Subversion Repositories or1k_old

#ifndef _QIC117_H
#define _QIC117_H
 
/*
 *      Copyright (C) 1993-1995 Bas Laarhoven.
 
 This program is free software; you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation; either version 2, or (at your option)
 any later version.
 
 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 GNU General Public License for more details.
 
 You should have received a copy of the GNU General Public License
 along with this program; see the file COPYING.  If not, write to
 the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
 
 *
 $Source: /home/marcus/revision_ctrl_test/oc_cvs/cvs/or1k/uclinux/uClinux-2.0.x/drivers/char/ftape/qic117.h,v $
 $Author: simons $
 *
 $Revision: 1.1.1.1 $
 $Date: 2001-09-10 07:44:18 $
 $State: Exp $
 *
 *      This file contains QIC-117 spec. related definitions
 *      for the QIC-40/80 floppy-tape driver for Linux.
 *
 *      These data were taken from the Quarter-Inch Cartridge
 *      Drive Standards, Inc. document titled:
 *      `Common Command Set Interface Specification for Flexible
 *       Disk Controller Based Minicartridge Tape Drives'
 *       document QIC-117 Revision C, 3 Dec 92.
 *      For more information, contact:
 *       Quarter-Inch Cartridge Drive Standards, Inc.
 *       311 East Carrillo Street
 *       Santa Barbara, California 93101
 *       Telephone (805) 963-3853
 *       Fax       (805) 962-1541
 *
 *      Current QIC standard revisions (of interest) are:
 *       QIC-80-MC,   Rev. M, 15 Jun 95.
 *       QIC-117,     Rev. I, 15 Mar 95.
 *       QIC-122,     Rev. B,  6 Mar 91.
 *       QIC-130,     Rev. C,  2 Sep 92.
 *       QIC-3010-MC, Rev. F, 14 Jun 95.
 *       QIC-3020-MC, Rev. G, 31 Aug 95.
 *       QIC-CRF3,    Rev. B, 15 Jun 95.
 *
 */
 
/*
 *      QIC-117 common command set rev. I.
 *      These commands are sent to the tape unit
 *      as number of pulses over the step line.
 */
 
#define QIC_RESET			1
#define QIC_REPORT_NEXT_BIT		2
#define QIC_PAUSE			3
#define QIC_MICRO_STEP_PAUSE		4
#define QIC_ALTERNATE_TIMEOUT		5
#define QIC_REPORT_DRIVE_STATUS		6
#define QIC_REPORT_ERROR_CODE		7
#define QIC_REPORT_DRIVE_CONFIGURATION	8
#define QIC_REPORT_ROM_VERSION		9
#define QIC_LOGICAL_FORWARD		10
#define QIC_PHYSICAL_REVERSE		11
#define QIC_PHYSICAL_FORWARD		12
#define QIC_SEEK_HEAD_TO_TRACK		13
#define QIC_SEEK_LOAD_POINT		14
#define QIC_ENTER_FORMAT_MODE		15
#define QIC_WRITE_REFERENCE_BURST	16
#define QIC_ENTER_VERIFY_MODE		17
#define QIC_STOP_TAPE			18
/* commands 19-20: reserved */
#define QIC_MICRO_STEP_HEAD_UP		21
#define QIC_MICRO_STEP_HEAD_DOWN	22
#define QIC_SOFT_SELECT			23
#define QIC_SOFT_DESELECT		24
#define QIC_SKIP_REVERSE		25
#define QIC_SKIP_FORWARD		26
#define QIC_SELECT_RATE			27
/* command 27, in ccs2: Select Rate or Format */
#define QIC_ENTER_DIAGNOSTIC_1		28
#define QIC_ENTER_DIAGNOSTIC_2		29
#define QIC_ENTER_PRIMARY_MODE		30
/* command 31: vendor unique */
#define QIC_REPORT_VENDOR_ID		32
#define QIC_REPORT_TAPE_STATUS		33
#define QIC_SKIP_EXTENDED_REVERSE	34
#define QIC_SKIP_EXTENDED_FORWARD	35
#define QIC_CALIBRATE_TAPE_LENGTH	36
#define QIC_REPORT_FORMAT_SEGMENTS	37
#define QIC_SET_FORMAT_SEGMENTS		38
/* commands 39-45: reserved */
#define QIC_PHANTOM_SELECT		46
#define QIC_PHANTOM_DESELECT		47
 
typedef enum {
	discretional = 0, required, ccs1, ccs2
} qic_compatibility;
 
typedef enum {
	unused, mode, motion, report
} command_types;
 
struct qic117_command_table {
	char *name;
	byte mask;
	byte state;
	byte cmd_type;
	byte non_intr;
	byte level;
};
 
