URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [uclinux/] [uClinux-2.0.x/] [drivers/] [net/] [hp100.h] - Rev 1765
Compare with Previous | Blame | View Log
/* * hp100.h: Hewlett Packard HP10/100VG ANY LAN ethernet driver for Linux. * * $Id: hp100.h,v 1.1.1.1 2001-09-10 07:44:24 simons Exp $ * * Authors: Jaroslav Kysela, <perex@pf.jcu.cz> * Siegfried Loeffler <floeff@tunix.mathematik.uni-stuttgart.de> * * This driver is based on the 'hpfepkt' crynwr packet driver. * * This source/code is public free; you can distribute it and/or modify * it under terms of the GNU General Public License (published by the * Free Software Foundation) either version two of this License, or any * later version. */ /**************************************************************************** * Hardware Constants ****************************************************************************/ /* * Page Identifiers * (Swap Paging Register, PAGING, bits 3:0, Offset 0x02) */ #define HP100_PAGE_PERFORMANCE 0x0 /* Page 0 */ #define HP100_PAGE_MAC_ADDRESS 0x1 /* Page 1 */ #define HP100_PAGE_HW_MAP 0x2 /* Page 2 */ #define HP100_PAGE_EEPROM_CTRL 0x3 /* Page 3 */ #define HP100_PAGE_MAC_CTRL 0x4 /* Page 4 */ #define HP100_PAGE_MMU_CFG 0x5 /* Page 5 */ #define HP100_PAGE_ID_MAC_ADDR 0x6 /* Page 6 */ #define HP100_PAGE_MMU_POINTER 0x7 /* Page 7 */ /* Registers that are present on all pages */ #define HP100_REG_HW_ID 0x00 /* R: (16) Unique card ID */ #define HP100_REG_TRACE 0x00 /* W: (16) Used for debug output */ #define HP100_REG_PAGING 0x02 /* R: (16),15:4 Card ID */ /* W: (16),3:0 Switch pages */ #define HP100_REG_OPTION_LSW 0x04 /* RW: (16) Select card functions */ #define HP100_REG_OPTION_MSW 0x06 /* RW: (16) Select card functions */ /* Page 0 - Performance */ #define HP100_REG_IRQ_STATUS 0x08 /* RW: (16) Which ints are pending */ #define HP100_REG_IRQ_MASK 0x0a /* RW: (16) Select ints to allow */ #define HP100_REG_FRAGMENT_LEN 0x0c /* W: (16)12:0 Current fragment len */ /* Note: For 32 bit systems, fragment len and offset registers are available */ /* at offset 0x28 and 0x2c, where they can be written as 32bit values. */ #define HP100_REG_OFFSET 0x0e /* RW: (16)12:0 Offset to start read */ #define HP100_REG_DATA32 0x10 /* RW: (32) I/O mode data port */ #define HP100_REG_DATA16 0x12 /* RW: WORDs must be read from here */ #define HP100_REG_TX_MEM_FREE 0x14 /* RD: (32) Amount of free Tx mem */ #define HP100_REG_TX_PDA_L 0x14 /* W: (32) BM: Ptr to PDL, Low Pri */ #define HP100_REG_TX_PDA_H 0x1c /* W: (32) BM: Ptr to PDL, High Pri */ #define HP100_REG_RX_PKT_CNT 0x18 /* RD: (8) Rx count of pkts on card */ #define HP100_REG_TX_PKT_CNT 0x19 /* RD: (8) Tx count of pkts on card */ #define HP100_REG_RX_PDL 0x1a /* R: (8) BM: # rx pdl not executed */ #define HP100_REG_TX_PDL 0x1b /* R: (8) BM: # tx pdl not executed */ #define HP100_REG_RX_PDA 0x18 /* W: (32) BM: Up to 31 addresses */ /* which point to a PDL */ #define HP100_REG_SL_EARLY 0x1c /* (32) Enhanced Slave Early Rx */ #define HP100_REG_STAT_DROPPED 0x20 /* R (12) Dropped Packet Counter */ #define HP100_REG_STAT_ERRORED 0x22 /* R (8) Errored Packet Counter */ #define HP100_REG_STAT_ABORT 