URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [uclinux/] [uClinux-2.0.x/] [arch/] [m68knommu/] [config.in] - Rev 1775
Go to most recent revision | Compare with Previous | Blame | View Log
#
# For a description of the syntax of this configuration file,
# see the Configure script.
#
mainmenu_name 'uClinux/68k (w/o MMU) Kernel Configuration'
define_bool CONFIG_UCLINUX y
mainmenu_option next_comment
comment 'Code maturity level options'
bool 'Prompt for development and/or incomplete code/drivers' CONFIG_EXPERIMENTAL
endmenu
# mainmenu_option next_comment
# comment 'Loadable module support'
# bool 'Enable loadable module support' CONFIG_MODULES
# if [ "$CONFIG_MODULES" = "y" ]; then
# bool 'Set version information on all symbols for modules' CONFIG_MODVERSIONS
# bool 'Kernel daemon support (e.g. autoload of modules)' CONFIG_KERNELD
# fi
# endmenu
mainmenu_option next_comment
comment 'Platform dependant setup'
choice 'CPU' \
"MC68000 CONFIG_M68000 \
MC68EN302 CONFIG_M68EN302 \
MC68328 CONFIG_M68328 \
MC68EZ328 CONFIG_M68EZ328 \
MC68332 CONFIG_M68332 \
MC68360 CONFIG_M68360 \
MCF5206 CONFIG_M5206 \
MCF5206e CONFIG_M5206e \
MCF5307 CONFIG_M5307 \
MCF5204 CONFIG_M5204" M68EZ328
comment 'Platform'
if [ "$CONFIG_M68328" = "y" ]; then
bool 'Pilot 1000/5000, PalmPilot Personal/Pro, or PalmIII support' CONFIG_PILOT
if [ "$CONFIG_PILOT" = "y" ]; then
bool '(X)Copilot support' CONFIG_XCOPILOT_BUGS
fi
fi
if [ "$CONFIG_M68EZ328" = "y" ]; then
bool 'Motorola M68EZ328ADS Dev. Board support' CONFIG_M68EZ328ADS
if [ "$CONFIG_M68EZ328ADS" = "y" ]; then
bool 'Compile the kernel to be loaded in DRAM instead of FLASH' CONFIG_M68EZ328ADS_RAM
fi
bool 'ALMA Electronics board support' CONFIG_ALMA_ANS
if [ "$CONFIG_ALMA_ANS" = "y" ]; then
bool 'Compile the kernel to be loaded in DRAM instead of FLASH' CONFIG_ALMA_ANS_RAM
fi
bool 'uCsimm module support' CONFIG_UCSIMM
bool 'PalmV support' CONFIG_PILOT
fi
if [ "$CONFIG_M68EN302" = "y" ]; then
choice 'CLOCK' \
"CLOCK_20MHz CONFIG_CLOCK_20MHz \
CLOCK_25MHz CONFIG_CLOCK_25MHz" CLOCK_25MHz
bool 'Aplio/Pro or Aplio/Entrecote support' CONFIG_APLIO
if [ "$CONFIG_APLIO" = "y" ]; then
bool 'Aplio Pro' CONFIG_APLIO_PRO
bool 'Aplio Entrecote' CONFIG_APLIO_ENTRECOTE
fi
fi
if [ "$CONFIG_M68332" = "y" ]; then
bool 'SHGLCore support' CONFIG_SHGLCORE
if [ "$CONFIG_SHGLCORE" = "y" ]; then
bool '2Meg SHGLCore' CONFIG_SHGLCORE_2MEG
fi
fi
if [ "$CONFIG_M5204" = "y" ]; then
define_bool CONFIG_COLDFIRE y
fi
if [ "$CONFIG_M5206" = "y" ]; then
define_bool CONFIG_COLDFIRE y
bool 'Arnewsh 5206 eval board support' CONFIG_ARNEWSH
fi
if [ "$CONFIG_M5206e" = "y" ]; then
define_bool CONFIG_COLDFIRE y
bool 'Cadre-III support' CONFIG_CADRE3
bool 'eLITE-5206e support' CONFIG_ELITE
if [ "$CONFIG_ELITE" = "y" ]; then
bool ' SRAM only eLITE-5206e support' CONFIG_SMALL
fi
bool 'Moreton Bay NETtel 1500 support' CONFIG_NETtel
bool 'Telos Omnia ToolVox support' CONFIG_TELOS
fi
if [ "$CONFIG_M5307" = "y" ]; then
define_bool CONFIG_COLDFIRE y
bool 'Arnewsh 5307 eval board support' CONFIG_ARNEWSH
bool 'Moreton Bay NETtel support' CONFIG_NETtel