#define QIC117_COMMANDS {\
/* command                           mask  state cmd_type           */\
/* |    name                         |     |     |       non_intr   */\
/* |    |                            |     |     |       |  level   */\
/* 0*/ {NULL,                        0x00, 0x00, mode,   0, discretional},\
/* 1*/ {"soft reset",                0x00, 0x00, motion, 1, required},\
/* 2*/ {"report next bit",           0x00, 0x00, report, 0, required},\
/* 3*/ {"pause",                     0x36, 0x24, motion, 1, required},\
/* 4*/ {"micro step pause",          0x36, 0x24, motion, 1, required},\
/* 5*/ {"alternate command timeout", 0x00, 0x00, mode,   0, required},\
/* 6*/ {"report drive status",       0x00, 0x00, report, 0, required},\
/* 7*/ {"report error code",         0x01, 0x01, report, 0, required},\
/* 8*/ {"report drive configuration",0x00, 0x00, report, 0, required},\
/* 9*/ {"report rom version",        0x00, 0x00, report, 0, required},\
/*10*/ {"logical forward",           0x37, 0x25, motion, 0, required},\
/*11*/ {"physical reverse",          0x17, 0x05, motion, 0, required},\
/*12*/ {"physical forward",          0x17, 0x05, motion, 0, required},\
/*13*/ {"seek head to track",        0x37, 0x25, motion, 0, required},\
/*14*/ {"seek load point",           0x17, 0x05, motion, 1, required},\
/*15*/ {"enter format mode",         0x1f, 0x05, mode,   0, required},\
/*16*/ {"write reference burst",     0x1f, 0x05, motion, 1, required},\
/*17*/ {"enter verify mode",         0x37, 0x25, mode,   0, required},\
/*18*/ {"stop tape",                 0x00, 0x00, motion, 1, required},\
/*19*/ {"reserved (19)",             0x00, 0x00, unused, 0, discretional},\
/*20*/ {"reserved (20)",             0x00, 0x00, unused, 0, discretional},\
/*21*/ {"micro step head up",        0x02, 0x00, motion, 0, required},\
/*22*/ {"micro step head down",      0x02, 0x00, motion, 0, required},\
/*23*/ {"soft select",               0x00, 0x00, mode,   0, discretional},\
/*24*/ {"soft deselect",             0x00, 0x00, mode,   0, discretional},\
/*25*/ {"skip segments reverse",     0x36, 0x24, motion, 1, required},\
/*26*/ {"skip segments forward",     0x36, 0x24, motion, 1, required},\
/*27*/ {"select rate [or format]",   0x03, 0x01, mode,   0, required /* [ccs2] */},\
/*28*/ {"enter diag mode 1",         0x00, 0x00, mode,   0, discretional},\
/*29*/ {"enter diag mode 2",         0x00, 0x00, mode,   0, discretional},\
/*30*/ {"enter primary mode",        0x00, 0x00, mode,   0, required},\
/*31*/ {"vendor unique (31)",        0x00, 0x00, unused, 0, discretional},\
/*32*/ {"report vendor id",          0x00, 0x00, report, 0, required},\
/*33*/ {"report tape status",        0x04, 0x04, report, 0, ccs1},\
/*34*/ {"skip extended reverse",     0x36, 0x24, motion, 1, ccs1},\
/*35*/ {"skip extended forward",     0x36, 0x24, motion, 1, ccs1},\
/*36*/ {"calibrate tape length",     0x17, 0x05, motion, 1, ccs2},\
/*37*/ {"report format segments",    0x17, 0x05, report, 0, ccs2},\
/*38*/ {"set format segments",       0x17, 0x05, mode,   0, ccs2},\
/*39*/ {"reserved (39)",             0x00, 0x00, unused, 0, discretional},\
/*40*/ {"vendor unique (40)",        0x00, 0x00, unused, 0, discretional},\
/*41*/ {"vendor unique (41)",        0x00, 0x00, unused, 0, discretional},\
/*42*/ {"vendor unique (42)",        0x00, 0x00, unused, 0, discretional},\
/*43*/ {"vendor unique (43)",        0x00, 0x00, unused, 0, discretional},\
/*44*/ {"vendor unique (44)",        0x00, 0x00, unused, 0, discretional},\
/*45*/ {"vendor unique (45)",        0x00, 0x00, unused, 0, discretional},\
/*46*/ {"phantom select",            0x00, 0x00, mode,   0, discretional},\
/*47*/ {"phantom deselect",          0x00, 0x00, mode,   0, discretional},\
}
 
/*
 *      Status bits returned by QIC_REPORT_DRIVE_STATUS
 */
 
#define QIC_STATUS_READY	0x01	/* Drive is ready or idle. */
#define QIC_STATUS_ERROR	0x02	/* Error detected, must read
					   error code to clear this */
#define QIC_STATUS_CARTRIDGE_PRESENT 0x04	/* Tape is present */
#define QIC_STATUS_WRITE_PROTECT 0x08	/* Tape is write protected */
#define QIC_STATUS_NEW_CARTRIDGE 0x10	/* New cartridge inserted, must
					   read error status to clear. */
#define QIC_STATUS_REFERENCED	0x20	/* Cartridge appears to have been
					   formatted. */
#define QIC_STATUS_AT_BOT	0x40	/* Cartridge is at physical
					   beginning of tape. */
#define QIC_STATUS_AT_EOT	0x80	/* Cartridge is at physical end
					   of tape. */
/*
 *      Status bits returned by QIC_REPORT_DRIVE_CONFIGURATION
 */
 
