Subversion Repositories or1k_old

/*
 * Hardware specific macros, defines and structures
 */
 
#ifndef HARDWARE_H
#define HARDWARE_H
 
#include <asm/param.h>			/* For HZ */
 
/*
 * General hardware parameters common to all ISA adapters
 */
 
#define MAX_CARDS	4		/* The maximum number of cards to
					   control or probe for. If you change
					   this, you must also change the number
					   of elements in io, irq, and ram to
					   match. Initialized in init.c */
/*
extern unsigned int io[];
extern unsigned char irq[];
extern unsigned long ram[];
*/
 
#define SIGNATURE	0x87654321	/* Board reset signature */
#define SIG_OFFSET	0x1004		/* Where to find signature in shared RAM */
#define TRACE_OFFSET	0x1008		/* Trace enable word offset in shared RAM */
#define BUFFER_OFFSET	0x1800		/* Beginning of buffers */
 
/* I/O Port parameters */
#define IOBASE_MIN	0x180		/* Lowest I/O port address */
#define IOBASE_MAX	0x3C0		/* Highest I/O port address */
#define IOBASE_OFFSET	0x20		/* Inter-board I/O port gap used during
					   probing */
#define FIFORD_OFFSET	0x0
#define FIFOWR_OFFSET	0x400
#define FIFOSTAT_OFFSET	0x1000
#define RESET_OFFSET	0x2800
#define PG0_OFFSET	0x3000		/* Offset from I/O Base for Page 0 register */
#define PG1_OFFSET	0x3400		/* Offset from I/O Base for Page 1 register */
#define PG2_OFFSET	0x3800		/* Offset from I/O Base for Page 2 register */
#define PG3_OFFSET	0x3C00		/* Offset from I/O Base for Page 3 register */
 
#define FIFO_READ	0		/* FIFO Read register */
#define FIFO_WRITE	1		/* FIFO Write rgister */
#define LO_ADDR_PTR	2		/* Extended RAM Low Addr Pointer */
#define HI_ADDR_PTR	3		/* Extended RAM High Addr Pointer */
#define NOT_USED_1	4
#define FIFO_STATUS	5		/* FIFO Status Register */
#define NOT_USED_2	6
#define MEM_OFFSET	7
#define SFT_RESET	10		/* Reset Register */
#define EXP_BASE	11		/* Shared RAM Base address */
#define EXP_PAGE0	12		/* Shared RAM Page0 register */
#define EXP_PAGE1	13		/* Shared RAM Page1 register */
#define EXP_PAGE2	14		/* Shared RAM Page2 register */
#define EXP_PAGE3	15		/* Shared RAM Page3 register */
#define IRQ_SELECT	16		/* IRQ selection register */
#define MAX_IO_REGS	17		/* Total number of I/O ports */
 
/* FIFO register values */
#define RF_HAS_DATA	0x01		/* fifo has data */
#define RF_QUART_FULL	0x02		/* fifo quarter full */
#define RF_HALF_FULL	0x04		/* fifo half full */
#define RF_NOT_FULL	0x08		/* fifo not full */
#define WF_HAS_DATA	0x10		/* fifo has data */
#define WF_QUART_FULL	0x20		/* fifo quarter full */
#define WF_HALF_FULL	0x40		/* fifo half full */
#define WF_NOT_FULL	0x80		/* fifo not full */
 
/* Shared RAM parameters */
#define SRAM_MIN	0xC0000         /* Lowest host shared RAM address */
#define SRAM_MAX	0xEFFFF         /* Highest host shared RAM address */
#define SRAM_PAGESIZE	0x4000		/* Size of one RAM page (16K) */
 
/* Shared RAM buffer parameters */
#define BUFFER_SIZE	0x800		/* The size of a buffer in bytes */
#define BUFFER_BASE	BUFFER_OFFSET	/* Offset from start of shared RAM
					   where buffer start */
#define BUFFERS_MAX	16		/* Maximum number of send/receive
					   buffers per channel */
#define HDLC_PROTO	0x01		/* Frame Format for Layer 2 */
 
#define BRI_BOARD	0
#define POTS_BOARD	1
#define PRI_BOARD	2
 
/*
 * Specific hardware parameters for the DataCommute/BRI
 */
#define BRI_CHANNELS	2		/* Number of B channels */
#define BRI_BASEPG_VAL	0x98
#define BRI_MAGIC	0x60000		/* Magic Number */
#define BRI_MEMSIZE	0x10000		/* Ammount of RAM (64K) */
#define BRI_PARTNO	"72-029"
#define BRI_FEATURES	ISDN_FEATURE_L2_HDLC | ISDN_FEATURE_L3_TRANS;
/*
 * Specific hardware parameters for the DataCommute/PRI
 */
#define PRI_CHANNELS	23		/* Number of B channels */
#define PRI_BASEPG_VAL	0x88
#define PRI_MAGIC	0x20000		/* Magic Number */
#define PRI_MEMSIZE	0x100000	/* Amount of RAM (1M) */
#define PRI_PARTNO	"72-030"
#define PRI_FEATURES	ISDN_FEATURE_L2_HDLC | ISDN_FEATURE_L3_TRANS;
 
/*
 * Some handy macros
 */
 
/* Return the number of jiffies in a given number of msecs */
#define milliseconds(x)	(x/(1000/HZ))
 
/* Determine if a channel number is valid for the adapter */
#define IS_VALID_CHANNEL(y,x)	((x>0) && (x <= adapter[y]->channels))
 
#endif