bool 'Moreton Bay eLIA development board support' CONFIG_eLIA
bool 'Moreton Bay MATtel support' CONFIG_MATtel
bool 'Cadre-III eval board support' CONFIG_CADRE3
bool 'Old mask (broken watchdog timer)' CONFIG_OLDMASK
fi
choice 'Kernel executes from' \
"RAM CONFIG_RAMKERNEL \
ROM CONFIG_ROMKERNEL" ROM
endmenu
mainmenu_option next_comment
comment 'General setup'
bool 'PCI bios support' CONFIG_PCI
if [ "$CONFIG_PCI" = "y" ]; then
bool ' PCI device list support' CONFIG_PCIDEVLIST
fi
bool 'Networking support' CONFIG_NET
bool 'System V IPC' CONFIG_SYSVIPC
bool 'Reduced memory footprint' CONFIG_REDUCED_MEMORY
tristate 'Kernel support for flat binaries' CONFIG_BINFMT_FLAT
# tristate 'Kernel support for a.out binaries' CONFIG_BINFMT_AOUT
# tristate 'Kernel support for ELF binaries' CONFIG_BINFMT_ELF
bool 'Compile kernel as ELF - if your GCC is ELF-GCC' CONFIG_KERNEL_ELF
if [ "$CONFIG_PILOT" = "y" ]; then
bool 'Display memory usage on Pilot screen' CONFIG_PILOT_MEMORY_DISPLAY
fi
bool 'Console support' CONFIG_CONSOLE
if [ "$CONFIG_CONSOLE" = "y" ]; then
bool 'Frame buffer' CONFIG_FRAMEBUFFER
if [ "$CONFIG_PILOT" = "y" -a "$CONFIG_FRAMEBUFFER" = "y" ]; then
bool 'Pilot console' CONFIG_PILOT_CONSOLE
fi
fi
endmenu
#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Floppy, IDE, and other block devices'
tristate 'ROM disk memory block device' CONFIG_BLK_DEV_BLKMEM
# tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
bool 'IDE harddisk support' CONFIG_BLK_DEV_IDE
if [ "$CONFIG_BLK_DEV_IDE" = "y" ]; then
bool ' Include IDE/ATAPI CDROM support' CONFIG_BLK_DEV_IDECD
bool ' Include IDE/ATAPI TAPE support' CONFIG_BLK_DEV_IDETAPE
bool ' Include IDE/ATAPI FLOPPY support (new)' CONFIG_BLK_DEV_IDEFLOPPY
fi
comment 'Additional Block/FLASH Devices'
tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
bool 'Multiple devices driver support' CONFIG_BLK_DEV_MD
if [ "$CONFIG_BLK_DEV_MD" = "y" ]; then
tristate ' Linear (append) mode' CONFIG_MD_LINEAR
tristate ' RAID-0 (striping) mode' CONFIG_MD_STRIPED
fi
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" ]; then
bool ' Release empty RAM disk blocks' CONFIG_RD_RELEASE_BLOCKS
# bool ' Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD
fi
tristate 'FLASH device support' CONFIG_DEV_FLASH
if [ "$CONFIG_DEV_FLASH" = "y" ]; then
bool ' FLASH Block device' CONFIG_BLK_DEV_FLASH
bool ' FLASH Character device' CONFIG_CHR_DEV_FLASH
fi
endmenu
if [ "$CONFIG_NET" = "y" ]; then
source net/Config.in
fi
if [ "$CONFIG_NET" = "y" ]; then
mainmenu_option next_comment
comment 'Network device support'
bool 'Network device support' CONFIG_NETDEVICES
if [ "$CONFIG_NETDEVICES" = "y" ]; then
#
# Network device configuration
#
tristate 'Dummy net driver support' CONFIG_DUMMY
tristate 'SLIP (serial line) support' CONFIG_SLIP
if [ "$CONFIG_SLIP" != "n" ]; then
bool ' CSLIP compressed headers' CONFIG_SLIP_COMPRESSED
bool ' Keepalive and linefill' CONFIG_SLIP_SMART
bool ' Six bit SLIP encapsulation' CONFIG_SLIP_MODE_SLIP6
fi
tristate 'PPP (point-to-point) support' CONFIG_PPP
if [ ! "$CONFIG_PPP" = "n" ]; then
comment 'CCP compressors for PPP are only built as modules.'