0x23 /* R (8) Abort Counter/OW Coll. Flag */ #define HP100_REG_RX_RING 0x24 /* W (32) Slave: RX Ring Pointers */ #define HP100_REG_32_FRAGMENT_LEN 0x28 /* W (13) Slave: Fragment Length Reg */ #define HP100_REG_32_OFFSET 0x2c /* W (16) Slave: Offset Register */ /* Page 1 - MAC Address/Hash Table */ #define HP100_REG_MAC_ADDR 0x08 /* RW: (8) Cards MAC address */ #define HP100_REG_HASH_BYTE0 0x10 /* RW: (8) Cards multicast filter */ /* Page 2 - Hardware Mapping */ #define HP100_REG_MEM_MAP_LSW 0x08 /* RW: (16) LSW of cards mem addr */ #define HP100_REG_MEM_MAP_MSW 0x0a /* RW: (16) MSW of cards mem addr */ #define HP100_REG_IO_MAP 0x0c /* RW: (8) Cards I/O address */ #define HP100_REG_IRQ_CHANNEL 0x0d /* RW: (8) IRQ and edge/level int */ #define HP100_REG_SRAM 0x0e /* RW: (8) How much RAM on card */ #define HP100_REG_BM 0x0f /* RW: (8) Controls BM functions */ /* New on Page 2 for ETR chips: */ #define HP100_REG_MODECTRL1 0x10 /* RW: (8) Mode Control 1 */ #define HP100_REG_MODECTRL2 0x11 /* RW: (8) Mode Control 2 */ #define HP100_REG_PCICTRL1 0x12 /* RW: (8) PCI Cfg 1 */ #define HP100_REG_PCICTRL2 0x13 /* RW: (8) PCI Cfg 2 */ #define HP100_REG_PCIBUSMLAT 0x15 /* RW: (8) PCI Bus Master Latency */ #define HP100_REG_EARLYTXCFG 0x16 /* RW: (16) Early TX Cfg/Cntrl Reg */ #define HP100_REG_EARLYRXCFG 0x18 /* RW: (8) Early RX Cfg/Cntrl Reg */ #define HP100_REG_ISAPNPCFG1 0x1a /* RW: (8) ISA PnP Cfg/Cntrl Reg 1 */ #define HP100_REG_ISAPNPCFG2 0x1b /* RW: (8) ISA PnP Cfg/Cntrl Reg 2 */ /* Page 3 - EEPROM/Boot ROM */ #define HP100_REG_EEPROM_CTRL 0x08 /* RW: (16) Used to load EEPROM */ #define HP100_REG_BOOTROM_CTRL 0x0a /* Page 4 - LAN Configuration (MAC_CTRL) */ #define HP100_REG_10_LAN_CFG_1 0x08 /* RW: (8) Set 10M XCVR functions */ #define HP100_REG_10_LAN_CFG_2 0x09 /* RW: (8) 10M XCVR functions */ #define HP100_REG_VG_LAN_CFG_1 0x0a /* RW: (8) Set 100M XCVR functions */ #define HP100_REG_VG_LAN_CFG_2 0x0b /* RW: (8) 100M LAN Training cfgregs */ #define HP100_REG_MAC_CFG_1 0x0c /* RW: (8) Types of pkts to accept */ #define HP100_REG_MAC_CFG_2 0x0d /* RW: (8) Misc MAC functions */ #define HP100_REG_MAC_CFG_3 0x0e /* RW: (8) Misc MAC functions */ #define HP100_REG_MAC_CFG_4 0x0f /* R: (8) Misc MAC states */ #define HP100_REG_DROPPED 0x10 /* R: (16),11:0 Pkts cant fit in mem*/ #define HP100_REG_CRC 0x12 /* R: (8) Pkts with CRC */ #define HP100_REG_ABORT 0x13 /* R: (8) Aborted Tx pkts */ #define HP100_REG_TRAIN_REQUEST 0x14 /* RW: (16) Endnode MAC register.*/ #define HP100_REG_TRAIN_ALLOW 0x16 /* R: (16) Hub allowed register */ /* Page 5 - MMU */ #define HP100_REG_RX_MEM_STOP 0x0c /* RW: (16) End of Rx ring addr */ #define HP100_REG_TX_MEM_STOP 0x0e /* RW: (16) End of Tx ring addr */ #define HP100_REG_PDL_MEM_STOP 0x10 /* Not used by 802.12 devices */ #define HP100_REG_ECB_MEM_STOP 0x14 /* I've no idea what this is */ /* Page 6 - Card ID/Physical LAN Address */ #define HP100_REG_BOARD_ID 0x08 /* R: (8) EISA/ISA card ID */ #define HP100_REG_BOARD_IO_CHCK 0x0c /* R: (8) Added to ID to get FFh */ #define HP100_REG_SOFT_MODEL 0x0d /* R: (8) Config program defined */ #define HP100_REG_LAN_ADDR 0x10 /* R: (8) MAC addr of card */ #define HP100_REG_LAN_ADDR_CHCK 0x16 /* R: (8) Added to addr to get FFh */ /* Page 7 - MMU Current Pointers */ #define HP100_REG_PTR_RXSTART 0x08 /* R: (16) Current begin of Rx ring */ #define HP100_REG_PTR_RXEND 0x0a /* R: (16) Current end of Rx ring */ #define HP100_REG_PTR_TXSTART 0x0c /* R: (16) Current begin of Tx ring */ #define HP100_REG_PTR_TXEND 0x0e /* R: (16) Current end of Rx ring */ #define HP100_REG_PTR_RPDLSTART 0x10 #define HP100_REG_PTR_RPDLEND 0x12 #define HP100_REG_PTR_RINGPTRS 0x14 #define HP100_REG_PTR_MEMDEBUG 0x1a /* ------------------------------------------------------------------------ */ /* * Hardware ID Register I (Always available, HW_ID, Offset 0x00) */ #define HP100_HW_ID_CASCADE 0x4850 /* Identifies Cascade Chip */ /* * Hardware ID Register 2 & Paging Register * (Always available, PAGING, Offset 0x02) * Bits 15:4 are for the Chip ID */ #define HP100_CHIPID_MASK 0xFFF0 #define HP100_CHIPID_SHASTA 0x5350 /* Not 802.12 compliant */ /* EISA BM/SL, MCA16/32 SL, ISA SL */ #define HP100_CHIPID_RAINIER 0x5360 /* Not 802.12 compliant EISA BM,*/ /* PCI SL, MCA16/32 SL, ISA SL */ #define HP100_CHIPID_LASSEN 0x5370 /* 802.12 compliant PCI BM, PCI SL */ /* LRF supported */ /* * Option Registers I and II * (Always available, OPTION_LSW, Offset 0x04-0x05) */ #define HP100_DEBUG_EN 0x8000 /* 0:Dis., 1:Enable Debug Dump Ptr. */ #define HP100_RX_HDR 0x4000 /* 0:Dis., 1:Enable putting pkt into */ /* system mem. before Rx interrupt */ #define HP100_MMAP_DIS 0x2000 /* 0:Enable, 1:Disable mem.mapping. */ /* MMAP_DIS must be 0 and MEM_EN */ /* must be 1 for memory-mapped */ /* mode to be enabled */ #define HP100_EE_EN 0x1000 /* 0:Disable,1:Enable EEPROM writing */ #define HP100_BM_WRITE 0x0800 /* 0:Slave, 1:Bus Master for Tx data */ #define HP100_BM_READ 0x0400 /* 0:Slave, 1:Bus Master for Rx data */ #define HP100_TRI_INT 0x0200 /* 0:Don't, 1:Do tri-state the int */ #define HP100_MEM_EN 0x0040 /* Config program set this to */ /* 0:Disable, 1:Enable mem map. */ /* See MMAP_DIS. */ #define HP100_IO_EN 0x0020 /* 1:Enable I/O transfers */ #define HP100_BOOT_EN 0x0010 /* 1:Enable boot ROM access */ #define HP100_FAKE_INT 0x0008 /* 1:int */ #define HP100_INT_EN 0x0004 /* 1:Enable ints from card */ #define HP100_HW_RST 0x0002 /* 0:Reset, 1:Out of reset */ /* NIC reset on 0 to 1 transition */ /* * Option Register III * (Always available, OPTION_MSW, Offset 0x06) */ #define HP100_PRIORITY_TX 0x0080 /* 1:Do all Tx pkts as priority */ #define HP100_EE_LOAD 0x0040 /* 1:EEPROM loading, 0 when done */ #define HP100_ADV_NXT_PKT 0x0004 /* 1:Advance to next pkt in Rx queue */ /* h/w will set to 0 when done */ #define HP100_TX_CMD 0x0002 /* 1:Tell h/w download done, h/w */ /* will set to 0 when done */ /* * Interrupt Status Registers I and II * (Page PERFORMANCE, IRQ_STATUS, Offset 0x08-0x09) * Note: With old chips, these Registers will clear when 1 is written to them * with new chips this depends on setting of CLR_ISMODE */ #define HP100_RX_EARLY_INT 0x2000 #define HP100_RX_PDA_ZERO 0x1000 #define HP100_RX_PDL_FILL_COMPL 0x0800 #define HP100_RX_PACKET 0x0400 /* 0:No, 1:Yes pkt has been