URL
https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k
[/] [or1k/] [trunk/] [uclinux/] [uClinux-2.0.x/] [drivers/] [net/] [wavelan.h] - Rev 1775
Go to most recent revision | Compare with Previous | Blame | View Log
/* * Wavelan ISA driver * * Jean II - HPLB '96 * * Reorganisation and extension of the driver. * Original copyrigth follow. See wavelan.p.h for details. * * This file contain the declarations of the Wavelan hardware. Note that * the Wavelan ISA include a i82586 controler (see definitions in * file i82586.h). * * The main difference between the ISA hardware and the pcmcia one is * the Ethernet Controler (i82586 instead of i82593). * The i82586 allow multiple transmit buffers. The PSA need to be accessed * through the host interface. */ #ifndef _WAVELAN_H #define _WAVELAN_H /* The detection of the wavelan card is made by reading the MAC * address from the card and checking it. If you have a non AT&T * product (OEM, like DEC RoamAbout, or Digital Ocean, Epson, ...), * you might need to modify this part to accomodate your hardware... */ const char MAC_ADDRESSES[][3] = { { 0x08, 0x00, 0x0E }, /* AT&T Wavelan (standard) & DEC RoamAbout */ { 0x08, 0x00, 0x6A }, /* AT&T Wavelan (alternate) */ { 0x00, 0x00, 0xE1 }, /* Hitachi Wavelan */ { 0x00, 0x60, 0x1D } /* Lucent Wavelan (another one) */ /* Add your card here and send me the patch ! */ }; #define WAVELAN_ADDR_SIZE 6 /* Size of a MAC address */ #define WAVELAN_MTU 1500 /* Maximum size of WaveLAN packet */ #define MAXDATAZ (WAVELAN_ADDR_SIZE + WAVELAN_ADDR_SIZE + 2 + WAVELAN_MTU) /*************************** PC INTERFACE ****************************/ /* * Host Adaptor structure. * (base is board port address). */ typedef union hacs_u hacs_u; union hacs_u { unsigned short hu_command; /* Command register */ #define HACR_RESET 0x0001 /* Reset board */ #define HACR_CA 0x0002 /* Set Channel Attention for 82586 */ #define HACR_16BITS 0x0004 /* 16 bits operation (0 => 8bits) */ #define HACR_OUT0 0x0008 /* General purpose output pin 0 */ /* not used - must be 1 */ #define HACR_OUT1 0x0010 /* General purpose output pin 1 */ /* not used - must be 1 */ #define HACR_82586_INT_ENABLE 0x0020 /* Enable 82586 interrupts */ #define HACR_MMC_INT_ENABLE 0x0040 /* Enable MMC interrupts */ #define HACR_INTR_CLR_ENABLE 0x0080 /* Enable interrupt status read/clear */ unsigned short hu_status; /* Status Register */ #define HASR_82586_INTR 0x0001 /* Interrupt request from 82586 */ #define HASR_MMC_INTR 0x0002 /* Interrupt request from MMC */ #define HASR_MMC_BUSY 0x0004 /* MMC busy indication */ #define HASR_PSA_BUSY 0x0008 /* LAN parameter storage area busy */ }; typedef struct ha_t ha_t; struct ha_t { hacs_u ha_cs; /* Command and status registers */ #define ha_command ha_cs.hu_command #define ha_status ha_cs.hu_status unsigned short ha_mmcr; /* Modem Management Ctrl Register */ unsigned short ha_pior0; /* Program I/O Address Register Port 0 */ unsigned short ha_piop0; /* Program I/O Port 0 */ unsigned short ha_pior1; /* Program I/O Address Register Port 1 */ unsigned short ha_piop1; /* Program