsi_Cmnd *SCpnt)
  {
  printk("sym53c416_abort\n");
 
  /* We don't know how to abort for the moment */
  return SCSI_ABORT_SNOOZE;
  }
 
int sym53c416_reset(Scsi_Cmnd *SCpnt, unsigned int reset_flags)
  {
  int base;
  int scsi_id = -1;
  int i;
 
  printk("sym53c416_reset\n");
  base = SCpnt->host->io_port;
  /* search scsi_id */
  for(i = 0; i < host_index && scsi_id != -1; i++)
    if(hosts[i].base == base)
      scsi_id = hosts[i].scsi_id;
  outb(RESET_CHIP, base + COMMAND_REG);
  outb(NOOP | PIO_MODE, base + COMMAND_REG);
  outb(RESET_SCSI_BUS, base + COMMAND_REG);
  sym53c416_init(base, scsi_id);
  return SCSI_RESET_PENDING;
  }
 
int sym53c416_bios_param(Disk *disk, kdev_t dev, int *ip)
  {
  int size;
 
  size = disk->capacity;
  ip[0] = 64;                         /* heads                        */
  ip[1] = 32;                         /* sectors                      */
  if((ip[2] = size >> 11) > 1024)     /* cylinders, test for big disk */
    {
    ip[0] = 255;                      /* heads                        */
    ip[1] = 63;                       /* sectors                      */
    ip[2] = size / (255 * 63);        /* cylinders                    */
    }
  return 0;
  }
 
/* Loadable module support */
#ifdef MODULE
 
#if LINUX_VERSION_CODE >= LinuxVersionCode(2,1,26)
MODULE_AUTHOR("Lieven Willems");
MODULE_PARM(sym53c416, "1-2i");
MODULE_PARM(sym53c416_1, "1-2i");
MODULE_PARM(sym53c416_2, "1-2i");
MODULE_PARM(sym53c416_3, "1-2i");
#endif
 
Scsi_Host_Template driver_template = SYM53C416;
 
#include "scsi_module.c"
#endif