Rx */ #define HP100_RX_ERROR 0x0200 /* 0:No, 1:Yes Rx pkt had error */ #define HP100_TX_PDA_ZERO 0x0020 /* 1 when PDA count goes to zero */ #define HP100_TX_SPACE_AVAIL 0x0010 /* 0:<8192, 1:>=8192 Tx free bytes */ #define HP100_TX_COMPLETE 0x0008 /* 0:No, 1:Yes a Tx has completed */ #define HP100_MISC_ERROR 0x0004 /* 0:No, 1:Lan Link down or bus error*/ #define HP100_TX_ERROR 0x0002 /* 0:No, 1:Yes Tx pkt had error */ /* * Xmit Memory Free Count * (Page PERFORMANCE, TX_MEM_FREE, Offset 0x14) (Read only, 32bit) */ #define HP100_AUTO_COMPARE 0x80000000 /* Tx Space avail & pkts<255 */ #define HP100_FREE_SPACE 0x7fffffe0 /* Tx free memory */ /* * IRQ Channel * (Page HW_MAP, IRQ_CHANNEL, Offset 0x0d) */ #define HP100_ZERO_WAIT_EN 0x80 /* 0:No, 1:Yes asserts NOWS signal */ #define HP100_IRQ_SCRAMBLE 0x40 #define HP100_BOND_HP 0x20 #define HP100_LEVEL_IRQ 0x10 /* 0:Edge, 1:Level type interrupts. */ /* (Only valid on EISA cards) */ #define HP100_IRQMASK 0x0F /* Isolate the IRQ bits */ /* * SRAM Parameters * (Page HW_MAP, SRAM, Offset 0x0e) */ #define HP100_RAM_SIZE_MASK 0xe0 /* AND to get SRAM size index */ #define HP100_RAM_SIZE_SHIFT 0x05 /* Shift count(put index in lwr bits)*/ /* * Bus Master Register * (Page HW_MAP, BM, Offset 0x0f) */ #define HP100_BM_BURST_RD 0x01 /* EISA only: 1=Use burst trans. fm system */ /* memory to chip (tx) */ #define HP100_BM_BURST_WR 0x02 /* EISA only: 1=Use burst trans. fm system */ /* memory to chip (rx) */ #define HP100_BM_MASTER 0x04 /* 0:Slave, 1:BM mode */ #define HP100_BM_PAGE_CK 0x08 /* This bit should be set whenever in*/ /* an EISA system */ #define HP100_BM_PCI_8CLK 0x40 /* ... cycles 8 clocks apart */ /* * Mode Control Register I * (Page HW_MAP, MODECTRL1, Offset0x10) */ #define HP100_TX_DUALQ 0x10 /* If set and BM -> dual tx pda queues*/ #define HP100_ISR_CLRMODE 0x02 /* If set ISR will clear all pending */ /* interrupts on read (etr only?) */ #define HP100_EE_NOLOAD 0x04 /* Status whether res will be loaded */ /* from the eeprom */ #define HP100_TX_CNT_FLG 0x08 /* Controls Early TX Reg Cnt Field */ #define HP100_PDL_USE3 0x10 /* If set BM engine will read only */ /* first three data elements of a PDL */ /* on the first access. */ #define HP100_BUSTYPE_MASK 0xe0 /* Three bit bus type info */ /* * Mode Control Register II * (Page HW_MAP, MODECTRL2, Offset0x11) */ #define HP100_EE_MASK 0x0f /* Tell EEPROM circuit not to load */ /* certain resources */ #define HP100_DIS_CANCEL 0x20 /* For tx dualq mode operation */ #define HP100_EN_PDL_WB 0x40 /* 1: Status of PDL completion may be */ /* written back to system mem */ #define HP100_EN_BUS_FAIL 0x80 /* Enables bus-fail portion of misc */ /* interrupt */ /* * PCI Configuration and Control Register I * (Page HW_MAP, PCICTRL1, Offset 0x12) */ #define HP100_LO_MEM 0x01 /* 1: Mapped Mem requested below 1MB */ #define HP100_NO_MEM 0x02 /* 1: Disables Req for sysmem to PCI */ /* bios */ #define HP100_USE_ISA 0x04 /* 1: isa type decodes will occur */ /* simultaneously with PCI decodes */ #define HP100_IRQ_HI_MASK 0xf0 /* pgmed by pci bios */ #define HP100_PCI_IRQ_HI_MASK 0x78 /* Isolate 4 bits for PCI IRQ */ /* * PCI