I/O Port 1 */ unsigned short ha_pior2; /* Program I/O Address Register Port 2 */ unsigned short ha_piop2; /* Program I/O Port 2 */ }; #define HA_SIZE 16 #define hoff(p,f) (unsigned short)((void *)(&((ha_t *)((void *)0 + (p)))->f) - (void *)0) #define HACR(p) hoff(p, ha_command) #define HASR(p) hoff(p, ha_status) #define MMCR(p) hoff(p, ha_mmcr) #define PIOR0(p) hoff(p, ha_pior0) #define PIOP0(p) hoff(p, ha_piop0) #define PIOR1(p) hoff(p, ha_pior1) #define PIOP1(p) hoff(p, ha_piop1) #define PIOR2(p) hoff(p, ha_pior2) #define PIOP2(p) hoff(p, ha_piop2) /* * Program I/O Mode Register values. */ #define STATIC_PIO 0 /* Mode 1: static mode */ /* RAM access ??? */ #define AUTOINCR_PIO 1 /* Mode 2: auto increment mode */ /* RAM access ??? */ #define AUTODECR_PIO 2 /* Mode 3: auto decrement mode */ /* RAM access ??? */ #define PARAM_ACCESS_PIO 3 /* Mode 4: LAN parameter access mode */ /* Parameter access. */ #define PIO_MASK 3 /* register mask */ #define PIOM(cmd,piono) ((u_short)cmd << 10 << (piono * 2)) #define HACR_DEFAULT (HACR_OUT0 | HACR_OUT1 | HACR_16BITS | PIOM(STATIC_PIO, 0) | PIOM(AUTOINCR_PIO, 1) | PIOM(PARAM_ACCESS_PIO, 2)) #define HACR_INTRON (HACR_82586_INT_ENABLE | HACR_MMC_INT_ENABLE | HACR_INTR_CLR_ENABLE) /************************** MEMORY LAYOUT **************************/ /* * Onboard 64k RAM layout. * (Offsets from 0x0000.) */ #define OFFSET_RU 0x0000 /* 75 % memory */ #define OFFSET_CU 0xC000 /* 25 % memory */ #define OFFSET_SCB (OFFSET_ISCP - sizeof(scb_t)) #define OFFSET_ISCP (OFFSET_SCP - sizeof(iscp_t)) #define OFFSET_SCP I82586_SCP_ADDR #define RXBLOCKZ (sizeof(fd_t) + sizeof(rbd_t) + MAXDATAZ) #define TXBLOCKZ (sizeof(ac_tx_t) + sizeof(ac_nop_t) + sizeof(tbd_t) + MAXDATAZ) #define NRXBLOCKS ((OFFSET_CU - OFFSET_RU) / RXBLOCKZ) #define NTXBLOCKS ((OFFSET_SCB - OFFSET_CU) / TXBLOCKZ) /********************** PARAMETER STORAGE AREA **********************/ /* * Parameter Storage Area (PSA). */ typedef struct psa_t psa_t; struct psa_t { unsigned char psa_io_base_addr_1; /* [0x00] Base address 1 ??? */ unsigned char psa_io_base_addr_2; /* [0x01] Base address 2 */ unsigned char psa_io_base_addr_3; /* [0x02] Base address 3 */ unsigned char psa_io_base_addr_4; /* [0x03] Base address 4 */ unsigned char psa_rem_boot_addr_1; /* [0x04] Remote Boot Address 1 */ unsigned char psa_rem_boot_addr_2; /* [0x05] Remote Boot Address 2 */ unsigned char psa_rem_boot_addr_3; /* [0x06] Remote Boot Address 3 */ unsigned char psa_holi_params; /* [0x07] HOst Lan Interface (HOLI) Parameters */ unsigned char psa_int_req_no; /* [0x08] Interrupt Request Line */ unsigned char psa_unused0[7]; /* [0x09-0x0F] unused */ unsigned char psa_univ_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x10-0x15] Universal (factory) MAC Address */ unsigned char psa_local_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x16-1B] Local MAC Address */ unsigned char psa_univ_local_sel; /* [0x1C] Universal Local Selection */ #define PSA_UNIVERSAL 0 /* Universal (factory) */ #define PSA_LOCAL 1 /* Local */ unsigned char psa_comp_number; /* [0x1D] Compatability