Subversion Repositories or1k_old

#
# For a description of the syntax of this configuration file,
# see the Configure script.
#
mainmenu_name 'uClinux/OR1K (w/o MMU) Kernel Configuration'

define_bool CONFIG_UCLINUX y

mainmenu_option next_comment
comment 'Code maturity level options'
bool 'Prompt for development and/or incomplete code/drivers' CONFIG_EXPERIMENTAL
endmenu

# mainmenu_option next_comment
# comment 'Loadable module support'
# bool 'Enable loadable module support' CONFIG_MODULES
# if [ "$CONFIG_MODULES" = "y" ]; then
#   bool 'Set version information on all symbols for modules' CONFIG_MODVERSIONS
#   bool 'Kernel daemon support (e.g. autoload of modules)' CONFIG_KERNELD
# fi
# endmenu


mainmenu_option next_comment
comment 'Platform dependant setup'

choice 'CPU' \
        "OR32           CONFIG_OR32" OR32

comment 'Platform'

if [ "$CONFIG_OR32" = "y" ]; then
        bool 'General OR32 board support' CONFIG_GEN
fi

choice 'Kernel executes from' \
        "RAM    CONFIG_RAMKERNEL \
         ROM    CONFIG_ROMKERNEL" RAM

endmenu

mainmenu_option next_comment
comment 'General setup'

bool 'PCI bios support' CONFIG_PCI
if [ "$CONFIG_PCI" = "y" ]; then
        bool '    PCI device list support' CONFIG_PCIDEVLIST
fi

bool 'Networking support' CONFIG_NET
bool 'System V IPC' CONFIG_SYSVIPC
bool 'Reduced memory footprint' CONFIG_REDUCED_MEMORY
tristate 'Kernel support for flat binaries' CONFIG_BINFMT_FLAT
# tristate 'Kernel support for a.out binaries' CONFIG_BINFMT_AOUT
tristate 'Kernel support for ELF binaries' CONFIG_BINFMT_ELF
bool 'Compile kernel as ELF - if your GCC is ELF-GCC' CONFIG_KERNEL_ELF
bool 'Console support' CONFIG_CONSOLE
if [ "$CONFIG_CONSOLE" = "y" ]; then
        bool 'Enable serial echo' CONFIG_SERIAL_ECHO
        bool 'Frame buffer' CONFIG_FRAMEBUFFER
fi

endmenu

#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Floppy, IDE, and other block devices'

tristate 'ROM disk memory block device' CONFIG_BLK_DEV_BLKMEM
# tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
bool 'IDE harddisk support' CONFIG_BLK_DEV_IDE
if [ "$CONFIG_BLK_DEV_IDE" = "y" ]; then
  bool '   Include IDE/ATAPI CDROM support' CONFIG_BLK_DEV_IDECD
  bool '   Include IDE/ATAPI TAPE support' CONFIG_BLK_DEV_IDETAPE
  bool '   Include IDE/ATAPI FLOPPY support (new)' CONFIG_BLK_DEV_IDEFLOPPY
fi

comment 'Additional Block/FLASH Devices'

tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
bool 'Multiple devices driver support' CONFIG_BLK_DEV_MD
if [ "$CONFIG_BLK_DEV_MD" = "y" ]; then
  tristate '   Linear (append) mode' CONFIG_MD_LINEAR
  tristate '   RAID-0 (striping) mode' CONFIG_MD_STRIPED
fi
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" ]; then
  bool '   Release empty RAM disk blocks' CONFIG_RD_RELEASE_BLOCKS
  bool '   Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD
fi
tristate 'FLASH device support' CONFIG_DEV_FLASH
if [ "$CONFIG_DEV_FLASH" = "y" ]; then
  bool '   FLASH Block device' CONFIG_BLK_DEV_FLASH
  bool '   FLASH Character device' CONFIG_CHR_DEV_FLASH
fi
endmenu

if [ "$CONFIG_NET" = "y" ]; then
  source net/Config.in
fi

if [ "$CONFIG_NET" = "y" ]; then

mainmenu_option next_comment
comment 'Network device support'

bool 'Network device support' CONFIG_NETDEVICES
if [ "$CONFIG_NETDEVICES" = "y" ]; then
#
# Network device configuration
#
tristate 'Dummy net driver support' CONFIG_DUMMY
tristate 'SLIP (serial line) support' CONFIG_SLIP
if [ "$CONFIG_SLIP" != "n" ]; then
  bool ' CSLIP compressed headers' CONFIG_SLIP_COMPRESSED
  bool ' Keepalive and linefill' CONFIG_SLIP_SMART
  bool ' Six bit SLIP encapsulation' CONFIG_SLIP_MODE_SLIP6
fi
tristate 'PPP (point-to-point) support' CONFIG_PPP
if [ ! "$CONFIG_PPP" = "n" ]; then
  comment 'CCP compressors for PPP are only built as modules.'
fi
tristate 'EQL (serial line load balancing) support' CONFIG_EQUALIZER
bool 'Open ethernet core' CONFIG_OETH
bool 'SMC91111' CONFIG_SMC91111

fi
endmenu
fi

source fs/Config.in

mainmenu_option next_comment
comment 'Character devices'

bool 'Serial support' CONFIG_SERIAL
# bool 'Support for user serial device modules' CONFIG_USERIAL
bool 'Watchdog Timer Support'   CONFIG_WATCHDOG
# if [ "$CONFIG_WATCHDOG" != "n" ]; then
#   bool '   Disable watchdog shutdown on close' CONFIG_WATCHDOG_NOWAYOUT
#   bool '   Software Watchdog' CONFIG_SOFT_WATCHDOG
# fi
bool 'PS/2 Keyboard' CONFIG_KEYBOARD
endmenu

# mainmenu_option next_comment
# comment 'Sound support'
#
# tristate 'Sound support' CONFIG_SOUND
# endmenu

mainmenu_option next_comment
comment 'Kernel hacking'

# bool 'Debug kmalloc/kfree' CONFIG_DEBUG_MALLOC
bool 'Kernel profiling support' CONFIG_PROFILE
if [ "$CONFIG_PROFILE" = "y" ]; then
  int ' Profile shift count' CONFIG_PROFILE_SHIFT 2
fi
endmenu