Subversion Repositories or1k

/*-------------------------------------------------------------------------+
| ldsegs.s v1.1 - PC386 BSP - 1997/08/07
+--------------------------------------------------------------------------+
| This file assists the board independent startup code by loading the proper
| segment register values. The values loaded are board dependent. In addition
| it contains code to enable the A20 line and to reprogram the PIC to relocate
| the IRQ interrupt vectors to 0x20 -> 0x2f.
| NOTE: No stack has been established when this routine is invoked.
|       It returns by jumping back to bspentry.
+--------------------------------------------------------------------------+
| (C) Copyright 1997 -
| - NavIST Group - Real-Time Distributed Systems and Industrial Automation
|
| http://pandora.ist.utl.pt
|
| Instituto Superior Tecnico * Lisboa * PORTUGAL
+--------------------------------------------------------------------------+
| Disclaimer:
|
| This file is provided "AS IS" without warranty of any kind, either
| expressed or implied.
+--------------------------------------------------------------------------+
| This code is base on:
|   ldsegs.s,v 1.4 1996/04/20 16:48:30 joel Exp - go32 BSP
| With the following copyright notice:
| **************************************************************************
| *  COPYRIGHT (c) 1989-1999.
| *  On-Line Applications Research Corporation (OAR).
| *
| *  The license and distribution terms for this file may be
| *  found in found in the file LICENSE in this distribution or at
| *  http://www.OARcorp.com/rtems/license.html.
| **************************************************************************
|
|  ldsegs.S,v 1.11 2002/07/30 16:24:03 ralf Exp
+--------------------------------------------------------------------------*/

#include <asm.h>

/*----------------------------------------------------------------------------+
| CODE section
+----------------------------------------------------------------------------*/
EXTERN (rtems_i8259_masks)
        
BEGIN_CODE

        EXTERN (_establish_stack)
        EXTERN (Timer_exit)
        EXTERN (clockOff)

/*----------------------------------------------------------------------------+
| pc386_delay
+------------------------------------------------------------------------------
| Delay is needed after doing I/O. 
|
| The outb version is OK on most machines BUT the loop version ...
| 
| will delay for 1us on 1Gz machine, it will take a little bit
| longer on slower machines, however, it does not matter because we
| are going to call this function only a few times

+----------------------------------------------------------------------------*/
#define DELAY_USE_OUTB
        
        .p2align 4
        .globl _pc386_delay
        .globl pc386_delay
pc386_delay:
_pc386_delay:
#ifdef  DELAY_USE_OUTB
        outb    al, $0x80       # about 1uS delay on most machines
#else
        movl    $0x200, eax
pc386_delay1:
        dec     eax
        jnz     pc386_delay1
#endif
        ret

/*-------------------------------------------------------------------------+
|         Function: _load_segments
|      Description: Current environment is standard PC booted by grub.
|                   So, there is no value in saving current GDT and IDT
|                   settings we have to set it up ourseves. (Naturally
|                   it will be not so in case we are booted by some
|                   boot monitor, however, then it will be different
|                   BSP). After that we have to load board segment registers
|                   with apropriate values +  reprogram PIC.
| Global Variables: None.
|        Arguments: None.
|          Returns: Nothing. 
+--------------------------------------------------------------------------*/
        .p2align 4
        
        PUBLIC (_load_segments)
SYM (_load_segments):

        lgdt SYM(gdtdesc)
        lidt SYM(idtdesc)

        /* Load CS, flush prefetched queue */
        ljmp $0x8, $next_step

next_step:      
        /* Load segment registers */
        movw $0x10, ax
        movw ax, ss
        movw ax, ds
        movw ax, es
        movw ax, fs
        movw ax, gs