Configuration and Control Register II * (Page HW_MAP, PCICTRL2, Offset 0x13) */ #define HP100_RD_LINE_PDL 0x01 /* 1: PCI command Memory Read Line en */ #define HP100_RD_TX_DATA_MASK 0x06 /* choose PCI memread cmds for TX */ #define HP100_MWI 0x08 /* 1: en. PCI memory write invalidate */ #define HP100_ARB_MODE 0x10 /* Select PCI arbitor type */ #define HP100_STOP_EN 0x20 /* Enables PCI state machine to issue */ /* pci stop if cascade not ready */ #define HP100_IGNORE_PAR 0x40 /* 1: PCI state machine ignores parity*/ #define HP100_PCI_RESET 0x80 /* 0->1: Reset PCI block */ /* * Early TX Configuration and Control Register * (Page HW_MAP, EARLYTXCFG, Offset 0x16) */ #define HP100_EN_EARLY_TX 0x8000 /* 1=Enable Early TX */ #define HP100_EN_ADAPTIVE 0x4000 /* 1=Enable adaptive mode */ #define HP100_EN_TX_UR_IRQ 0x2000 /* reserved, must be 0 */ #define HP100_EN_LOW_TX 0x1000 /* reserved, must be 0 */ #define HP100_ET_CNT_MASK 0x0fff /* bits 11..0: ET counters */ /* * Early RX Configuration and Control Register * (Page HW_MAP, EARLYRXCFG, Offset 0x18) */ #define HP100_EN_EARLY_RX 0x80 /* 1=Enable Early RX */ #define HP100_EN_LOW_RX 0x40 /* reserved, must be 0 */ #define HP100_RX_TRIP_MASK 0x1f /* bits 4..0: threshold at which the * early rx circuit will start the * dma of received packet into system * memory for BM */ /* * Serial Devices Control Register * (Page EEPROM_CTRL, EEPROM_CTRL, Offset 0x08) */ #define HP100_EEPROM_LOAD 0x0001 /* 0->1 loads EEPROM into registers. */ /* When it goes back to 0, load is */ /* complete. This should take ~600us.*/ /* * 10MB LAN Control and Configuration Register I * (Page MAC_CTRL, 10_LAN_CFG_1, Offset 0x08) */ #define HP100_MAC10_SEL 0xc0 /* Get bits to indicate MAC */ #define HP100_AUI_SEL 0x20 /* Status of AUI selection */ #define HP100_LOW_TH 0x10 /* 0:No, 1:Yes allow better cabling */ #define HP100_LINK_BEAT_DIS 0x08 /* 0:Enable, 1:Disable link beat */ #define HP100_LINK_BEAT_ST 0x04 /* 0:No, 1:Yes link beat being Rx */ #define HP100_R_ROL_ST 0x02 /* 0:No, 1:Yes Rx twisted pair has */ /* been reversed */ #define HP100_AUI_ST 0x01 /* 0:No, 1:Yes use AUI on TP card */ /* * 10 MB LAN Control and Configuration Register II * (Page MAC_CTRL, 10_LAN_CFG_2, Offset 0x09) */ #define HP100_SQU_ST 0x01 /* 0:No, 1:Yes collision signal sent */ /* after Tx.Only used for AUI. */ #define HP100_FULLDUP 0x02 /* 1: LXT901 XCVR fullduplx enabled */ #define HP100_DOT3_MAC 0x04 /* 1: DOT 3 Mac sel. unless Autosel */ /* * MAC Selection, use with MAC10_SEL bits */ #define HP100_AUTO_SEL_10 0x0 /* Auto select */ #define HP100_XCVR_LXT901_10 0x1 /* LXT901 10BaseT transceiver */ #define HP100_XCVR_7213 0x2 /* 7213 transceiver */ #define HP100_XCVR_82503 0x3 /* 82503 transceiver */ /* * 100MB LAN Training Register * (Page MAC_CTRL, VG_LAN_CFG_2, Offset 0x0b) (old, pre 802.12) */ #define HP100_FRAME_FORMAT 0x08 /* 0:802.3, 1:802.5 frames */ #define HP100_BRIDGE 0x04 /* 0:No, 1:Yes tell hub i am a bridge */ #define HP100_PROM_MODE 0x02 /* 0:No, 1:Yes tell hub card is */ /* promiscuous */ #define HP100_REPEATER 0x01 /* 0:No, 1:Yes tell hub MAC wants to */ /* be a cascaded repeater */ /* * 100MB LAN