Number: */ #define PSA_COMP_PC_AT_915 0 /* PC-AT 915 MHz */ #define PSA_COMP_PC_MC_915 1 /* PC-MC 915 MHz */ #define PSA_COMP_PC_AT_2400 2 /* PC-AT 2.4 GHz */ #define PSA_COMP_PC_MC_2400 3 /* PC-MC 2.4 GHz */ #define PSA_COMP_PCMCIA_915 4 /* PCMCIA 915 MHz or 2.0 */ unsigned char psa_thr_pre_set; /* [0x1E] Modem Threshold Preset */ unsigned char psa_feature_select; /* [0x1F] Call code required (1=on) */ #define PSA_FEATURE_CALL_CODE 0x01 /* Call code required (Japan) */ unsigned char psa_subband; /* [0x20] Subband */ #define PSA_SUBBAND_915 0 /* 915 MHz or 2.0 */ #define PSA_SUBBAND_2425 1 /* 2425 MHz */ #define PSA_SUBBAND_2460 2 /* 2460 MHz */ #define PSA_SUBBAND_2484 3 /* 2484 MHz */ #define PSA_SUBBAND_2430_5 4 /* 2430.5 MHz */ unsigned char psa_quality_thr; /* [0x21] Modem Quality Threshold */ unsigned char psa_mod_delay; /* [0x22] Modem Delay ??? (reserved) */ unsigned char psa_nwid[2]; /* [0x23-0x24] Network ID */ unsigned char psa_nwid_select; /* [0x25] Network ID Select On Off */ unsigned char psa_encryption_select; /* [0x26] Encryption On Off */ unsigned char psa_encryption_key[8]; /* [0x27-0x2E] Encryption Key */ unsigned char psa_databus_width; /* [0x2F] AT bus width select 8/16 */ unsigned char psa_call_code[8]; /* [0x30-0x37] (Japan) Call Code */ unsigned char psa_nwid_prefix[2]; /* [0x38-0x39] Roaming domain */ unsigned char psa_reserved[2]; /* [0x3A-0x3B] Reserved - fixed 00 */ unsigned char psa_conf_status; /* [0x3C] Conf Status, bit 0=1:config*/ unsigned char psa_crc[2]; /* [0x3D] CRC-16 over PSA */ unsigned char psa_crc_status; /* [0x3F] CRC Valid Flag */ }; #define PSA_SIZE 64 /* Calculate offset of a field in the above structure * Warning : only even addresses are used */ #define psaoff(p,f) ((unsigned short) ((void *)(&((psa_t *) ((void *) NULL + (p)))->f) - (void *) NULL)) /******************** MODEM MANAGEMENT INTERFACE ********************/ /* * Modem Management Controller (MMC) write structure. */ typedef struct mmw_t mmw_t; struct mmw_t { unsigned char mmw_encr_key[8]; /* encryption key */ unsigned char mmw_encr_enable; /* enable/disable encryption */ #define MMW_ENCR_ENABLE_MODE 0x02 /* Mode of security option */ #define MMW_ENCR_ENABLE_EN 0x01 /* Enable security option */ unsigned char mmw_unused0[1]; /* unused */ unsigned char mmw_des_io_invert; /* Encryption option */ #define MMW_DES_IO_INVERT_RES 0x0F /* Reserved */ #define MMW_DES_IO_INVERT_CTRL 0xF0 /* Control ??? (set to 0) */ unsigned char mmw_unused1[5]; /* unused */ unsigned char mmw_loopt_sel; /* looptest selection */ #define MMW_LOOPT_SEL_DIS_NWID 0x40 /* disable NWID filtering */ #define MMW_LOOPT_SEL_INT 0x20 /* activate Attention Request */ #define MMW_LOOPT_SEL_LS 0x10 /* looptest w/o collision avoidance */ #define MMW_LOOPT_SEL_LT3A 0x08 /* looptest 3a */ #define MMW_LOOPT_SEL_LT3B 0x04 /* looptest 3b */ #define MMW_LOOPT_SEL_LT3C 0x02 /* looptest 3c */ #define MMW_LOOPT_SEL_LT3D 0x01 /* looptest 3d */ unsigned char mmw_jabber_enable; /* jabber timer enable */ /* Abort transmissions > 200 ms */ unsigned char