fi
tristate 'EQL (serial line load balancing) support' CONFIG_EQUALIZER
bool 'Cirrus Logic cs8900 ethernet' CONFIG_UCCS8900
if [ "$CONFIG_UCCS8900" != "n" ]; then
bool 'Hardware byte-swapping support for cs8900 ethernet' CONFIG_UCCS8900_HW_SWAP
fi
bool 'SMC 9194 ethernet' CONFIG_SMC9194
bool 'NE2000/NE1000 ISA ethernet' CONFIG_NE2000
if [ "$CONFIG_M68EN302" = "y" ]; then
bool 'MC68EN302 SCC ethernet' CONFIG_M68EN302_ETHERNET
fi
fi
endmenu
fi
source fs/Config.in
mainmenu_option next_comment
comment 'Character devices'
# tristate 'Parallel printer support' CONFIG_PRINTER
# bool 'Support for user misc device modules' CONFIG_UMISC
if [ "$CONFIG_M68328" = "y" ]; then
bool '68328 serial support' CONFIG_68328_SERIAL
if [ "$CONFIG_68328_SERIAL" = "y" ]; then
bool 'Support RTS/CTS on 68328 serial support' CONFIG_68328_SERIAL_RTS_CTS
fi
if [ "$CONFIG_PILOT" = "y" ]; then
bool '68328 digitizer support' CONFIG_68328_DIGI
fi
fi
if [ "$CONFIG_M68EZ328" = "y" ]; then
bool '68328 serial support' CONFIG_68328_SERIAL
if [ "$CONFIG_68328_SERIAL" = "y" ]; then
bool 'Support RTS/CTS on 68328 serial support' CONFIG_68328_SERIAL_RTS_CTS
fi
if [ "$CONFIG_M68EZ328ADS" = "y" ]; then
bool '68681 serial support' CONFIG_68681_SERIAL
fi
fi
if [ "$CONFIG_M68332" = "y" ]; then
bool '68332 serial support' CONFIG_68332_SERIAL
fi
if [ "$CONFIG_M68EN302" = "y" ]; then
bool '68302 serial support' CONFIG_68302_SERIAL
fi
if [ "$CONFIG_COLDFIRE" = "y" ]; then
bool 'ColdFire serial support' CONFIG_COLDFIRE_SERIAL
bool '16550 serial support' CONFIG_SERIAL
bool 'ColdFire MBUS Support' CONFIG_MCF_MBUS
bool 'Support for TEXT based LCD driver' CONFIG_LCDTXT
bool 'Support for ColdFire DMA driven LCD driver' CONFIG_LCDDMA
bool 'Support for ColdFire DMA driven DAC0800 driver' CONFIG_DAC0800
bool 'Support for ColdFire DMA driven I2S DAC driver' CONFIG_DACI2S
bool 'Support for ColdFire T6963 driver' CONFIG_T6963
if [ "$CONFIG_T6963" = "y" ]; then
bool ' Use PIO mode' CONFIG_T6963_PIO
if [ "$CONFIG_T6963_PIO" != "y" ]; then
define_bool CONFIG_T6963_DMA y
fi
fi
fi
# bool 'Support for user serial device modules' CONFIG_USERIAL
bool 'Watchdog Timer Support' CONFIG_WATCHDOG
# if [ "$CONFIG_WATCHDOG" != "n" ]; then
# bool ' Disable watchdog shutdown on close' CONFIG_WATCHDOG_NOWAYOUT
# bool ' Software Watchdog' CONFIG_SOFT_WATCHDOG
# fi
endmenu
# mainmenu_option next_comment
# comment 'Sound support'
#
# tristate 'Sound support' CONFIG_SOUND
# endmenu
mainmenu_option next_comment
comment 'Kernel hacking'
# bool 'Debug kmalloc/kfree' CONFIG_DEBUG_MALLOC
bool 'Kernel profiling support' CONFIG_PROFILE
if [ "$CONFIG_PROFILE" = "y" ]; then
int ' Profile shift count' CONFIG_PROFILE_SHIFT 2
fi
if [ "$CONFIG_COLDFIRE" = "y" ]; then
bool 'Magic SysRq Key' CONFIG_MAGIC_SYSRQ
bool 'Panic/Dump to FLASH' CONFIG_DUMPTOFLASH
fi
endmenu
Go to most recent revision | Compare with Previous | Blame | View Log