Control and Configuration Register * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a) */ #define HP100_VG_SEL 0x80 /* 0:No, 1:Yes use 100 Mbit MAC */ #define HP100_LINK_UP_ST 0x40 /* 0:No, 1:Yes endnode logged in */ #define HP100_LINK_CABLE_ST 0x20 /* 0:No, 1:Yes cable can hear tones */ /* from hub */ #define HP100_LOAD_ADDR 0x10 /* 0->1 card addr will be sent */ /* 100ms later the link status */ /* bits are valid */ #define HP100_LINK_CMD 0x08 /* 0->1 link will attempt to log in. */ /* 100ms later the link status */ /* bits are valid */ #define HP100_TRN_DONE 0x04 /* NEW ETR-Chips only: Will be reset */ /* after LinkUp Cmd is given and set */ /* when training has completed. */ #define HP100_LINK_GOOD_ST 0x02 /* 0:No, 1:Yes cable passed training */ #define HP100_VG_RESET 0x01 /* 0:Yes, 1:No reset the 100VG MAC */ /* * MAC Configuration Register I * (Page MAC_CTRL, MAC_CFG_1, Offset 0x0c) */ #define HP100_RX_IDLE 0x80 /* 0:Yes, 1:No currently receiving pkts */ #define HP100_TX_IDLE 0x40 /* 0:Yes, 1:No currently Txing pkts */ #define HP100_RX_EN 0x20 /* 1: allow receiving of pkts */ #define HP100_TX_EN 0x10 /* 1: allow transmitting of pkts */ #define HP100_ACC_ERRORED 0x08 /* 0:No, 1:Yes allow Rx of errored pkts */ #define HP100_ACC_MC 0x04 /* 0:No, 1:Yes allow Rx of multicast pkts */ #define HP100_ACC_BC 0x02 /* 0:No, 1:Yes allow Rx of broadcast pkts */ #define HP100_ACC_PHY 0x01 /* 0:No, 1:Yes allow Rx of ALL phys. pkts */ #define HP100_MAC1MODEMASK 0xf0 /* Hide ACC bits */ #define HP100_MAC1MODE1 0x00 /* Receive nothing, must also disable RX */ #define HP100_MAC1MODE2 0x00 #define HP100_MAC1MODE3 HP100_MAC1MODE2 | HP100_ACC_BC #define HP100_MAC1MODE4 HP100_MAC1MODE3 | HP100_ACC_MC #define HP100_MAC1MODE5 HP100_MAC1MODE4 /* set mc hash to all ones also */ #define HP100_MAC1MODE6 HP100_MAC1MODE5 | HP100_ACC_PHY /* Promiscuous */ /* Note MODE6 will receive all GOOD packets on the LAN. This really needs a mode 7 defined to be LAN Analyzer mode, which will receive errored and runt packets, and keep the CRC bytes. */ #define HP100_MAC1MODE7 HP100_MAC1MODE6 | HP100_ACC_ERRORED /* * MAC Configuration Register II * (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d) */ #define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */ #define HP100_TX_SAME 0x40 /* 0:No, 1:Yes Tx same packet continuous */ #define HP100_LBK_XCVR 0x20 /* 0:No, 1:Yes loopback through MAC & */ /* transceiver */ #define HP100_LBK_MAC 0x10 /* 0:No, 1:Yes loopback through MAC */ #define HP100_CRC_I 0x08 /* 0:No, 1:Yes inhibit CRC on Tx packets */ #define HP100_ACCNA 0x04 /* 1: For 802.5: Accept only token ring * group addr that maches NA mask */ #define HP100_KEEP_CRC 0x02 /* 0:No, 1:Yes keep CRC on Rx packets. */ /* The length will reflect this. */ #define HP100_ACCFA 0x01 /* 1: For 802.5: Accept only functional * addrs that match FA mask (page1) */ #define HP100_MAC2MODEMASK 0x02 #define HP100_MAC2MODE1 0x00 #define HP100_MAC2MODE2 0x00 #define HP100_MAC2MODE3 0x00 #define HP100_MAC2MODE4 0x00 #define HP100_MAC2MODE5 0x00 #define HP100_MAC2MODE6 0x00 #define HP100_MAC2MODE7 KEEP_CRC /* * MAC Configuration Register III * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e) */ #define HP100_PACKET_PACE 0x03 /* Packet Pacing: * 00: No packet pacing * 01: 8 to 16 uS delay * 10: 16 to 32 uS delay * 11: 32 to 64 uS delay */ #define HP100_LRF_EN 0x04 /* 1: External LAN Rcv Filter and * TCP/IP Checksumming enabled. */ #define HP100_AUTO_MODE 0x10 /* 1: AutoSelect between 10/100 */ /* * MAC Configuration Register IV * (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f) */ #define HP100_MAC_SEL_ST 0x01 /* (R): Status of external VGSEL * Signal, 1=100VG, 0=10Mbit sel. */ #define HP100_LINK_FAIL_ST 0x02 /* (R): Status of Link Fail portion * of the Misc. Interrupt */ /* * 100 MB LAN Training Request/Allowed Registers * (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only) */ #define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be * a cascaded repeater * 0: ... wants to be a DTE */ #define HP100_MACRQ_PROMSC 0x0006 /* 2 bits: Promiscious mode * 00: Rcv only unicast packets * specifically addr to this * endnode * 10: Rcv all pckts fwded by * the local repeater */ #define HP100_MACRQ_FRAMEFMT_EITHER 0x0018 /* 11: either format allowed */ #define HP100_MACRQ_FRAMEFMT_802_3 0x0000 /* 00: 802.3 is requested */ #define HP100_MACRQ_FRAMEFMT_802_5 0x0010 /* 10: 802.5 format is requested */ #define HP100_CARD_MACVER 0xe000 /* R: 3 bit Cards 100VG MAC version */ #define HP100_MALLOW_REPEATER 0x0001 /* If reset, requested access as an * end node is allowed */ #define HP100_MALLOW_PROMSC 0x0004 /* 2 bits: Promiscious mode * 00: Rcv only unicast packets * specifically addr to this * endnode * 10: Rcv all pckts fwded by * the local repeater */ #define HP100_MALLOW_FRAMEFMT 0x00e0 /* 2 bits: Frame Format * 00: 802.3 format will be used * 10: 802.5 format will be used */ #define HP100_MALLOW_ACCDENIED 0x0400 /* N bit */ #define HP100_MALLOW_CONFIGURE 0x0f00 /* C bit */ #define HP100_MALLOW_DUPADDR 0x1000 /* D bit */ #define HP100_HUB_MACVER 0xe000 /* R: 3 bit 802.12 MAC/RMAC training */ /* protocol of repeater */ /* ****************************************************************************** */ /* * Set/Reset bits */ #define HP100_SET_HB 0x0100 /* 0:Set fields to 0 whose mask is 1 */ #define HP100_SET_LB 0x0001 /* HB sets upper byte, LB sets lower byte */ #define HP100_RESET_HB 0x0000 /* For readability when resetting bits */ #define HP100_RESET_LB 0x0000 /* For readability when resetting bits */ /* * Misc. Constants */ #define HP100_LAN_100 100 /* lan_type value for VG */ #define HP100_LAN_10 10 /* lan_type value for 10BaseT */ #define HP100_LAN_ERR (-1) /* lan_type value for link down */ #define TRUE 1 #define FALSE 0 /* * Bus Master Data Structures ---------------------------------------------- */ #define MAX_RX_PDL 30 /* Card limit = 31 */ #define MAX_RX_FRAG 2 /* Don't need more... */ #define MAX_TX_PDL 29 #define MAX_TX_FRAG 2 /* Limit = 31 */ /* Define total PDL area size in bytes (should be 4096) */ /* This is the size of kernel (dma) memory that will be allocated. */ #define MAX_RINGSIZE ((MAX_RX_FRAG*8+4+4)*MAX_RX_PDL+(MAX_TX_FRAG*8+4+4)*MAX_TX_PDL)+16 /* Ethernet Packet Sizes */ #define MIN_ETHER_SIZE 60 #define