mmw_freeze; /* freeze / unfreeeze signal level */ /* 0 : signal level & qual updated for every new message, 1 : frozen */ unsigned char mmw_anten_sel; /* antenna selection */ #define MMW_ANTEN_SEL_SEL 0x01 /* direct antenna selection */ #define MMW_ANTEN_SEL_ALG_EN 0x02 /* antenna selection algo. enable */ unsigned char mmw_ifs; /* inter frame spacing */ /* min time between transmission in bit periods (.5 us) - bit 0 ignored */ unsigned char mmw_mod_delay; /* modem delay (synchro) */ unsigned char mmw_jam_time; /* jamming time (after collision) */ unsigned char mmw_unused2[1]; /* unused */ unsigned char mmw_thr_pre_set; /* level threshold preset */ /* Discard all packet with signal < this value (4) */ unsigned char mmw_decay_prm; /* decay parameters */ unsigned char mmw_decay_updat_prm; /* decay update parameterz */ unsigned char mmw_quality_thr; /* quality (z-quotient) threshold */ /* Discard all packet with quality < this value (3) */ unsigned char mmw_netw_id_l; /* NWID low order byte */ unsigned char mmw_netw_id_h; /* NWID high order byte */ /* Network ID or Domain : create virtual net on the air */ /* 2.0 Hardware extension - frequency selection support */ unsigned char mmw_mode_select; /* for analog tests (set to 0) */ unsigned char mmw_unused3[1]; /* unused */ unsigned char mmw_fee_ctrl; /* frequency eeprom control */ #define MMW_FEE_CTRL_PRE 0x10 /* Enable protected instructions */ #define MMW_FEE_CTRL_DWLD 0x08 /* Download eeprom to mmc */ #define MMW_FEE_CTRL_CMD 0x07 /* EEprom commands : */ #define MMW_FEE_CTRL_READ 0x06 /* Read */ #define MMW_FEE_CTRL_WREN 0x04 /* Write enable */ #define MMW_FEE_CTRL_WRITE 0x05 /* Write data to address */ #define MMW_FEE_CTRL_WRALL 0x04 /* Write data to all addresses */ #define MMW_FEE_CTRL_WDS 0x04 /* Write disable */ #define MMW_FEE_CTRL_PRREAD 0x16 /* Read addr from protect register */ #define MMW_FEE_CTRL_PREN 0x14 /* Protect register enable */ #define MMW_FEE_CTRL_PRCLEAR 0x17 /* Unprotect all registers */ #define MMW_FEE_CTRL_PRWRITE 0x15 /* Write addr in protect register */ #define MMW_FEE_CTRL_PRDS 0x14 /* Protect register disable */ /* Never issue this command (PRDS) : it's irreversible !!! */ unsigned char mmw_fee_addr; /* EEprom address */ #define MMW_FEE_ADDR_CHANNEL 0xF0 /* Select the channel */ #define MMW_FEE_ADDR_OFFSET 0x0F /* Offset in channel data */ #define MMW_FEE_ADDR_EN 0xC0 /* FEE_CTRL enable operations */ #define MMW_FEE_ADDR_DS 0x00 /* FEE_CTRL disable operations */ #define MMW_FEE_ADDR_ALL 0x40 /* FEE_CTRL all operations */ #define MMW_FEE_ADDR_CLEAR 0xFF /* FEE_CTRL clear operations */ unsigned char mmw_fee_data_l; /* Write data to EEprom */ unsigned char mmw_fee_data_h; /* high octet */ unsigned char mmw_ext_ant; /* Setting for external antenna */ #define MMW_EXT_ANT_EXTANT 0x01 /* Select external antenna */ #define MMW_EXT_ANT_POL 0x02 /* Polarity of the antenna */ #define MMW_EXT_ANT_INTERNAL 0x00 /* Internal antenna */ #define MMW_EXT_ANT_EXTERNAL 0x03 /* External antenna */ #define MMW_EXT_ANT_IQ_TEST 0x1C /* IQ test pattern (set to 0) */ }; #define MMW_SIZE 