#define QIC_CONFIG_RATE_MASK	0x18
#define QIC_CONFIG_RATE_SHIFT	3
#define QIC_CONFIG_RATE_250	0
#define QIC_CONFIG_RATE_500	2
#define QIC_CONFIG_RATE_1000	3
#define QIC_CONFIG_RATE_2000	1
 
#define QIC_CONFIG_LONG		0x40	/* Extra Length Tape Detected */
#define QIC_CONFIG_80		0x80	/* QIC-80 detected. */
 
/*
 *      Status bits returned by QIC_REPORT_TAPE_STATUS
 */
 
#define QIC_TAPE_STD_MASK       0x0f
#define QIC_TAPE_QIC40  	0x01
#define QIC_TAPE_QIC80  	0x02
#define QIC_TAPE_QIC3020  	0x03
#define QIC_TAPE_QIC3010  	0x04
 
#define QIC_TAPE_LEN_MASK       0x70
#define QIC_TAPE_205FT          0x10
#define QIC_TAPE_307FT          0x20
#define QIC_TAPE_400FT          0x30
#define QIC_TAPE_1100FT         0x40
#define QIC_TAPE_FLEX		0x60
 
#define QIC_TAPE_WIDE		0x80
 
/*
 *      Errors: List of error codes, and their severity.
 */
 
typedef struct {
	char *message;		/* Text describing the error. */
	int fatal;		/* Non-zero if the error is fatal. */
} ftape_error;
 
#define QIC117_ERRORS {\
  /* 0*/ { "No error", 0, },\
  /* 1*/ { "Command Received while Drive Not Ready", 0, },\
  /* 2*/ { "Cartridge Not Present or Removed", 1, },\
  /* 3*/ { "Motor Speed Error (not within 1%)", 1, },\
  /* 4*/ { "Motor Speed Fault (jammed, or gross speed error", 1, },\
  /* 5*/ { "Cartridge Write Protected", 1, },\
  /* 6*/ { "Undefined or Reserved Command Code", 1, },\
  /* 7*/ { "Illegal Track Address Specified for Seek", 1, },\
  /* 8*/ { "Illegal Command in Report Subcontext", 0, },\
  /* 9*/ { "Illegal Entry into a Diagnostic Mode", 1, },\
  /*10*/ { "Broken Tape Detected (based on hole sensor)", 1, },\
  /*11*/ { "Warning--Read Gain Setting Error", 1, },\
  /*12*/ { "Command Received While Error Status Pending (obs)", 1, },\
  /*13*/ { "Command Received While New Cartridge Pending", 1, },\
  /*14*/ { "Command Illegal or Undefined in Primary Mode", 1, },\
  /*15*/ { "Command Illegal or Undefined in Format Mode", 1, },\
  /*16*/ { "Command Illegal or Undefined in Verify Mode", 1, },\
  /*17*/ { "Logical Forward Not a Logical BOT or no Format Segments in Format Mode", 1, },\
  /*18*/ { "Logical EOT Before All Segments generated", 1, },\
  /*19*/ { "Command Illegal When Cartridge Not Referenced", 1, },\
  /*20*/ { "Self-Diagnostic Failed (cannot be cleared)", 1, },\
  /*21*/ { "Warning EEPROM Not Initialized, Defaults Set", 1, },\
  /*22*/ { "EEPROM Corrupted or Hardware Failure", 1, },\
  /*23*/ { "Motion Time-out Error", 1, },\
  /*24*/ { "Data Segment Too Long -- Logical Forward or Pause", 1, },\
  /*25*/ { "Transmit Overrun (obs)", 1, },\
  /*26*/ { "Power On Reset Occurred", 0, },\
  /*27*/ { "Software Reset Occurred", 0, },\
  /*28*/ { "Diagnostic Mode 1 Error", 1, },\
  /*29*/ { "Diagnostic Mode 2 Error", 1, },\
  /*30*/ { "Command Received During Non-Interruptible Process", 1, },\
  /*31*/ { "Rate or Format Selection Error", 1, },\
  /*32*/ { "Illegal Command While in High Speed Mode", 1, },\
  /*33*/ { "Illegal Seek Segment Value", 1, },\
  /*34*/ { "Invalid Media", 1, },\
  /*35*/ { "Head Positioning Failure", 1, },\
  /*36*/ { "Write Reference Burst Failure", 1, },\
  /*37*/ { "Prom Code Missing", 1, },\
  /*38*/ { "Invalid Format", 1, },\
  /*39*/ { "EOT/BOT System Failure", 1, },\
  /*40*/ { "Prom A Checksum Error", 1, },\
  /*41*/ { "Drive Wakeup Reset Occurred", 1, },\
  /*42*/ { "Prom B Checksum Error", 1, },\
  /*43*/ { "Illegal Entry into Format Mode", 1, },\
}
 
#endif				/* _QIC117_H */