MAX_ETHER_SIZE 1514 /* Needed for preallocation of */ /* skb buffer when busmastering */ /* Tx or Rx Ring Entry */ typedef struct hp100_ring { u_int *pdl; /* Address of PDLs PDH, dword before * this address is used for rx hdr */ u_int pdl_paddr; /* Physical address of PDL */ struct sk_buff *skb; struct hp100_ring *next; } hp100_ring_t; /* Mask for Header Descriptor */ #define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length */ /* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED bit in the MAC Configuration Register 1 is set. */ #define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */ #define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */ #define HP100_SKEW_ERR 0x2000 /* 0:No, 1:Yes skew out of range */ #define HP100_BAD_SYMBOL_ERR 0x1000 /* 0:No, 1:Yes invalid symbol received */ #define HP100_RCV_IPM_ERR 0x0800 /* 0:No, 1:Yes pkt had an invalid packet */ /* marker */ #define HP100_SYMBOL_BAL_ERR 0x0400 /* 0:No, 1:Yes symbol balance error */ #define HP100_VG_ALN_ERR 0x0200 /* 0:No, 1:Yes non-octet received */ #define HP100_TRUNC_ERR 0x0100 /* 0:No, 1:Yes the packet was truncated */ #define HP100_RUNT_ERR 0x0040 /* 0:No, 1:Yes pkt length < Min Pkt */ /* Length Reg. */ #define HP100_ALN_ERR 0x0010 /* 0:No, 1:Yes align error. */ #define HP100_CRC_ERR 0x0008 /* 0:No, 1:Yes CRC occurred. */ /* The last three bits indicate the type of destination address */ #define HP100_MULTI_ADDR_HASH 0x0006 /* 110: Addr multicast, matched hash */ #define HP100_BROADCAST_ADDR 0x0003 /* x11: Addr broadcast */ #define HP100_MULTI_ADDR_NO_HASH 0x0002 /* 010: Addr multicast, didn't match hash */ #define HP100_PHYS_ADDR_MATCH 0x0001 /* x01: Addr was physical and mine */ #define HP100_PHYS_ADDR_NO_MATCH 0x0000 /* x00: Addr was physical but not mine */ /* * macros */ #define hp100_inb( reg ) \ inb( ioaddr + HP100_REG_##reg ) #define hp100_inw( reg ) \ inw( ioaddr + HP100_REG_##reg ) #define hp100_inl( reg ) \ inl( ioaddr + HP100_REG_##reg ) #define hp100_outb( data, reg ) \ outb( data, ioaddr + HP100_REG_##reg ) #define hp100_outw( data, reg ) \ outw( data, ioaddr + HP100_REG_##reg ) #define hp100_outl( data, reg ) \ outl( data, ioaddr + HP100_REG_##reg ) #define hp100_orb( data, reg ) \ outb( inb( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg ) #define hp100_orw( data, reg ) \ outw( inw( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg ) #define hp100_andb( data, reg ) \ outb( inb( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg ) #define hp100_andw( data, reg ) \ outw( inw( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg ) #define hp100_page( page ) \ outw( HP100_PAGE_##page, ioaddr + HP100_REG_PAGING ) #define hp100_ints_off() \ outw( HP100_INT_EN | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW ) #define hp100_ints_on() \ outw( HP100_INT_EN | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW ) #define hp100_mem_map_enable() \ outw( HP100_MMAP_DIS | HP100_RESET_HB, ioaddr + HP100_REG_OPTION_LSW ) #define hp100_mem_map_disable() \ outw( HP100_MMAP_DIS | HP100_SET_HB, ioaddr + HP100_REG_OPTION_LSW ) /* * Local variables: * c-indent-level: 2 * tab-width: 8 * End: */