37 #define mmwoff(p,f) (unsigned short)((void *)(&((mmw_t *)((void *)0 + (p)))->f) - (void *)0) /* * Modem Management Controller (MMC) read structure. */ typedef struct mmr_t mmr_t; struct mmr_t { unsigned char mmr_unused0[8]; /* unused */ unsigned char mmr_des_status; /* encryption status */ unsigned char mmr_des_avail; /* encryption available (0x55 read) */ #define MMR_DES_AVAIL_DES 0x55 /* DES available */ #define MMR_DES_AVAIL_AES 0x33 /* AES (AT&T) available */ unsigned char mmr_des_io_invert; /* des I/O invert register */ unsigned char mmr_unused1[5]; /* unused */ unsigned char mmr_dce_status; /* DCE status */ #define MMR_DCE_STATUS_RX_BUSY 0x01 /* receiver busy */ #define MMR_DCE_STATUS_LOOPT_IND 0x02 /* loop test indicated */ #define MMR_DCE_STATUS_TX_BUSY 0x04 /* transmitter on */ #define MMR_DCE_STATUS_JBR_EXPIRED 0x08 /* jabber timer expired */ #define MMR_DCE_STATUS 0x0F /* mask to get the bits */ unsigned char mmr_dsp_id; /* DSP id (AA = Daedalus rev A) */ unsigned char mmr_unused2[2]; /* unused */ unsigned char mmr_correct_nwid_l; /* # of correct NWID's rxd (low) */ unsigned char mmr_correct_nwid_h; /* # of correct NWID's rxd (high) */ /* Warning : Read high order octet first !!! */ unsigned char mmr_wrong_nwid_l; /* # of wrong NWID's rxd (low) */ unsigned char mmr_wrong_nwid_h; /* # of wrong NWID's rxd (high) */ unsigned char mmr_thr_pre_set; /* level threshold preset */ #define MMR_THR_PRE_SET 0x3F /* level threshold preset */ #define MMR_THR_PRE_SET_CUR 0x80 /* Current signal above it */ unsigned char mmr_signal_lvl; /* signal level */ #define MMR_SIGNAL_LVL 0x3F /* signal level */ #define MMR_SIGNAL_LVL_VALID 0x80 /* Updated since last read */ unsigned char mmr_silence_lvl; /* silence level (noise) */ #define MMR_SILENCE_LVL 0x3F /* silence level */ #define MMR_SILENCE_LVL_VALID 0x80 /* Updated since last read */ unsigned char mmr_sgnl_qual; /* signal quality */ #define MMR_SGNL_QUAL 0x0F /* signal quality */ #define MMR_SGNL_QUAL_ANT 0x80 /* current antenna used */ unsigned char mmr_netw_id_l; /* NWID low order byte ??? */ unsigned char mmr_unused3[3]; /* unused */ /* 2.0 Hardware extension - frequency selection support */ unsigned char mmr_fee_status; /* Status of frequency eeprom */ #define MMR_FEE_STATUS_ID 0xF0 /* Modem revision id */ #define MMR_FEE_STATUS_DWLD 0x08 /* Download in progress */ #define MMR_FEE_STATUS_BUSY 0x04 /* EEprom busy */ unsigned char mmr_unused4[1]; /* unused */ unsigned char mmr_fee_data_l; /* Read data from eeprom (low) */ unsigned char mmr_fee_data_h; /* Read data from eeprom (high) */ }; #define MMR_SIZE 36 #define mmroff(p,f) (unsigned short)((void *)(&((mmr_t *)((void *)0 + (p)))->f) - (void *)0) /* Make the two above structures one */ typedef union mm_t { struct mmw_t w; /* Write to the mmc */ struct mmr_t r; /* Read from the mmc */ } mm_t; #endif /* _WAVELAN_H */ /* * This software may only be used and distributed * according to the terms of the GNU Public License. * * For more details, see wavelan.c. */
Go to most recent revision | Compare with Previous | Blame | View Log