/*---------------------------------------------------------------------+
| Now we have to reprogram the interrupts :-(. We put them right after
| the intel-reserved hardware interrupts, at int 0x20-0x2F. There they
| won't mess up anything. Sadly IBM really messed this up with the
| original PC, and they haven't been able to rectify it afterwards. Thus
| the bios puts interrupts at 0x08-0x0f, which is used for the internal
| hardware interrupts as well. We just have to reprogram the 8259's, and
| it isn't fun.
+---------------------------------------------------------------------*/

        movb    $0x11, al               /* initialization sequence          */
        outb    al, $0x20               /* send it to 8259A-1               */
        call    SYM(pc386_delay)
        outb    al, $0xA0               /* and to 8259A-2                   */
        call    SYM(pc386_delay)
        
        movb    $0x20, al               /* start of hardware int's (0x20)   */
        outb    al, $0x21
        call    SYM(pc386_delay)
        movb    $0x28, al               /* start of hardware int's 2 (0x28) */
        outb    al, $0xA1
        call    SYM(pc386_delay)
        
        movb    $0x04, al               /* 8259-1 is master                 */
        outb    al, $0x21
        call    SYM(pc386_delay)
        movb    $0x02, al               /* 8259-2 is slave                  */
        outb    al, $0xA1
        call    SYM(pc386_delay)
        
        movb    $0x01, al               /* 8086 mode for both               */
        outb    al, $0x21
        call    SYM(pc386_delay)
        outb    al, $0xA1
        call    SYM(pc386_delay)
        
        movb    $0xFF, al               /* mask off all interrupts for now  */
        outb    al, $0xA1
        call    SYM(pc386_delay)
        movb    $0xFB, al               /* mask all irq's but irq2 which    */
        outb    al, $0x21               /* is cascaded                      */
        call    SYM(pc386_delay)

        movw    $0xFFFB, SYM(i8259s_cache) /* set up same values in cache */
        
        jmp     SYM (_establish_stack)  # return to the bsp entry code

/*-------------------------------------------------------------------------+
|         Function: _return_to_monitor
|      Description: Return to board's monitor (we have none so simply restart).
| Global Variables: None.
|        Arguments: None.
|          Returns: Nothing. 
+--------------------------------------------------------------------------*/

        .p2align 4
        
        PUBLIC (_return_to_monitor)
SYM (_return_to_monitor):

        call    SYM (Timer_exit)
        call    SYM (Clock_exit)
        jmp     SYM (start)

/*-------------------------------------------------------------------------+
|         Function: _default_int_handler
|      Description: default interrupt handler
| Global Variables: None.
|        Arguments: None.
|          Returns: Nothing. 
+--------------------------------------------------------------------------*/
        .p2align 4
        
/*---------------------------------------------------------------------------+
| GDT itself
+--------------------------------------------------------------------------*/

        .p2align 4
                
        PUBLIC (_Global_descriptor_table)
SYM (_Global_descriptor_table):

        /* NULL segment */
        .word 0, 0     
        .byte 0, 0, 0, 0

        /* code segment */
        .word 0xffff, 0
        .byte 0, 0x9e, 0xcf, 0

        /* data segment */
        .word 0xffff, 0
        .byte 0, 0x92, 0xcf, 0
 

/*---------------------------------------------------------------------------+
| Descriptor of GDT
+--------------------------------------------------------------------------*/
SYM (gdtdesc):
        .word (3*8 - 1)  
        .long SYM (_Global_descriptor_table)


/*---------------------------------------------------------------------------+
| IDT itself
+---------------------------------------------------------------------------*/
        .p2align 4
        
        PUBLIC(Interrupt_descriptor_table)
SYM(Interrupt_descriptor_table):
        .rept 256
        .word 0,0,0,0
        .endr
        
/*---------------------------------------------------------------------------+
| Descriptor of IDT
+--------------------------------------------------------------------------*/
SYM(idtdesc):   
        .word  (256*8 - 1)
        .long  SYM (Interrupt_descriptor_table)
        
END_CODE

    .section .m_hdr
        .long 0x1BADB002
        .long 0
        .long 0xE4524FFE
END